hi
i flashed a firmware to my s6 edsge all went well unitel hidden.img this is the message in odin
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU1AOCV_G925FCOS1AOCV_G925FXXU1AOCW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> param.bin
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> modem.bin
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
name of firmware:G925FXXU1AOCV_G925FCOS1AOCV_G925FXXU1AOCW_HOME.tar
what should i doo please help
thanks
nouninou said:
hi
i flashed a firmware to my s6 edsge all went well unitel hidden.img this is the message in odin
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU1AOCV_G925FCOS1AOCV_G925FXXU1AOCW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> param.bin
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> modem.bin
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
name of firmware:G925FXXU1AOCV_G925FCOS1AOCV_G925FXXU1AOCW_HOME.tar
what should i doo please help
thanks
Click to expand...
Click to collapse
Dear,
try booting to recovery menu and delete cache & do factory reset then power off the phone, then download the firmware again and flash it.
Regards
also use the latest Odin version available thought it was 3.10.6
Solved?
thuglife said:
also use the latest Odin version available thought it was 3.10.6
Click to expand...
Click to collapse
Did you solve your issue? i am having the exact same problem
Did you guys manage to resolve this - I'm having the same problem.
delete the hidden img
http://forum.xda-developers.com/showthread.php?t=3141455
always the same question..I wrote that I think 6 times or so
i used google search if i had that problem
I have soft bricked my s6 edge thrice already. Every time i fixed it by performing a hard factory data reset. However i needed to let it run out of juice before i could boot into recovery
Thanks guys .. I'll try both suggestions and let you know.
Snowby123 said:
I have soft bricked my s6 edge thrice already. Every time i fixed it by performing a hard factory data reset. However i needed to let it run out of juice before i could boot into recovery
Click to expand...
Click to collapse
press all together... power+home+vol up for recovery and volume down for download Odin mode
I can get ODIN mode, but it won't go into recovery mode.
i11usive said:
I can get ODIN mode, but it won't go into recovery mode.
Click to expand...
Click to collapse
try select reboot from Odin mode..and press the combination
Alex-V said:
try select reboot from Odin mode..and press the combination
Click to expand...
Click to collapse
there doesn't appear to be a reboot option in ODIN, to get out of it, I have to press VOL UP/DOWN, POWER AND HOME
i11usive said:
there doesn't appear to be a reboot option in ODIN, to get out of it, I have to press VOL UP/DOWN, POWER AND HOME
Click to expand...
Click to collapse
if you booted in that mode it gives you the option to enter or reboot..
Ah - I see what you mean .. I've seen the vid on YouTube where the guy does that .. I press VOL UP and then quickly press the VOL DN/HOME/POWER combo and it comes back to the "Error has occurred while updating the device software" screen. Any other way?
i11usive said:
Ah - I see what you mean .. I've seen the vid on YouTube where the guy does that .. I press VOL UP and then quickly press the VOL DN/HOME/POWER combo and it comes back to the "Error has occurred while updating the device software" screen. Any other way?
Click to expand...
Click to collapse
simple in the moment of reboot press and hold the combo with volume up.. brings me into recovery
BTW..you can use adb comment..
adb reboot recovery
Alex-V said:
delete the hidden img
http://forum.xda-developers.com/showthread.php?t=3141455
always the same question..I wrote that I think 6 times or so
i used google search if i had that problem
Click to expand...
Click to collapse
Can you help me solve this problem too? my phone does not boot with a similar problem and i do not know how to delete the recovery.img you talk about
I face a strange problem,i get error ocured i extract hidden,flash it and phone stucks on s6 logo,i see when i flash that i get erro while flashing CM bin
Related
Help I need a of1 tar of stock if anyone has it.
http://forum.xda-developers.com/showthread.php?t=3203361 That should do it.
fudplayers said:
http://forum.xda-developers.com/showthread.php?t=3203361 That should do it.
Click to expand...
Click to collapse
Yeah, I forgot I had a copy of the no wipe of1 on my laptop and already fixed it. Thanks though.
So how do I get xposed on of1 without being able to use a recovery. I finally was able to to get my girls phone rooted again with the of1 update. I molded the dpi, boot animation, and took off AL the vzw and Samsung bull. I just need xposed and to mod the sound. Help?
GamerOnOne said:
Yeah, I forgot I had a copy of the no wipe of1 on my laptop and already fixed it. Thanks though.
So how do I get xposed on of1 without being able to use a recovery. I finally was able to to get my girls phone rooted again with the of1 update. I molded the dpi, boot animation, and took off AL the vzw and Samsung bull. I just need xposed and to mod the sound. Help?
Click to expand...
Click to collapse
Do you happen to have a link to that? I tried that thread they linked and it didn't work
raver's fallacy said:
Do you happen to have a link to that? I tried that thread they linked and it didn't work
Click to expand...
Click to collapse
Link for what? Root?
GamerOnOne said:
Link for what? Root?
Click to expand...
Click to collapse
The no wipe of1?
raver's fallacy said:
The no wipe of1?
Click to expand...
Click to collapse
https://www.androidfilehost.com/?fid=24052804347816632
It will take root away just reroot
GamerOnOne said:
https://www.androidfilehost.com/?fid=24052804347816632
It will take root away just reroot
Click to expand...
Click to collapse
any idea why it would Pass in Odin then black screen on boot after Galaxy logo?
There's a chance I'm on OC1 not OF1... After having Samsung smart switch update the phone froze on the Verizon screen so I assumed I was on OF1.
Odin passes
Phone reboots
Shows the android with the chest plate open, a bar filling. gets 50% then black screen and does galaxy logo for too long.
Then LED is stuck on and black screen.
Options: auto reboot and f. reset time
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> NOBL_OF1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> modem.bin
<ID:0/005> NON-HLOS.bin
<ID:0/005> cache.img.ext4
<ID:0/005> hidden.img.ext4
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
raver's fallacy said:
any idea why it would Pass in Odin then black screen on boot after Galaxy logo?
There's a chance I'm on OC1 not OF1... After having Samsung smart switch update the phone froze on the Verizon screen so I assumed I was on OF1.
Odin passes
Phone reboots
Shows the android with the chest plate open, a bar filling. gets 50% then black screen and does galaxy logo for too long.
Then LED is stuck on and black screen.
Options: auto reboot and f. reset time
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> NOBL_OF1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> modem.bin
<ID:0/005> NON-HLOS.bin
<ID:0/005> cache.img.ext4
<ID:0/005> hidden.img.ext4
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
Try flashing of1 bootloader: http://d-h.st/knjx
GamerOnOne said:
Try flashing of1 bootloader: http://d-h.st/knjx
Click to expand...
Click to collapse
same issue. I'll start my search again
thank you!
raver's fallacy said:
same issue. I'll start my search again
thank you!
Click to expand...
Click to collapse
You might have to face wiping the device.
GamerOnOne said:
You might have to face wiping the device.
Click to expand...
Click to collapse
that's perfectly fine with me. but... I've tried a few stock images. Basically I don't know where to get a full-wipe for of1.
all the flashes I do end up with the same problem, black screen after the galaxy logo.
raver's fallacy said:
that's perfectly fine with me. but... I've tried a few stock images. Basically I don't know where to get a full-wipe for of1.
all the flashes I do end up with the same problem, black screen after the galaxy logo.
Click to expand...
Click to collapse
All you can do is Google. I know you can't flash old tars or you'll get an error if I find anything I'll let you know.
I tried newest uk beta (BTU) recently and i wasn't happy about the battery etc.
Flashed newest lollipop firmware for NEE csc. I have tried so many firmwares and no luck .. :crying:
Do i miss something big time? and i am 100% sure about that firmware is right.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925IDVU2COF8_G925IODD2COF8_G925IDVU2COF8_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Getting this kind of log from odin. note this is copy from another thread, otherwise same but buildnumber is different..
I can't even flash twrp/philz recovery. without getting some error, PIT related.
I can't access recovery by anymeans as it wil boot up to that ''smart switch blablabla'' and pc will say it is not supported etc.
I only can access download-mode.
I have tried flash stock 5.1.1 PIT but it makes no difference.
This is 32gb model. How deep i'm in brown?
Got this working!
First i used odin 3.10.7 -> all fails
Then tried 3.10.6 -> first try successfully only that hidden.img was failed but i extracted from firmware and and flashed it after that.
Hope this helps someone.
if you had used smart switch on your pc, it was a lot easier............:good:
lambik333 said:
if you had used smart switch on your pc, it was a lot easier............:good:
Click to expand...
Click to collapse
Maybe if i would done it in first place, but i didnt. Used odin as it usually will do job. And this case smart switch didnt reconized phone at all. :good:
Hi there,
I am a newbie, i apologize for any noob question or mistake.
I followed these instructions
Instructions from sammobile
Extract (unzip) the firmware file
Download Odin v3.10.7
Extract Odin ZIP file
Open Odin v3.10.7
Reboot Phone in Download Mode (press and hold Home + Power + Volume Down buttons)
Connect phone and wait until you get a blue sign in Odin
Add the firmware file to AP / PDA
Make sure re-partition is NOT ticked
Click the start button, sit back and wait few minutes
Its not a brick phone but this version of Cyanogenmod has a lot of bugs hence i want to flash stock rom. i want to be very careful.
Odin fails to flash stock image.
I am getting following error message.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbl.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> BcmCP.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
Any help would be appreciated. i dont want to brick this phone.
Thank you.
Hi !
After flashing UK Oreo image with the steps provided here on my t-820 (original firmware, stock recovery, no root )
As you can see Odin log shows all OK when i flash
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 4920 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> persist.img.ext4
<ID:0/005> userdata.img.ext4
<ID:0/005> modem.bin
<ID:0/005> adspso.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
but after the tablet restart for the first time after the upgrade it got stuck on bootloop showing samsung logo back and forth and doesnt start at all, ive tried to get into recovery mode but it also gets a bootloop the only option available is get to download mode. I still can get my S3 detected by Odin when i get to download mode.
Please advice.
rayxanber said:
Hi !
After flashing UK Oreo image with the steps provided here on my t-820 (original firmware, stock recovery, no root )
As you can see Odin log shows all OK when i flash
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 4920 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> persist.img.ext4
<ID:0/005> userdata.img.ext4
<ID:0/005> modem.bin
<ID:0/005> adspso.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
but after the tablet restart for the first time after the upgrade it got stuck on bootloop showing samsung logo back and forth and doesnt start at all, ive tried to get into recovery mode but it also gets a bootloop the only option available is get to download mode. I still can get my S3 detected by Odin when i get to download mode.
Please advice.
Click to expand...
Click to collapse
The UK-version of Oreo DOESN'T have USERDATA
Put the files in BL AP & CSC (CSC_BTU or HOME_CSC_BTU)
Re:
THANKS !!!
In fact i've only use the PDA file while flashing, i'll try adding the files you mention.
I had the same problem, but then I just flashed the BL and AP and it booted fine after that. Mine failed when I tried with the CSC. Good luck!
Re:
kream21 said:
I had the same problem, but then I just flashed the BL and AP and it booted fine after that. Mine failed when I tried with the CSC. Good luck!
Click to expand...
Click to collapse
Hi !
Did you mean you got a bootloop again after flashing the CSC ? Did you try with both CSC files or just one of them ?
rayxanber said:
Hi !
Did you mean you got a bootloop again after flashing the CSC ? Did you try with both CSC files or just one of them ?
Click to expand...
Click to collapse
No i got a fail. I only used one. When I flashed just the BL and AP I got a pass and everything worked out fine.
Thank you both.
I've flash again using the 3 files and the tablet is working now.
hello friends, I'm italian girl, congratulations for the forum :silly:
my sister have a samsung S6 Edge (buy in the shop Tim in Italy), but suddenly it does not start regularly (infinity bootloop)
it is possible to resurrect it?
My test: (I'm a stubborn girl)
-the battery ok recharge
-recovery- reset factory ok, but not solves!
-can be accessed to Odin mode download, ok
-I could not know the original firmware, then a stroke of genius :victory::silly:...
I have flash the latest firmware available in samMobile[ for samsung edge s6 SM-G925F, firmware ITV (no brand..) android 7]
I used Odin 3, the procedure is successful
The log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 3563 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> modem.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Added!!
<ID:0/004> Removed!!
But after, the device ok rebot, I see android robots- installing system update - the bar loads 0% <25%<32% and immediately after there is the writing "Erasing"....rebot but again BootLoop
I tried an older firmware, but now Odin Fail (I believe it is not possible downgrade firmware, I should have started
with an older firmware...
I'm disaster girl..
someone has some advice for me, before I launch the device from the balcony?
:fingers-crossed::silly:
Thanks
(sorry for my language)
AndroKiss
no help for me?
:crying:
Are you disconnecting the phone or waiting for it to completely finish? Maybe clean out the charge port?
I am not by any means able to correct the issue, but i've never seen a successful odin operation where the device is removed and then completed.
Good news is that it can still go into download mode. So it should not be too difficult to correct. I am assuming you're using latest Odin with the original usb cable and have tried with different ports.
Sometimes it may need a slightly older version of odin to work. You may even have to download the firmware again. Or take it to where you bought it...
But... DO NOT LAUNCH IT!
AndroKiss said:
hello friends, I'm italian girl, congratulations for the forum :silly:
my sister have a samsung S6 Edge (buy in the shop Tim in Italy), but suddenly it does not start regularly (infinity bootloop)
it is possible to resurrect it?
My test: (I'm a stubborn girl)
-the battery ok recharge
-recovery- reset factory ok, but not solves!
-can be accessed to Odin mode download, ok
-I could not know the original firmware, then a stroke of genius :victory::silly:...
I have flash the latest firmware available in samMobile[ for samsung edge s6 SM-G925F, firmware ITV (no brand..) android 7]
I used Odin 3, the procedure is successful
The log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 3563 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> modem.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Added!!
<ID:0/004> Removed!!
But after, the device ok rebot, I see android robots- installing system update - the bar loads 0% <25%<32% and immediately after there is the writing "Erasing"....rebot but again BootLoop
I tried an older firmware, but now Odin Fail (I believe it is not possible downgrade firmware, I should have started
with an older firmware...
I'm disaster girl..
someone has some advice for me, before I launch the device from the balcony?
:fingers-crossed::silly:
Thanks
(sorry for my language)
AndroKiss
Click to expand...
Click to collapse
I suggest download the latest firmware for your phone try flashing it still don't work then try getting the pit file too and firmware and try both?
Since I screwed my s6 edge up as it was not mounting system and cache so I had to get latest firmware, pit file and then in odin tick re-partition and flash then it worked just went into recovery wiped cache and factory reset reboot and done
mindlery said:
Are you disconnecting the phone or waiting for it to completely finish? Maybe clean out the charge port?
I am not by any means able to correct the issue, but i've never seen a successful odin operation where the device is removed and then completed.
Good news is that it can still go into download mode. So it should not be too difficult to correct. I am assuming you're using latest Odin with the original usb cable and have tried with different ports.
Sometimes it may need a slightly older version of odin to work. You may even have to download the firmware again. Or take it to where you bought it...
But... DO NOT LAUNCH IT!
Click to expand...
Click to collapse
thanks mindlery
I disconnecting the phone after Odin> PASS (disconnecting usb)
The usb port is clean (spray contact)
I don't use other port usb and other cable usb, because the Odin procedure it is successful (PASS)
After PASS I disconnect usb, the Phone rebot - it appears android robot- erasing- logo edge -logo samsung,
but nothing done (I waited a long time)
Odin is 3.13.1 (I believe latest version), I have not tried other old versions because the procedure is Ok (Pass)
I worked on this cell phone I believe 30 hours...
I'm a stubborn girl, I do not accept not to recover the phone..
I do not launch it, but the temptation is there
thanks for help
:good:
SomeoneXD said:
I suggest download the latest firmware for your phone try flashing it still don't work then try getting the pit file too and firmware and try both?
Since I screwed my s6 edge up as it was not mounting system and cache so I had to get latest firmware, pit file and then in odin tick re-partition and flash then it worked just went into recovery wiped cache and factory reset reboot and done
Click to expand...
Click to collapse
thanks someone
I'm trying with last firmware for edge (italy- ITV-nogaut7)
it was the first one I tried. and now is impossible using old firmware, cs.bin file no Pass in Odin...
Pit file i read is not necessary for stock firmware, but yesterday I also tried with Pit file (Zerolte eur open hidden60M)
the Odin procedure Pass, but after the phone not installing system ( but maybe I did not reset factory and cache..)
when it is in bootloop, enter in recovery is not easy, and when I go into recovery..I have to be quick to select otherwise the phone hangs...(even with twrp sometimes it crashes)
I do not understand if it's because the phone bootloop, or is the problem hardware (memory flash)
thank s
:victory: