i recently bricked my a311 while swiching to stock rom via twrp it says unable to mount data, system in red color unable to do nothing what to do please help. also not taking the backup which i created via twrp same it says unable to mount please help to get life on my device
Similar Situation for me too. I tried installing Stock ROM via YGDP but it is failing after reaching 98%. There are two problems.
1. MT65XX Preloader driver apprear for few seconds in Device Manager and then goes off.
2. Getting the below error while flashing via YGDP.
15:44:01 CELL0: Check between YL-Parames Partition and PhoneInfo Failed.
15:44:01 CELL0: Check YL-Parames Partition Failed, The CPB is not for the Phone.
Please help. Any support is much appreciated!
akhil1_mishra said:
Similar Situation for me too. I tried installing Stock ROM via YGDP but it is failing after reaching 98%. There are two problems.
1. MT65XX Preloader driver apprear for few seconds in Device Manager and then goes off.
2. Getting the below error while flashing via YGDP.
15:44:01 CELL0: Check between YL-Parames Partition and PhoneInfo Failed.
15:44:01 CELL0: Check YL-Parames Partition Failed, The CPB is not for the Phone.
Please help. Any support is much appreciated!
Click to expand...
Click to collapse
You may check this thread and try the solution provided.
http://forum.xda-developers.com/a310/help/how-to-fix-ygpd-stuck-98-flashing-stock-t3380064
my device was lucky i donot know but some how i am able to mount all the stuff from a hard reset means battery out in twrp and just restore to the back up which i had created i was very luck man there i know that a lot of people always failed to install stock rom via pc thats why i had not connected it at all now i am not going to tinker with my device at all i will stick to cm12.3 only
shaijuvjohn said:
You may check this thread and try the solution provided.
http://forum.xda-developers.com/a310/help/how-to-fix-ygpd-stuck-98-flashing-stock-t3380064
Click to expand...
Click to collapse
Thanks for replying but not much help. Still same issue.
akhil1_mishra said:
Thanks for replying but not much help. Still same issue.
Click to expand...
Click to collapse
If you are able to reboot in to recovery, then download the flashable zip of stock rom available in xda and try flashing it.
shaijuvjohn said:
If you are able to reboot in to recovery, then download the flashable zip of stock rom available in xda and try flashing it.
Click to expand...
Click to collapse
Tried earlier but not much help. But came across below link and problem solved.
http://forum.xda-developers.com/a310/general/how-to-flash-8297w-cpb-roms-roms-himax-t3380055
akhil1_mishra said:
Tried earlier but not much help. But came across below link and problem solved.
http://forum.xda-developers.com/a310/general/how-to-flash-8297w-cpb-roms-roms-himax-t3380055
Click to expand...
Click to collapse
Yeah, good. I already seen that thread, but forgot. There is always a solution for each problem in xda. Most of the custom rom users had once gone through one of these situations and there for a solution is there.
i assume u have flashed stockrom by brovonova....
same thing occurred to me
but in wipe option select data and repair partition
it will show fail to repair but don't worry
go to reboot and reboot recovery
you will able to mount data
just wipe it and reboot it
although u will loose u r all data in internal storage
abhishek biswas said:
my device was lucky i donot know but some how i am able to mount all the stuff from a hard reset means battery out in twrp and just restore to the back up which i had created i was very luck man there i know that a lot of people always failed to install stock rom via pc thats why i had not connected it at all now i am not going to tinker with my device at all i will stick to cm12.3 only
Click to expand...
Click to collapse
can you upload your system backup? It might work for me
plz help me i lost my micromax a311 its totally dead
ygdp tool error
CELL0: Initial backup YL-Parames Failed.
CELL0: error 4009
Related
I was flashing Custom ROM on my "Qmobile Noir A900" and ended up corrupting both ROM and recovery.
And my device is now stuck at a boot loop. Recovery mode is just a white screen and can't seem to go into bootloader mode either.
My Question is.. Is my device totally hard bricked or there's still some hope left?
I am new here and not sure if this is the right section. Sorry
Still no reply?
anAbbasi said:
Still no reply?
Click to expand...
Click to collapse
you can flash stock rom ,i think sold problem
download at http://www.needrom. com/mobile/purexperia-final-rom-for-elife-e3q-mobile-noir-a900/
tunglethanh90 said:
you can flash stock rom ,i think sold problem
Click to expand...
Click to collapse
How do I flash the stock ROM without having access to Recovery Mod and Bootloader MOD?
anAbbasi said:
How do I flash the stock ROM without having access to Recovery Mod and Bootloader MOD?
Click to expand...
Click to collapse
This MTK Chipset ,MTK MT6859
to flash stock rom witch MTK chip set you need
SP_Flash_Tool_5.1343.01.zip
MTK usb driver
Stock firmware
How to flash stock rom
Press and hold volume + ,device install driver port mtk driver
SP_Flash_Tool select scatterMTK...txt from stock firmware and star
Sorry i don't have device to test
tunglethanh90 said:
This MTK Chipset ,MTK MT6859
to flash stock rom witch MTK chip set you need
SP_Flash_Tool_5.1343.01.zip
MTK usb driver
Stock firmware
How to flash stock rom
Press and hold volume + ,device install driver port mtk driver
SP_Flash_Tool select scatterMTK...txt from stock firmware and star
Sorry i don't have device to test
Click to expand...
Click to collapse
Thanks a bunch mate. I did a little research on SP Flash Tool and MTK Chipsets.
I have Formatted whole device using Flash Tool. Now I am going to flash GM Discovery Stock ROM.
Will let you know how it goes.
tunglethanh90 said:
This MTK Chipset ,MTK MT6859
to flash stock rom witch MTK chip set you need
SP_Flash_Tool_5.1343.01.zip
MTK usb driver
Stock firmware
How to flash stock rom
Press and hold volume + ,device install driver port mtk driver
SP_Flash_Tool select scatterMTK...txt from stock firmware and star
Sorry i don't have device to test
Click to expand...
Click to collapse
Well that didn't workout so well. I am unable to FLASH new ROM. I keep getting
BROM ERROR: S_FT_ENABLE_FAIL (4032)
[EMI] Enable DRAM Failed!
Can you suggest any solution for this?
I think I will now try Blu Life Play ROM.
anAbbasi said:
Well that didn't workout so well. I am unable to FLASH new ROM. I keep getting
BROM ERROR: S_FT_ENABLE_FAIL (4032)
[EMI] Enable DRAM Failed!
Can you suggest any solution for this?
I think I will now try Blu Life Play ROM.
Click to expand...
Click to collapse
Rom wrong or please use SP_Flash_Tool_5.1343.01 and select firmware upgrage
tunglethanh90 said:
Rom wrong or please use SP_Flash_Tool_5.1343.01 and select firmware upgrage
Click to expand...
Click to collapse
No luck.
Tried SPFT 5.1352.01.
Used Firmware Upgrade.
still same error.
Used the ROM from this link this time.
http://forum.xda-developers.com/showpost.php?p=43772181&postcount=2
Maybe it's because I formatted whole flash?
anAbbasi said:
No luck.
Tried SPFT 5.1352.01.
Used Firmware Upgrade.
still same error.
Used the ROM from this link this time.
http://forum.xda-developers.com/showpost.php?p=43772181&postcount=2
Maybe it's because I formatted whole flash?
Click to expand...
Click to collapse
Try with here
Select firmware upgrade
Post result
tunglethanh90 said:
Try with here
Select firmware upgrade
Post result
Click to expand...
Click to collapse
Used SP Flash Tool 5.1343.01 this time. (The one you provided)
Same error as before.
I have attached screenshots of the procedure.
Snap1: Files I am flashing.
Snap2: when I connect my device.
Snap3: the error I receive.
And Also, If I use the scatter file for without Preloader, Flash tool crashes after red bar fills.
anAbbasi said:
Used SP Flash Tool 5.1343.01 this time. (The one you provided)
Same error as before.
I have attached screenshots of the procedure.
Snap1: Files I am flashing.
Snap2: when I connect my device.
Snap3: the error I receive.
And Also, If I use the scatter file for without Preloader, Flash tool crashes after red bar fills.
Click to expand...
Click to collapse
Try Flash file http://www.mediafire.com/download/d8ccqumthn9fvbb/A900_140428_103304.rar
tunglethanh90 said:
Try Flash file http://www.mediafire.com/download/d8ccqumthn9fvbb/A900_140428_103304.rar
Click to expand...
Click to collapse
Downloading now. What's different about this file.
P.S. I also tried flashing GIONEE ELIFE E3 stock rom. Same error.
anAbbasi said:
Downloading now. What's different about this file.
P.S. I also tried flashing GIONEE ELIFE E3 stock rom. Same error.
Click to expand...
Click to collapse
you download and flash firmware ,post result
tunglethanh90 said:
you download and flash firmware ,post result
Click to expand...
Click to collapse
Did that...
Device is back on... all thanks to you...
I am now facing two new issues.
1. SIM cards are not being recognized.
2. Secondly, Internal Storage is not accessible.
File Explorer only shows sdcard and Upon connecting to PC, only sdcard is visible. However, I can see internal storage listed in Settings > Storage.
anAbbasi said:
Did that...
Device is back on... all thanks to you...
I am now facing two new issues.
1. SIM cards are not being recognized.
2. Secondly, Internal Storage is not accessible.
File Explorer only shows sdcard and Upon connecting to PC, only sdcard is visible. However, I can see internal storage listed in Settings > Storage.
Click to expand...
Click to collapse
Try Hard reset
tunglethanh90 said:
you download and flash firmware ,post result
Click to expand...
Click to collapse
Solved these issues too.
First did a cache wipe and factory reset. It solved the storage problem but gave me invalid IMEI notification.
Then did a backup restore from default recovery. (I had made a backup prior to all this )
Solved everything.
Thanks a lot man. You saved the day!
anAbbasi said:
Solved these issues too.
First did a cache wipe and factory reset. It solved the storage problem but gave me invalid IMEI notification.
Then did a backup restore from default recovery. (I had made a backup prior to all this )
Solved everything.
Thanks a lot man. You saved the day!
Click to expand...
Click to collapse
Ok , Thks
By the way, where did you get that Backup from?
tunglethanh90 said:
Try Flash file http://www.mediafire.com/download/d8ccqumthn9fvbb/A900_140428_103304.rar
Click to expand...
Click to collapse
Hey,
Though this thread is old and dead now, but i must thank tunglethanh90 for providing the stock Rom (spflash version) of A900. I was having problem with my A900 and found stock rom on needrom site, flashed it and my cell went in to bootloop. I didn't have SPFlash or MTK backup only CWM backup which was no good. I used this ROM provided by tunglethanh90 and i was successful in making my set alive again. Afterwards, i got the problem of invalid IMEI. For that i installed CWM recovery and restored my cwm stock rom backup that i took and saved ealier. All good now but making my set alive again is due to tunglethanh90. Thank You Sir .... So heads up for any guy having QMobile A900 Rom issue, this is what u need to download, dont dl from needrom as its no go.
Regards.
Hi Guys,
Can someone help me, please? I've rooted my P780, and installed ClockworkMod Recovery. I can't seem to get any ROMs to install, though. I've tried four now, two from the forums here and two from needrom.com, but none of them install.
I put the ROM zip file on the SD card, reboot to CWM, wipe etc then try and install but for every ROM I get the following:
Warning: No file_contentssymlink: some symlinks failed
E: Error in <ROM zip file> (Status 7)
Is there something more I have to do? Or should I try and flash by other means?
Thanks!
GlumReaper said:
Hi Guys,
Can someone help me, please? I've rooted my P780, and installed ClockworkMod Recovery. I can't seem to get any ROMs to install, though. I've tried four now, two from the forums here and two from needrom.com, but none of them install.
I put the ROM zip file on the SD card, reboot to CWM, wipe etc then try and install but for every ROM I get the following:
Warning: No file_contentssymlink: some symlinks failed
E: Error in <ROM zip file> (Status 7)
Is there something more I have to do? Or should I try and flash by other means?
Thanks!
Click to expand...
Click to collapse
Flash TWRP 2.7.1.1 and try again!
Tell me if you get any errors !
¬
stympy said:
Flash TWRP 2.7.1.1 and try again!
Click to expand...
Click to collapse
Thanks for the reply Stympy. I was looking at this myself, having found this thread:
http://forum.xda-developers.com/lenovo-p780/development/rom-lenovo-p780-pre-rooted-official-t2553725
And your helpful thread here:
http://forum.xda-developers.com/lenovo-p780/help/rooting-tutorial-kitkat-t2835605
I'll give it a go. It might be tricky because I have 64 bit and couldn't initially get the drivers working. I'll keep trying though!
GlumReaper said:
Thanks for the reply Stympy. I was looking at this myself, having found this thread:
http://forum.xda-developers.com/lenovo-p780/development/rom-lenovo-p780-pre-rooted-official-t2553725
And your helpful thread here:
http://forum.xda-developers.com/lenovo-p780/help/rooting-tutorial-kitkat-t2835605
I'll give it a go. It might be tricky because I have 64 bit and couldn't initially get the drivers working. I'll keep trying though!
Click to expand...
Click to collapse
Iff your phone is rooted do this:
Download TWRP 2.7.1.1 from my post and install Mobileuncle Tools from Magazin Play!
Extract TWRP from archive rename it recovery.img and copy on your internal memory, in the root of your internal memory not in one folder.
Open Mobileuncle Tool and go to Recovery Update>and the first option select and flash. Then restart directly to recovery. Not optional!
Try this!
Waiting for feedback.
Sadly, I'm still having problems.
I booted up the stock ROM (had to try and get it back off Chinese! :laugh: )
I reinstalled Framaroot, rooted and then used MobileUncle tools to install the recovery.img from your TWRP zip as suggested. This has worked, I now have TWRP as recovery, which is good, thanks.
However, when I try and install a ROM from ZIP - just tried an AOSP and an SLXROM - I get the same thing:
Code:
symlink: some symlinks failed
Error executing undater binary in zip '/external_sd/SLXROM)v26-Lenovo_P780-ROW.zip'
Any more help would be greatly appreciated.
GlumReaper said:
Sadly, I'm still having problems.
I booted up the stock ROM (had to try and get it back off Chinese! :laugh: )
I reinstalled Framaroot, rooted and then used MobileUncle tools to install the recovery.img from your TWRP zip as suggested. This has worked, I now have TWRP as recovery, which is good, thanks.
However, when I try and install a ROM from ZIP - just tried an AOSP and an SLXROM - I get the same thing:
Code:
symlink: some symlinks failed
Error executing undater binary in zip '/external_sd/SLXROM)v26-Lenovo_P780-ROW.zip'
Any more help would be greatly appreciated.
Click to expand...
Click to collapse
Ok. It seems to me that you have problems with the archives, maybe i am wrong. Try to see if the archives are not corrupted by something.
Try first to replace your SD Card just for test, and try to reflash SLX or AOSP again.
One more thing: be careful when you download the archives not to be corrupted.
Sent from my Lenovo P780
It's still not working for me
I've taken the SD card from my older phone, which has been working fine for years. Formatted it and reloaded ROMS, but I still get exactly the same thing. I've tried five different ROMS, which were downloaded across two different computers at home and one in work on a different connection, so I can't imagine that all of these files would suffer the same corruption.
I've been having a search around and did find one person suggesting that it might be to do with storage space. I think I've seen in this forum (but I can't find it now) that you can resize the system storage partitions. Do I need to try this?
Thanks for your continuing help!
Partitioning didn't seem to help.
I followed the instructions in this thread:
http://forum.xda-developers.com/lenovo-p780/general/p780-repartition-storage-t2668744
But I still get the same thing when I try to install a ROM from SD Card. :crying:
I feel sure there's something really simple that I've missed, but even re-reading all the threads I can't figure it out.
GlumReaper said:
Partitioning didn't seem to help.
I followed the instructions in this thread:
http://forum.xda-developers.com/lenovo-p780/general/p780-repartition-storage-t2668744
But I still get the same thing when I try to install a ROM from SD Card. :crying:
I feel sure there's something really simple that I've missed, but even re-reading all the threads I can't figure it out.
Click to expand...
Click to collapse
Hi. Tell me what is your partitioning?
stympy said:
Hi. Tell me what is your partitioning?
Click to expand...
Click to collapse
I used the 'recommended' option in the ReParted/Aroma tool.
Now in the stock OS I can see:
Internal Storage:
2.56GB total
1.33GB available
USB Storage:
1.03GB total
1.02GB available
And then my 16GB SD card as well.
Well, I think I broke it. :crying:
Out of desperation and thinking I might have got the wrong idea, I tried a china, not ROW rom. Strangely, TWRP seemed to be able to install this. However, now the phone won't boot. So I have no OS at all!
I can still load TWRP recovery, but it still won't install roms. Also it keeps telling me it can't mount /data for some reason.
Can anyone help, please? What have I done?
This sounds like me ... the first 24 hours i had my p780. After that i discovered i have a newer version (also Chinese) of the phone then most of the forum members. I can only flash through the flashtools (i don't even bother to install a custom recovery anymore). You need an other preloader.
So just try it ( you got nothing to loose anyway )
Download the flashtool if you didn't do that already .
Make sure you have the correct drivers installed
Download a rom you can flash with the flashtool (i'm using a modified version of VibeUi2.0 no Chinese apps, and extra languages )
replace the preloader in the rom with the one attached.
shutoff your phone.
load the rom in the flashtool (make sure you've selected everything you need like DL with checksum etc, if you never did it please read threads and topics)
press download and connect your phone ...
for me all this above resurrected my phone again
Re-Mi said:
This sounds like me ... the first 24 hours i had my p780. After that i discovered i have a newer version (also Chinese) of the phone then most of the forum members. I can only flash through the flashtools (i don't even bother to install a custom recovery anymore). You need an other preloader.
So just try it ( you got nothing to loose anyway )
Click to expand...
Click to collapse
Thanks for your reply Re-Mi! It gives me hope to know you got yours sorted. I'll definitely try your suggestion.
I'm just wondering, how do I use the flash tool? All the tutorials I've seen have needed the phone to be on and have usb debugging on. But I don't have a working OS for this, only TWRP recovery works now. Is that what the preloader is for? I shall research!
Again, thanks.
GlumReaper said:
Thanks for your reply Re-Mi! It gives me hope to know you got yours sorted. I'll definitely try your suggestion.
I'm just wondering, how do I use the flash tool? All the tutorials I've seen have needed the phone to be on and have usb debugging on. But I don't have a working OS for this, only TWRP recovery works now. Is that what the preloader is for? I shall research!
Again, thanks.
Click to expand...
Click to collapse
Step by step guide :
If your phone is not already soft bricked, back up whatever you want. External SD card is fine. If your phone is soft-brick then say goodbye to your data and skip this step.
Uncompress all the files you downloaded from this thread into a directory where you can remember. Including the ROMs.
Shutdown your phone if its not in a bootloop. If it is skip this step.
Open "Device Manager" on your Windows PC.
Plug in your phone through the micro USB cable. A device will show up for a few seconds in "Device Manager". After that, it will disappear again!
Recognize the device tree where it appeared, and wait for it as you unplug and plug in your phone again (if bootloop, its automatic!)
Catch it with a right click as it appears! Then choose "Update Drivers" and pick the directory where you uncompressed the drivers you downloaded above. Its ok if after catching it the device disconnects. You only need to install the drivers now.
Assuming the drivers are correctly installed, run the Smart Phone Flash Tool.
Click on scatter-loading and choose the scatter file "MT6589_Android_scatter_emmc.txt" of the ROM you want to flash.
Make sure the checkbox "DL DA All With Check Sum" is CHECKED
Click on "Firmware->Upgrade" button.
Plug in your powered down phone via the USB cable again. See it flash.
When a big green circle appears on the screen, your are done!
Source
Woohoo! Got my phone working!
Thanks for your help guys. In the end I borrowed a laptop that had windows 7 on, which I was able to get the flash tool working on. So I've now flashed with the kitkat version of the stock ROM
I still don't know why TWRP wouldn't flash any one of the eight different ROMs I tried!
I'm going to continue messing about with the phone. I'd like to get Life ROM working, but I need TWRP back first.
Again, thanks all.
First of all , ihave to say , iam no GURU.
But since not many work on it and cuoco92 seems to be busy at the moment..
Ive had the phone for a year or so and have dealt with most problems that appear..
so pls feel free to ask and ill try to answer.
Any thanks will be appreciated..
there is an upload on my dropbox for the needed tools..will post as soon as it finishes
https://www.dropbox.com/sh/wy8tn4xzfkpi9hn/AACRsiI3RsmTpshwi8aG4Gx5a?dl=0
Spflash tool :working
Lewa rom for spflash:working
Appropriate drivers
Low internal memory after upgrading to MIUI 5.7
After upgrading to the latest MIUI update, the internal memory doesn't seems to be detected properly. I have more that 5 GB left, however it shows that I have 0KB left out of 6.3 MB. I am unable to access my old photos and videos. Whatapp doesn't work properly.
Any solution on how to fix the low internal memory issue on MIUI rom?
anilkm003 said:
After upgrading to the latest MIUI update, the internal memory doesn't seems to be detected properly. I have more that 5 GB left, however it shows that I have 0KB left out of 6.3 MB. I am unable to access my old photos and videos. Whatapp doesn't work properly.
Any solution on how to fix the low internal memory issue on MIUI rom?
Click to expand...
Click to collapse
does the miui work correctly?plz give some link so i can look into it.some screenshot of you phone data if you can.i guess the error is into the partitioning
Sent from my 6043D using XDA Free mobile app
hi sir, i have an error on TWRP i tried installing diff. versions of Recovery on it using Mobile uncle but i cant seem to fix it, im getting "unable to mount " so i am unable full wipe the phone, im guessing i need to reflash the stock rom using spflashtool but i searched everything on the net i cant det stock rom and working walkthrough and working files. any help would be appreciated thank u so much
The official rom is unavailable.
You can find another rom to install through the tools. But it has to be in the right format.i wouldn't change the recovery through mobile uncle. I would recommend changing it through appropriate tool. I'll be uploading a dropbox file with a rom you can use. Wait till tomorrow and you'll be ok.
Sent from my 6043D
Stuff uploaded.
Sent from my 6043D
anilkm003 said:
After upgrading to the latest MIUI update, the internal memory doesn't seems to be detected properly. I have more that 5 GB left, however it shows that I have 0KB left out of 6.3 MB. I am unable to access my old photos and videos. Whatapp doesn't work properly.
Any solution on how to fix the low internal memory issue on MIUI rom?
Click to expand...
Click to collapse
you updated through recovery??
Sent from my 6043D
Thanks bro for uploading files and please bro can you write step by step that how to use sp flash tools....please its emergency reply soon...am waiting ...and I only want to install twrp so please tell me how to install twrp with sp flash tools and one more thing that when I plug usb in pc and mobile it stucks on boot loop so can I use sp tools while in bootlop or I have to remove battery by teradown phone
hi Sir, thanks for uploading helpful files. ill try to flash them today - crossed finger - ill try to flash twrp 1st using spflashtool ill update you for any progress thank you
shubhamx01 said:
Thanks bro for uploading files and please bro can you write step by step that how to use sp flash tools....please its emergency reply soon...am waiting ...and I only want to install twrp so please tell me how to install twrp with sp flash tools and one more thing that when I plug usb in pc and mobile it stucks on boot loop so can I use sp tools while in bootlop or I have to remove battery by teradown phone[/QUOTE
you can get into the bootloader by key combination.to tell you the truth since its always booting up if you keep the up(i think) volume button pressed it will eventually get into recovery.
anyway the sp flash tools is quite easy..just add the scatter file that is provided in my DB and open the rom
all things will go to their appropriate places.the rom works 100%
i used it for a few days until i found my cuoco92 backup (which i like more)
keep me in the loop if something happens
Click to expand...
Click to collapse
Bro sorry am little weak in english and did you mean that should I use sp tools while in recovery or I can use it in while in bootloop??and I am unable to go in bootloader can you give me key combinations ....and I also have custom recovery and aroma manager but I am unable to use otg cable is there any other mathod where is transfer rom into phone and brother you are so helpfull bro may god bless you because in nowdays no one helps others but you are awesome bro thanks very much
i meant using it in bootloop..in the drivers i uploaded there is a driver that you can use even in bootloop and the phone gets recognised as a proper usb device.then sp flash can work fine.if i remember correctly the driver is called bootloader driver
Sent from my 6043D
Bro today I try to install twrp using spflash tools and at down where installing procees ...there I saw procces completes and this is written in red coluur and a message appear that vrom need to install properly what's wrong with that and when I tried to go in recovery there was no twrp please tell me my mistake or I have to download rom to install with flashtools.....and one more thing please how to install drivers propery because I can't found install options in driver rar or extrttact it and driver will install automatically........and please bro last thing can you give me your facebook I'd so I can tell you my problem anytime because I have not pc at home and I have to go city to use pc so please reply as soon as possible
I'll upload a text file with guide
Sent from my 6043D
Thanks bro upload file asap
anilkm003 said:
After upgrading to the latest MIUI update, the internal memory doesn't seems to be detected properly. I have more that 5 GB left, however it shows that I have 0KB left out of 6.3 MB. I am unable to access my old photos and videos. Whatapp doesn't work properly.
Any solution on how to fix the low internal memory issue on MIUI rom?
Click to expand...
Click to collapse
I had the same problem. Seems that the ROM is not recognising all the "virtual" sdcard that we have in our mobile phone.
Anybody knows how to solve it?
Bro I format my whoke flash with sp flash tools and now my phone doesnot booting and not showing anything but carging led in working when coNnecting to charger......now sp flashtools not detecting my phone please tell me how to detect phone with flash tools is ....is I need new drivers or what please help me
Bro I flashed twrp with flash tools suceesfully and when I try to flash rom with twrp I get error like unable to mount data and unable to mount internal storage and i also check internal memory with file manager in twrp but it shows 0 mb internal memory......please please please reply bro please please tell me how to fix it bro please reply at least once
shubhamx01 said:
Bro I flashed twrp with flash tools suceesfully and when I try to flash rom with twrp I get error like unable to mount data and unable to mount internal storage and i also check internal memory with file manager in twrp but it shows 0 mb internal memory......please please please reply bro please please tell me how to fix it bro please reply at least once
Click to expand...
Click to collapse
I think it will be better if you try to install the ROM using Flash Tool instead of TWRP.
Do you have the stock one?
I have TWRP in my A310. Flashed http://forum.xda-developers.com/a310/development/resurrection-remix-lp-5-5-t3160496 this rom, dunno which version TWRP I have, so now phone is not starting up.
Any help will be appreciated, Guys I don't want to take my phone to Service center ppl. They are horrible.
Phone is turning on, trying to boot - failing - restarting - trying to enter recovery as a TWRP logo shows up then screen flickers and nothing happens and this keeps going on. TWRP also tries to open MTP but that fails too.
Dosen't stay in Bootloader - fastboot as well, restarts.
Are you able to go to recovery?
Do you have a backup of previous rom? If you have it, try flashing stock rom using ygdp tool and after that restore the backup.
Thanks for quick reply
shaijuvjohn said:
Are you able to go to recovery?
Do you have a backup of previous rom? If you have it, try flashing stock rom using ygdp tool and after that restore the backup.
Click to expand...
Click to collapse
No, I am not able to go to recovery.
A quick question to those who have used YGDP, Does it work while is switched off ?
headlessNick said:
No, I am not able to go to recovery.
A quick question to those who have used YGDP, Does it work while is switched off ?
Click to expand...
Click to collapse
Do you have the backup of previous rom?
If you are going to flash stock rom, gydp tool will detect the phone even without battery too.
shaijuvjohn said:
Do you have the backup of previous rom?
If you are going to flash stock rom, gydp tool will detect the phone even without battery too.
Click to expand...
Click to collapse
Let me check that when I get back home and let you know, I must have backups If GYDY worked, then we shall party :angel::cyclops::highfive:
Can someone point to a GYDP guide, I found one but the download links don't work :cyclops:
headlessNick said:
Let me check that when I get back home and let you know, I must have backups If GYDY worked, then we shall party :angel::cyclops::highfive:
Click to expand...
Click to collapse
Try YGDP and flash stock and then restore the backup if available.
When you flash the stock rom it will repalce the twrp also. We can easily install twrp through ygdp. Follow the steps.
1. Select your .cpb file and apply
2. YGDP will unzip the cpb file, path may be C:\YLXZGJ\YGDP\DownFiles\8297W (in my system this is the path, please check after unzipping)
3. Check the unzipped folder contents
4. There will be a file named recovery.img
5. Delete the recovery.img file
6. Copy your twrp recovery to the unzipped folder and rename it to recovery.img
7. Click on start button
8. Remove battery from your phone and connect it to the usb
9. It will detect your phone and start flashing
10. Wait for flashing finishes to 100 %
11. Done. Disconnect phone. You flashed stock rom with twrp recovery
12. Copy the backup to memory card and insert it in phone
12. Insert battery and press power button and volume up key, go to twrp recovery, restore your backup and enjoy
---------- Post added at 12:00 PM ---------- Previous post was at 11:56 AM ----------
headlessNick said:
Can someone point to a GYDP guide, I found one but the download links don't work :cyclops:
Click to expand...
Click to collapse
http://www.needrom.com/wp-content/uploads/2014/10/YGDP_Setup_V3.83_Assembly.zip
Try this one, i am using this one on A311.
You need to have these drivers installed in your system - DA USB VCOM Port, PreLoader USB VCOM (Android)
If you have drivers not installed use the below one from the attachment. :victory:
Thanks - Tying...
headlessNick said:
Thanks - Tying...
Click to expand...
Click to collapse
Thanks a lot guys especially
shaijuvjohn said:
shaijuvjohn
Click to expand...
Click to collapse
, I should have probably read all the instructions, It was all there. Had some difficulties in installing the drivers as COM port But at the end :victory: works like charm.
I will definitely spread this knowledge with who ever needs in future.
Proud owner of stocked rooted custom recovery MMX Nitro A310 and OnePlus One
headlessNick said:
Thanks a lot guys especially , I should have probably read all the instructions, It was all there. Had some difficulties in installing the drivers as COM port But at the end :victory: works like charm.
I will definitely spread this knowledge with who ever needs in future.
Proud owner of stocked rooted custom recovery MMX Nitro A310 and OnePlus One
Click to expand...
Click to collapse
Yup because i already went through all these situations and i know the difficulties. That is why i gave you each steps. Always Happy to HELP. :victory:
didnt worked
shaijuvjohn said:
Are you able to go to recovery?
Do you have a backup of previous rom? If you have it, try flashing stock rom using ygdp tool and after that restore the backup.
Click to expand...
Click to collapse
I hv tried to installed from ygdp stock rom but it stopped in between. The process wont complete, plz help me if u can
Micromax q391
My Micromax canvas q391 not working its just stuck on the Micromax logo n I'm not even able to access the recovery mode n does not have the backup of rom
What can I do to start it up please help
Even I tried to Flash with YGDP but no use. My mobile is not stable suddenly and automatically it disconnects from my system even connected with USB Cable.
..
WHen I open the link a page comes up saying " Needrom do not authorizing, the links referred by another website for download the ROMs.
The link must obligatory be clicked from of Needrom.com
"
What should I do....
same problrm faced
headlessNick said:
I have TWRP in my A310. Flashed http://forum.xda-developers.com/a310/development/resurrection-remix-lp-5-5-t3160496 this rom, dunno which version TWRP I have, so now phone is not starting up.
Any help will be appreciated, Guys I don't want to take my phone to Service center ppl. They are horrible.
Phone is turning on, trying to boot - failing - restarting - trying to enter recovery as a TWRP logo shows up then screen flickers and nothing happens and this keeps going on. TWRP also tries to open MTP but that fails too.
Dosen't stay in Bootloader - fastboot as well, restarts.
Click to expand...
Click to collapse
i had faced same problem ..
but stay calm .. just download ypdp flash tool .. download stock rom and flash it using ypdp tool ... remember while flashing remove the battery otherwise it will not detect the phone , as my was not detected .. but as soon i removed the battery , it flashed the rom in couple of minutes . and after flashing remember to flash a custom rom as the stock rom gets corrupted causing these issues .. installed darkeness redefined rom and it is woking extremely fast , best rom in my opinion . choise is upon you ,
Hope my message helped you , for any more questions do ask.
boot loop
i have the same problem boot loop but im not able to flash becoz my micromax canvas nitro a311 disconnecting continuously on lap im not able to open recovery mode also help:fingers-crossed:
I have been trying to flash a Micromax Canvas HD A116 stock rom on my phone that went dead all of a sudden 1 day. I do not know what the reason was. I tried all the stock roms from v1 to v5. I also tried SPFT v3.something and also SPFT v5.something. My phone gets detected very well on my laptop and on my PC both with Windows 7 and Windows 10 respectively. Every time I have tried to flash the stock rom, it gives error 5069 no space. I have gone through lots of forums online with regards to this topic. However, there is no concrete solution that i could find anywhere. A few reasons that i could find behind this error are emmc crash, larger rom file size, nand flash could not be detected and partition overlap. I do not know what all these mean except larger rom file size. Anyways, i have used all the stock rom files available for my mmx a116. Any help will be highly appreciated. Also to let u know, I'm a newbee trying to learn everything. Thank you in advance.
maniche0201 said:
I have been trying to flash a Micromax Canvas HD A116 stock rom on my phone that went dead all of a sudden 1 day. I do not know what the reason was. I tried all the stock roms from v1 to v5. I also tried SPFT v3.something and also SPFT v5.something. My phone gets detected very well on my laptop and on my PC both with Windows 7 and Windows 10 respectively. Every time I have tried to flash the stock rom, it gives error 5069 no space. I have gone through lots of forums online with regards to this topic. However, there is no concrete solution that i could find anywhere. A few reasons that i could find behind this error are emmc crash, larger rom file size, nand flash could not be detected and partition overlap. I do not know what all these mean except larger rom file size. Anyways, i have used all the stock rom files available for my mmx a116. Any help will be highly appreciated. Also to let u know, I'm a newbee trying to learn everything. Thank you in advance.
Click to expand...
Click to collapse
Do full wipe in recovery then flash stock rom
Firstly, thank you for answering my question Abdul. What is the meaning of do a full wipe in recovery and then flashing the stock rom? I'm using SP Flash Tool to flash the stock rom and my phone is totally dead. It only gets detected in my laptop because I have installed the correct drivers while flashing it. But end up in error 5069.
maniche0201 said:
Firstly, thank you for answering my question Abdul. What is the meaning of do a full wipe in recovery and then flashing the stock rom? I'm using SP Flash Tool to flash the stock rom and my phone is totally dead. It only gets detected in my laptop because I have installed the correct drivers while flashing it. But end up in error 5069.
Click to expand...
Click to collapse
Welcome
Happpy TO help
I mean to say that Clear Cache And reset from recovery if recovery is still open before flashing stock from sp tool
The phone is totally dead. It doesnt even go into recovery. If it could have loaded recovery, i would have easily flashed the rom. Have you understood my situation completely?
Hello,
Did you solve your problem?
I have exactly the same with my phone: Brom Error 5069.
Thank you.
maniche0201 said:
Firstly, thank you for answering my question Abdul. What is the meaning of do a full wipe in recovery and then flashing the stock rom? I'm using SP Flash Tool to flash the stock rom and my phone is totally dead. It only gets detected in my laptop because I have installed the correct drivers while flashing it. But end up in error 5069.
Click to expand...
Click to collapse
i am also facing same kind of problem with different error.....
can you please give me link for the drivers please.............. my phone is not even getting detected