Hi there,
I am a newbie, i apologize for any noob question or mistake.
I followed these instructions
Instructions from sammobile
Extract (unzip) the firmware file
Download Odin v3.10.7
Extract Odin ZIP file
Open Odin v3.10.7
Reboot Phone in Download Mode (press and hold Home + Power + Volume Down buttons)
Connect phone and wait until you get a blue sign in Odin
Add the firmware file to AP / PDA
Make sure re-partition is NOT ticked
Click the start button, sit back and wait few minutes
Its not a brick phone but this version of Cyanogenmod has a lot of bugs hence i want to flash stock rom. i want to be very careful.
Odin fails to flash stock image.
I am getting following error message.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbl.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> BcmCP.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
Any help would be appreciated. i dont want to brick this phone.
Thank you.
Related
hello my friends
i have galaxy s2 i9100g and whener i try to inter the download mode it says recover with kies
but kies doesnt recognise it
i tried to reflash ics rom and used .bit file but it fails everytime
here is my odin diplay cache
please help me if u can
MY Regards
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GJPLP6_I9100GOJPLP5_I9100GXXLPR_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> Sbl.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cache.img
<ID:0/005> factoryfs.img
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Advanced search Hopper8's threads to find his 'Odin doesn't flash successfully' thread. There's a bunch of stuff you can try in there.
The only way you're fixing this is if you get the phone to successfully take an Odin flash, unless you want to take it to a service centre where they'll flash the most recent firmware they have to the phone.
Hi everyone, i firstly apologize if i'm on the wrong page with this question but i'm desperate and totally new to all of this, in way over my head really.
Here is my problem i have rooted my S6 Edge then i wanted to install TWRP Recovery before installing Xposed?...
But what happened is, my device got stuck during TWRP (i used Flashify).
After failing i looked for answers online i'v dowloaded Odin .6 and .7 i went into Odin mode and tried to flash stock firmware SM-G925FXXU3QOKN but it failed near finishing on both Odins. Now i'm not even sure anymore whether anything after "SM-G925FXXU3" is right or whether it even matters because i couldn't find the firmware for my country but on sammobile the firmwares of all our neighbouring countries end on "QOKN" so i guess what are the odds?
Now my device doesnt startup at all, unless it's plugged into the pc it displays a BLUE SCREEN: "An error has occured while updating the device software. Use the Emergency recovery function in the Smart Switch PC software"
(Smart Switch doesn't give me any options, Samsung kies is disabled by Samsung)
while the device is plugged in and showing the text i can get into Odin mode.
If anyone of you guys could help me out, that would mean a lot to me.
Thanks in advance.
EDIT; My device was running 5.1.1 lollipop
Odin;
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Hi Jamie, you probably have the right firmware BUT right after you've flashed the firmware and it fails at "hidden.img" you need to open the firmware file you have flashed and extract the "hidden.img" file.
Okay, when you have done so rename the file to "hidden.img.tar" (you may receive a warning that the file may become damaged)
Don't worry, proceed!
When the file is renamed, open Odin and add the hidden.img.tar file to the AP/PDA tab and flash it unto your device.
Be patient.
I tried newest uk beta (BTU) recently and i wasn't happy about the battery etc.
Flashed newest lollipop firmware for NEE csc. I have tried so many firmwares and no luck .. :crying:
Do i miss something big time? and i am 100% sure about that firmware is right.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925IDVU2COF8_G925IODD2COF8_G925IDVU2COF8_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Getting this kind of log from odin. note this is copy from another thread, otherwise same but buildnumber is different..
I can't even flash twrp/philz recovery. without getting some error, PIT related.
I can't access recovery by anymeans as it wil boot up to that ''smart switch blablabla'' and pc will say it is not supported etc.
I only can access download-mode.
I have tried flash stock 5.1.1 PIT but it makes no difference.
This is 32gb model. How deep i'm in brown?
Got this working!
First i used odin 3.10.7 -> all fails
Then tried 3.10.6 -> first try successfully only that hidden.img was failed but i extracted from firmware and and flashed it after that.
Hope this helps someone.
if you had used smart switch on your pc, it was a lot easier............:good:
lambik333 said:
if you had used smart switch on your pc, it was a lot easier............:good:
Click to expand...
Click to collapse
Maybe if i would done it in first place, but i didnt. Used odin as it usually will do job. And this case smart switch didnt reconized phone at all. :good:
i was using odin trying to re install the stock firmwar and it comes up with this error: check fail device:3 binary:1 and on odin it says<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
help me please!
also i tried factory resseting it and i remove the os period ahh
clewesman said:
i was using odin trying to re install the stock firmwar and it comes up with this error: check fail device:3 binary:1 and on odin it says<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
help me please!
also i tried factory resseting it and i remove the os period ahh
Click to expand...
Click to collapse
Can you get into bootloader? If so fire up smart switch on your pc and click over to emergencey recovery and type in your model number and serial number all in capitals and it should download the software and flash it
I've had this happen too me twice,first make sure you flashing the correct firmware,mine worked once I had the official firmware and my phone wouldn't even enter recovery.
Hi !
After flashing UK Oreo image with the steps provided here on my t-820 (original firmware, stock recovery, no root )
As you can see Odin log shows all OK when i flash
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 4920 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> persist.img.ext4
<ID:0/005> userdata.img.ext4
<ID:0/005> modem.bin
<ID:0/005> adspso.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
but after the tablet restart for the first time after the upgrade it got stuck on bootloop showing samsung logo back and forth and doesnt start at all, ive tried to get into recovery mode but it also gets a bootloop the only option available is get to download mode. I still can get my S3 detected by Odin when i get to download mode.
Please advice.
rayxanber said:
Hi !
After flashing UK Oreo image with the steps provided here on my t-820 (original firmware, stock recovery, no root )
As you can see Odin log shows all OK when i flash
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 4920 M
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NAND Write Start!!
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> persist.img.ext4
<ID:0/005> userdata.img.ext4
<ID:0/005> modem.bin
<ID:0/005> adspso.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
but after the tablet restart for the first time after the upgrade it got stuck on bootloop showing samsung logo back and forth and doesnt start at all, ive tried to get into recovery mode but it also gets a bootloop the only option available is get to download mode. I still can get my S3 detected by Odin when i get to download mode.
Please advice.
Click to expand...
Click to collapse
The UK-version of Oreo DOESN'T have USERDATA
Put the files in BL AP & CSC (CSC_BTU or HOME_CSC_BTU)
Re:
THANKS !!!
In fact i've only use the PDA file while flashing, i'll try adding the files you mention.
I had the same problem, but then I just flashed the BL and AP and it booted fine after that. Mine failed when I tried with the CSC. Good luck!
Re:
kream21 said:
I had the same problem, but then I just flashed the BL and AP and it booted fine after that. Mine failed when I tried with the CSC. Good luck!
Click to expand...
Click to collapse
Hi !
Did you mean you got a bootloop again after flashing the CSC ? Did you try with both CSC files or just one of them ?
rayxanber said:
Hi !
Did you mean you got a bootloop again after flashing the CSC ? Did you try with both CSC files or just one of them ?
Click to expand...
Click to collapse
No i got a fail. I only used one. When I flashed just the BL and AP I got a pass and everything worked out fine.
Thank you both.
I've flash again using the 3 files and the tablet is working now.