Screenshot: imgur.com / F9MrUeO
When i press "start" in Tool Studio status is red: Can't find port.
And when i press "Refresh" usb disconnected automaticly, and connect again within ~10 seconds. Please, help.
whitemerry said:
Screenshot: imgur.com / F9MrUeO
When i press "start" in Tool Studio status is red: Can't find port.
And when i press "Refresh" usb disconnected automaticly, and connect again within ~10 seconds. Please, help.
Click to expand...
Click to collapse
Dial *#7678# and tick factory ports and adb
whitemerry said:
Screenshot: imgur.com / F9MrUeO
When i press "start" in Tool Studio status is red: Can't find port.
And when i press "Refresh" usb disconnected automaticly, and connect again within ~10 seconds. Please, help.
Click to expand...
Click to collapse
Anybody want to sell their bricked z17 mini as long as they are in good condition and no hardware component is damaged?
Thx
Related
Hi all.
I received my prestigio pmp 5297c with 4.2 preinstalled. I tried to find a way to root it but without any success.
Any idea would be valuable.
Thanks.
Sent from my PMP5297C_QUAD using xda app-developers app
Rooting problem PMP 5297C QUAD SOLVED
Hi,
I found a solution thanks to this web site:
http://androidforum.cz/viewtopic.php?f=815&t=48237
Translate it with google translate to english. I had some problems installing the right driver on my windows 7 x64 machine but I succeeded.
Basically it goes like this:
1. Download the zip from the link on the web page and unpack it.
2. Start the RKAndroidTool.exe (in the status bar it will say "No found RKAndroid rock usb")
3. Shut down your tablet and disconect the usb cable from the tablet that is connected to your pc.
4. Press the volume up button and hold it for 6 - 7 secconds.
5. Still holding the volume up button plug in the usb cable that is connected to You pc. (At this point in my case nothing happened)
6. (If nothing happens) Go to control panel - device manager and there You will see an unknown device.
7. Right click on the unknown device and select update driver. Point to the folder where You unpacked the downloaded zip / Drivers folder and select the search in subfolders checkbox. press OK button. Windows will install the drivers. After that if the tablet didn't start automatically boot it up by pressing the power button.
8. The RKAndroidTool.exe now will recognize the device.
9. Set the checkbox next to rom/recovery.img and press "RUN"
10. The tool will do what it has to do.
From here on just follow the instructions for rooting the tablet from the website.
Hope it will work for You as it worked for me.
Regards
Just use King root from Play Store
hi..is there anybody can help me...
i got phone model 'ninetology insight' i9430.
it got brick during flash because usb disconnect..it doesn't shows anything...even charging..no display anything..cant turn it on..
hope somebody can help me with this problem..
can you get into bootloader or recovery, or see it via adb?
pavlpavel said:
can you get into bootloader or recovery, or see it via adb?
Click to expand...
Click to collapse
nope..
cant connect to pc either..when i try plug in using usb, nothing happen..
can help me how to connect to pc? thank you
Tab Bricked....Help
I used Swingtel HelloTab 16GB it bricked stuck on Boot LOGO
its CHIP is E720_SIGN & Processor is Qualcomm Powered Intelligent
pleas help me to install CWM & ROM Mathod
its not going to boot recovery MODE
its only BOOT with Vol+ & Power Button in DOWNLOAD MODE and
BOOT into Vol- & power Button in Fastboot Mode
how to Boot into recovery Mode Please HELP
I hope this helps, it happends to me when the 1st-5th time i install the Img file using LiveSuite
try to install USBDeview here the link ->tomsguidedotcom/us/download/USBDeview,0313-13254dothtml
(just retype the dot = "." , can post link here coz im new.
1. open Device Manager and USBDeview
2. click on "Created Date" on upper right of the program
3. uninstall all USB driver the date after the port hud driver (VID_1f3a_PID_efe8) on USBDeview. wait for the Device manager to install the important driver u accidentally uninstall.
4. hold power botton for at least 30 sec
5. run livesuit.exe, select your img file. connect the usb to the PC or laptop
6. while hold volume up insert the usb cable in the andriod device you have.
7. while holding the volume key, press power botton at least 2 sec, 4-5 times.
8.if unknow device show just install manually the usb driver in the livesuit folder using Device Manager (Update DriverSoftware->Browse my 9. Computer for Driver Software-> Let me Pick from the list of device -> Have Disk -> Browse (Go to the LiveSuit Folder click the *.inf driver in usb driver folder) just click ok
9. w8 for the LiveSuit to react. if nothing happend, reapeat Step 4.
10 click on "Created Date" on upper right of USBdeview, check if port hud driver (VID_1f3a_PID_efe8) turn "GREEN" mean conneted . this you click "Yes" on the LiveSuit option given.
Hope This one Help. Good luk!
rkillahph said:
I hope this helps, it happends to me when the 1st-5th time i install the Img file using LiveSuite
try to install USBDeview here the link ->tomsguidedotcom/us/download/USBDeview,0313-13254dothtml
(just retype the dot = "." , can post link here coz im new.
1. open Device Manager and USBDeview
2. click on "Created Date" on upper right of the program
3. uninstall all USB driver the date after the port hud driver (VID_1f3a_PID_efe8) on USBDeview. wait for the Device manager to install the important driver u accidentally uninstall.
4. hold power botton for at least 30 sec
5. run livesuit.exe, select your img file. connect the usb to the PC or laptop
6. while hold volume up insert the usb cable in the andriod device you have.
7. while holding the volume key, press power botton at least 2 sec, 4-5 times.
8.if unknow device show just install manually the usb driver in the livesuit folder using Device Manager (Update DriverSoftware->Browse my 9. Computer for Driver Software-> Let me Pick from the list of device -> Have Disk -> Browse (Go to the LiveSuit Folder click the *.inf driver in usb driver folder) just click ok
9. w8 for the LiveSuit to react. if nothing happend, reapeat Step 4.
10 click on "Created Date" on upper right of USBdeview, check if port hud driver (VID_1f3a_PID_efe8) turn "GREEN" mean conneted . this you click "Yes" on the LiveSuit option given.
Hope This one Help. Good luk!
Click to expand...
Click to collapse
i already try your method..but seems nothing happen...still my android cant connect to pc..
i just only need to connect to pc only..only that way i can solve my problem..thanks anyway..
sigh..
i think because i flash a wrong recovery then my phone brick...
xhitgirlx said:
i think because i flash a wrong recovery then my phone brick...
Click to expand...
Click to collapse
*is there any indication in ur device manager that u are connected wen u plug in the device?
*what usb cable are u using? try using another usb cable with complete pins.
rkillahph said:
*is there any indication in ur device manager that u are connected wen u plug in the device?
*what usb cable are u using? try using another usb cable with complete pins.
Click to expand...
Click to collapse
i try already another usb cable..nothing happen also..i dont know why..
it's like when you plug in your device to the pc nothing happen...
it means no device connected at the pc.
i think no body can help me in this situation..even the developers...thank you.:good:
Hi,
I have received a Lenovo P 780 from Amazon after a long wait which was I guess a Chinese made phone. When I go to Google play I get only Chinese apps & also all system software from Lenovo are in Chinese language I cannot use whats app since it does not recognize my number and also it does detect my current city to show weather update.. I dont want to return this phone as it takes many days to return and get a new phone some one please assist me thanks in advance
Syed Moin said:
Hi,
I have received a Lenovo P 780 from Amazon after a long wait which was I guess a Chinese made phone. When I go to Google play I get only Chinese apps & also all system software from Lenovo are in Chinese language I cannot use whats app since it does not recognize my number and also it does detect my current city to show weather update.. I dont want to return this phone as it takes many days to return and get a new phone some one please assist me thanks in advance
Click to expand...
Click to collapse
Flash a ROW(rest of the world) ROM forom this forum. Your phone will be more understandable.
Sent from my Lenovo P780
stympy said:
Flash a ROW(rest of the world) ROM forom this forum. Your phone will be more understandable.
Sent from my Lenovo P780
Click to expand...
Click to collapse
Perfect can you please give me the steps that I should follow flash the phone with ROW apologies I'm new to these things..
Syed Moin said:
Perfect can you please give me the steps that I should follow flash the phone with ROW apologies I'm new to these things..
Click to expand...
Click to collapse
Ok here it is:
1. download in your computer the drivers
2. install drivers
3. restart your computer (just to be sure) (skip steps 1.2.3 iff you have allready installed drivers)
4. now... turn off your phone
5. plug your USB cable in your computer
6. plug your USB cable in your phone
7. new hardware detected should appear... and should install drivers automaticaly
8. after the drivers are installed unplug your cable from the phone and restart your computer (just to be sure)
9. after restart start flash tool
10. load scatter file from ROM directory(should be target_bin directory)
11. check DA,DL WITH CHECKSUM (NOT OPTIONAL)
12. press Firmware Upgrade button (NOT DOWNLOAD BUTTON)
13. now just now plug usb cable to your phone.
14. firmware flash should start.(some red and other color lines should appear)
15. iff the firmware is not starting remove the case of your phone and hold pressed the little red button for about 20 seconds then release. All this must be done with cable pluged in to your phone.
16. after flash is done a green circle should appear
17. disconect your phone and power on your phone
18. lenovo logo should appear. then you should be pacient because it will took some time before android boots for the first time.
19 Good luck.
stympy said:
Ok here it is:
1. download in your computer the drivers
2. install drivers
3. restart your computer (just to be sure) (skip steps 1.2.3 iff you have allready installed drivers)
4. now... turn off your phone
5. plug your USB cable in your computer
6. plug your USB cable in your phone
7. new hardware detected should appear... and should install drivers automaticaly
8. after the drivers are installed unplug your cable from the phone and restart your computer (just to be sure)
9. after restart start flash tool
10. load scatter file from ROM directory(should be target_bin directory)
11. check DA,DL WITH CHECKSUM (NOT OPTIONAL)
12. press Firmware Upgrade button (NOT DOWNLOAD BUTTON)
13. now just now plug usb cable to your phone.
14. firmware flash should start.(some red and other color lines should appear)
15. iff the firmware is not starting remove the case of your phone and hold pressed the little red button for about 20 seconds then release. All this must be done with cable pluged in to your phone.
16. after flash is done a green circle should appear
17. disconect your phone and power on your phone
18. lenovo logo should appear. then you should be pacient because it will took some time before android boots for the first time.
19 Good luck.
Click to expand...
Click to collapse
Hi,
Thank you so much for your help I tried doing that and step 15 does not complete. The phone is not getting detected I believe I installing MTK drivers but no luck when phone is connected to system in Device manager it show other devices and MTK driver with an ! mark but with in few seconds it goes off. I tried with many times but enabling all USB options from my phone. I will really appreciate your assistance thanks in advance.
Syed Moin said:
Hi,
Thank you so much for your help I tried doing that and step 15 does not complete. The phone is not getting detected I believe I installing MTK drivers but no luck when phone is connected to system in Device manager it show other devices and MTK driver with an ! mark but with in few seconds it goes off. I tried with many times but enabling all USB options from my phone. I will really appreciate your assistance thanks in advance.
Click to expand...
Click to collapse
I did it thanks to full updating the steps in details:victory:
Syed Moin said:
I did it thanks to full updating the steps in details:victory:
Click to expand...
Click to collapse
Sooo... it is working then..
Glad to help. :laugh:
Hi i just follow the steps
1. Download and install Flashtool on your PC
2. Download the firmware you need (from the list below) and move the .ftf file into the directory C:/Flashtool/firmwares
3. Open Flashtool, click on the lightning symbol ("flash device"), select "Flashmode" and click on "OK"
4. Select the .ftf file of what you downloaded and click on "Flash"
5. Wait for a window to pop up (it may take a few seconds/minutes, just be patient)
6. Now turn off your phone and connect the usb cable to it
7. Push the volume-down button, keep pushing and connect the other end of the usb cable to your PC
8. Once the flashing process has started, you can release the volume button
9. NEVER disconnect the USB cable until it's finished!
http://forum.xda-developers.com/showthread.php?t=2759934
with 17.1.A.2.36
Mexico - TELCEL - 1281-5458 - LINK1, LINK2
i dont know my Customization number: my screen is black if a use bottons it rumble, i try factory reset with sony mobile but the program say there is no software for this devise
tnx
i can take photos but the touchscreen dont answer
i just realice i use a phone firmware, anyone have a tablet firmware can i use or somthing?
saduin said:
i just realice i use a phone firmware, anyone have a tablet firmware can i use or somthing?
Click to expand...
Click to collapse
Try this:
xunus said:
I suggest to use XperiFirm. You can download all the avaliable firmwares.
Click to expand...
Click to collapse
Hi guys,
I bought this BOX TV H96max X3 Amlogic S905X3 but it restarts constantly, I want to upgrade the firmware.
I ask for your help on this topic. Can you please confirm the method to avoid confusion.
Step by step (without giving details for step 1, 7 and 8):
1. Prepare the PC environment, install USB_Burning_Tool_v2.1.7.0 and selecting the ".img" firmware
2. Turn off the box and disconnect the power cable
3. Connect the first end of USB 3.0 male cable to the PC
4. Click "start" on "USB_Burning Tool v2.1.7.0"
5. Reset the box by bringing a toothpick into the AV port and keeping it pressed for 8 - 10 seconds, without the box being connected to power supply or to the male USB 3.0 cable.
6. Connect the other end of the USB 3.0 male cable to the box in USB "2.0" port (really in the 2.0 port???)
7. See the identification of the box and the progress of the process ....
8. click "Stop" when finish
I'm confused at step 5, do I plug in the power when entering the toothpick or the box will be powered by the male USB cable?
Thanks in advance.
difahtic said:
Hi guys,
I bought this BOX TV H96max X3 Amlogic S905X3 but it restarts constantly, I want to upgrade the firmware.
I ask for your help on this topic. Can you please confirm the method to avoid confusion.
Step by step (without giving details for step 1, 7 and 8):
1. Prepare the PC environment, install USB_Burning_Tool_v2.1.7.0 and selecting the ".img" firmware
2. Turn off the box and disconnect the power cable
3. Connect the first end of USB 3.0 male cable to the PC
4. Click "start" on "USB_Burning Tool v2.1.7.0"
5. Reset the box by bringing a toothpick into the AV port and keeping it pressed for 8 - 10 seconds, without the box being connected to power supply or to the male USB 3.0 cable.
6. Connect the other end of the USB 3.0 male cable to the box in USB "2.0" port (really in the 2.0 port???)
7. See the identification of the box and the progress of the process ....
8. click "Stop" when finish
I'm confused at step 5, do I plug in the power when entering the toothpick or the box will be powered by the male USB cable?
Thanks in advance.
Click to expand...
Click to collapse
I don't understand why you had to create a new topic while you posted to the similar topic just below. Anyway.
1. Install the USB Burning Tool. You have to install also the LICENCE directory !!!!!
2. Leave the box bare (nothing connected to it - no power adaptor also)
3. Start the UBT tool and load the img file. Wait until it checks it and then press "START". Connect one end of the cable to a USB port of your PC/Laptop
4. While pressing lightly the reset button in the AV port (i.e. with a toothpick) at the same time insert the other end of the cable to the USB port of your box (preferably NOT the light blue port - NOT the 3.0 USB port of the box).
5. Wait until the tool reaches 100% nad then just disconnect the box
Grand merci ath156
ath156 said:
I don't understand why you had to create a new topic while you posted to the similar topic just below. Anyway.
1. Install the USB Burning Tool. You have to install also the LICENCE directory !!!!!
2. Leave the box bare (nothing connected to it - no power adaptor also)
3. Start the UBT tool and load the img file. Wait until it checks it and then press "START". Connect one end of the cable to a USB port of your PC/Laptop
4. While pressing lightly the reset button in the AV port (i.e. with a toothpick) at the same time insert the other end of the cable to the USB port of your box (preferably NOT the light blue port - NOT the 3.0 USB port of the box).
5. Wait until the tool reaches 100% nad then just disconnect the box
Click to expand...
Click to collapse
Hi ath156,
Yes it is true that I already posted this request in another subject but I wanted it to be in a new more captivating with its title.
Thank you very much for your responsiveness and your concise and very explicit answer. I hope to succeed :good:.