Hi all, i want to unblock bootloader for my Che2-L11 and I already get the 16-digit code from huawei website.
Unfortunately I fail in the first step because even the fastboot mode also cannot enter even I tried to use different method to enter the fastboot mode but still failed. .Anyone face this problem before ?
volume down + power button = no vibrate and straight enter system.
volume down + up+power = error message"no UPDATE.APP found".
After done research and I get know the UPDATE.APP is the file inside the dload folder that I was downloaded from hua wei website last few day for upgrade to 5.1.1 lollipop and yet now I copy the whole dload folder to sd card and try again see.
*will update if I can get in the fastmode
okay.........volume up+down+power is just upgrade the phone system and does not enter to fastboot mode.
Related
Hi,
I need these files
1.fastboot flash recovery stock_recovery.smg
2.pudding_stock_unlock
Note : This site went offline http://mophoforum.com/Roms/1FF-sunf...198_7-CM-release-keys-signed-Sprint-US.sbf.gz, I also tried another website which is also not working.
Now the problem is I need this files fastboot flash recovery stock_recovery.smg as feautred here http://forum.xda-developers.com/showthread.php?t=1216143, rest pudding stock.rar also needed.
And according to this http://forum.xda-developers.com/showthread.php?t=1573727 it says that I need to enter into fastboot, however I have tried both method Volume up +Power button and Volume Down + Power button, but I cant enter in to fastboot, what I see is only Starting RSD protocol support
Regards
First of all I would thank Crowds he is the best reference that I've to return in case of any problem I face. (He doesn't sleep - any time I ask he immediately supports)
I bought Lenovo K910 and I've managed successfully to install new ROM "VIBEUI_v2.0_1443" and Gapps with Crowds support.
I advised two of my friends to buy this good and cheap phone. For one of them I installed the latest rom successfully. But with the other I had a big problem The phone stuck on Lenovo Logo.
I was trying to install TWRP 2.7.0.0 batch before installing my new ROM, but during installation and after the phone rebooting the batch command screen shows <Waiting for Device> and the phone is stuck on logo screen.
I tried to connect the phone to PC many times, but PC doesn't recognize the phone. When I try to turn off the phone by pressing the power buttons, the phone restart on logo screen like the shown in this video.
I've read in many site that I have to do the following:
Download and install "minimal adb and fastboot"
Just type on the command line without pressing Enter:
Code:
[COLOR="Blue"][B][I]fastboot [COLOR="Plum"][STRIKE]boot[/STRIKE][/COLOR] recovery.img[/I][/B][/COLOR]
you should place your recovery image file in "minimal adb and fastboot" directory
The phone should be disconnected from computer and completely off (press the Power button for 10 seconds - in my case the phone is restarting)
Press and hold both volume buttons, then connect the cable to the PC.
Once the phone vibrate, press Enter to execute the recovery command line
Click to expand...
Click to collapse
In my case when I press and hold power button the phone is restarting on logo screen so I have to wait for battery consumption
I tried many times with TWRP images but it failed...
I tried with CWM image and it succeeded to load, but I don't have otg cable to load recovery or ROM from usb storage (The problem was in installing TWRP and my ROM should has no problem)
I want to flash TWRP on phone not only loading by "minimal adb and fastboot".
I decided to flash TWRP 2.7.1.2 batch through modifying the batch file. I just used fastboot commands
Code:
[COLOR="blue"][I]fastboot oem device-info
fastboot oem unlock
fastboot oem device-info
fastboot [COLOR="Red"][U][B]flash[/B][/U][/COLOR] recovery data/recovery.img
fastboot flash aboot data/lock/emmc_appsboot.mbn
fastboot flash rpm data/lock/rpm.mbn
fastboot flash sbl1 data/lock/sbl1.mbn
fastboot flash dbi data/lock/sdi.mbn
fastboot flash tz data/lock/tz.mbn
fastboot reboot[/I][/COLOR]
Finally I succeeded to install Recovery and phone works well in the new recovery mode and the system mode that I've not update it yet
I want to share you the problem solution in brief:
Download and extract this file "flashrec TWRP v2.7.1.2" from here
Just select without executing "flashrec_Modified.bat" file from the extracted files.
The phone should be disconnected from computer and completely off (press the Power button for 10 seconds or wait for the battery to be almost empty)
Press and hold both volume buttons, then connect the cable to the PC.
Once the phone vibrate, press Enter to execute the recovery batch file
and as me the phone start the recovery mode in TWRP and can be rebooted in system without any problem
i must extract "flashrec TWRP v2.7.1.2 this file on phone or where? can u explain a
agsao said:
First of all I would thank Crowds he is the best reference that I've to return in case of any problem I face. (He doesn't sleep - any time I ask he immediately supports)
I bought Lenovo K910 and I've managed successfully to install new ROM "VIBEUI_v2.0_1443" and Gapps with Crowds support.
I advised two of my friends to buy this good and cheap phone. For one of them I installed the latest rom successfully. But with the other I had a big problem The phone stuck on Lenovo Logo.
I was trying to install TWRP 2.7.0.0 batch before installing my new ROM, but during installation and after the phone rebooting the batch command screen shows <Waiting for Device> and the phone is stuck on logo screen.
I tried to connect the phone to PC many times, but PC doesn't recognize the phone. When I try to turn off the phone by pressing the power buttons, the phone restart on logo screen like the shown in this video.
I've read in many site that I have to do the following:
In my case when I press and hold power button the phone is restarting on logo screen so I have to wait for battery consumption
I tried many times with TWRP images but it failed...
I tried with CWM image and it succeeded to load, but I don't have otg cable to load recovery or ROM from usb storage (The problem was in installing TWRP and my ROM should has no problem)
I want to flash TWRP on phone not only loading by "minimal adb and fastboot".
I decided to flash TWRP 2.7.1.2 batch through modifying the batch file. I just used fastboot commands
Code:
[COLOR="blue"][I]fastboot oem device-info
fastboot oem unlock
fastboot oem device-info
fastboot [COLOR="Red"][U][B]flash[/B][/U][/COLOR] recovery data/recovery.img
fastboot flash aboot data/lock/emmc_appsboot.mbn
fastboot flash rpm data/lock/rpm.mbn
fastboot flash sbl1 data/lock/sbl1.mbn
fastboot flash dbi data/lock/sdi.mbn
fastboot flash tz data/lock/tz.mbn
fastboot reboot[/I][/COLOR]
Finally I succeeded to install Recovery and phone works well in the new recovery mode and the system mode that I've not update it yet
I want to share you the problem solution in brief:
Download and extract this file "flashrec TWRP v2.7.1.2" from here
Just select without executing "flashrec_Modified.bat" file from the extracted files.
The phone should be disconnected from computer and completely off (press the Power button for 10 seconds or wait for the battery to be almost empty)
Press and hold both volume buttons, then connect the cable to the PC.
Once the phone vibrate, press Enter to execute the recovery batch file
and as me the phone start the recovery mode in TWRP and can be rebooted in system without any problem
Click to expand...
Click to collapse
Please explain me. idont know how to do
prxzero said:
Please explain me. idont know how to do
Click to expand...
Click to collapse
What Is your problem?
Is your phone stuck on logo screen? what were you doing to get the problem??
agsao said:
First of all I would thank Crowds he is the best reference that I've to return in case of any problem I face. (He doesn't sleep - any time I ask he immediately supports)
I bought Lenovo K910 and I've managed successfully to install new ROM "VIBEUI_v2.0_1443" and Gapps with Crowds support.
I advised two of my friends to buy this good and cheap phone. For one of them I installed the latest rom successfully. But with the other I had a big problem The phone stuck on Lenovo Logo.
I was trying to install TWRP 2.7.0.0 batch before installing my new ROM, but during installation and after the phone rebooting the batch command screen shows <Waiting for Device> and the phone is stuck on logo screen.
I tried to connect the phone to PC many times, but PC doesn't recognize the phone. When I try to turn off the phone by pressing the power buttons, the phone restart on logo screen like the shown in this video.
I've read in many site that I have to do the following:
In my case when I press and hold power button the phone is restarting on logo screen so I have to wait for battery consumption
I tried many times with TWRP images but it failed...
I tried with CWM image and it succeeded to load, but I don't have otg cable to load recovery or ROM from usb storage (The problem was in installing TWRP and my ROM should has no problem)
I want to flash TWRP on phone not only loading by "minimal adb and fastboot".
I decided to flash TWRP 2.7.1.2 batch through modifying the batch file. I just used fastboot commands
Code:
[COLOR="blue"][I]fastboot oem device-info
fastboot oem unlock
fastboot oem device-info
fastboot [COLOR="Red"][U][B]flash[/B][/U][/COLOR] recovery data/recovery.img
fastboot flash aboot data/lock/emmc_appsboot.mbn
fastboot flash rpm data/lock/rpm.mbn
fastboot flash sbl1 data/lock/sbl1.mbn
fastboot flash dbi data/lock/sdi.mbn
fastboot flash tz data/lock/tz.mbn
fastboot reboot[/I][/COLOR]
Finally I succeeded to install Recovery and phone works well in the new recovery mode and the system mode that I've not update it yet
I want to share you the problem solution in brief:
Download and extract this file "flashrec TWRP v2.7.1.2" from here
Just select without executing "flashrec_Modified.bat" file from the extracted files.
The phone should be disconnected from computer and completely off (press the Power button for 10 seconds or wait for the battery to be almost empty)
Press and hold both volume buttons, then connect the cable to the PC.
Once the phone vibrate, press Enter to execute the recovery batch file
and as me the phone start the recovery mode in TWRP and can be rebooted in system without any problem
Click to expand...
Click to collapse
Hi..
i just try to install CM12 to this device, with twrp 2.8.6.1 from master lie.
First time its working well, but suddenly this device restarting and stuck on the "lenovo" logo screen.
Every time i presh power button always restarting (like ON-OFF-ON-OFF forever).
when i connectto charger also restarting....
i cant go to twrp using vol- & pwr, when i use minimal adb cannot detected..
Can you help me...
Help
hi.
i try to do something to enable notifications on my lenovo vibe z.
i install new rom from needrom, but it didn't help. So i try to install other one, but i wipe my phone and restart without installed system.
Now when i go to twrp have just flashing teamwin logo, and only when phone is in this mode i can communicate through adb
i have checked many forums and try allot stuff to fix it but nothing works
Please Help!
U are not alone I also in same stage
Is there any one plz help
As long as the hardware is not physically broken, your K910 is unbrickable
http://www.teamsuperluminal.org/unbrick-lenovo-k910/
I followed the guide to revive my K910. You can refer to this forum post in which I documented my experiences:
http://www.teamsuperluminal.org/forums/topic/flash-back-to-lenovo-stock-just-temporarily/
nowbo said:
Is there any one plz help
Click to expand...
Click to collapse
Thanks for your reply
I will apply today. Hope for the best.
Will inform you as soon as this applied..
Have you fixed that problem?
Still at same stage
EcoDan said:
Have you fixed that problem?
Click to expand...
Click to collapse
Hi,
I am still on same stage (Black screen with lenovo logo). Try several ways but can't get out of this. Please help me If any one successful to startup this device or can get on the boot screen where I can do factory reset.
---------- Post added at 07:25 AM ---------- Previous post was at 07:21 AM ----------
wxppro said:
http://www.teamsuperluminal.org/unbrick-lenovo-k910/
I followed the guide to revive my K910. You can refer to this forum post in which I documented my experiences:
http://www.teamsuperluminal.org/forums/topic/flash-back-to-lenovo-stock-just-temporarily/
Click to expand...
Click to collapse
I Try this method but can't get out from that black screen ( Lenovo logo and powered by android)
My device is Lenovo Vibe shot Z90a40. I also try with boot unlock-er but nothing sitll work. So its about 20 days can't use my Lenovo Vibe Shot.
Please help me If you know how to get out of this issue..
Thanks
[/COLOR]
I Try this method but can't get out from that black screen ( Lenovo logo and powered by android)
My device is Lenovo Vibe shot Z90a40. I also try with boot unlock-er but nothing sitll work. So its about 20 days can't use my Lenovo Vibe Shot.
Please help me If you know how to get out of this issue..
Thanks[/QUOTE]
You need to carefully follow each steps in the method - if you short that magic pin and then connect the USB cable (with battery disconnected), your computer will report seeing the device at either COM port 9008 or 9006. Then you can download the factory image to revive the phone. Of course you need to have the right device driver installed. Like I said, as long as the hardware is not broken, this procedure will succeed for sure.
I love you man!
I love you man! I wish you all the happiness and wealth!:victory::victory::victory::angel::angel::highfive::highfive:
guys recently I hard bricked my phone after installing lenovo lollipoprom.I also installed cwm through pc but not opened recovery. Thank to ed300 for providing custom recovery for lollipop I unbricked in very simple way
This will work for you if u are not able to enter into recovery
First install minimal adb and fastboot on your PC
Then connect your phone
Then transfer img file to adb and fastboot folder
Then open command window by right clicking and shift at same time
Disconnect ur phone type fastboot flash recovery 'img file name'
Waiting for device will be seen on CMD
Then enter into fastboot mode and then connect ur phone to PC
It will automatically start installing recovery
Please help me my lenovo a6000 is not booting into system or recovery only fastest even after factory rest clear cache and dalvik installing stock rom ?
How to enter into fastboot mod
please tell me.
jatin vekariya said:
How to enter into fastboot mod
please tell me.
Click to expand...
Click to collapse
Dude seriously..???!!!
I asked you if you could enter in recovery or fastboo mode, and you said no, my phone just vibrates. If you didn't knew how to boot into fastboot you should've asked me right away.
Btw, here are the different key combos:
1) Recovery - Press VOL UP + VOL DOWN + POWER KEY and release POWER KEY once the lenovo logo shows up.
2) Fastboot - VOL DOWN + POWER KEY
3) Download Mode - VOL UP + POWER KEY
Multiple brick solution threads already exist, please search before posting your own.
Thread closed:
http://forum.xda-developers.com/lenovo-a6000/help/unbrick-lenovo-a6000-plus-lenovo-a6000-t3137247
http://forum.xda-developers.com/lenovo-a6000/help/recovery-lost-t3395356/post67247279#post67247279
Hello everyone.
I have a new Honor 5X and am having trouble getting away from the stock Chinese ROM.
Anyhow, where I'm at now is I have TWRP and CM13 installed but the phone is in a boot loop.
After research I think that my phone needs a firmware update to be able to run CM13, and there don't appear to be any CM12 ROMs.
Anyhow, I have trouble with your relevant forum post and other places on the internet because my phone is the UL00 variant. Please help me get my phone to boot into anything other than Chinese stock.
CM Forum: https://forum.cyanogenmod.org/topic...y-huawei-honor-5x-please-help/#comment-608356
XDA Forum: http://forum.xda-developers.com/hon...-unofficial-cyanogenmod-13-0-nightly-t3344499
PS: I think my TZ version is correct "Comparing TZ version TZ.BF.3.0.C3-00025 to TZ.BF.3.0.C3-00025"
Hello, to get out of the loop do the following steps to get back to stock ROM:
Download your phone's latest firmware and extract system.img, boot.img, recovery.img, cust.img from UPDATE.APP using Huawei Update Extractor tool.
Boot into bootloader mode by switching off the phone then pressing only the Vol DOWN button, and connecting it to PC simultaneously.
Flash recovery first, using this command.
Code:
fastboot flash recovery recovery.img
Flash all other extracted files similarly firing these commands.
Code:
fastboot flash boot boot.img
fastboot flash cust cust.img
fastboot flash system system.img
After doing this put that very UPDATE.APP from which you extracted the files in dload folder of your external SDCARD.
Switch off your phone, and press Vol UP + Vol DOWN + Power button simultaneously.
Your device will now get to the full stock firmware.
Hope this helps you a bit.
I am trying to return to stock after I bricked my Honor 5x. I get this error --> "error: command not allowed." My phone was rooted before I tried to return it to stock. What is causing the problem?
Had this problem days ago,
Fixed my problem by downloading Emui for my honor kiw-l21 "B130-Kuwait for me" then extracted the ZIP file and put "dload" in sd card
After that put phone to charger "Not a Pc Charger" Then pressed power button + Vol. up + Vol. down
EMUI started to install.
Hope that helps.
i root SGH i777 said:
I am trying to return to stock after I bricked my Honor 5x. I get this error --> "error: command not allowed." My phone was rooted before I tried to return it to stock. What is causing the problem?
Click to expand...
Click to collapse
Yes, if the method of manual flashing doesn't works first, try a normal force update by pressing three buttons.
DigiGoon said:
Hello, to get out of the loop do the following steps to get back to stock ROM:
Download your phone's latest firmware and extract system.img, boot.img, recovery.img, cust.img from UPDATE.APP using Huawei Update Extractor tool.
Boot into bootloader mode by switching off the phone then pressing only the Vol DOWN button, and connecting it to PC simultaneously.
Flash recovery first, using this command.
Code:
fastboot flash recovery recovery.img
Flash all other extracted files similarly firing these commands.
Code:
fastboot flash boot boot.img
fastboot flash cust cust.img
fastboot flash system system.img
After doing this put that very UPDATE.APP from which you extracted the files in dload folder of your external SDCARD.
Switch off your phone, and press Vol UP + Vol DOWN + Power button simultaneously.
Your device will now get to the full stock firmware.
Hope this helps you a bit.
Click to expand...
Click to collapse
I can't switch off the phone, it keeps rebooting into stock recovery, no option to shutdown, so i can't go into bootloader
what should i do??
When the phone gets off, press and hold Vol DOWN button and connect it to PC fast before it turns on again.
Sent from my PLK-L01 using Tapatalk
I'm sorry that probably many have asked the same quesiton, but I'm desperate. The case is I followed the guide on rootyourmobile dot com how-to-unlock-bootloader-install-twrp-and-root-huawei-honor-7 to unlock, install twrp and root. All went good until installing SuperSu through TWRP, where the installation process got cancelled and I'm now stuck at honor-logo. I can still access twrp(it's in chinese though), by holding volum up + power, but I dont manage to access fastboot mode.
I realize this is a way to go. I guess my problem is not getting into fastboot, I also tried all options under Reboot in TWRP. Should I let the battery run out? Any help is much appreciated. Hope my phone is not total garbage...
DigiGoon said:
Okay follow these step, if you don't understand any step ask again. But follow these:
Download the UPDATE.APP of the Build number you were on before.
Extract system.img, boot.img, recovery.img, cust.img from that UPDATE.APP
Flash all these files via bootloader mode, to boot into bootloader mode, once a loop is over and you see blank screen on your phone, quickly press Vol DOWN button and while pressing it connect your phone to a PC. If this doesn't work and you get into recovery, then in recovery go to option Reboot, in that select Bootloader.
Once in bootloader mode, flash these files by firing these commands from a CMD, make sure files are situated in the same location where you open up the CMD.
Code:
fastboot flash recovery recovery.img
fastboot flash system system.img
fastboot flash cust cust.img
fastboot flash boot boot.img
Now after your phone boots up normally, put the same UPDATE.APP from which these files were extracted in dload folder of your external SDcard.
Now switch off your phone and press all the three buttons(Vol UP + Vol DOWN + Power) simultaneously.
Flashing process will start.
Hope this helps.
Click to expand...
Click to collapse
mosoo said:
I'm sorry that probably many have asked the same quesiton, but I'm desperate. The case is I followed the guide on rootyourmobile dot com how-to-unlock-bootloader-install-twrp-and-root-huawei-honor-7 to unlock, install twrp and root. All went good until installing SuperSu through TWRP, where the installation process got cancelled and I'm now stuck at honor-logo. I can still access twrp(it's in chinese though), by holding volum up + power, but I dont manage to access fastboot mode.
I realize this is a way to go. I guess my problem is not getting into fastboot, I also tried all options under Reboot in TWRP. Should I let the battery run out? Any help is much appreciated. Hope my phone is not total garbage...
Click to expand...
Click to collapse
No need to open a separate threat. Check your post.
Why are you quoting my post and starting a new thread with it?