I installed Android L Themed by Pinto in my Canvas Nitro A310.
One day it worked fine. Later it started rebooting and started behaving Rogue.
a) While trying to charge,it shows a Low Battery Sign (Red) and goes into the Android + Micromax Logo for 2-4 seconds then reboots to Low Battery Sign and then Android+Micromax Logo and then reboots. My Phone is unable to come out of this endless cycle.
b) No Recovery available on pressing Power Up + Vol Down.
c)I tried downloading Stock ROM and installed all drivers.
While trying to install Stock ROm; I get a window of 5-6 seconds for flash before it gets automatically dislinked.
In this flashing process using YGDP; it failed to recognise the device inspite of Preloader VCOM installed.
While using SP tool; the device gets detected only between 4-5 seconds and gets frozen with error 2035. (JUMP_DA_FAIL)
Any idea How to proceed ??
Prabhakar
Which recovery did you have on your phone before this boot loop?
Try pressing the volume up + power key instead of the volume down key.
prabhu1980 said:
I installed Android L Themed by Pinto in my Canvas Nitro A310.
One day it worked fine. Later it started rebooting and started behaving Rogue.
a) While trying to charge,it shows a Low Battery Sign (Red) and goes into the Android + Micromax Logo for 2-4 seconds then reboots to Low Battery Sign and then Android+Micromax Logo and then reboots. My Phone is unable to come out of this endless cycle.
b) No Recovery available on pressing Power Up + Vol Down.
c)I tried downloading Stock ROM and installed all drivers.
While trying to install Stock ROm; I get a window of 5-6 seconds for flash before it gets automatically dislinked.
In this flashing process using YGDP; it failed to recognise the device inspite of Preloader VCOM installed.
While using SP tool; the device gets detected only between 4-5 seconds and gets frozen with error 2035. (JUMP_DA_FAIL)
Any idea How to proceed ??
Prabhakar
Click to expand...
Click to collapse
ust download your offcial rom from needrom.com and download ygdp and install it the password will be 369 after installing go in conf. and there select the cpb with after extracting the downloaded rom after config. it will take some time then click on start and then connect your phone wait after completing jst switch it on
hit thanks it will work 200%
Suman117 said:
ust download your offcial rom from needrom.com and download ygdp and install it the password will be 369 after installing go in conf. and there select the cpb with after extracting the downloaded rom after config. it will take some time then click on start and then connect your phone wait after completing jst switch it on
hit thanks it will work 200%
Click to expand...
Click to collapse
my phone connect for 3 or 4 seconds and then disconnect
tell me what should i do
prabhu1980 said:
While using SP tool; the device gets detected only between 4-5 seconds and gets frozen with error 2035. (JUMP_DA_FAIL)
Any idea How to proceed ??
Click to expand...
Click to collapse
Use SPflash 5, battery inserted, phone turned off, in SP select upgrade firmware, click downolad and press volume+ on your phone and connect phone to pc usb, how to fly the red bar (flash start) you release the key volume +, it should already process to the end, sometimes detects the usb 1 connection and it takes a long time
Related
I have a strange situation with my Razr XT910, let me explain to you guys and please tell me what to do:
1- My Razr was on 2.3.6
2- I rooted it, but I cannot remember which method as I tried many ways and cannot really remember which one succeeded.
3- After rooting I flashed a 4.0.4 AOKP-GSM-J.Y.Daddy rom
4- I have several issues with the rom so I want to install another rom, so I tried Eternity project rom. It didn't work and gives me message "Installation aborted", so I gave up.
5- Decided to go back to stock rom, so downloaded the right SBF and RSD lite.
6- I put the USB debugging on
7- I turned my phone off and go to boot loader mod by holding Volume +/- and power buttons and go to SBF flash, connect the USB cable and hear the notification sound from my laptop. No message received from the PC saying installing device. Receive message from RSD USB connected and one clicked show device it gives everything N/A
8- Uncompressed the SBF and pressed start. Then process FAIL
9- Now, tried to turn the phone on, I have to go to to Fastboot mode and press power long then screen goes off. Then I press volume +/- with power again to go to bootloader mode then choose normal reboot to turn my phone back.
10- Tried the above steps over than 30 times for 2 days. Suddenly I discovered that my phone is unrooted when I tried to install any app requires rooting such as Titanium.
My ICS works fine with some bugs, I still wants to go back.
Can any one help me, I explained everything I'm going through.
Appreciated.
flupo2000 said:
I have a strange situation with my Razr XT910, let me explain to you guys and please tell me what to do:
1- My Razr was on 2.3.6
2- I rooted it, but I cannot remember which method as I tried many ways and cannot really remember which one succeeded.
3- After rooting I flashed a 4.0.4 AOKP-GSM-J.Y.Daddy rom
4- I have several issues with the rom so I want to install another rom, so I tried Eternity project rom. It didn't work and gives me message "Installation aborted", so I gave up.
5- Decided to go back to stock rom, so downloaded the right SBF and RSD lite.
6- I put the USB debugging on
7- I turned my phone off and go to boot loader mod by holding Volume +/- and power buttons and go to SBF flash, connect the USB cable and hear the notification sound from my laptop. No message received from the PC saying installing device. Receive message from RSD USB connected and one clicked show device it gives everything N/A
8- Uncompressed the SBF and pressed start. Then process FAIL
9- Now, tried to turn the phone on, I have to go to to Fastboot mode and press power long then screen goes off. Then I press volume +/- with power again to go to bootloader mode then choose normal reboot to turn my phone back.
10- Tried the above steps over than 30 times for 2 days. Suddenly I discovered that my phone is unrooted when I tried to install any app requires rooting such as Titanium.
My ICS works fine with some bugs, I still wants to go back.
Can any one help me, I explained everything I'm going through.
Appreciated.
Click to expand...
Click to collapse
Unplug razr from pc
Uninstall all razr software
Reinstall motocast 1.29
Plug razr, let drivers reinstall
Turn it of
Go into fastboot menu
Wait drivers reinstall
Flash .sbf
Cheers
Sent from my XT910 using Tapatalk 2
Thanks dear, that's exactly what I did 30 times and I keep getting same message on RSD "FAIL"
Now I tried this http://forum.xda-developers.com/showthread.php?t=1486718
and choose # 1 restore EU GSM and I was stuck in a boot loading loop.
Any time I try an option with my phone I go to this screen:
AP Fastboot Flash Mode (s) (Flash Failure)
OA.GC
To return to normal mode-first press power key to power down
Device is LOCKED. Status Code:0
Battery OK
OK to Program
Connect USB
Data Cable
flupo2000 said:
Thanks dear, that's exactly what I did 30 times and I keep getting same message on RSD "FAIL"
Now I tried this http://forum.xda-developers.com/showthread.php?t=1486718
and choose # 1 restore EU GSM and I was stuck in a boot loading loop.
Any time I try an option with my phone I go to this screen:
AP Fastboot Flash Mode (s) (Flash Failure)
OA.GC
To return to normal mode-first press power key to power down
Device is LOCKED. Status Code:0
Battery OK
OK to Program
Connect USB
Data Cable
Click to expand...
Click to collapse
Try this
http://forum.xda-developers.com/showthread.php?t=1453660
Sent from my XT910 using Tapatalk 2
pedrotorresfilho said:
Try this
http://forum.xda-developers.com/showthread.php?t=1453660
Sent from my XT910 using Tapatalk 2
Click to expand...
Click to collapse
Thanks again,
I forced it to close then it was booted to a screen (not CWmod) which enabled me to wipe the data and restore factory sittings and it worked. Now the phone like brand new and I installed the update to 2.3.6
Hi
FYI my xperia X10 was on a GB stock Rom and I was facing some bugs like:
1- When I plug in to the charger, the phone starts and go the home-screen and the Lock-screen (which I really hate and It shouldn't do that)
2- When I check the screen auto-rotation check box, the auto-rotation works for a while then disabling itself
3- freezes and restart a lot
4- The battery after full charging lasts for 2 hours max (the problem here is the battery not the software)
So I decided to change the Rom. I found that the device was having CWM recovery on it. And here what I did:
1- I made a full backup, and it was successful.
2- Full and Clean wipe (factroy, data, /system, /cache, /data, dalvik) for every thing except the sdcard format and SD-ext format.
3- I start to flash the custom Rom using CWM.
4- The famous error occurred the Status 7 error (It was the first time for me to face this error).
5- I accidentally restart the phone.
Since then when I turn on the phone, all I get is the "Sony Ericsson" log screen and nothing after. I can't even reach the CWM again.
When I plug it the pc it is not recognized by the pc by any means and in any mode (flash mode, fastboot mode), not even an yellow error mark on the device manager.
Recently the battery is empty and when I charge it the Red LED blink (I think because It is trying to start up) after few minutes the blinking Red LED turns to constant Green LED and after few more minutes the green LED is off and the phone start up and reach the "Sony Ericsson" log screen and stay on it for 10 seconds then the phone is off and the blinking Red LED return again and I am in a circle without an end.
Note:
The Flashtool didn't recognize the phone even after installing the driver.
When I open flashtool on my PC and I press the flash device button (the thunder one), choosing the flashmode then choosing a stock firmware I downloaded then pressing flash. The "Waiting for Flashmode" window pop up and the animated instruction is working normally but when I try connect the phone while pressing the back button, the animated instruction goes extremely fast few times then return to normal and the phone still not recognized.
Please help me
Thank you for your time
Eklado said:
The Flashtool didn't recognize the phone even after installing the driver.
When I open flashtool on my PC and I press the flash device button (the thunder one), choosing the flashmode then choosing a stock firmware I downloaded then pressing flash. The "Waiting for Flashmode" window pop up and the animated instruction is working normally but when I try connect the phone while pressing the back button, the animated instruction goes extremely fast few times then return to normal and the phone still not recognized.
Click to expand...
Click to collapse
I suggest that you get a new battery as I faced similar issues with my previous (old, 2 hr life) battery
and
recover the phone through SEUS:
http://www.sonymobile.com/global-en/tools/update-service/
good luck
Yesterday I rooted my LG Optimus L9 using LGpwn tool, after that it worked just fine.
This morning I tried to install ClockworkMod Recovery. Using this post. It explains how to download and install CWM Recovery from app that you downloaded in form of APK.
This method did not work 100%, but I was able to reboot normally, so in post it said that sometimes it does not work and you need to download and use Busybox installer Link to busyboxx.
After this I managed to boot in too CWM using app from mentioned thread.
Then problem occurred. After I saw CWM was working I selected reboot device option.
Except now when it started to boot it stops right after Second LG logo (First is static one second one is animated).
I get white screen with "Encrypting" on top and gray line. And one Reset Phone button. IMG they are Dropbox links.
This is followed with Error : Unfortunately, the process com.android.phone has stopped. IMG
I am able to boot in too CWM and I have tried flashing something like Cyanogenmod but I get error Status 7. Tried removing line that checks model, no use.
Tried clearing every cache and fixing permissions, nothing. Formatted everything still no use.
Dear XDA community That you in advance.
I fixed my phone by going into SW upgrade mode, and using the Upgrade Recovery function of the LG Software Update tool or whatever. Be sure you don't have any http servers open
Sent from my LG-P769 using XDA Premium 4 mobile app
I got the same problem, but when I try to access to SW mode and connect to LG Software Update tool to restore my phone, the phone keep disconnect and the phone screen will turn off, so I fail to restore my phone, I have already re-install the USB driver and changed a several USB cable but the problem still, but I tried to restore my phone with SW upgrade method since last night and is was OK, can anyone help me?
---------------------------------------------------------------------------
The Problem Solve Finally, the solution is I plug the battery back to the phone after access to LGMobile Support Tool, and after finish the restore process, the phone will restart but keep boot loop, then I perform the hard reset (Remove the Battery and insert it after few seconds. And now do the 3 button HARD RESET. First press VOLUMEDOWN and HOMEbutton. Then Press Power button only for 3 seconds and release power button but dont release VolDown and Home button and KEEP BOTH PRESSING until you see a Bigger Green Standing Android and circulating Molecular structure above it. DONE! ), then the phone begin work~~~
pigmich said:
I got the same problem, but when I try to access to SW mode and connect to LG Software Update tool to restore my phone, the phone keep disconnect and the phone screen will turn off, so I fail to restore my phone, I have already re-install the USB driver and changed a several USB cable but the problem still, but I tried to restore my phone with SW upgrade method since last night and is was OK, can anyone help me?
---------------------------------------------------------------------------
The Problem Solve Finally, the solution is I plug the battery back to the phone after access to LGMobile Support Tool, and after finish the restore process, the phone will restart but keep boot loop, then I perform the hard reset (Remove the Battery and insert it after few seconds. And now do the 3 button HARD RESET. First press VOLUMEDOWN and HOMEbutton. Then Press Power button only for 3 seconds and release power button but dont release VolDown and Home button and KEEP BOTH PRESSING until you see a Bigger Green Standing Android and circulating Molecular structure above it. DONE! ), then the phone begin work~~~
Click to expand...
Click to collapse
I had this problem too...
You can also try, start upgrade tool, Remove battery -> press volume up + insert usb with upgrade tool open, it will detect, insert battery then go to extras and click upgrade-foutherstel (is in dutch for me)
Then it will all work, I can't even install a custom rom My bootloader is unlocked, rooted phone, installed recovery, see my thread about the error I get!! please!
help lg p768 encrypting error problem
can someone help me please.
i have the same problem from the starter of this thread..
installed recovery apk and goes to encrypting error.
i dont know what to do and how to begin to solve my phone problem.
thanks
HEy guys after rooting my phone and booting it up it worked fine. After a couple days i decided to flash a custom rom to it. All went well and after flashing is said to reboot. After it shut down there was nothing. I cant boot to recovery or even to the LG logo. After holding down the power and volume down button for 20 seconds the red led will blink for 8 seconds...then 8 seconds more and it will do that for ever. Plugging it into my computer the computer will open up like 15 partitions. saying i need to format before i can use it. Now i did back up the phone before flashing and i have the file on my computer. How can I fix this?
themightyandroid said:
HEy guys after rooting my phone and booting it up it worked fine. After a couple days i decided to flash a custom rom to it. All went well and after flashing is said to reboot. After it shut down there was nothing. I cant boot to recovery or even to the LG logo. After holding down the power and volume down button for 20 seconds the red led will blink for 8 seconds...then 8 seconds more and it will do that for ever. Plugging it into my computer the computer will open up like 15 partitions. saying i need to format before i can use it. Now i did back up the phone before flashing and i have the file on my computer. How can I fix this?
Click to expand...
Click to collapse
Try to enter download mode. If your computer can detect the phone, then you can try to flash it manually.
Download LG G2 Stock Firmware. You can google it because I still cannot include link on my post.
How to enter download mode:
Turn off the phone. In your case you can pull your battery out, wait for 5 seconds, and then reinsert the battery.
Press volume up while connecting the USB cable connected to the computer.
Install LG G2 driver. (See attachment)
Flash it using flash tool. (See attachment)
How to flash manually:
Run the UpTestEX.exe.
Change Select Type into "3GQCT".
Change PhoneMode into “DIAG”.
Select kdz file (Stock Firmware that you want to flash)
Click on the “NORMAL WEB UPGRADE TEST” button.
Click on the “Upgrade Start” button.
On “Select Country & Language” choose Republic of Korea, select English as default language and proceed.
Wait for the flashing process, in the end your phone will reboot automatically.
Unplug your phone when you are done.
Cinus1985 said:
Try to enter download mode. If your computer can detect the phone, then you can try to flash it manually.
Download LG G2 Stock Firmware. You can google it because I still cannot include link on my post.
How to enter download mode:
Turn off the phone. In your case you can pull your battery out, wait for 5 seconds, and then reinsert the battery.
Press volume up while connecting the USB cable connected to the computer.
Install LG G2 driver. (See attachment)
Flash it using flash tool. (See attachment)
How to flash manually:
Run the UpTestEX.exe.
Change Select Type into "3GQCT".
Change PhoneMode into “DIAG”.
Select kdz file (Stock Firmware that you want to flash)
Click on the “NORMAL WEB UPGRADE TEST” button.
Click on the “Upgrade Start” button.
On “Select Country & Language” choose Republic of Korea, select English as default language and proceed.
Wait for the flashing process, in the end your phone will reboot automatically.
Unplug your phone when you are done.
Click to expand...
Click to collapse
Thanksman However there is a problem i seem unable to get to download mode. My screen dosent show anything no LG symbol or anything. Only the backlight of the phone lights up. Any other methods of getting to download mode? Theccomputer says the drivers arent installed but they are. The computer recognizes it as QHSUSB_BULK. I am downloading the 2.1GB kdz file right now for it.
themightyandroid said:
Thanksman However there is a problem i seem unable to get to download mode. My screen dosent show anything no LG symbol or anything. Only the backlight of the phone lights up. Any other methods of getting to download mode? Theccomputer says the drivers arent installed but they are. The computer recognizes it as QHSUSB_BULK. I am downloading the 2.1GB kdz file right now for it.
Click to expand...
Click to collapse
Check this thread:
http://forum.xda-developers.com/showthread.php?t=2582142
Hello to all,I am in a serious trouble with my samsung galaxy player 5.0 International China version . I rooted this with super one click.And it was successful and there was no problem.But as soon as I overwrote a file in lib folder of system,it got stuck.I tapped the power key and the screens light was gone.I again tapped but there was no response.So I held the power key for a while and the device restarted.But it got stuck on samsung logo and began to restart again and again.So I took it to download mode and tried to nand erase with odin,I thought it could format the device and my device would be fixed.But it took some time and I closed odin.Then I held the power key and it restarted with a black screen containing a picture of malfunctioning connection between a phone and computer at its middle.Then I again tried to t-flash it and again closed it without completion because my notebook had no charge.After that I flashed my device with the YP-G70-Kernel-r14 and it restarted with download mode.But if I hold the power key for a while it restart and again go to the brick showing screen(I heard that this brick is called soft brick).I downloaded two stock rom STOCK_G70XXKPH_G70XXKPH_XEF and G70XXKPL_G70XXKPL_XEF.I tried to flash them in my device with odin and they succeeded.But none of them could fix my problem.They remain in download mode and if I hold the power key the device again go to the soft bricked screen.My device isn't force shutting down.If I hold the power key the screen goes and again lights up with the bricked screen.Now,my device has become very hot and after 8-9 hours it has automatically turned off.But if I connect it to the charger it again lighten up with bricked screen.
Now,I am wanting to setup a clean and clear version of android 2.2/2.3.6 in my device.Is it possible?Will this fix my problem?If it does then please explain me the steps.Or if there is any other way to fix then please help me.
N.B. I am junior about andorid root,rom etc.It is the first device I rooted successfully.
Sorry for my bad and wrong English.
Please,help.I am in a bad danger.
BFahim said:
Hello to all,I am in a serious trouble with my samsung galaxy player 5.0 International China version . I rooted this with super one click.And it was successful and there was no problem.But as soon as I overwrote a file in lib folder of system,it got stuck.I tapped the power key and the screens light was gone.I again tapped but there was no response.So I held the power key for a while and the device restarted.But it got stuck on samsung logo and began to restart again and again.So I took it to download mode and tried to nand erase with odin,I thought it could format the device and my device would be fixed.But it took some time and I closed odin.Then I held the power key and it restarted with a black screen containing a picture of malfunctioning connection between a phone and computer at its middle.Then I again tried to t-flash it and again closed it without completion because my notebook had no charge.After that I flashed my device with the YP-G70-Kernel-r14 and it restarted with download mode.But if I hold the power key for a while it restart and again go to the brick showing screen(I heard that this brick is called soft brick).I downloaded two stock rom STOCK_G70XXKPH_G70XXKPH_XEF and G70XXKPL_G70XXKPL_XEF.I tried to flash them in my device with odin and they succeeded.But none of them could fix my problem.They remain in download mode and if I hold the power key the device again go to the soft bricked screen.My device isn't force shutting down.If I hold the power key the screen goes and again lights up with the bricked screen.Now,my device has become very hot and after 8-9 hours it has automatically turned off.But if I connect it to the charger it again lighten up with bricked screen.
Now,I am wanting to setup a clean and clear version of android 2.2/2.3.6 in my device.Is it possible?Will this fix my problem?If it does then please explain me the steps.Or if there is any other way to fix then please help me.
N.B. I am junior about andorid root,rom etc.It is the first device I rooted successfully.
Sorry for my bad and wrong English.
Please,help.I am in a bad danger.
Click to expand...
Click to collapse
remove your battery and wait 20 seconds plug in your charger without battery wait for 30 seconds then plug out charger then put your battery battery back then charge it try to turn it on
hope it helps
BFahim said:
Hello to all,I am in a serious trouble with my samsung galaxy player 5.0 International China version . I rooted this with super one click.And it was successful and there was no problem.But as soon as I overwrote a file in lib folder of system,it got stuck.I tapped the power key and the screens light was gone.I again tapped but there was no response.So I held the power key for a while and the device restarted.But it got stuck on samsung logo and began to restart again and again.So I took it to download mode and tried to nand erase with odin,I thought it could format the device and my device would be fixed.But it took some time and I closed odin.Then I held the power key and it restarted with a black screen containing a picture of malfunctioning connection between a phone and computer at its middle.Then I again tried to t-flash it and again closed it without completion because my notebook had no charge.After that I flashed my device with the YP-G70-Kernel-r14 and it restarted with download mode.But if I hold the power key for a while it restart and again go to the brick showing screen(I heard that this brick is called soft brick).I downloaded two stock rom STOCK_G70XXKPH_G70XXKPH_XEF and G70XXKPL_G70XXKPL_XEF.I tried to flash them in my device with odin and they succeeded.But none of them could fix my problem.They remain in download mode and if I hold the power key the device again go to the soft bricked screen.My device isn't force shutting down.If I hold the power key the screen goes and again lights up with the bricked screen.Now,my device has become very hot and after 8-9 hours it has automatically turned off.But if I connect it to the charger it again lighten up with bricked screen.
Now,I am wanting to setup a clean and clear version of android 2.2/2.3.6 in my device.Is it possible?Will this fix my problem?If it does then please explain me the steps.Or if there is any other way to fix then please help me.
N.B. I am junior about andorid root,rom etc.It is the first device I rooted successfully.
Sorry for my bad and wrong English.
Please,help.I am in a bad danger.
Click to expand...
Click to collapse
I don't have a samsung device myself but if you can get in download mode and you can from what you described. What happened is that you deleted a driver (from the lib folder) that was necessary for boot (something important). To get to stock go here http://forum.xda-developers.com/showthread.php?t=2192488 download the right Firmware for your device. And the right pit file (pit file is the partition layout of the device). Flash using the pit file you got. You will fix that. Good luck.
Stock rom and pit file downloaded
cedie said:
remove your battery and wait 20 seconds plug in your charger without battery wait for 30 seconds then plug out charger then put your battery battery back then charge it try to turn it on
hope it helps
Click to expand...
Click to collapse
So,I am in the download mode.I downloaded the firmware (XXXKPL) and the intl pit file.Now what options would be checked in odin and where will I put the firmware file(PDA or Bootloader)?The device has no charge.If I connect to the charger,it wakes up and becomes very hot than normal.And I can't turn it off.Its battery is non-removable.Thank you for your valuable help.