Related
So i installed my skinomi screen protector since my other one was scratched and got water under the screen somehow.. Thought it would dry up but it's pretty bad and it's been 24 hours now.. Also there seems to be something wrong and the bottom right of the screen has brighter light coming through in lines. What do i need to replace if i ever choose to get a new screen, a digitizer? I'm not sure what to buy to fix this and any suggestions on where to get a good one. I know the ones on ebay are cheap but i'm afraid they might be bad or something. Any help would be great as this could have been avoided if i didn't use too much solution. Only if i could go back in time....
Try using a blow dryer on low heat near the screen.
I did that, i think i did everything possible. The grey spots probably don't worry me as much because i have a feeling they'll dry out but what's worrying me is the screen seemed to have white lines that are getting bigger and spreading a bit. It's not completely white but it's a lot brighter than other areas. I had to bite the bullet today and use it because of emergency or else i would have let it dry for a few days. I'll take a picture tomorrow afternoon to show what it looks like.
If someone can help i'm planning to open it up and try to clean the screen but if it doesn't get cleaned all the way what would i need to buy to replace it, the LCD screen or a digitizer? I was thinking the LCD because the digitizer is mostly just a glass screen that usually doesn't need replacing unless it's cracked right?
Right, but there's a pretty decent chance you'll crack the digitizer when removing it from the LCD, so you may as well order the complete assembly...should be around $45.
Well i forgot to take a picture today but i'll take one tomorrow of the before and after. I'm receiving my pry and screwdriver set tomorrow and i'll try to clean it before trying to replace this. I'll report how it goes.
uEih said:
Well i forgot to take a picture today but i'll take one tomorrow of the before and after. I'm receiving my pry and screwdriver set tomorrow and i'll try to clean it before trying to replace this. I'll report how it goes.
Click to expand...
Click to collapse
You'll have to be very careful. I was and I still screwed the digitizer trying to clean out some water I had under mine. I ended up having to order a new lcd+digitizer combo.
yareally said:
You'll have to be very careful. I was and I still screwed the digitizer trying to clean out some water I had under mine. I ended up having to order a new lcd+digitizer combo.
Click to expand...
Click to collapse
Yea i did it and was very careful, it wasn't perfect but i didn't crack it or anything, just a little part on the corner that seemed to peel the adhesive off from the digitizer so it looks a bit ugly there. The LCD is completely clean and i cleaned under the digitizer and turned the phone back on but unfortunately it wasn't water in between the digitizer and LCD, the water seemed to be in the LCD so i just went ahead and ordered a new digitizer + LCD combo so they'll be easier to install as a whole than separate.
Apart from all that the screen seemed to have gotten more grey covered on it. I'm not sure if the grey spots are the water marks or the brighter spots because as time passes there are more grey spots covering the screen. Not like it matters anymore.
Also i bought the digitizer + LCD from ebay from hong kong cause it's the cheapest and i feel as if they're manufactured there anyways so there shouldn't be a problem in quality?
Sucks that it had to end up like this, i've never had problems installing wet protectors but i think i'm staying far away from them now...
Okay so I am sharing my experience for everyone. I had recently broken my screen, and I needed to replace the screen. I bought a screen digitizer off of eBay, and....Destroyed the phone sub frame. The reason I am posting is because I am warning all of you, you need to buy a full display assembly online. This includes the whole new display( glass and LCD) wires and bits, and a full subframe. Unless you are superior to an Asian 12 year old working in the factory that made your phone (hint hint, wink wink, you're not) than you need to buy a full assembly, or end up like me an destroy your phone.
Sent from my Amazon Kindle Fire HD using Tapatalk HD
+1.
Unfortunately, I saw this post after doing damage to my phone. The plastic housing that the digitizer /lcd sits in is verrrryyy easy to damage around the edges when you try to separate the screen. Heating it with the heat gun to get the separation actually makes it even more fragile and prone to damage. Thankfully I was able to return digitizer/lcd and get full setup from here :
http://www.etradesupply.com/oem-htc-evo-4g-lte-lcd-screen-and-digitizer-assembly-with-front-housing-and-light-guide.html
Hopefully things will go a little better this time.
Wow, that includes the plastic frame? I replaced my screen a couple of weeks ago (glass and LCD), and the edges of the frame did get slightly chewed up. It's not too bad, but I wish I had known abut this item.
On a positive note, I suppose I can get a job in China when the economy completely collapses.
Sent from my Nexus 7 using xda app-developers app
Ya my screen got waterlogged after I got trashed and left it out in the rain. Let everything dry out and thankfully all the boards and connectors work. I ended up going the cheap route and just buying a screen and not the frame. I almost successfully got the thing apart. I do have a small chip in the frame on the left side but my case covers that. I only paid around $50 but I did give myself around $50 in headaches. Definitely spend the extra $50 and just get the whole package.
If you do decide to try and separate the screen from the frame, use a lot of heat. Not necessarily high heat, but for a good duration. Get the adhesive nice and warm. Then pry it loose through one of the holes in the housing/frame (go at it from the back) and slowly work it away from the frame. Once you get it off, heat the adhesive back up and then add some 5 minute quick epoxy to the black adhesive pads in the frame. Then use some clamps and let the epoxy cure. There is a great video I followed below. It took me a while and I will probably ride with this for a minute until it bothers the hell out of me. My gf said she can't even notice.
https://www.youtube.com/watch?v=Ae52Ug8vFwA
case screen cover plastic sheet work?
I'm just wondering how many naked phones get broke compared to well protected?
Gnexd said:
I'm just wondering how many naked phones get broke compared to well protected?
Click to expand...
Click to collapse
I have a Incipio NGP case on mine all the time and I always have a screen protector installed (usually the cheap ones from Amazon). I have never had a problem with the screen until I left my phone out in the rain. The Gorilla Glass II is decently strong but only to a certain extent. I mainly use the screen protector from scratches if I accidentally put it in the same pocket as my keys.
I was afraid of breaking mine one day, fortunately for me my volume button went out first and I have Best Buys insurance and the replace the phone with no deductible.
Seems like screen issues are pretty common on this model. I'm on my 4th Evo now because the screen kept failing on me. Based on what I read it sounds like I'd never want to have to replace this myself.
I got my pebble blue GS3 a week ago. It was used, but in pristine condition, with a scratch-less back and front. Since day one, I've been using a rubber back protector for the phone, which covers the back as well as the sides completely.
Today, I dropped my phone from pocket height on the floor, and picking it up I didn't notice any scratches or cracks and the phone worked perfectly fine. The phone was in the back protector as always, so I didnt think any thing of it and put it back in my pocket.
A few hours later, sitting on my laptop, I picked up my phone to make a call and noticed the golden colored discoloration in the bottom right corner of the phone (see attached pictures). I assume this was the corner on which the phone was dropped.
The discoloration appear to be air bubbles, stuck inside the screen. When I press the corner of the bubble, it shifts slightly and changes shape as air bubbles under screen protectors do. When I press it really hard, the golden starts disappearing and becomes blue just like the rest of the phone. The screen and touch works completely perfectly, and there is absolutely no difference in the quality of the AMOLED. From this, I assumed that the digitizer is fine, but I cant for the life of me figure out how these bubbles formed and why they wont go away
I searched for hours, but couldn't find a single post with the same problem. I would love to hear some ideas to try and get rid of this discoloration. I've barely had this phone for a week, and seeing it ruined already makes me sad
If it cant be fixed, I guess the final solution would be to get the front glass replaced. But before that, I would like to try any and all suggestions that you guys might want to throw my way
The glass is glued to the digitizer whit some sort of gel.
Your glass has come off the digitizer and form air bubbles.
The only way to restore it is change the glass and digitizer.
Maybe a really tight case can solve it when it pushes the glass to the digitizer.
verzonden met de xda premium app.
coolhof said:
The glass is glued to the digitizer whit some sort of gel.
Your glass has come off the digitizer and form air bubbles.
The only way to restore it is change the glass and digitizer.
Maybe a really tight case can solve it when it pushes the glass to the digitizer.
Click to expand...
Click to collapse
I was planning on getting a heat gun somehow, and heat the corner at 180F. It is said its the temperature at which the gel between the front glass and the digtizer melts or something, and becomes easy to seperate.
Do you think this would work? There is just a golden colored bubble, and it isnt affecting the working of the digitizer in any way. It is just next to the back button, and the button works absolutely perfectly.
Still waiting for any more suggestions on how to fix this Would also appreciate if someone could link me to someone with the same problem as this. I swear I've searched for hours and didnt find anything.. I can't be the only one in the world
The golden color is the top film from the digitizer.
So I don't think a heat gun is doing the job.
You can try but be very careful not to damage it more.
Wish you good luck.
Verzonden vanuit Nederland naar de rest van de wereld met de xda premium app.
bilalali said:
Still waiting for any more suggestions on how to fix this Would also appreciate if someone could link me to someone with the same problem as this. I swear I've searched for hours and didnt find anything.. I can't be the only one in the world
Click to expand...
Click to collapse
You are not alone. My S4 have the same issue, and the screen bezel is thiner than the S3... Started a couple weeks ago just after a visit to the carrier tech support, was there for unknow poor signal issue, solved by a SIM replacement and reprogramming. I know they dropped on the floor or on a work table/desk it as is "naked" without the protective case... Came back after a couple of days when I noticed the "stain" on right bottom corner and they said they handle the devices careful also have rubber pads on floor and tables to protect in the event of an "accidental drop"... So they will not replace for free, only via insurance and I have to pay a difference $$$
Anyhow, after that I dropped it so bad on rough concret right on that corner, protective case do they work but I think that corner took a good shock... I do massage the spot and it gone away for a couple of days then come back. I don't k know if temperature changes affect as it could be moisture from condesation penetrating the thin edge between bezel and screen...
I will try different cases to see if it can mask the damage until I can afford the insurance diference $ then will replace or maybe upgrade my phone...
Well I did one last week that was successful but I was practicing on one with a broken digitizer so it was no good anyway. I broke it. This one seemed more hard to separate from the lcd. I don't know why. The lcd lifted from the housing and I didnt use much heat at all. But I'll post pictures for anyone who would like to attempt this. You can see on the pic with the tool how thin the glass is and where the lcd lifted from the housing.
Sent from my SCH-I545 using xda app-developers app
Oh yea.you have to be extra careful of that flex cable connecting to the lcd which is exposed
Sent from my SCH-I545 using xda app-developers app
warriorpluto said:
Well I did one last week that was successful but I was practicing on one with a broken digitizer so it was no good anyway. I broke it. This one seemed more hard to separate from the lcd. I don't know why. The lcd lifted from the housing and I didnt use much heat at all. But I'll post pictures for anyone who would like to attempt this. You can see on the pic with the tool how thin the glass is and where the lcd lifted from the housing.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
I was looking for a thread to post this in, this may be the right place as you may have an idea, since you just installed a mega screen.
I cracked my mega screen last night, originally the phone was still working. In about half an hour the screen wasn't registering swipes, so I can't even unlock the screen. I dropped the phone in the rain so I'm not sure if it's simply the screen or if water has gotten in to the cracks?
Anyways, I am trying to make a decision on wether to sell my broken phone to Mazuma mobile and get around $120 back, or wether it's worth trying to get fixed. I'm not confident fixing phones, so ordering in the screen and attempting it is not an option. What I want to know, is what are the chances of a local repair shop being able to source a mega screen, and fix it, for a decent cost that would make getting it fixed the better option? Since you have just installed a screen I figure you at least know how much the part is
You can buy the lcd screen + digitizer which comes all pre-assembled and all you have to do it swap the whole screen + digitizer out as one unit..this way no fear of breaking anything..i see one on ebay for $158.00 US for the mega 6.3 i9200..but i think it will also work on the other 6.3 mega models..as they must all be the same that way...but i am not 100% sure on that. :good:
leetrevor81 said:
I was looking for a thread to post this in, this may be the right place as you may have an idea, since you just installed a mega screen.
I cracked my mega screen last night, originally the phone was still working. In about half an hour the screen wasn't registering swipes, so I can't even unlock the screen. I dropped the phone in the rain so I'm not sure if it's simply the screen or if water has gotten in to the cracks?
Anyways, I am trying to make a decision on wether to sell my broken phone to Mazuma mobile and get around $120 back, or wether it's worth trying to get fixed. I'm not confident fixing phones, so ordering in the screen and attempting it is not an option. What I want to know, is what are the chances of a local repair shop being able to source a mega screen, and fix it, for a decent cost that would make getting it fixed the better option? Since you have just installed a screen I figure you at least know how much the part is
Click to expand...
Click to collapse
If you get the lcd and digitizer together, you can fix yourself and it's easy just as star master says. If you have a shop nearby they can replace just the glass
Sent from my SCH-I545 using xda app-developers app
leetrevor81 said:
I was looking for a thread to post this in, this may be the right place as you may have an idea, since you just installed a mega screen.
I cracked my mega screen last night, originally the phone was still working. In about half an hour the screen wasn't registering swipes, so I can't even unlock the screen. I dropped the phone in the rain so I'm not sure if it's simply the screen or if water has gotten in to the cracks?
Anyways, I am trying to make a decision on wether to sell my broken phone to Mazuma mobile and get around $120 back, or wether it's worth trying to get fixed. I'm not confident fixing phones, so ordering in the screen and attempting it is not an option. What I want to know, is what are the chances of a local repair shop being able to source a mega screen, and fix it, for a decent cost that would make getting it fixed the better option? Since you have just installed a screen I figure you at least know how much the part is
Click to expand...
Click to collapse
And don't sell. $120 is a freaking rip off
Sent from my SCH-I545 using xda app-developers app
warriorpluto said:
And don't sell. $120 is a freaking rip off
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
How much do you think it would go for on ebay? (or somewhere else) I didn't think a damaged phone would be worth selling?
That phone is still with over $200 as is.just the good motherboard alone. Especially if it had a clean imei number..then counting other parts of the phone too
Sent from my SCH-I545 using xda app-developers app
Good tutorial how to fix it
There is some kind of double side transparent adhesive between LCD and digitizer. So good luck
Opened front glass
Hi, I opened front glass of Mega 5.8 to clean the dust inside it. When I put it back, the touch is not working. Earlier it was working perfectly, I did not remove any cables. Also that I cleaned it with dry cloth while the phone was on.
What may be the issue?
warriorpluto said:
Oh yea.you have to be extra careful of that flex cable connecting to the lcd which is exposed
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
How does it separate?
warriorpluto said:
Well I did one last week that was successful but I was practicing on one with a broken digitizer so it was no good anyway. I broke it. This one seemed more hard to separate from the lcd. I don't know why. The lcd lifted from the housing and I didnt use much heat at all. But I'll post pictures for anyone who would like to attempt this. You can see on the pic with the tool how thin the glass is and where the lcd lifted from the housing.
Sent from my SCH-I545 using xda app-developers app
Click to expand...
Click to collapse
Hi,
I've never worked on one of these before but I have repaired many GS3, GS4, Note 2 with no problems. You successfully repaired one so my question is, is the optical adhesive like the GS3 where it rubs off with your finger? I've noticed a difference in GS3 & GS4 adhesive the GS4 is more difficult to clean off digitizer.
That yellow flex cable in your pic looks like a Digitizer flex. The layers are LCD (bottom) / Digitizer (sits on top of LCD so center) / Glass (top which is what our finger touches).
I have a Mega coming in tomorrow and the customer bought just the glass online. I'll see if I can separate. If you have any questions let me know I have repaired many a phones.
Did you get it?
ReyesARG said:
Hi,
I've never worked on one of these before but I have repaired many GS3, GS4, Note 2 with no problems. You successfully repaired one so my question is, is the optical adhesive like the GS3 where it rubs off with your finger? I've noticed a difference in GS3 & GS4 adhesive the GS4 is more difficult to clean off digitizer.
That yellow flex cable in your pic looks like a Digitizer flex. The layers are LCD (bottom) / Digitizer (sits on top of LCD so center) / Glass (top which is what our finger touches).
I have a Mega coming in tomorrow and the customer bought just the glass online. I'll see if I can separate. If you have any questions let me know I have repaired many a phones.
Click to expand...
Click to collapse
I wonder how was it going with your repair?
http://www.witrigs.com/samsung-galaxy-mega-replacement-parts
Adhesive is a problem
letus1 said:
I wonder how was it going with your repair?
Click to expand...
Click to collapse
Hey,
No good. The LCD was lifting off the frame which is a guarantee to break on such a large device. Also the adhesive is not the same as the GS3, it doesn't separate as easy. I stopped after I noticed the optical adhesive was not the same so do not attempt to "Lift Separate"
The best way to remove this digitizer is with a hot plate & (.10mm) molybdenum wire and slowly drag the wire between the LCD & Digi while face down on hotplate.
ReyesARG said:
Hey,
No good. The LCD was lifting off the frame which is a guarantee to break on such a large device. Also the adhesive is not the same as the GS3, it doesn't separate as easy. I stopped after I noticed the optical adhesive was not the same so do not attempt to "Lift Separate"
The best way to remove this digitizer is with a hot plate & (.10mm) molybdenum wire and slowly drag the wire between the LCD & Digi while face down on hotplate.
Click to expand...
Click to collapse
If i separated the digitizer and the glass ftom the lcd, than can i bound the new one with LOCA or will that damage the LCD?
ReyesARG said:
Hey,
No good. The LCD was lifting off the frame which is a guarantee to break on such a large device. Also the adhesive is not the same as the GS3, it doesn't separate as easy. I stopped after I noticed the optical adhesive was not the same so do not attempt to "Lift Separate"
The best way to remove this digitizer is with a hot plate & (.10mm) molybdenum wire and slowly drag the wire between the LCD & Digi while face down on hotplate.
Click to expand...
Click to collapse
I knew that was the only way to do it, with hot plate and fishing pole string. I'm sure it's a slow process. I'll have to invest in a good hot plate.
Sent from my SM-N900V using xda app-developers app
No huge investment needed, I use a standard electric pancake griddle which can be bought for around $20. Good, even heat. I've never tried the fishing line method but a pair of business cards does the job very well. I get it started with a dull razor blade in the corner and as soon as I see the glass separating, I slide a business card in behind it. Do the same for the other side. On these big screens, slide the cards down a bit, lay it down on heat, repeat. The trick to not busting the LCD is to keep the heat on it and take your time.
My temperature is set to 200 farenheit. Not sure off hand what that converts to in celsius. Ideally, you don't want the surface to pass 120 celsius. If in doubt, start low and increase temp slowly until the glue softens enough.
The glue we're taking about is LOCA[liquid optically clear adhesive] and is UV activated. It can be bought online pretty cheap. If you're going to replace the glass, go ahead and use the LOCA when putting the new glass on. I've seen sensitivity issues on glass that doesn't have the glue between it and the LCD. If you use the glue be sure to remove EVERYTHING from the frame including cameras, speakers, buttons and mics as it can get messy and go pretty much everywhere. To activate the glue you can literally take it outside on a sunny day and it will cure fairly quickly, about 5 mins or so. To remove it from unwanted areas just use a toothpick, toothbrush, and some rubbing alcohol. I've done it dozens of times this way and it always comes out looking factory fresh
VirtueToVice said:
No huge investment needed, I use a standard electric pancake griddle which can be bought for around $20. Good, even heat. I've never tried the fishing line method but a pair of business cards does the job very well. I get it started with a dull razor blade in the corner and as soon as I see the glass separating, I slide a business card in behind it. Do the same for the other side. On these big screens, slide the cards down a bit, lay it down on heat, repeat. The trick to not busting the LCD is to keep the heat on it and take your time.
My temperature is set to 200 farenheit. Not sure off hand what that converts to in celsius. Ideally, you don't want the surface to pass 120 celsius. If in doubt, start low and increase temp slowly until the glue softens enough.
The glue we're taking about is LOCA[liquid optically clear adhesive] and is UV activated. It can be bought online pretty cheap. If you're going to replace the glass, go ahead and use the LOCA when putting the new glass on. I've seen sensitivity issues on glass that doesn't have the glue between it and the LCD. If you use the glue be sure to remove EVERYTHING from the frame including cameras, speakers, buttons and mics as it can get messy and go pretty much everywhere. To activate the glue you can literally take it outside on a sunny day and it will cure fairly quickly, about 5 mins or so. To remove it from unwanted areas just use a toothpick, toothbrush, and some rubbing alcohol. I've done it dozens of times this way and it always comes out looking factory fresh
Click to expand...
Click to collapse
What kind of griddle? This is the one without the edges right?
Sent from my SM-N900V using xda app-developers app
starmaster10 said:
You can buy the lcd screen + digitizer which comes all pre-assembled and all you have to do it swap the whole screen + digitizer out as one unit..this way no fear of breaking anything..i see one on ebay for $158.00 US for the mega 6.3 i9200..but i think it will also work on the other 6.3 mega models..as they must all be the same that way...but i am not 100% sure on that. :good:
Click to expand...
Click to collapse
I like this..
fixxforyou said:
May i ask how much for this glass?
Click to expand...
Click to collapse
Who give your answer ? Mention it..
Dropped z2 yday ;/ it was one of my frenchies who jumped on me, phone fall first on screen, than on back glass and finaly landed in dogs water bowl. took it out right away, screen ok, back glass broken and no visible sign of any water entered.
I want to replace the broken glass deck, but to make it so that phone will still be wateproof.. Anyone have any experiance with that? If so, where did you order back glass and did it come with adhesive coating ..?
Thanks for all answers!
102
aawawa said:
Dropped z2 yday ;/ it was one of my frenchies who jumped on me, phone fall first on screen, than on back glass and finaly landed in dogs water bowl. took it out right away, screen ok, back glass broken and no visible sign of any water entered.
I want to replace the broken glass deck, but to make it so that phone will still be wateproof.. Anyone have any experiance with that? If so, where did you order back glass and did it come with adhesive coating ..?
Thanks for all answers!
Click to expand...
Click to collapse
I got mine off of eBay. You need the back glass and new adhesive.
Phone won't be as waterproof anymore, but I've dipped my phone in the sink fora few seconds without harm.
http://iphoneno.com/categories/Sony-Mobile-Part/Xperia-Z2-Parts/
mariosraptor said:
http://iphoneno.com/categories/Sony-Mobile-Part/Xperia-Z2-Parts/
Click to expand...
Click to collapse
Does this come with adhesive and would you know how if we can retain nfc? I heard changing the back you lose NFC...
Thanks.
It comes with adhesive. But nfc antenna must be unglued from the old back glass. To do that you have to heat up the glass very well so it won't break or torn off.
Heat up the old glass i mean.
hey guys , did anyone succeeded to buy original back glass , and after that phone is again waterproof ? cos some people told me that doesnt matter what back cover i buy even with adhesive , the phone wont be waterproof , only sony can repair it for waterproof again. is that true ?
No man
There are adhesive on the back of glass dont mention about it
You could either buy the plate AND the adhesive thingy (comes separately). Or go my way (slightly risky).
The stock glass plate keeps breaking so I took the measurements and made an Aluminium plate. Then drilled camera holes into it and painted it. Then came the tricky part. I stuck the plate into place using regular epoxy (waterproof) adhesive. You have to be very careful while doing the last part because of obvious reasons tho.
The problem with the adhesive thingy that you get to buy (And also the one that Sony uses in the device) is that although its water proof, it isn't heat resistant. and as we all know how Sony phones heat, the adhesive comes off.
MindfreakBS said:
You could either buy the plate AND the adhesive thingy (comes separately). Or go my way (slightly risky).
The stock glass plate keeps breaking so I took the measurements and made an Aluminium plate. Then drilled camera holes into it and painted it. Then came the tricky part. I stuck the plate into place using regular epoxy (waterproof) adhesive. You have to be very careful while doing the last part because of obvious reasons tho.
The problem with the adhesive thingy that you get to buy (And also the one that Sony uses in the device) is that although its water proof, it isn't heat resistant. and as we all know how Sony phones heat, the adhesive comes off.
Click to expand...
Click to collapse
This is very creative and I sure as hell would like to try my hand at it. How thick was the aluminum?
I bet your phone becomes hot as an iron when gaming haha, which is good for your internals because of better heat dissipation. Any adverse effects on mobile reception? wifi? bluetooth? guess NFC is gone haha
ice_lander said:
hey guys , did anyone succeeded to buy original back glass , and after that phone is again waterproof ? cos some people told me that doesnt matter what back cover i buy even with adhesive , the phone wont be waterproof , only sony can repair it for waterproof again. is that true ?
Click to expand...
Click to collapse
Well, I given my z2 to friend to replace battery and few days ago I left my phone in silk for 10 minutes, because it was dirty and no issue here.
@MindfreakBS
What are NFC and Cell reception like since installing the aluminium back plate?
Any deterioration in signal strength / call quality / WiFi / Bluetooth?
Pixelado said:
This is very creative and I sure as hell would like to try my hand at it. How thick was the aluminum?
I bet your phone becomes hot as an iron when gaming haha, which is good for your internals because of better heat dissipation. Any adverse effects on mobile reception? wifi? bluetooth? guess NFC is gone haha
Click to expand...
Click to collapse
Aluminium is a millimetre thick. It does get hot, yeah.
Mobile reception is same (Maybe a tad bit lower, idk), wifi bluetooth work fine. NFC still intact. I fixed it onto the plate in position.
@rubiicon59 that should answer your question too
I was planning to post a tutorial. Haven't been able to take out enough time though.
How about a pic...
MindfreakBS said:
Aluminium is a millimetre thick. It does get hot, yeah.
Mobile reception is same (Maybe a tad bit lower, idk), wifi bluetooth work fine. NFC still intact. I fixed it onto the plate in position.
@rubiicon59 that should answer your question too
I was planning to post a tutorial. Haven't been able to take out enough time though.
Click to expand...
Click to collapse
I've asked about the pic for a long time:crying::silly:
MindfreakBS said:
Aluminium is a millimetre thick. It does get hot, yeah.
Mobile reception is same (Maybe a tad bit lower, idk), wifi bluetooth work fine. NFC still intact. I fixed it onto the plate in position.
@rubiicon59 that should answer your question too
I was planning to post a tutorial. Haven't been able to take out enough time though.
Click to expand...
Click to collapse
What if I want to use a 2-mm thick acrylic as my black plate? Is it possible? Because I am afraid that it will exceed the metal frame of the phone and it will ended up looking terrible:crying:
I agree, I think 1.0mm would be more suitable.
At 2mm, you might get an M4 Aqua kind of look hahaha
aawawa said:
Dropped z2 yday ;/ it was one of my frenchies who jumped on me, phone fall first on screen, than on back glass and finaly landed in dogs water bowl. took it out right away, screen ok, back glass broken and no visible sign of any water entered.
I want to replace the broken glass deck, but to make it so that phone will still be wateproof.. Anyone have any experiance with that? If so, where did you order back glass and did it come with adhesive coating ..?
Thanks for all answers!
Click to expand...
Click to collapse
I believe that if the broken glass was the only issue, and you use a original replacement part, or decent adhesive tape to glue them back together, you'll have no problem. I've had the same issue few weeks ago, replaced the screen and the phone didn't experienced any problem when submerged.
Do anyone now where can I get an official or a good quality back glass for my xperia z2, I broke the original one but i don't want to replace with one without any quality.
buy a nice "glue" to fix that..