Elephone p9000 wont charge - Elephone P9000 Questions & Answers

Just received my awaited elephone p9000 today and had been using it for a couple of hours setting up, Doing an update etc. When i came time to charge it. To sum it up it used the supplied usb c cable to attempt to charge it on multiple usb chargers and tried it with two pc's with no success. When connected to the pc it did come up with 'This device has been linked" Then immediately followed by "this device has been unplugged" Or at least something along those lines. Today i went and purchased a micro usb to usb c adapter and managed to get it to charge momentarily then to find it stop then start again. I am now sitting on 1% power and not sure what todo. Any advice? I have warranty on it from gearbest fyi.

octan_3 said:
Just received my awaited elephone p9000 today and had been using it for a couple of hours setting up, Doing an update etc. When i came time to charge it. To sum it up it used the supplied usb c cable to attempt to charge it on multiple usb chargers and tried it with two pc's with no success. When connected to the pc it did come up with 'This device has been linked" Then immediately followed by "this device has been unplugged" Or at least something along those lines. Today i went and purchased a micro usb to usb c adapter and managed to get it to charge momentarily then to find it stop then start again. I am now sitting on 1% power and not sure what todo. Any advice? I have warranty on it from gearbest fyi.
Click to expand...
Click to collapse
When I first charged my P9000 it did not go over 50% until I updated to the newest OTA and rebooted the device after the last update.
But I have not encountered disconnects or anything like that.
You could also screw your device apart and remove the battery for some time, but as you have a valid warranty I would not recommend that.

Kooperativ said:
When I first charged my P9000 it did not go over 50% until I updated to the newest OTA and rebooted the device after the last update.
But I have not encountered disconnects or anything like that.
You could also screw your device apart and remove the battery for some time, but as you have a valid warranty I would not recommend that.
Click to expand...
Click to collapse
Thanks for the response. I wish i could get to 50% battery. Im currently trying to update to the newest OTA but its difficult.

octan_3 said:
Thanks for the response. I wish i could get to 50% battery. Im currently trying to update to the newest OTA but its difficult.
Click to expand...
Click to collapse
If you connect your phone to your PC, is it listed in the device manager? If yes, does your PC recognize it as Elephone p9000?
Have you installed the latest drivers for your phone? (http://bbs.elephone.hk/thread-1037-1-1.html#.VWgkX_RAU-0)
Maybe changing the connection type in the notifications (when plugged in) helps in any way ?

Have you tried a different lead? I know this sounds obvious but my brother had a similar problem with his P9000 when he first got it, he used my lead (for some reason my lead was different to his as I bought from a different supplier, dunno why mines a kinda thick white lead, my brothers was a kinda thinner blue Elephone lead) and it worked fine. Although I haven't come across anyone else on here that's come across an issue with the supplied lead.

Kooperativ said:
If you connect your phone to your PC, is it listed in the device manager? If yes, does your PC recognize it as Elephone p9000?
Have you installed the latest drivers for your phone?
Maybe changing the connection type in the notifications (when plugged in) helps in any way ?
Click to expand...
Click to collapse
It does multiple things when it connects at different stages
ON and connected to pc- With elephone cable the phone constantly displays the messages 'Charger has been linked' and 'device has been unplugged' within ~1 sec of each other and no connection is noticed on PC.
With the MICRO USB - USB C adapter nothing happens
Powered off and connected to pc- Charging symbol will flash momentarily every ~5seconds. Pc will ding repeatedly as it connects and disconnects
fastboot- Somehow connects and is recognised by PC
Ive managed to get it past 30% power but took ages todo from leaving it powered off and just flashing on and off charging
jotei66 said:
Have you tried a different lead? I know this sounds obvious but my brother had a similar problem with his P9000 when he first got it, he used my lead (for some reason my lead was different to his as I bought from a different supplier, dunno why mines a kinda thick white lead, my brothers was a kinda thinner blue Elephone lead) and it worked fine. Although I haven't come across anyone else on here that's come across an issue with the supplied lead.
Click to expand...
Click to collapse
I only have 2 leads unfortunately. The stock elephone and a micro usb to usb c adapter with a working micro usb attached. Ive ordered some more online and waiting their arrival. Im stuck on what todo

That is indeed very strange.
You could try to flash TWRP 3.0.2.1 via fastboot (http://en.miui.com/thread-58623-1-1.html, just use the TWRP for Elephone P9000 instead), but I would not recommend that as your connection is really unstable. The chance of bricking your device is much higher than the chance that your problem is solved.
If the leads you ordered do not help you should get it replaced.

Related

Photon won't charge, reboots, no USB

Well, at just 3 weeks my Photon is dying and will be exchanged this morning. The problems started today when the phone started rebooting on its own several times. When I plug in the charger it doesn't charge at all and when I plug into a USB port I get no indication on the phone and Windows report an unrecognized device. I do have the correct drivers installed and all worked well earlier. I've tried several chargers to no avail. Off to Sprint in the morning! If anyone has any tips on this issue I'm all ears!
newalker91 said:
Have you used RSDLite to flash the CM5 SBF? I've seen this issue on phones that arent updated properly.
Click to expand...
Click to collapse
I did the OTA update and it worked fine for a few days and I thought about redoing it with RSDLite but, as I mentioned, I have no USB connection now so I can't connect to a PC and, even if I could, the battery is almost dead and can't be charged through the USB port. So I appear to be stuck for now even if I could charge the battery externally. I called Sprint and they authorized an exchange so I think that's probably my only option unless they can fix it while I wait.
looks like a bad micro usb port case.
double post

[Q] No charge, No MTP initialize, zero USB activity

Hey guys, thanks for dropping by.
I have a very wierd problem, that I just cant figure out.
It all started the other day, when I found my tablet dead after having been left on and charging during the night. The tab was dead, and I feared the worst. After having left it on what seems to me like a trickle charge for several hours, I managed to get it up and running, and the tab seems fine, it was just completely out of juice.
But my troubles are not over. Whenever I'd connect the tab to the wall charger, I'd only get the red "X" symbol in the corner, and it would say MTP Initialize, even though its plugged into the standard OEM wall charger that comes with.
When I connect the tablet to my computer using the same cable, nothing happens, and by that I mean nothing. Computer doesn't start the connection process at all, its not recognized in the device manager, nothing. Not even Odin can see the tablet when I put it in download mode, the tab keeps saying "Waitting USB Cable..."
Tried this on 2 computers, still no luck, even using a USB plug on the motherboard instead of front-usb.
Now, the tablet will "trickle charge" from both the wall charger, and the computer, but nothing else happens.
I figured it could've been the ROM, so I got the latest ICS Kanang ROM downloaded, transferred it to my tab using Bluetooth, and flashed this without hassle, but the problem still persists, only now showing a regular charge icon in the lower right section, but it is still only trickle charging as far as I can tell.
All I can figure is a defective USB cable, or even worse, defective port on the tablet itself, but I'm not sure. I've ordered a new cable from DealExtreme, that will hopefully arrive sooner rather than later.
But seeing as the tab is hardly 4-5 weeks old, I find it difficult to believe the cable is the problem.
Anyone have any ideas? I'm all out at this point, so any pointers is very appreciated. Thanks.
It could be the cable. It's the part you have used in each situation. I'd wait for the cable to arrive and test it with the tablet when you get it.
Sent from my GT-P7510 using xda premium
Hey, thanks for the reply.
Yeah, I really really hope this is the case, time will tell, DealExtreme is not the quickest dealer. I'll update when I get it.
The new cable came from DX, but I'm afraid it showed no difference on anything.
The cable is working just as the original one, so that's not the problem.
Anyone have any ideas?
I guess my main goal at the moment is flashing it back to stock and un-rooting so I can get it repaired.
You mind posting a screenshot, it's kinda hard to imagine what you see by what you read For all I know my imagination went from a red X to the corner to something like an X off battousai's face.
Then again, I'd be glad to help, provided you post screenies, would be a major help
Ah, yes, I will take screenshots of anything you want to see.
Right now im on ICS preview, and these are some snapshots WITH the cable connected.
The red "X" I'm talking about you can see on the first picture on the charging icon, this happened even when the wall charger was connected on gingerbread/overcome experience rom.
The other pictures you can see it says discharging. Now, this was taken when connected to the computer, and I guess that's normal, but it also happens exactly the same when connected to the wall charger that came with the unit.
If you want screenshots of anything else, ill get it asap!
I took a poorly image of the tab connected via USB, to my computer with Odin open, hopefully you can see what it says.
If not its just what happens, I don't get further.
By the screenshots, Is the language Swedish?
Then again thanks for providing the screenies
In your first screenshot that could be part of the theme, or was it never there previously? I don't really know if it's not charging or that's supposed to be the charging icon, because for some odd reason on ICS preview I don't see that red icon anywhere.
As for the tablet, the reason why you aren't detecting it seems as though you don't have the drivers on the PC, I don't know if you installed them or you didn't mention it because I never found it being mentioned in your reply. I know it sounds silly but the same thing happened to me when I was using the tablet, (originally my 3G series belonged to my dad who knew nothing about modding so he just gave it to me and said, "do your thing" ) He did also forget to mention that you require to have the drivers to detect it via Device Manager and MTP in general, shortly the COM port will show up aswell. Perhaps re-installing the drivers should do the trick?
Made me wonder how did you install ICS in the first place if you weren't able to have it read? But I realized you could have downloaded the zip file via the tablet, On another note, how did you install CWM in the first place? o.o
Hehe, almost! Its in Norwegian on the honeycomb picture.
The red "X" would show up whenever i was connected to the PC via USB, to indicate its not charging. It will however "trickle" charge, and take 24h to charge fully with no usage and turned off.
Yes, the red icon is not on ICS, it just says not charging in the about page, as you can see from the screenshot.
Drivers have been reinstalled two or three times on two different PC's, I don't believe this is the issue.
When I bought the unit, it was working 100%
USB was okay, I flashed and rooted the unit over to "Overcome Experience".
From there I transferred ICS preview via Bluetooth and installed that way.
Have you tried factory reset to make sure all modules are reset? Maybe the USB charge module in Overcome is conflicting.
Yes.
Factory reset 3-4 times on the two different roms. I've reset everything I could find, without success.
Perhaps it has gone faulty with the tablet's plug in port, someone had the same issue although it was his wire that was at fault, it detects the charge via USB but not enough volt's to be detected by the PC, has it been grounded? Seem's more likely :| Might have to get it checked in your local center perhaps, It's how I mentioned that any metallic object is able to relay electricity despite being broken or not, you may have a broken pin for all I know :|
Hi,
I'm having exactly the same issue with my 1 month old tab 7+. I tested it using my bosses charge cable and there is no issue so I need to go to the service centre for a warranty replacement on the cable.
Hope you sort out your issue soon!
Thanks, but I don't think I have any other choice to deliver it to Samsung Europe as a payable service to get it fixed.
Purchased on a American store, and I doubt they'll take it back with flashed software.
I'm not sure really, I'll see what I end up doing. Its not the cable, that's for sure.

[Q] USB not recognizing PC or Docks, please help.

Yesterday I plugged my phone into my PC and went to set it to mount as mass storage but the USB connected notification wasn't there. The phone charged fine off the USB, just didn't see the PC.
I thought this may be a PC issue until going to use it on my HD Multimedia dock, phone wouldn't recognize the dock was attached. Then went and tried it in the car dock, same thing, phone charged but didn't go into cardock mode.
Also not sure if this is related but since then battery has been discharging quite quickly.
Please help.
Regards
Bruce.
Hi, did you use the original cable ?
I noticed that the cable from my galaxy S II didn't work with the razr droid !
Brahim93 said:
Hi, did you use the original cable ?
I noticed that the cable from my galaxy S II didn't work with the razr droid !
Click to expand...
Click to collapse
Yeah, i did use the original cable.
bigblueyeti said:
Yesterday I plugged my phone into my PC and went to set it to mount as mass storage but the USB connected notification wasn't there. The phone charged fine off the USB, just didn't see the PC.
I thought this may be a PC issue until going to use it on my HD Multimedia dock, phone wouldn't recognize the dock was attached. Then went and tried it in the car dock, same thing, phone charged but didn't go into cardock mode.
Also not sure if this is related but since then battery has been discharging quite quickly.
Please help.
Regards
Bruce.
Click to expand...
Click to collapse
This will probably solve ur problem:
Uninstall all motorola from PC
Reinstall motocast 1.29
Connect ur razr in every mode, and wait it reinstall the drivers.
Cheers
Thanks, but it's the phone that's not recognizing the usb cable is plugged in. I've tried it on three PCs and the darn thing will only charge, not give usb connection options.
Get a small paintbrush and a can of Dust-Off or other compressed-gas sprayer.
Hold the phone between your knees with the USB port up. Swirl the brush around inside the USB jack while blowing air into it at the same time.
Try it now.
Micro USB jacks have a very nasty habit of collecting pocket lint. It can prevent the cables/plugs on any device from making a solid electrical contact.
This will likely become a routine operation that you perform once a week or so.
You can buy micro-USB rubber plugs that protect a female jack from damage and dirt. You should try the usual places to find one; Amazon, DigiKey, Fry's, JameCo, etc.
If this doesn't get it, you may be looking at either replacing the jack (if you can un/solder very small things), or replacing the phone itself.
PS: If you have geeky friends who like pranks, get a high-powered magnifying glass and check for Scotch Tape on the USB jack contacts. I've done this to an obnoxious iPhone FanBoyz phone before. I confessed before his battery was completely dead...
bigblueyeti said:
Thanks, but it's the phone that's not recognizing the usb cable is plugged in. I've tried it on three PCs and the darn thing will only charge, not give usb connection options.
Click to expand...
Click to collapse
Connect it into back usb.
Sent from my XT910 using Tapatalk 2
Did anyone ever find a solution to this? I'm having the exact same issue, have tried clearing out the USB port, different cables and every port on my PC. It charges on connection but doesn't recognise that it is connected to a computer rather than a power port.
Any advice?
Mithre said:
Did anyone ever find a solution to this? I'm having the exact same issue, have tried clearing out the USB port, different cables and every port on my PC. It charges on connection but doesn't recognise that it is connected to a computer rather than a power port.
Any advice?
Click to expand...
Click to collapse
Are you on stock or custom rom ?
SAJdroid said:
Are you on stock or custom rom ?
Click to expand...
Click to collapse
Stock. I'm thinking of doing a factory reset as it has been freezing a lot recently and I suspect its a software issue, but I was hoping to do a proper backup first, however I lost root a while ago when I updated to ICS . I don't know if the freezing and not recognising computer could be two sides of the same issue?

Galaxy S4 won't charge.

Help! My Samsung Galaxy S4 won't charge or connect to a computer. I've tried different chargers, cables, plug in locations, car, 110, computer. There is no dirt. Connection is clean. I have a spare battery and both of them will charge on the battery charger. I have tried backed up roms. I have done a factory reset.
All of this and nothing helped. Am willing to try anything. Verizon is going to send me a refurb.
Help please.
Sent from my SCH-I545 using Tapatalk 4 Beta
Is there any indication of a connection being made? If not, you should just wait for the refurb. If you have rooted, I really doubt Verizon will honor the warranty on the broken phone. I wish you the best.
Sent from my SCH-I545 using xda app-developers app
sounds like contacts are on the phone side are damaged or the micro usb port is damaged.
Have you plugged into to a pc just to see if it can "see" the device and connect?
You stated it cannot connect to a pc, so i would suspect you have a bad micro usb port.
if you can connect, its not the port, and try taking an eraser and gently swabbing the contacts on the phone side.
also, make sure when you insert the battery there is an actual contact established. sometimes when pulling/pushing the battery in and out, those contacts sink further into the device and finally when you insert a batter the contact is very poor. you may need a tool or tweezer to just VERY, VERY GENTLY raise the contacts if they sunk in to far......but be careful not to pull too hard/much they can snap and you will probably void any warranty......
vwpiper said:
Help! My Samsung Galaxy S4 won't charge or connect to a computer. I've tried different chargers, cables, plug in locations, car, 110, computer. There is no dirt. Connection is clean. I have a spare battery and both of them will charge on the battery charger. I have tried backed up roms. I have done a factory reset.
All of this and nothing helped. Am willing to try anything. Verizon is going to send me a refurb.
Help please.
Sent from my SCH-I545 using Tapatalk 4 Beta
Click to expand...
Click to collapse
xander45 said:
sounds like contacts are on the phone side are damaged or the micro usb port is damaged.
Have you plugged into to a pc just to see if it can "see" the device and connect?
You stated it cannot connect to a pc, so i would suspect you have a bad micro usb port.
if you can connect, its not the port, and try taking an eraser and gently swabbing the contacts on the phone side.
also, make sure when you insert the battery there is an actual contact established. sometimes when pulling/pushing the battery in and out, those contacts sink further into the device and finally when you insert a batter the contact is very poor. you may need a tool or tweezer to just VERY, VERY GENTLY raise the contacts if they sunk in to far......but be careful not to pull too hard/much they can snap and you will probably void any warranty......
Click to expand...
Click to collapse
I am having the exact same problem. I have replaced the microUSB charging port on the phone and it still doesnt charge with the new port. I'm not sure what is going on. NEED HELP BIG TIME!!!
I'm having the same problem as well. It has been like that for bout a month or so now. I googled it and it seems to be a problem with the s3's and s4's. I'm not so worried about it as I have a spare battery charger and I have the wireless charging receiver on my s4 and it charges my phone just fine.
I had this exact problem I believe...tried several different chargers...everthing. Try turning the phone off and see if it takes a charge. When mine was off it would show a gray battery and vibrate every 5-10 seconds. I figured it was an issue with the charging/usb port but all of the sudden my phone started charging normally and is visible by a computer. Lasted for about 4 days and have been in the clear for about 3 days now. No clue what went wrong or why, but try what I mentioned above by charging with phone off for a half hour or so and see if it has charged at all. If you need a new USB port, not all GS4's have the same port, so you must get a verizon specific one (ebay). usually run about $20..or $65 installed at a phone fixing center. I didnt want to lose MDK, so I was prepared to just charge externally, but ended up not having to...yet
It happened to me also. I had some intermittent luck with blowing out the port with air from my air compressor. But in the end it just stopped working and Verizon sent me a refurbished one.
I Also have this problem!
PLEASE HELP!
I don't know why but my international galaxy s4 running cm 10.1.3 stable isn't charging...
I plug it in to the wall and nothing happens its as if the phone doesn't even know it's plugged in...
pcmaster44 said:
PLEASE HELP!
I don't know why but my international galaxy s4 running cm 10.1.3 stable isn't charging...
I plug it in to the wall and nothing happens its as if the phone doesn't even know it's plugged in...
Click to expand...
Click to collapse
Have you tried powering down your phone and seeing if that gray battery comes up and you get the vibrations (while plugged into charger)? You may need a new port, but since your under warranty, you could get a replacement unless you want to charge externally
S4 problem after update to 4.3
Hy,
I have a similar problem with my S4 (i9505), won't indicate if it is charging or connect to a computer, but while the charger is conected to S4, the battery level is increasing. When the battery is fully charged S4 is SHUTING DOWN!!!! And it wont start by pressing ON/OFF button, it will only start after I press Vol Down+Power, after goes to Download Mode and press Vol Down .
Tryed in many ways to fix:
- restore-
- hard reset
- changed te battery and charger
-i\ve changed even the usb port (flex cable) and =no results...
All problem started after update to 4.3.... and it is not an isolated case too many people complains about this 'awesome smartphone' with 'awesome issues' .
So, if anyone have any ideea how to solve this issues....
{Sorry for my bad english}
Had the same problem...lasted for about a day, I had to take a dry q-tip and clean the charger and the port where the phone charges and was able to get it working again. If you are rooted and are having issues go to amazon or ebay and get a wireless charger and it should take care of your problems as well
templton said:
Had the same problem...lasted for about a day, I had to take a dry q-tip and clean the charger and the port where the phone charges and was able to get it working again. If you are rooted and are having issues go to amazon or ebay and get a wireless charger and it should take care of your problems as well
Click to expand...
Click to collapse
Ok....wireless charger...but what about syncing with the PC?
Now I have JB 4.3 , for a custom ROM I need to use usb cable to connect to PC, rigth?.
For me it is annoying, because I do not know for sure if this is caused by updatind to 4.3 or is a harware problem.
My wife's phone had this issue last night and this morning; charger or computer, it wouldn't charge. I turned it off, took out the battery, SIM and uSD card and put them all back in. After that it started charging again. I don't know if this will solve the problem long term, but so far it seems to have done the trick...
NC_user said:
My wife's phone had this issue last night and this morning; charger or computer, it wouldn't charge. I turned it off, took out the battery, SIM and uSD card and put them all back in. After that it started charging again. I don't know if this will solve the problem long term, but so far it seems to have done the trick...
Click to expand...
Click to collapse
Lucky you...I did more than that, but no result in my case. I found on ''community.verizonwireless'' many more similar cases where ''customers support'' tried to avoid giving the answers for a real solution.
Well, our luck didn't hold. My wife's S4 wouldn't charge again last night. I tried another Samsung charger and a different cable but it wouldn't work either. When we left the house she tried it on the car charger and it worked great. Trying various other chargers we found that a kindle charger wouldn't work, but other third party chargers would. Even her PC USB port seems to work and she doesn't have the drivers loaded. For now she replaced the Samsung charger and cable that came with her phone for one that came as part of an accessory pack and it's happy again.
I have no idea what's going on with the thing. I asked one of the guys at the Samsung booth in Bestbuy and all he had to offer was reflashing the ROM or un-rooting it and doing a warranty exchange...
NC_user said:
For now she replaced the Samsung charger and cable that came with her phone for one that came as part of an accessory pack and it's happy again.
......and all he had to offer was reflashing the ROM or un-rooting it and doing a warranty exchange...
Click to expand...
Click to collapse
Can you check, please, if your new data cable has 4 or 5 pins(look to the side that connects to your phone )?
My first s4 done this. So I ended up with a replacement mdk phone after I figured out if you bend the lil piece in the charging port of your phone (not too much BTW) the charger will slide into the port as it's meant to.
Sorry I can't remember the tech term for that lil pin inside the charging port.
Sent from my SCH-I545 using Tapatalk
vwpiper said:
Help! My Samsung Galaxy S4 won't charge or connect to a computer. I've tried different chargers, cables, plug in locations, car, 110, computer. There is no dirt. Connection is clean. I have a spare battery and both of them will charge on the battery charger. I have tried backed up roms. I have done a factory reset.
All of this and nothing helped. Am willing to try anything. Verizon is going to send me a refurb.
Help please.
Click to expand...
Click to collapse
Just going to throw this out there....
I think the S4 is compatible with QI compliant wireless chargers. Amazon has some that are only $20... might be worth the purchase.... hell if I didn't have this tank of a case on I would buy it.
http://www.amazon.com/Lerway-Wireless-Power-Charger-Lumia920/dp/B00E9MUNWU
blueangel0508 said:
My first s4 done this. So I ended up with a replacement mdk phone after I figured out if you bend the lil piece in the charging port of your phone (not too much BTW) the charger will slide into the port as it's meant to.
Click to expand...
Click to collapse
Thanks for your answer, but I already did that....I even changed the flex cable with charging port, no luck for me.....
I think this issue it is not hw problem because, look what I did today:
-I put a new Rom , so I used MIUI FOR I9505 from http://forum.xda-developers.com/showthread.php?t=2306650
And now it behaves even stranger:
S4 is ON and wall charger is conected, (LED IT IS OFF but BATTERY IS BLINKING and is charging ) after battery level go up to 100% and disconect the charger, the LED STARTS TO LIGHT GREEN!!!!
So, now shows that is charging when charger is NOT connected?
alexmanu said:
Thanks for your answer, but I already did that....I even changed the flex cable with charging port, no luck for me.....
I think this issue it is not hw problem because, look what I did today:
-I put a new Rom , so I used MIUI FOR I9505 from http://forum.xda-developers.com/showthread.php?t=2306650
And now it behaves even stranger:
S4 is ON and wall charger is conected, (LED IT IS OFF but BATTERY IS BLINKING and is charging ) after battery level go up to 100% and disconect the charger, the LED STARTS TO LIGHT GREEN!!!!
So, now shows that is charging when charger is NOT connected?
Click to expand...
Click to collapse
Huh that's weird. How did you get miui to run on our phone? You've got the i545 right? I've been jonesing for miui ha.
As for the issue wish I could help you out...thought pushing that part would work
Sent from my SCH-I545 using Tapatalk

[Q] 5.1.1 update and charging differences

Hey guys,
Just got the 5.1.1 update to my g watch and i noticed some charging differences, namely i can no longer charge my watch with my pc (its an always on pc). I checked cables etc and all are fine, and it will still charge through an AC outlet. Ive tried usb 2.0 and 3.0 ports.
Just wondered if anyone else had noticed this behaviour? The charging indicator wont even show up when its plugged into my pc. Also noting that usb debugging still works through my pc and all is detected fine there
Norman
manor7777 said:
Hey guys,
Just got the 5.1.1 update to my g watch and i noticed some charging differences, namely i can no longer charge my watch with my pc (its an always on pc). I checked cables etc and all are fine, and it will still charge through an AC outlet. Ive tried usb 2.0 and 3.0 ports.
Just wondered if anyone else had noticed this behaviour? The charging indicator wont even show up when its plugged into my pc. Also noting that usb debugging still works through my pc and all is detected fine there
Norman
Click to expand...
Click to collapse
I have the same update, and have the same problem as you, I only noticed it last night when I put it on to charge, I charge mine every night on the same usb port and have had no problems till last night, like yours mine will only charge from mains now, I've tested all my usb ports and they are all working okay. I hope some one has an answer for it.
I´ve checked this and mine works perfectly with a 5m cable connected to a usb hub. I´ve checked with other cables and without hub, and this still works.
I was able to address the issue by rebooting the watch.
JohnnyK58 said:
I have the same update, and have the same problem as you, I only noticed it last night when I put it on to charge, I charge mine every night on the same usb port and have had no problems till last night, like yours mine will only charge from mains now, I've tested all my usb ports and they are all working okay. I hope some one has an answer for it.
Click to expand...
Click to collapse
So do i! Usb ports are working fine, my pc is custom built so i have specific ports designed for quicker charging of anything plugged into them
NYCArcana said:
I was able to address the issue by rebooting the watch.
Click to expand...
Click to collapse
If i reboot the watch whilst it is on the charger, it charges via usb in my pc - but if i take it off and put it back on, the problem returns, despite it still working with an AC charger, i'm assuming this is a software problem as android knows when its charging via usb or AC anyway. Hopefully a dev over here or the LG guys will fix it - i don't want to have to restart my watch every time i want to charge it, it's a pain in the arse and i shouldn't have to do it - i have a lack of AC ports in my room, hence i charge through my pc
manor7777 said:
If i reboot the watch whilst it is on the charger, it charges via usb in my pc - but if i take it off and put it back on, the problem returns, despite it still working with an AC charger,
Click to expand...
Click to collapse
Just checked - same behavior here.
Always fun to be a beta tester for Google. At least there's a workaround.
NYCArcana said:
Just checked - same behavior here.
Always fun to be a beta tester for Google. At least there's a workaround.
Click to expand...
Click to collapse
haha well, i can use an AC power source and charge my phone in my pc, they are both super close to me just my phone takes longer to charge
My watch was slower to charge I did notice that. Took an entire extra hour!
I have the same problem but I posted in the wrong thread (LG G Watch General)
http://forum.xda-developers.com/g-watch/general/watch-charging-update-to-5-1-1-t3115504
Hi
I have 2 chargers because I use one for travel. After updating to 5.1.1, one works and the other does not. I swapped the components and found it was the cable. I hope that this helps.
hallevison said:
Hi
I have 2 chargers because I use one for travel. After updating to 5.1.1, one works and the other does not. I swapped the components and found it was the cable. I hope that this helps.
Click to expand...
Click to collapse
All my cables seem to produce the same result, maybe it's just me - i tried the one that came with a quick charge charger and even that does the same thing. hmm, will pick up a new cable tomorrow and check it out!
I just had my watch on the charger and with out taking it off, restarted it and now it is charging. Definitely a bug of some sort
sent from a device using an app
manor7777 said:
All my cables seem to produce the same result, maybe it's just me - i tried the one that came with a quick charge charger and even that does the same thing. hmm, will pick up a new cable tomorrow and check it out!
Click to expand...
Click to collapse
I wouldn't bother. Some chargers just behave like USB devices to be able to charge older Blackberrys. I used the same cable with the PC and with a wall wart. Only the wall wart works unless I reboot the watch.
Thanks, most people seem to confirm its a bug.. That's what I love about xda, you can always find things like this. Thanks for all your help.
Hi, glad I found this thread.
I am having the same problem. It doesn't charge since the 5.1.1 update, but if it lays on the charger and I reboot it, it charges. If I take it off and put it back on, it doesn't charge and I need to reboot it again.
Have the same problem. After reboot, it charges on usb much slower but doesn't look like it (No charging icon). Otherwise I love the update.
Did you all factory reset after updating your watch? I also couldn't charge until I rebooted but it charges fine after the reboot.
Same issue
I can confirm the same behaviour. I have to reboot the g watch and then it start charging. Definitely a bug
Same here, watch was charging wen I went to sleep but charging stopped at around 60%
Verstuurd vanaf mijn Nexus 5 met Tapatalk
I've expressed my frustration over at the Android Wear help forum:
https://productforums.google.com/fo.../VRbw2FWOaiI;context-place=forum/android-wear
Oddly, my watch did NOT include the wall charger even though I got it new from Best Buy. Did anyone else not get a wall charger? I'm not the type to just blindly miss something as useful as a USB wall charger. I remember opening it up and saying to myself, "I guess I'll have to use my monitors USB port." I don't throw that stuff out. I still have the box and all the packing materials as well, and it's nowhere in there.

Categories

Resources