Related
Just letting you guys know that this phone can survive being fully submerged under hot soup for atleast 5 seconds.
Backstory:
So, I was trying to watch a youtube video ergonomically over lunch in landscape mode. Hitting the volume key with my left hand made the phone slip and fall into my soup. I was in disbelief and took me about 5 seconds to take it out. Phone was still working, I powered it off and took it home to dry for a few hours.
It seemed to manage to turn itself on when I came back to check on it (Probably accidentally powered it back on when i was putting it in rice).
And it still works! I decided to take it apart anyway to clean the internals and remove the condensation on the internal camera lense cover; it was pretty dry inside. I faced a few hiccups taking it apart; Due to the rubbing alcohol I used, the screen came off of its harness and I had to superglue it back on) and I managed to nicked the case trying to pry things out.
I decided to test how much liquid the cavities would allow. For the headphone jack the way the water traversed (from pouring rubbing alcohol into the jack) It flows to the side and into the back panel barely touching the shielded chipsets. The other cavities are pretty well sealed and those areas were dry with no salty residue except for the cavity covers.
All in all, my lumia 800 lived to see another day :victory:
what kinda soup?
poope said:
what kinda soup?
Click to expand...
Click to collapse
It was Vietnamese Pho, chicken broth basically.
Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
The best reason for replacing both is that you won't have to worry about binding them or getting dust between them if you get them together preassembled. As to the rest, I can't say. I know we have a few people here who have done it.
So I found the adhesive strips that I need. It comes as a bulk sheet where you cut them to fit. I am going with replacing only the digitizer. Replacing the LCD screen also would male the process easier however I fear getting a replacement screen that is in worse shape or more poorly made than the original one my phone came with. I know this one has no flaws.
So I have answered my questions already. I'll post here when I done replacing the digitizer with anything that is of interest in case someone else has questions about this procedure.
Thank you for your input shrike1978. Much appreciated.
Regards,
Eduard Tieseler
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
Click to expand...
Click to collapse
Check out my thread: http://forum.xda-developers.com/showthread.php?t=2189789
I did it not long ago, and was fine. However, I opted to go for the digitizer + LCD assembly, as I didn't want to have to worry about separating the digitizer from the LCD and worrying about dust.
To answer your questions:
1) It's eaiser, takes less time, and you don't have to worry about dust with replacing the digitizer + LCD assembly.
2) Replace the adhesive. I tried reusing it... and it has some flex on it. So I got some new adhesive, scraped the old stuff off, put the new one, and used a heatgun to move the screen assembly around to get it to fit right, and then pressed it down as it cooled to secure it better.
3) Ebay
4) Not sure on this one... not that I know of anyway.
5) If you get the parts from eBay, then they sometimes come with tools (Torx, philips, and a plastic separator tool).
I also linked the video that I used in my thread, so you can look at that. It's pretty straightforward and easy to do. Took me about 45 minutes to just over an hour to do everything, as I was taking my time.
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
etieseler said:
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
Click to expand...
Click to collapse
I also purchased the full assembly and was able to switch the new parts onto my Rezound. Unfortunately, the earpiece (the part you listen to when NOT on speakerphone) and the proximity sensor did not work with the new set, and I am swapping it for a replacement. However, I've been inside the unit now 5 times, and I suggest in addition to the tools supplied with the sets (t5, small phillips and separator) you also have a small flathead (helps with starting the split the unit apart and also with pulling and reattaching the vibrator motor) and a long tweezers (invaluable when trying to reconnect the ribbon cables.)
Also, reconnect the MIDDLE ribbon cable (which is slightly twisted and longer) first, then reconnect the top, and don't forget to reapply the insulating tape (been there, done that).
Watch the take apart video on Youtube repeatedly until you can do it with your eyes closed, and be careful, the red plastic does break easily, especially on the corners.
Replaced my digitizer with good success, using new adhesive. Upon first re-assembly the digitizer was popping out of the plastic bezel a bit, but everything worked great, touch, display, everything. So I decided to take apart, add some more adhesive strips. Now the digitizer stays flush.
First boot after 2nd re-assembly, got boot with first vibrate, but no screen on. So I pull the battery to attempt again. Now I receive no vibrate response from power button. When plug into charger, orange light comes on for 5 seconds and then off indefinitely. This happens each time after battery pull+wall charger plugin.
I have tried multiple times disassembling, checking both ribbon cables that plugin to motherboard, appear to connect fine. Visually all other aspects of MB appear fine.
Any ideas anyone? Not sure what may have broke. I should have left well-enough alone, but the digitizer was somewhat spongey to touch on right side of screen and I could see white light shine up... TIA
Each time I pull the batt the orange light will come on solid for 5 or so sec, then off for good. One time even started flashing for a bit like it was charging from full depletion (like it does before it lets you power on). Not sure how to diagnose.
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
Click to expand...
Click to collapse
I did not put those pieces of tape back on. In the YouTube video by "injured gadgets," I don't believe they re-covered up those ribbon cable plugins, so I also did not during re-assembly. Should I try that? Or, I assume, my board somewhere has gone bad? (Phone did work just fine after re-assemble, until I decided to take apart again)
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
hgoldner said:
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
Click to expand...
Click to collapse
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
I would go ahead and try putting it back on. There was an earlier post where someone mentioned it was important to put it back on, perhaps he can comment on what can happen if its not on (He said he learned from experience). Perhaps you can PM him.
To be honest, I originally only put the tape back on one connection, but after the second time replacing both the LCD screen and the digitizer, I found the second piece of tape and now both are back on.
What can it hurt to see if that will fix it? Its fairly easy to get to on these phones.
Ed
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
red3razor said:
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
Click to expand...
Click to collapse
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
carngeX said:
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
Click to expand...
Click to collapse
I left it off on one connection for about a week also with no issues. However I did notice roughly a 16th of an inch of copper exposed on the ribbon. I can envision potential issues from that. I'm not sure about your phone, but the jaw connectors on mine would never open on their own. Far too much resistance to open from any vibration or movement. The vibrator motor connection had a better chance of disconnecting on its own than the ribbon cables. I'm sure that tape provides more than just locking the jaw connectors closed. I could be wrong though.
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
No, I remembered and put it on before I powered up.
Dumped down the innertubes from my Asus Transformer TF300T
Just replaced my digitizer two days ago and I must add the difference is like night and day. I noted in a post that I had tripped and fell on it with my knee...lol ..nope.. I threw the damn thing and it hit the wall. Yahhh.. I know stupid lol... Something really pi$$ed me off tho and I kinda lost it.. .poooof....... Anyway, I had about 30 cracks in my digitizer and amazingly it still worked. Replaced it two days ago and it works great.
That factory adhesive is some SERIOUS stuff. I have performed many electronics repairs over the years and this...well...removing the digitizer and applying the new strips in exactly the right size was a royal pain in the a**! You REALLY gotta get that digitizer glass HOT if you want to be able to loosen it. Light heating WONT do squat to it. And the new strips arent even half as strong as the factory stuff. You really need patience and precision here.
Yes, dust ISVan issue where I live. Canned air came VERY useful. Also its good to have isopropyl alcohol and soft paper towels so you can clean any smudges you make on the LCD before reapplying the digitizer glass. Basically it's best to blow air over it quickly as you press the digi down to the adhesive. That makes sure every bit of contaminant is out.
About the ribbon cables, no I didn't reapply the amber tape to the jawbone connectors. Much of their adhesiveness was lost when I pulled them off. And as long as the ribbon cables are seated in properly and the jawbone connectors are securely locked down, they wont come disconnected. The tape is only there as an additional measure to secure the jawbone connectors from unlocking. Unless you drop your phone on concrete a lot, those cables arent coming loose....even then, dropping it wouldnt knock those loose.. Its more secure than you think. As far as the phone NOT working, the orange tape would have NO effect on that. Maybe one of your cables were partially disconnected and shorted out something on the mainboard. Either that, or it is static sensitive. Its possible if anything is CMOS.
ONLY issue I have since the repair is the top of the digitizer keeps pushing up because of the digitizer ribbon cable and where you have to bend and fold it in that groove to guide it behind the LCD . The ribbon isnt pinching down well and acts as a spring on the digitizer glass....adhesive not doing anything for that.
oh, did you all remove and reapply the clear (4 button tabs) at the bottom to the new glass? got mine in (the lights are pink now ...weeee ) Had to use some Gorilla super glue to restick them. That adhesive at the bottom was super strong and somehow they lost their stickiness when I pulled them off.
Digitizer after I finally got it unstuck from the LCD... wheewww damn. Lots of cracks. Thats what happens when the phone face eats the wall.....
So, my 4 soft keys on the bottom have yet out. Would fixing the digitzer get them back to working? My screens just got cracked like 2 days ago too, and I just want to make sure before i do all this and then find out i gotta take it all apart again. Thanks in Advance!
UPDATE: So, the digitizer I bought developed a massive dead zone. I already contacted the amazon store I bought it from, they're replacing it for me. Why does this matter? Because now I get to update this post with pictures/video! So, yeah, I guess this guide should get a lot more helpful soon.
Update 2: Ok, so, I don't even know how to express my anger and frustration. This girl at work shoved my phone out of my hands and into the leg of a table, completely destroying my phone. So, yeah, sorry, I guess I won't be updating with pictures/video, because the amazon store isn't going to take the screen back now.
Yo, guys. If anyone noticed that I was gone, I'm flattered, since I don't post a lot. But yeah, I havent had my Optimus G in about a month, so I havent been on this forum. In that time, I went through my Second Motorola Atrix HD, a broken Galaxy S3, and even lived through Google Voice on my computer. It's an extremely long story, and kind of ridiculous, so I'll spare the details.
HOWEVER, I did finally just buy a replacement Digitizer and LCD screen, and successfully installed it, and I want to share tips for anyone doing it themselves.
When removing the back, after you've removed torx screws, start prying the back off from in between where the Sim card and MicroSD go. Where the back of the phone and the chassis of the phone are separate is much more obvious in that cavity, PLUS dents/dings from jamming a screwdriver in there wont be noticeable when you put the bay cover back on.
Don't force anything off. Make sure you've removed every screw, unclipped every clip, and removed ribbons from everything you're trying to take off.
Removing the battery is tricky. Be careful not to deform it too much, cause that's dangerous. But there are 2 strips of double sided tape running horizontally beneath the battery. Try to get something between the top one and the battery, then carefully pull the battery off the second strip with your hands. sticking too much stuff beneath it to pry it up is going to cause some trouble, so lifting it with your fingers might be better.
Remove the motherboard. detatch all the ribbons, antennae, everything, then pull up from the left, then slide left and out. This is how I got it out with the least resistance, but there is no science to it. If you've gotten this far, you can figure out how to pull it out without breaking it in half.
Components that need to be removed before LCD+Digitizer removal:
Motherboard
Battery
Camera
Just put them off to the side, you don't want them damaged during the next part.
WARNING! If you plan on saving your LCD screen, DO NOT DO THIS. The high heat will cook your screen and make it unusable. Only do this to remove a broken or unsavable Digitizer+LCD.
Alright, now pull out the heat gun. Alternatively, you can do what I did, and use a hair dryer. Not even kidding, this will work fine, and will be hilarious when you tell your friends about it.
On a high heat, start heating the screen. If you're using a heat gun, just do your thing, you know how it works. Hair dryer folks, keep the dryer very low to the phone, low enough to feel the dryer being pushed up by the air, holding it just high enough so it sort of hovers. (You'll know what I mean when you try it. If you don't, just keep it about half an inch off the phone.) Move the dryer along the edges of the screen, all the way around, thats where the glue is. It should heat up pretty fast.
Using your pry tool, start at the speaker grill and pry all the way around the phone. lifting just slightly upwards. If it's not extremely easy, apply more heat. Work all the way around, then pull the screen off. Be careful, it's likely you'll shatter the screen even more at this part if you're not careful. User Bozwell had an excellent suggestion (post 4), cover your screen in tape, then begin separating the screen to keep from getting glass everywhere. Great idea, Boz!
Alright, so from here on out, it's just reassembling your phone correctly. Piece o cake.
Firstly, put your new screen in. If it came with adhesive, it's up to you if you want to apply it now. I'd think you probably have to, but up to you.
If you're like me, and no adhesive was provided, hold off on doing anything for now. Just put the screen in the hole, and thread the ribbons through.
The motherboard lines up with some contacts on the chassis in a few places, but most importantly, there is a connection on the top left corner of the body, and the UNDERSIDE of the motherboard that needs to be made. I believe it's proximity sensor, but not sure. It's very difficult to tell if its attached, but look at what I'm describing, and try your best to mate them.
Don't forget ANY cables. Like, that's pretty obvious, but even when you're sure you didnt forget any, check again. The camera's ribbon is underneath the screen's, don't forget that one. I reassebled the whole thing, everything was working perfectly, except I no longer had any mobile connection. I couldn't imagine what I'd broken, since that's a whole different area, but going to phone status and checking my signal strength revealed I forgot to reconnect the white antennae (status showed my signal at -200,000 dbm). So, double check, because the more often you have to reopen your phone, the more flimsy it's going to get.
Alright, screw the plastic shielding back on, reconnect your battery, then flip the phone to be face up. Power it on, test the screen to make sure it's functional. If all is well, power off and glue the screen in. What I did, and I welcome anyone to tell me a better glue type or method, is plain ol Super glue along all the edges where the old glue was. Press it in, flip it over, and while it's drying, finish reassembling the phone (should just be make sure everything is screwed in inside, then put back glass back on.
If your screen wasn't functional, I guess try to get it replaced by whoever you bought it from, and leave your phone disassembled for when it gets to your house.
Alright, that's pretty much the thick and thin of it, it genuinely isn't that hard of a replacement. I've done a number of digitizer/lcd replacements, not bad at all. I hope this helped anyone stuck or wondering about anything. This video can be used as a rough example, but it goes really fast.
Good Luck!
replacement of lcd/digitzer
the removal was a nightmare for me. It was hilarious when the glass cracked it was exploding into a million little bitty pieces. I didnt use much heat, and there lied my problem. But yeah mine cracked in a way that it was completely unresponsive.
gruiz3 said:
the removal was a nightmare for me. It was hilarious when the glass cracked it was exploding into a million little bitty pieces. I didnt use much heat, and there lied my problem. But yeah mine cracked in a way that it was completely unresponsive.
Click to expand...
Click to collapse
Haha that's crazy, it bothers me how fragile this phone seems to be.
To keep the glass shards from going everywhere try covering the screen in tape before you start.
bozwell said:
To keep the glass shards from going everywhere try covering the screen in tape before you start.
Click to expand...
Click to collapse
Great idea, OP updated!
So, what would I do if the screen itself is ok and it's just the glass (and digitizer) that is broken?
MoFoQ said:
So, what would I do if the screen itself is ok and it's just the glass (and digitizer) that is broken?
Click to expand...
Click to collapse
You'll need a real heat gun, I think. You'll have to find a heat just hot enough to soften the glue, but not cook your lcd. Hair dryer method might work if you are extremely careful and very quick, but not sure exactly what the best method would be. Sorry
ripin150 said:
You'll need a real heat gun, I think. You'll have to find a heat just hot enough to soften the glue, but not cook your lcd. Hair dryer method might work if you are extremely careful and very quick, but not sure exactly what the best method would be. Sorry
Click to expand...
Click to collapse
I figured...though I've been eye-ing using the screen+digitizer+front housing if and when they get back into stock.
(digitizer only is also out-of-stock)
Hello,
Something happened to my watch. I opened it to install an SD card. I did as the instructions says, carefully. The rubber gasket was well placed and I tightened the screws the maximum I could, with the provided screwdriver. I guess it would not be tight at all, because, although it has been wet three times and anything happened, Yesterday it was exposed to sweat for a while, and then washed the same way like previous times. Today it worked well all the morning, but around noon, I saw it appeared many stripes on the screen and checking the clock externally I've finally seen condensation into the lens, so I guess, obviously, that moisture has entered inside the watch. I've opened the watch, remove battery and SD card, and then introduced it into rice, using an airtight container to try drying it.
Lens condensation has disappeared, but in the display is still appearing lines.
I wonder what can I do, who should I contact for assistance to repair, where should I send it for repair in case I can't revive the screen, because as I think, this type of damage is not covered by warranty.
I am disappointed with this device because of this. It should not be so complicated to close it and to keep it well sealed. Its design in this particular point is disastrous. I can ensure that the rubber seal was installed properly, and the only thing I can imagine is that the screws do not stay tight properly, but I repeat that I tightened it all the way I could, strongly, until the limit of not to damage the screw heads, and checking for the joints are well sealed. If I finally can fix the watch, the next time I need to open the back cover, I'll pre-tighten it with a sergeant tool before tightening the screws... it seems to be necessary...
Thank you for your help.
It is ruined. Sell it for parts maybe. A shame.
Sent from my Nexus 5 using Tapatalk
lanzas said:
If I finally can fix the watch, the next time I need to open the back cover, I'll pre-tighten it with a sergeant tool before tightening the screws... it seems to be necessary...
Click to expand...
Click to collapse
This is a waste of time. There is no way to make the existing case waterproof - not just the two screw openings but also the antenna, speaker, microphone and buttons are all possible routes for moisture ingress.
One look at the SIM cover and its pretend gasket convinced me of this. There is not enough structural integrity to ensure a good seal. The gasket will not be compressed in a way that makes a watertight seal - over tightening might even make things worse by deforming the plastic.
If you ever get it to work again, keep it dry.
lanzas said:
Yesterday it was exposed to sweat for a while, and then washed the same way like previous times.
Click to expand...
Click to collapse
It's not a very good idea to wash an electronic device that has no water / moisture protection what so ever (the seals don't do much good, and there are lots of other gaps in the watch where water can get in). Sometimes devices can recover when dried completely. Maybe put it in a bag of rice, that's great for absorbing moisture... But most likely, it's dead.
It is supposed to be a waterproof watch...
Definitely the screen is broken. The watch works fine, but the screen shows a lot of lines that don't allow clear visualization. No one from Omate answered my email...
I feel cheated... and silly...
You WERE cheated, we all were. Don't feel silly though, you were misled by a pro.
You might possibly be able to replace the display with an iPod Nano display, but I don't know anyone who has and an iPod Nano display might be worth more than your TrueSmart.
Sent from my Nexus 5 using Tapatalk
First off i'm not really sure where to post this because there is no durability section in real life reviews and i think this is more of a discussion than a question.
So what do you think of the durability? After watching this video i realized that this phone can benefit a lot from a case, since: the flash and color spectrum cover is plastic, the camera sticks out and the aluminum seems to be painted (at least in the pink version).
The aim of the thread would be to share experiences, findings (like exactly what kind of aluminium is used and is it painted or naturally colored) and maybe even guides that are durability related (like removing scratches).
As i inspected my phone i noticed a lot of hairline scratches on the back, after only one week of use, luckily they are only visible from certain angles in good lighting. They don't rub off (like htc or iphone back scratches). My first reaction was to maybe try toothpaste, but i think i'll hold off as of now. If i end up trying anything i'll add it to this thread.
Dropped my xz1c accidently today down the spiral stairs from 3m descending slowly 20cm/steps 5 times then after 2m mark hit mirror glass wall in front and straigh fall straight to granite floor, microsd tray came out by 5mm, above the sdcard / sim card tray near screen plastic chip off, under the left corner there is a serious bending slightly upward, can see some opening under the bright light, likely not water tight anymore, but pressure sensor test says it is still water tight, not willing to risk it though.
Andrew0811 said:
Dropped my xz1c accidently today down the spiral stairs from 3m descending slowly 20cm/steps 5 times then after 2m mark hit mirror glass wall in front and straigh fall straight to granite floor, microsd tray came out by 5mm, above the sdcard / sim card tray near screen plastic chip off, under the left corner there is a serious bending slightly upward, can see some opening under the bright light, likely not water tight anymore, but pressure sensor test says it is still water tight, not willing to risk it though.
Click to expand...
Click to collapse
Where can i access the pressure sensor test? I couldn't find it in the support app among the other tests.
Must use default sony dialer as default app then *#*#service#*#* or *#*#7378423#*#* somewhere inside, is not using default sony dialer now, ask again if can't find.