Hi all,
First, sorry for posting in quistions & answers. I cannot reply on the actual topic in development.
I flashed the Darksense 1.0.0 kernel which says the Fast Charge is supported. But after flashing i still can't fast charge. Ampere app shows it starts very nice on 1860mA but then slowly goes down to 250mA. I'm using a qc 3 fast charger. Someone has any idea what i'm doing wrong? Or is there another kernel i can try for qc support?
Deepdelver said:
Hi all,
First, sorry for posting in quistions & answers. I cannot reply on the actual topic in development.
I flashed the Darksense 1.0.0 kernel which says the Fast Charge is supported. But after flashing i still can't fast charge. Ampere app shows it starts very nice on 1860mA but then slowly goes down to 250mA. I'm using a qc 3 fast charger. Someone has any idea what i'm doing wrong? Or is there another kernel i can try for qc support?
Click to expand...
Click to collapse
The charging curve of all fast charge technologies decreases in gradient as the device charges, so a decrease over time of charging Amps is completely normal. In any case, in the next version of DarkSense kernel, we have increased the charging rate more.
Oke thnx! At least now i know i'm not doing anything wrong. I hope next version, will be there soon . Thnx for the great work.
Deepdelver said:
Oke thnx! At least now i know i'm not doing anything wrong. I hope next version, will be there soon . Thnx for the great work.
Click to expand...
Click to collapse
Just released it
Nice, installed it without any problems! Will let you know about the fast charge . Good work! Thnx!
If i charge it with my qc3 adapter it will charge for 1% a minute, not very fast, but definitly faster. If I use my qc3 power bank it charges a little slower. I don't know why cause the output seems the be the same.
But great work your kernel helped me a lot!
For me with elephone fastcharger It full charge in 2:20 hours More or less
Tried beta kernel 1.2.0 buy still charge is slow, and in my car's usb, It does not even charge, It just maintain the battery
Hey @Jonny Much faster after a wipe caché dalvik . Even in the car It charge really fast. Many thanksss
Is it possible to increase the sensitivity of the display with your kernel?
Deepdelver said:
Is it possible to increase the sensitivity of the display with your kernel?
Click to expand...
Click to collapse
Not currently, we do not have source code for touchscreen drivers
pe not qc
Deepdelver said:
Hi all,
Ampere app shows it starts very nice on 1860mA but then slowly goes down to 250mA. I'm using a qc 3 fast charger. Someone has any idea what i'm doing wrong? Or is there another kernel i can try for qc support?
Click to expand...
Click to collapse
The SOC doesn't support QC, you need an mtk pump express charger for quick charging. It should charge at [email protected]
Jonny said:
Not currently, we do not have source code for touchscreen drivers
Click to expand...
Click to collapse
Is there any change this source will come available? Cause I'm thinking about claiming warranty for it or wait to fix it by custom software.
Deepdelver said:
Is there any change this source will come available? Cause I'm thinking about claiming warranty for it or wait to fix it by custom software.
Click to expand...
Click to collapse
We are working on it.
Jonny said:
We are working on it.
Click to expand...
Click to collapse
Thnx for all your good work mate!
Is this Kernel compatible with Eragon 4.1?
stewakg said:
Is this Kernel compatible with Eragon 4.1?
Click to expand...
Click to collapse
Yes
Related
After installing XXUFMB3 I suddenly have problems which I never had before.
1. USB charging from PC is now on the fritz. i.e. It says it is charging but battery goes down at the rate of 1% per 4 minutes.
2. Charging with stock charger is next to impossible.
3. I can only charge with 2.1 amp chargers (those to tablets and ipads)
4. Battery life went down to 50%
I already changed the ROM and even bought new batteries and I still end up having these problems.
Please help me?
If you've already gone back to a stock ROM and tried other chargers then it sounds like a hardware fault inside the phone.
Original charger/lead known to be unreliable and faulty
can anyone point to me the latest stable stock ROM radio kernel and all?
You want me to Google that for you?
boomboomer said:
You want me to Google that for you?
Click to expand...
Click to collapse
I just want to know which is the latest ROM fox Galaxy S3 that works. I was told that the XXUFMB3 was OK. it didn't quite work out well for the two units I have.
Deadman said:
I just want to know which is the latest ROM fox Galaxy S3 that works. I was told that the XXUFMB3 was OK. it didn't quite work out well for the two units I have.
Click to expand...
Click to collapse
Just go to the stock rom thread and pick the next one down .
Or the same via sammobile.com
jje
JJEgan said:
Just go to the stock rom thread and pick the next one down .
Or the same via sammobil
jje
Click to expand...
Click to collapse
thank you very much.
I'm also going back to stock now.
suddenly after using xxufmb3 for few days, the phone stopped charging... even after plugged in the remaining power keeps on going down.
i'm on crdroid rom as of now.
Check this app: http://forum.xda-developers.com/showthread.php?p=36124435
It'll help you determine what's the charging current. Then through trial and error, you can determine where the problem lies.
Sent from my GT-I9300 using xda app-developers app
Re: OMG THIS IS SCARY
Oomahey said:
Check this app: http://forum.xda-developers.com/showthread.php?p=36124435
It'll help you determine what's the charging current. Then through trial and error, you can determine where the problem lies.
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Ok I'm on XXUFMB3 right now. Flashed it a couple of hours ago. Haven't tried charging yet. I'm on Omega ROM v44.2 4.2.1.
So Is it dangerous to continue using this ROM? Or does this issue get fixed after flahshing another rom?
Reply ASAP, XXUFMB3 might be slahghtering my phone's hardware right now!!
Hi guys,
I'm coming from the Oneplus One and that phone used to charge at a speed of 2ma.
Using some apps, I've come to see that the Oneplus X charges only at 1.2ma tops for me.
Is there any kernel which supports 2ma charging? Thanks!
I don't see the charging speed a problem, considering that it's got a lesser capacity battery. Charging times are fast enough that you wouldn't notice any difference. Just keep it down and let it charge.
As for kernels, you could check the developments section
Sent from my SM-G920F using Tapatalk
I guess blu spark kernel has fast charging support... Look it up
Mine charge at 1500mAH
Max voltage which can go through is 1800mAh for our phone
0-60%--- Phone charges at 1500mAh(Rapid Charge)
60-90%--Phone charges at 1200mAh
90-100%- 300mAh (Trickle Charge)
This is the case in all phones .. take it nexus 5 ... xiaomi mi4.....One plus one
rockuppl said:
Mine charge at 1500mAH
Max voltage which can go through is 1800mAh for our phone
0-60%--- Phone charges at 1500mAh(Rapid Charge)
60-90%--Phone charges at 1200mAh
90-100%- 300mAh (Trickle Charge)
This is the case in all phones .. take it nexus 5 ... xiaomi mi4.....One plus one
Click to expand...
Click to collapse
I understand trickle charging but does it really charge at 1800? Can you post some screenshots from an app?
Bluspark kernel only supports usb fast charge i.e charging is fast when connect to pc or something like that not charger.
mohammedtabish said:
Bluspark kernel only supports usb fast charge i.e charging is fast when connect to pc or something like that not charger.
Click to expand...
Click to collapse
yes, and you know what? ^_^ usb can't produce more than 0.5
btw, for OP - slower your phone charges better is for your battery life.
AlexVendettA said:
yes, and you know what? ^_^ usb can't produce more than 0.5
btw, for OP - slower your phone charges better is for your battery life.
Click to expand...
Click to collapse
Thanks I've heard this but never really noticed a tangible difference.
Right now I'm running CM 12.1 Master Awesome. Would you recommend I change to Blu Spark kernel?
RashidD said:
Thanks I've heard this but never really noticed a tangible difference.
Right now I'm running CM 12.1 Master Awesome. Would you recommend I change to Blu Spark kernel?
Click to expand...
Click to collapse
I understand why you would want to, but as i know bluspark doesnt "Support" cm for now but it works - try it, in case you always can go back on cm kernel, in using oos 2.2 with bluspark, gives me 4-5 screen time with Wi-Fi always on which is more than enough for me, waiting stable marshmallow ^.^
AlexVendettA said:
I understand why you would want to, but as i know bluspark doesnt "Support" cm for now but it works - try it, in case you always can go back on cm kernel, in using oos 2.2 with bluspark, gives me 4-5 screen time with Wi-Fi always on which is more than enough for me, waiting stable marshmallow ^.^
Click to expand...
Click to collapse
Alright cool. I was actually quite happy with the battery life. Yesterday was my first day and i got just over 4 hrs with a mix of wifi and lte. About 14 hrs standby. So not bad at all...
RashidD said:
Alright cool. I was actually quite happy with the battery life. Yesterday was my first day and i got just over 4 hrs with a mix of wifi and lte. About 14 hrs standby. So not bad at all...
Click to expand...
Click to collapse
Welp, then just keep things like they are for now, or tryout every combination, maybe you will find something that gives you more satisfaction oxygen is quite cool, very stock clear, the only problem I had so far was solved in last update(ril+4g connectivity sometimes stopped working and I had to go airplanemode)
Actually Blu Spark is supported on Cm 12.1. I highly recommend it. It's a drastic upgrade from the stock one used
RJDTWO said:
Actually Blu Spark is supported on Cm 12.1. I highly recommend it. It's a drastic upgrade from the stock one used
Click to expand...
Click to collapse
Upgrade in what way? Battery life?
RashidD said:
Upgrade in what way? Battery life?
Click to expand...
Click to collapse
Definitely. Don't forget about the ability to undervolt either. It helps a ton. Give it a try. Oh and xposed with Amplify and Greenify helps a lot too.
RJDTWO said:
Definitely. Don't forget about the ability to undervolt either. It helps a ton. Give it a try. Oh and xposed with Amplify and Greenify helps a lot too.
Click to expand...
Click to collapse
Did you notice a difference in Screen On Time? (SOT) or just standby?
RashidD said:
Did you notice a difference in Screen On Time? (SOT) or just standby?
Click to expand...
Click to collapse
Both. I get about 6-7 hours of SOT. As for standby, it doesn't budge but a percent over night. It's great for a 2500 mah device.
RJDTWO said:
Both. I get about 6-7 hours of SOT. As for standby, it doesn't budge but a percent over night. It's great for a 2500 mah device.
Click to expand...
Click to collapse
Which ROM are you on btw?
RJDTWO said:
Actually Blu Spark is supported on Cm 12.1. I highly recommend it. It's a drastic upgrade from the stock one used
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?p=63871059
Read this post, specially the part with "so far I support only oxygenOs"
But as I said it works.
AlexVendettA said:
http://forum.xda-developers.com/showthread.php?p=63871059
Read this post, specially the part with "so far I support only oxygenOs"
But as I said it works.
Click to expand...
Click to collapse
Thanks guys. I'm testing it out now and there seems to be noticeable improvement in battery life. Almost as good or decent as my OPO.
RashidD said:
Which ROM are you on btw?
Click to expand...
Click to collapse
Multiple ROMs haha. AICP, Cm 13, Sailfish, and Oxygen. I don't stick to one. AICP is the best in my opinion
Hello everyone,my redmi note 4 is charging very slowly it takes almost 5hrs to charge from 0 to 100.I have tried changing cables and adapter but nothing helps.
that'smee said:
Hello everyone,my redmi note 4 is charging very slowly it takes almost 5hrs to charge from 0 to 100.I have tried changing cables and adapter but nothing helps.
Click to expand...
Click to collapse
Even my device is getting same problem.
0 to 100 in 5 to 6 hrs.
soham_11 said:
Even my device is getting same problem.
0 to 100 in 5 to 6 hrs.
Click to expand...
Click to collapse
Letting your battery drain to 0% is bad and letting it charge to 100% is bad as well.
You both are ruining your batteries
Noter2017 said:
Letting your battery drain to 0% is bad and letting it charge to 100% is bad as well.
You both are ruining your batteries
Click to expand...
Click to collapse
You sound right,but
I have done that just for testing purpose.
Charging my device takes a long time .
Don't know why.
soham_11 said:
You sound right,but
I have done that just for testing purpose.
Charging my device takes a long time .
Don't know why.
Click to expand...
Click to collapse
I don't know which ROM you are using. It's a good start to search in your ROM's thread to see whether other people have the same problem and maybe found a solution.
If that doesn't help, flash a custom kernel like KudKernel (Oreo only) or Franco kernel (Oreo and Nougat). You will find them here in the development section
Noter2017 said:
I don't know which ROM you are using. It's a good start to search in your ROM's thread to see whether other people have the same problem and maybe found a solution.
If that doesn't help, flash a custom kernel like KudKernel (Oreo only) or Franco kernel (Oreo and Nougat). You will find them here in the development section
Click to expand...
Click to collapse
Currently I am using stock miui rom.
And yes, many people are facing this problem.
@Noter2017 can i flash franco kernel on stock miui 9.5 running nougut 7.0
that'smee said:
@Noter2017 can i flash franco kernel on stock miui 9.5 running nougut 7.0
Click to expand...
Click to collapse
No, Franco is for Custom ROMs like Lineage only.
Very common issue on the redmi note 4 mine went the same way, and would do the power supply disconnecting after it started to do this, get a new charge circuit very easy to change and cheap at under £3
https://rover.ebay.com/rover/0/0/0?mpre=https://www.ebay.co.uk/ulk/itm/273041868428
My Note 4 running stock MiUi 9.5.x (up to date) and I am too facing the same slow charging issue. Usually I charge between 20-80% and once a 10/12 days, I do a full 100% charge !!
Backup is good, satisfactory SoT but charging is hellishly slow !!
These are my charging stats {measured using ampere app}
Is it normal for redmi note 4.
Please measure yours and post the stats here .
Thanks.
So my charging port got damaged and it used to take hours to charge the phone while not using it, then I got it repaired recently
But I notice that while charging it, the battery keeps decreasing, I am using the original charger. I did also try a few other chargers but it seems to be the same
My battery does increase when screen is off and I leave it aside for a level, at a slower rate.
I want to know how to fix this battery decreasing while charging?
Try to install kernel again.
Agni kernel give you the option for thermal libs and more. This may change your charge time.
If not work for you, see in the forum a post with diode problem.
https://forum.xda-developers.com/redmi-note-3/help/rn3-pro-charging-charging-board-t3671977
Good luck!
i0N77 said:
So my charging port got damaged and it used to take hours to charge the phone while not using it, then I got it repaired recently
But I notice that while charging it, the battery keeps decreasing, I am using the original charger. I did also try a few other chargers but it seems to be the same
My battery does increase when screen is off and I leave it aside for a level, at a slower rate.
I want to know how to fix this battery decreasing while charging?
Click to expand...
Click to collapse
How much current u get from 0 to 70% ?
naik2902 said:
How much current u get from 0 to 70% ?
Click to expand...
Click to collapse
How do I check that?
i0N77 said:
How do I check that?
Click to expand...
Click to collapse
What rom u r using ?
i0N77 said:
How do I check that?
Click to expand...
Click to collapse
ampere app ig good for this
I'm using stock ROM and the current level on amepere shows around 140ma most of the time
naik2902 said:
What rom u r using ?
Click to expand...
Click to collapse
naik2902 said:
How much current u get from 0 to 70% ?
Click to expand...
Click to collapse
I'm using stock ROM and current(ampere) level is 140mA while charging
i0N77 said:
I'm using stock ROM and current(ampere) level is 140mA while charging
Click to expand...
Click to collapse
Install telegram chat app. all xda devs and active on telegram.
Just install it and search kenzo groups. Here very slow response.
Join chat. See u there ion77
use agni kernel with alternative thermal libs =)
if you dont like agni kernel i dont know other fix for it.
in my opinion you may try this and if it worked search alternative fix... but you know the problem.
if not try it you dont know if the thermal libs can solve your issue.
yopu try with other chargers... but with other cable???
Chrisis25 said:
use agni kernel with alternative thermal libs =)
if you dont like agni kernel i dont know other fix for it.
in my opinion you may try this and if it worked search alternative fix... but you know the problem.
if not try it you dont know if the thermal libs can solve your issue.
yopu try with other chargers... but with other cable???
Click to expand...
Click to collapse
I need to have twrp to flash it right? Can you link me "Agni kernel with alternative thermal libs" for Redmi note 3 and also, I can just directly flash it on my custom ROM?
I did try it with a lot of other cables too, same issue.
If you use Official this is the correct version https://forum.xda-developers.com/re...nel-24-09-2016-agni-puremiui-mm-v1-4-t3468042
You need a recovery
Here I'm sharing force fast charging magisk module for poco f1.
There are 2 modules here. Choose one of them that suits your phone best.
My suggestion: If you live in higher room temperature then you should go for 2600mAh otherwise choose 3300mAh
Installation:
Go to magisk manager.
Tap on Modules.
Select the module from your storage.
Reboot the device.
That's all
Thank you.
Please mention what's the use of these modules. Do they make phone charge faster?
lockhrt999 said:
Please mention what's the use of these modules. Do they make phone charge faster?
Click to expand...
Click to collapse
Hope you checked the post title
It enables force fast charge under mentioned battery temperature.
Does it not decrease as the phone gets higher battery percentage? Is the speed consta
nhossainbd said:
Here I'm sharing force fast charging magisk module for poco f1.
There are 2 modules here. Choose one of them that suits your phone best.
My suggestion: If you live in higher room temperature then you should go for 2600mAh otherwise choose 3300mAh
Installation:
Go to magisk manager.
Tap on Modules.
Select the module from your storage.
Reboot the device.
That's all
Thank you.
Click to expand...
Click to collapse
Does it not decrease as the phone gets higher battery percentage? Is the speed constant until it fully charged?
pabloescobar012 said:
Does it not decrease as the phone gets higher battery percentage? Is the speed constant until it fully charged?
Click to expand...
Click to collapse
It should decrease the speed after reaching 90%.
nhossainbd said:
It should decrease the speed after reaching 90%.
Click to expand...
Click to collapse
pls provide supported rom
markmywordz said:
pls provide supported rom
Click to expand...
Click to collapse
Supports all ROMs including MIUI & OOS.
these are Ben's Thermal, Just renamed!
huh...
MODERATOR will ban you OP.
heyalfaq said:
these are Ben's Thermal, Just renamed!
huh...
MODERATOR will ban you OP.
Click to expand...
Click to collapse
Get some life dude ?
you don't even know the difference between thermal & my module. My FC module and ben's thermal are totally different. Scripts are not encrypted, just open all files and compare yourself. And try to respect others work.
nhossainbd said:
Get some life dude ?
you don't even know the difference between thermal & my module. My FC module and ben's thermal are totally different. Scripts are not encrypted, just open all files and compare yourself. And try to respect others work.
Click to expand...
Click to collapse
r there 42°c n 46°c 3300mah force fast charge available?
flashed your zip. Phone not charging . am using pixel os
. how should i revert
the only thing that really worked for me
thanx alot
good job dude ?
does it simply uninstalled from magisk if anything goes wrong? and what about temperature does phone start heating, i am using optimus drunk kernel and charging is slow.
Great mods
Thanks for sharing these mods, but folks should realize that higher charging currents greatly reduce battery longevity as well.
timbuctoo said:
Thanks for sharing these mods, but folks should realize that higher charging currents greatly reduce battery longevity as well.
Click to expand...
Click to collapse
yeah but its within official limit isn't it
bravo2526 said:
flashed your zip. Phone not charging . am using pixel os
. how should i revert
Click to expand...
Click to collapse
That's really unexpected. You can just remove the module from magisk. And everything will revert back to previous stage.
Thank you.
mralam92 said:
does it simply uninstalled from magisk if anything goes wrong? and what about temperature does phone start heating, i am using optimus drunk kernel and charging is slow.
Click to expand...
Click to collapse
Simply uninstall from magisk.
sasukesama said:
the only thing that really worked for me
thanx alot
Click to expand...
Click to collapse
That's great! ?
Yo, this works wonders. I'd run back to stock rom every now and then just bc I missed how fast I could charge. Now I have it on every other rom bc of this mod. Thank you ?