I had flashed cm13 in my moto e and installed superSU. When i open superSU , it asks me to select the method to update the binary. I chose "normal". It failed. And asked me to try again after reboot. That too failed. Due to this issue i am unable to use foldermount . Is there any solution?
haribalaji said:
I had flashed cm13 in my moto e and installed superSU. When i open superSU , it asks me to select the method to update the binary. I chose "normal". It failed. And asked me to try again after reboot. That too failed. Due to this issue i am unable to use foldermount . Is there any solution?
Click to expand...
Click to collapse
Use version 2.65 or 2.67 (BETA) - It will use the system-less install (means it can be uninstalled from the Apps list).
Also when you flash the new nightlies, be sure to flash the SuperSU zip in recovery again, or else the error which u said earlier might crop up again.
NB: Do Not click on update binaries (normal or any other method, because that might cause issues which prevents the device from booting... I know this, because I myself have faced such problems earlier)
Bootloop while flashing superSU update zip
I tried flashing UPDATE-SuperSU-v2.46.zip using TWRP(checked mount-> system)
which made the device in the bootloop. Then i had to restore my backup to unbrick the device. So can you explain step by step how to update su binary?
haribalaji said:
I tried flashing UPDATE-SuperSU-v2.46.zip using TWRP(checked mount-> system)
which made the device in the bootloop. Then i had to restore my backup to unbrick the device. So can you explain step by step how to update su binary?
Click to expand...
Click to collapse
Super SU 2.46 was built only for Lollipop ROMs.
Use SuperSU 2.65 or higher
Steps to install after a clean flash of the ROM:
In the Recovery, flash the SuperSU zip
First the phone will boot incompletely (not for all users though), then will boot normally... don't be afraid
You're done!!!
Steps to be followed while flashing new nightlies:
DON'T update automatically from CM Updater
Download the new zip of CM 13, and go to recovery
Wipe Dalvik/ART Cache and Cache only (Nohting else)
Flash the ROM
Flash the SuperSU zip
You're ready to reboot to the new nightly
Hope this helps
Rohitagni said:
Super SU 2.46 was built only for Lollipop ROMs.
Use SuperSU 2.65 or higher
Steps to install after a clean flash of the ROM:
In the Recovery, flash the SuperSU zip
First the phone will boot incompletely (not for all users though), then will boot normally... don't be afraid
You're done!!!
Steps to be followed while flashing new nightlies:
DON'T update automatically from CM Updater
Download the new zip of CM 13, and go to recovery
Wipe Dalvik/ART Cache and Cache only (Nohting else)
Flash the ROM
You're ready to reboot to the new nightly
Hope this helps
Click to expand...
Click to collapse
I've installed superSU 2.65 from play store. Since you insist i will try flashing the latest version. Should i tick "mount->system" in twrp before flashing?
haribalaji said:
I've installed superSU 2.65 from play store. Since you insist i will try flashing the latest version. Should i tick "mount->system" in twrp before flashing?
Click to expand...
Click to collapse
Don't install from Play Store....
I'm sorry... I forgot to mention that
Always flash the zip.... and u donot need to mount system
Rohitagni said:
Don't install from Play Store....
I'm sorry... I forgot to mention that
Always flash the zip.... and u donot need to mount system
Click to expand...
Click to collapse
Thanks Rohitagni . I will follow your instructions and get back to you after flashing the zip.
Rohitagni said:
Don't install from Play Store....
I'm sorry... I forgot to mention that
Always flash the zip.... and u donot need to mount system
Click to expand...
Click to collapse
Wow.. I followed your instructions and it worked like a charm. Thanks.
haribalaji said:
Wow.. I followed your instructions and it worked like a charm. Thanks.
Click to expand...
Click to collapse
No worries bro... Glad it worked
Related
Hi, im using CM11 nightly GT-i9100G.. After finish flashing, after updating binary on SuperSU, it ask me to reboot (recommended). When i reboot onto recovery mode, and install aidfarh kernel, it ask me to fix root. everytime if im booting into recovery. Why is that? Please help me. TQ
khyriel said:
Hi, im using CM11 nightly GT-i9100G.. After finish flashing, after updating binary on SuperSU, it ask me to reboot (recommended). When i reboot onto recovery mode, and install aidfarh kernel, it ask me to fix root. everytime if im booting into recovery. Why is that? Please help me. TQ
Click to expand...
Click to collapse
U dont need to select recovery method when super su asked u to updtae su binary.
Thats for htc devices.
Select normal install method
SENT USING VIVELROM_OMNI
corruptionfreeindia said:
U dont need to select recovery method when super su asked u to updtae su binary.
Thats for htc devices.
Select normal install method
SENT USING VIVELROM_OMNI
Click to expand...
Click to collapse
I do select the normal one. but this is when i reboot into recovery mode. its gone now after o change to TWRP recovery from CWM recovery. i will do a backup and see what will happen next.
after update to latest nightly 4.4.2 KK, i make a backup in Nandroid using CWM Recovery, after finish doing backup, it ask me to fix root? am i the only 1 having this? Just a question.
khyriel said:
after update to latest nightly 4.4.2 KK, i make a backup in Nandroid using CWM Recovery, after finish doing backup, it ask me to fix root? am i the only 1 having this? Just a question.
Click to expand...
Click to collapse
Flash supersu.zip
It's available both in infected omni and vivekrom omni thread.
Sent from my GT-I9100 using Tapatalk 2
I have a Galaxy Alpha model SM-G850M, I rooted it and it worked fine, but a few days later I restarted my device and root was gone, i only had the SuperSu app. So i tried to root it again with odin and the CF Autoroot but id don't worked any more. I nade the wipe data factory reset and tried to root again and it gain failed.
Please help mee!!!!!! :crying:
Sebastian.Peter said:
I have a Galaxy Alpha model SM-G850M, I rooted it and it worked fine, but a few days later I restarted my device and root was gone, i only had the SuperSu app. So i tried to root it again with odin and the CF Autoroot but id don't worked any more. I nade the wipe data factory reset and tried to root again and it gain failed.
Please help mee!!!!!! :crying:
Click to expand...
Click to collapse
With ODIN root and install TWRP. After that flash via TWRP SuperSU flashable ZIP and BusyBox, also flashable ZIP and you should be OK.
UniversalKID said:
With ODIN root and install TWRP. After that flash via TWRP SuperSU flashable ZIP and BusyBox, also flashable ZIP and you should be OK.
Click to expand...
Click to collapse
Thanks, !! I'm gonna try it. But I'm so happy for your answer!!
UniversalKID said:
With ODIN root and install TWRP. After that flash via TWRP SuperSU flashable ZIP and BusyBox, also flashable ZIP and you should be OK.
Click to expand...
Click to collapse
Hello again Universalkid, I tried to do taht but I domn´t know what is a TWRP an how can I flash Supersu via TWRP. Can u explain me how to do the whole process? Please!! Greetings from Switzerland!!
If you don't know what it is, and are too lazy to Google, it means you shouldn't be doing this.
Wysłane z mojego SM-G850F przy użyciu Tapatalka
Sebastian.Peter said:
Hello again Universalkid, I tried to do taht but I domn´t know what is a TWRP an how can I flash Supersu via TWRP. Can u explain me how to do the whole process? Please!! Greetings from Switzerland!!
Click to expand...
Click to collapse
TWRP is a custom recovery. But before you do all that, I suggest you to google all about custom recovery, SuperSU, BusyBox and how to flash ZIP's from TWRP. Read carefully all the instructions and tutorials and only after you done that, go ahead and try it on your phone. This way you will not brick your device. Good Luck.
Re-authentication
I successfully installed TWRP, and after that, I installed SuperSU. I works at first, but after rebooted the device, re-authentication doesn't work. I can still use SuperSU to root apps, but just first time. Not after rebooted.
Hello guys,
I yesterday updated to CM13(from cm11),found as an update in CyanogenMod Updates 18.12.2015.
I firstly thought that it wouldnt need new gapps or wipe data/cache,till i find out that after install my i9300 couldnt leave Boot.
After that i tried to do a factory reset/wipe cache partition/wipe dalvik and then reinstall cm13 update only to find out that the problem hasn't been resolved....
Should i try to install CM13 and Gapps 6.0 through ODIN?
what will fix my problem?
Thanks in advance for your time.
I also,tried to factory reset/etc. to install the previous update that i had (cm11 ) but the problem persists!
SOLUTION
So finally I resolved the issue!
Thanks very much for help v7!
I 'll write here all the steps that i did to find the solution in case someone in the future straggle with the same problem.
1)I ve incorrectly tried to install the CM13 as an CM update (previous version: CM11)
2)After the install I couldnt get pass the CM Boot icon and i could only access the recovery mode.
3)Tried to flash previous CM11 versions (also did factory reset,cache and dalvik) but it didn't help.
So the steps to the solution to the problem were:
1)Factory reset and power off the phone
2)Found (as v7 pointed) the stock firmware through here: http://samsung-updates.com/device/ (be carefull to choose the right hardware!)
3)Connect I9300 to Odin software While phone is in download mode (you can enter by pressing HOME Button+Power Button+Volume Down)
4)Choose through the PDA option in Odin the firmware that you 've downloaded (the file type will be in MD5 form so u might need to unzip first)
5)Hit Start Button and leave all the other features intact in ODIN!
6)after installation boot into the stock firmware that you ve just installed.
7)If the boot finished succesfully then continue:
8)Find an Software or a .tar file to REROOT your phone (i ve used CF-autoroot file,which i installed through odin -as you did with the stock firmware)
9)After installing the Root,Boot again the phone,download SuperSU (through playstore), then download root checker and finally flashify so you will be able to install TWRP recovery.
10)Approve Root checker and flashify through SuperSU(in order to verify your root and later flash TWRP)
11)Download latest TWRP (v7 suggested https://dl.twrp.me/i9300/twrp-2.8.7.3-i9300.img ) and copy it to your ext.SD Card.
12)Open Flashify and choose "Boot Image",select the twrp version you've copied in your SD Card and let it flash it.
13)After a succesfull flash,Power off your phone and press Home Button+Power Button+Volume Up to enter the TWRP recovery mode.
14)Through there you ll be able to install the latest CM13 followed by the GAPPS (which are needed in order to have access to Playstore)
You can download the latest Nightly version through here: http://get.cm/?device=i9300&type=nightly
and the latest GAPPS through here: https://www.androidfilehost.com/?w=files&flid=41043 *(i ve used the latest version of mini GAPPS just to be more precise).
PanosR. said:
Hello guys,
I yesterday updated to CM13(from cm11),found as an update in CyanogenMod Updates 18.12.2015.
I firstly thought that it wouldnt need new gapps or wipe data/cache,till i find out that after install my i9300 couldnt leave Boot.
After that i tried to do a factory reset/wipe cache partition/wipe dalvik and then reinstall cm13 update only to find out that the problem hasn't been resolved....
Should i try to install CM13 and Gapps 6.0 through ODIN?
what will fix my problem?
Thanks in advance for your time.
I also,tried to factory reset/etc. to install the previous update that i had (cm11 ) but the problem persists!
Click to expand...
Click to collapse
Hello,
Thanks for using XDA Assist.
What's your recovery version?Update to latest TWRP 2.8.7.3 abd flash the ROM.Make sure you use Slim GAPPS.
___
v7
XDA Assist
v7 said:
Hello,
Thanks for using XDA Assist.
What's your recovery version?Update to latest TWRP 2.8.7.3 abd flash the ROM.Make sure you use Slim GAPPS.
___
v7
XDA Assist
Click to expand...
Click to collapse
Hello,and thanks for your time!
i have ClockworkMod Recovery v6.0.4.6 (if thats what you mean).Should i update?and if yes,how?(through Odin?)
Any Link for the correct GAPPS?
Cause i ve downloaded "open.gapps-arm-6.0-full-20151113"
Should i install Cm13 and GAPPS through odin? cause i cant go back to cm11,as i ve edited.
Also,should be the kernel updated to boeffla?
PanosR. said:
Hello,and thanks for your time!
i have ClockworkMod Recovery v6.0.4.6 (if thats what you mean).Should i update?and if yes,how?(through Odin?)
Any Link for the correct GAPPS?
Cause i ve downloaded "open.gapps-arm-6.0-full-20151113"
Should i install Cm13 and GAPPS through odin? cause i cant go back to cm11,as i ve edited.
Also,should be the kernel updated to boeffla?
Click to expand...
Click to collapse
Moving your thread to S III Q&A,Help and Troubleshooting
Yes.Update the recovery to TWRP 2.8.6.0+.
You can find the .tar file here TWRP-I9300.Flash it from Odin.
Now from TWRP,flash CM13 followed by SLIM GAPPS.Make sure you flash both together else you'll face freezes.
___
v7
XDA Assist
v7 said:
Moving your thread to S III Q&A,Help and Troubleshooting
Yes.Update the recovery to TWRP 2.8.6.0+.
You can find the .tar file here TWRP-I9300.Flash it from Odin.
Now from TWRP,flash CM13 followed by SLIM GAPPS.Make sure you flash both together else you'll face freezes.
___
v7
XDA Assist
Click to expand...
Click to collapse
Ok!i ll download immidiately and keep you up to date if anything changes!
Btw Slim Mini or Zero GAPPS?
Hello again..
I ve downloaded the twrp file that you suggested "twrp-2.8.6.1-i9300.tar 7.7M",installed it throught ODIN (i got a Pass) but now i cant enter Recovery mode!
PanosR. said:
Hello again..
I ve downloaded the twrp file that you suggested "twrp-2.8.6.1-i9300.tar 7.7M",installed it throught ODIN (i got a Pass) but now i cant enter Recovery mode!
Click to expand...
Click to collapse
Hardware key combo isn't working?
___
v7
XDA Assist
v7 said:
Hardware key combo isn't working?
___
v7
XDA Assist
Click to expand...
Click to collapse
No,it stucks where "Samsung Galaxy I9300" appears and doesnt enter in recovery..
Nevertheless i reinstalled CWM,updated it and now and can re-enter recovery..
I tried to do again factory reset etc. etc.
installed the latest version of cm13 with the gapps that you suggested but i get stucked again in the boot..
I ve w8ed for 20minutes but it s still loading...
PanosR. said:
No,it stucks where "Samsung Galaxy I9300" appears and doesnt enter in recovery..
Nevertheless i reinstalled CWM,updated it and now and can re-enter recovery..
I tried to do again factory reset etc. etc.
installed the latest version of cm13 with the gapps that you suggested but i get stucked again in the boot..
I ve w8ed for 20minutes but it s still loading...
Click to expand...
Click to collapse
Did you try flashing the latest TWRP from CWM?
___
v7
XDA Assist
v7 said:
Did you try flashing the latest TWRP from CWM?
___
v7
XDA Assist
Click to expand...
Click to collapse
No,will this work?
Do i surely need twrp to install CM13?
Can't make it work through the latest CWM?
PanosR. said:
No,will this work?
Do i surely need twrp to install CM13?
Can't make it work through the latest CWM?
Click to expand...
Click to collapse
Flash the CM11 once and flash TWRP using Flashify app/TWRP Manager.
Link to latest TWRP 2.8.7.3.img
___
v7
XDA Assist
v7 said:
Flash the CM11 once and flash TWRP using Flashify app/TWRP Manager.
Link to latest TWRP 2.8.7.3.img
___
v7
XDA Assist
Click to expand...
Click to collapse
Flashed CM11 and again stucked at boot... 15mins since I boot..Should i wait more or is there a problem?
PanosR. said:
Flashed CM11 and again stucked at boot... 15mins since I boot..Should i wait more or is there a problem?
Click to expand...
Click to collapse
This is weird.Wait for 5-10 minutes.If it doesn't work,flash your stock firmware or restore a backup is you have one.
___
v7
XDA Assist
v7 said:
This is weird.Wait for 5-10 minutes.If it doesn't work,flash your stock firmware or restore a backup is you have one.
___
v7
XDA Assist
Click to expand...
Click to collapse
Hello again,finally!I ve been downloading with 50kb/s the stock firmware and i ve managed to install it.
So what do i do now? the phone boot up normally..
How do i finally install twrp and the cm13?
PanosR. said:
Hello again,finally!I ve been downloading with 50kb/s the stock firmware and i ve managed to install it.
So what do i do now? the phone boot up normally..
How do i finally install twrp and the cm13?
Click to expand...
Click to collapse
Root your phone via odin
Install twrp via odin
Flash cm13 with gapps via twrp
Enjoy
Note:backup your efs(for bad days)
SOLVED
So finally I resolved the issue!
Thanks very much for help v7!
I 'll write here all the steps that i did to find the solution in case someone in the future straggle with the same problem.
1)I ve incorrectly tried to install the CM13 as an CM update (previous version: CM11)
2)After the install I couldnt get pass the CM Boot icon and i could only access the recovery mode.
3)Tried to flash previous CM11 versions (also did factory reset,cache and dalvik) but it didn't help.
So the steps to the solution to the problem were:
1)Factory reset and power off the phone
2)Found (as v7 pointed) the stock firmware through here: http://samsung-updates.com/device/ (be carefull to choose the right hardware!)
3)Connect I9300 to Odin software While phone is in download mode (you can enter by pressing HOME Button+Power Button+Volume Down)
4)Choose through the PDA option in Odin the firmware that you 've downloaded (the file type will be in MD5 form so u might need to unzip first)
5)Hit Start Button and leave all the other features intact in ODIN!
6)after installation boot into the stock firmware that you ve just installed.
7)If the boot finished succesfully then continue:
8)Find an Software or a .tar file to REROOT your phone (i ve used CF-autoroot file,which i installed through odin -as you did with the stock firmware)
9)After installing the Root,Boot again the phone,download SuperSU (through playstore), then download root checker and finally flashify so you will be able to install TWRP recovery.
10)Approve Root checker and flashify through SuperSU(in order to verify your root and later flash TWRP)
11)Download latest TWRP (v7 suggested https://dl.twrp.me/i9300/twrp-2.8.7.3-i9300.img ) and copy it to your ext.SD Card.
12)Open Flashify and choose "Boot Image",select the twrp version you've copied in your SD Card and let it flash it.
13)After a succesfull flash,Power off your phone and press Home Button+Power Button+Volume Up to enter the TWRP recovery mode.
14)Through there you ll be able to install the latest CM13 followed by the GAPPS (which are needed in order to have access to Playstore)
You can download the latest Nightly version through here: http://get.cm/?device=i9300&type=nightly
and the latest GAPPS through here: https://www.androidfilehost.com/?w=files&flid=41043 *(i ve used the latest version of mini GAPPS just to be more precise).
Heykır said:
Root your phone via odin
Install twrp via odin
Flash cm13 with gapps via twrp
Enjoy
Note:backup your efs(for bad days)
Click to expand...
Click to collapse
Yeah already done mate!
Thanks,I just though that i wouldnt have to do the whole process again,but i find out few hours ago that this would be the only solution!
Thanks both of you for your time!
Hello XDA,
I have android phone version 5.1 (lollipop) and I want to install XPosed Framework in my phone but sadly I always got Error message whenever I tried flashing it.
It always says:
E: Failed to verify whole-file signature.
E: Signature verification failed.
Installation aborted.
Here's some screenshot for better understanding.
Sadly, I can't post screenshots due to lack of post. Please reply if you need to see the screenshots so I can send it to you via private message.
Click to expand...
Click to collapse
I saw some tutorial on the other sites and they posted some screenshots about their processor, I think you need to know..
Processor: ARMv7 processor rev 5 (v71)
Cores: 4
Hope my problem can be solve quickly.
Thanks!
m0kiee said:
Hello XDA,
I have android phone version 5.1 (lollipop) and I want to install XPosed Framework in my phone but sadly I always got Error message whenever I tried flashing it.
It always says:
E: Failed to verify whole-file signature.
E: Signature verification failed.
Installation aborted.
Here's some screenshot for better understanding.
I saw some tutorial on the other sites and they posted some screenshots about their processor, I think you need to know..
Processor: ARMv7 processor rev 5 (v71)
Cores: 4
Hope my problem can be solve quickly.
Thanks!
Click to expand...
Click to collapse
Which version zip you downloaded ?
LoverBoy2415 said:
Which version zip you downloaded ?
Click to expand...
Click to collapse
I've downloaded the lastest one,
framework/sdk22/arm/xposed-v84-sdk22-arm.zip
I also tried the v80 because someone told me that.
m0kiee said:
I've downloaded the lastest one,
framework/sdk22/arm/xposed-v84-sdk22-arm.zip
I also tried the v80 because someone told me that.
Click to expand...
Click to collapse
Which recovery are you using ?
LoverBoy2415 said:
Which recovery are you using ?
Click to expand...
Click to collapse
Android system recovery <3e>.
I think it's my default android recovery..
I just choose update from sd card.
m0kiee said:
Android system recovery .
I think it's my default android recovery..
I just choose update from sd card.
Click to expand...
Click to collapse
WHAT!!! stock recovery [emoji40] ..
Then How xposed will be installed..
You need a custom Recovery like TWRP,Philz To Install Xposed ..
LoverBoy2415 said:
WHAT!!! stock recovery [emoji40] ..
Then How xposed will be installed..
You need a custom Recovery like TWRP,Philz To Install Xposed ..
Click to expand...
Click to collapse
I've downloaded TWRP Manager from google play store. When I open it, a message shown saying "You don't have busybox installed. Would you like to install it now?" then when I clicked OK nothing shown to install busybox.
Then I proceed to Menu > Install. I added the v84 zip file and leaving Backup, Wipe Data, Wipe Cache, Wipe Dalvik UNCHECKED then I clicked Flash Now and then a message box appeared saying "Are you sure you want to reboot to recovery and complete specified actions?" then OK and there you go, I moved to default recovery.
m0kiee said:
I've downloaded TWRP Manager from google play store. When I open it, a message shown saying "You don't have busybox installed. Would you like to install it now?" then when I clicked OK nothing shown to install busybox.
Then I proceed to Menu > Install. I added the v84 zip file and leaving Backup, Wipe Data, Wipe Cache, Wipe Dalvik UNCHECKED then I clicked Flash Now and then a message box appeared saying "Are you sure you want to reboot to recovery and complete specified actions?" then OK and there you go, I moved to default recovery.
Click to expand...
Click to collapse
First thing is , You don't have A Custom Recovery in Your Device,first you should install it ..Then Only you can able to Flash xposed zip successful..
---------- Post added at 02:39 PM ---------- Previous post was at 02:37 PM ----------
m0kiee said:
I've downloaded TWRP Manager from google play store. When I open it, a message shown saying "You don't have busybox installed. Would you like to install it now?" then when I clicked OK nothing shown to install busybox.
Then I proceed to Menu > Install. I added the v84 zip file and leaving Backup, Wipe Data, Wipe Cache, Wipe Dalvik UNCHECKED then I clicked Flash Now and then a message box appeared saying "Are you sure you want to reboot to recovery and complete specified actions?" then OK and there you go, I moved to default recovery.
Click to expand...
Click to collapse
Search Custom Recovery for Your Device & Install it first ..
@m0kiee
Please share you device name, model. Search for TWRP/CWM recovery for your device model.
Another method :
Install Flashfire from here --> http://flashfireapk.com/FlashFire-Download.html
Flash the xposed zip using Flashfire app.
LoverBoy2415 said:
Search Custom Recovery for Your Device & Install it first ..
Click to expand...
Click to collapse
Sadly but there are no available custom recovery for my device. I did a lot of research, downloading some custom recovery installer but nothing works fine.
I think I should get satisfied of what my phone have
m0kiee said:
Sadly but there are no available custom recovery for my device. I did a lot of research, downloading some custom recovery installer but nothing works fine.
I think I should get satisfied of what my phone have
Click to expand...
Click to collapse
Well Yes , then Try Flashfire App from Google play & Flash the Zip through it ..I Think it will work ..
Flashfire won't read my root
m0kiee said:
Flashfire won't read my root
Click to expand...
Click to collapse
Which App You Using ,SuperSU or Kingroot(Kinguser)
LoverBoy2415 said:
Which App You Using ,SuperSU or Kingroot(Kinguser)
Click to expand...
Click to collapse
Kingroot.
m0kiee said:
Kingroot.
Click to expand...
Click to collapse
If Possible Can You try With SuperSU ? I Thing Flashfire Doesn't work with Kingroots Su Binaries ..That's why you didn't get the Prompt
LoverBoy2415 said:
If Possible Can You try With SuperSU ? I Thing Flashfire Doesn't work with Kingroots Su Binaries ..That's why you didn't get the Prompt
Click to expand...
Click to collapse
I can't change to superSU. Framaroot (superSU) doesn't support android 5.1. I can't flash superSU using stock recovery right?
m0kiee said:
I can't change to superSU. Framaroot (superSU) doesn't support android 5.1. I can't flash superSU using stock recovery right?
Click to expand...
Click to collapse
Why are you Using Framaroot, Framaroot is for Jellybean Only..
There are so many guides in Google & XDA on HOW TO REPLACE KingRoot With SuperSU ..Search Those & Do As it is ..You Will Have SuperSU on Your Device .. Then Do Flashing With FlashFire ..
Yes,You Can't ,SuperSU Requires a Custom Recovery to Flash ..
Hello guys, I recently rooted my moto e 5.1 using "theunlockr.com" site's method, and used cwm recovery mod! now I downloaded cm13 for my phone, I noticed that there is no method installing cm 13 with cwm method! Please help me on how to install cm 13 with cwm! My phone is now just rooted! I'm totally noob to cm 13, I also saw an .IMG file on cyanogenmod's moto e page, what's the use of it? I now currently have a cm zip file and an IMG file, and have cwm recovery, please help me installing cm 13 on my phone!
lionking5202 said:
Hello guys, I recently rooted my moto e 5.1 using "theunlockr.com" site's method, and used cwm recovery mod! now I downloaded cm13 for my phone, I noticed that there
Click to expand...
Click to collapse
Cwm is not supported. Flash twrp
About .img file, it's CyanogenMod recovery. There is no need to flash that .IMG file which you downloaded from cm website. Just flash twrp
drs22 said:
Cwm is not supported. Flash twrp
About .img file, it's CyanogenMod recovery. There is no need to flash that .IMG file which you downloaded from cm website. Just flash twrp
Click to expand...
Click to collapse
if you please give me the link of twrp recovery method that'll be helpful!
lionking5202 said:
if you please give me the link of twrp recovery method that'll be helpful!
Click to expand...
Click to collapse
Here
Or if your phone is rooted, you can also use flashify (search on play store)
drs22 said:
Here
Or if your phone is rooted, you can also use flashify (search on play store)
Click to expand...
Click to collapse
its rooted with cwm recovery already
lionking5202 said:
its rooted with cwm recovery already
Click to expand...
Click to collapse
Then install flashify. Select recovery from flashify's main screen>download twrp >select moto e > twrp 3.0.2
drs22 said:
Then install flashify. Select recovery from flashify's main screen>download twrp >select moto e > twrp 3.0.2
Click to expand...
Click to collapse
is it possible to flash twrp if thers already cwm installed in my phone? i will face any problem or not?
lionking5202 said:
is it possible to flash twrp if thers already cwm installed in my phone? i will face any problem or not?
Click to expand...
Click to collapse
Nope. Well, first make a backup from cwm for safety
lionking5202 said:
is it possible to flash twrp if thers already cwm installed in my phone? i will face any problem or not?
Click to expand...
Click to collapse
Download the app "twrp manager" from playstore
Open the app
Grant superuser acces
Select an device (moto e, not moto e 2015)
Install and wait
When the process is finished you can reboot to recovery and flash cyanogenmod 13
This method is totally safe
And you need flash gapps if you want the playstore and other apps of google, use open gapps project
hetor99 said:
Download the app "twrp manager" from playstore
Open the app
Grant superuser acces
Select an device (moto e, not moto e 2015)
Install and wait
When the process is finished you can reboot to recovery and flash cyanogenmod 13
This method is totally safe
And you need flash gapps if you want the playstore and other apps of google, use open gapps project
Click to expand...
Click to collapse
Are you sure bro? Because I already have cwm recovery installed in my phone! Will it work? I don't wanna brick my phone!!!
lionking5202 said:
Are you sure bro? Because I already have cwm recovery installed in my phone! Will it work? I don't wanna brick my phone!!!
Click to expand...
Click to collapse
I have already said it. First make a nandroid backup from cwm and then flash twrp
drs22 said:
I have already said it. First make a nandroid backup from cwm and then flash twrp
Click to expand...
Click to collapse
I went into cwm recovery mode and selected backup, but it failed i think because of low storage in my phone which was 699 mb!
and now my internal storage is running out of space! i only have uc browser, supersu, rom manager installed in my phone! should i factory reset my phone?
lionking5202 said:
I went into cwm recovery mode and selected backup, but it failed i think because of low storage in my phone which was 699 mb!
and now my internal storage is running out of space! i only have uc browser, supersu, rom manager installed in my phone! should i factory reset my phone?
Click to expand...
Click to collapse
You could have backed it up in external storage. Anyways, you may do factory reset but all your data will be deleted.
Or you may try to free up at least 100 mb by clearing cache and deleting unnecessary data so that you can install flashify and flash twrp from it.
lionking5202 said:
Are you sure bro? Because I already have cwm recovery installed in my phone! Will it work? I don't wanna brick my phone!!!
Click to expand...
Click to collapse
This process is fully safe bro and the cwm recovery dont are supported anymore by cyanogenmod and is abandoned, if you want install cyanogenmod 13 install twrp 3.0.2
And if something brick your device, it can be fixed easy
thanks guys i'll let ya know if i got success
drs22 said:
You could have backed it up in external storage. Anyways, you may do factory reset but all your data will be deleted.
Or you may try to free up at least 100 mb by clearing cache and deleting unnecessary data so that you can install flashify and flash twrp from it.
Click to expand...
Click to collapse
hey guys now which one to use flashify or twrp manager
lionking5202 said:
hey guys now which one to use flashify or twrp manager
Click to expand...
Click to collapse
You can chose either of them
lionking5202 said:
Are you sure bro? Because I already have cwm recovery installed in my phone! Will it work? I don't wanna brick my phone!!!
Click to expand...
Click to collapse
this dont brick the device, the changes are aplied to the recovery partition, doesn`t make changes to boot.img partition or system partition, its 100% safe.
And twrp is best, cwm are abandoned by their comunity and dont are supported by too much roms
sorry for my english
Thanks guys, successfully installed cm 13, but now I'm facing a problem, i flashed gapps zip and now Google play services is now showing "unfortunately Google play services has been stopped" gave all the permissions! But still it's coming again and again! I'm not able to track my location in Google maps!!!!!