I dropped my moto e 2015 in the water for about 20-30 seconds, accidently. Now after 24 hours everything seems to work fine. except for the touch experience. I can also see water inside the screen. and the right edge the touch is completely not working . Due to that , I cannot press the delete key on the keyboard. What should I do? should I use the phone. leaving it off and unused for few more days will help?
meVikki said:
I dropped my moto e 2015 in the water for about 20-30 seconds, accidently. Now after 24 hours everything seems to work fine. except for the touch experience. I can also see water inside the screen. and the right edge the touch is completely not working . Due to that , I cannot press the delete key on the keyboard. What should I do? should I use the phone. leaving it off and unused for few more days will help?
Click to expand...
Click to collapse
Yeah you should leave your phone switched off for 2-3 days.
Do not charge it and keep it outside, let the phone dry naturally from the heat of sun, and after that try booting again and tell
Related
I have a T-Mobile Pocket Phone Edition,
It's had a rough life but as kept going for over 3 years now.
For the last year I would have to realign the screen 2 or 3
times a week but over the last few months it keeps getting worse.
Sometimes the screen won't respond to anything anywhere,
then after I tap it a few times boom works fine.
Sometimes I'll tap on the “Ok” and the “Start menu” will activate.
Sometimes drawing a line up the center of the screen will end up
shooting all over the screen.
And sometime it will work perfectly!
I thought the problems were to erratic to be hardware so
I hard set after awhile it started again,
So I hard set and installed a different ROM after a coupe hours
the problem was back.
Also sometimes the align program will get stuck in a
loop that doesn't end.
I've searched but can't find an answer? Anyone have an idea?
I've already taken it a part once but couldn't see how to get
any further after I toke the back panel off? Please help!
WOW nobody? So no one was heard of this problem before?
Can anyone direct me to directions on taking apart the Wallaby?
Thanks <><
It's a problem with touch screen. You should check (and fix) it.
Maybe it is necessary to press well screen to the motherboard. (Sorry my english).
Ok, Can you tell me where that connection is?
Thanks
Toke everything apart, found the connection, cleaned everything (w/ screen wipe)
put it all back together. Still have the touch problem and now the backlight won't work!
I've found if I press the unit in my hand the touch panel works right,
I don't think it's a lose connection to the main board so I think it must be
one on the main board.
If anybody thinks they want it for parts let me know! :?
Recently my touchscreen has been acting up on me. Sometimes it will either lock up completely and ill just press power 2x to get it to work again. other times stuff will randomly start to open or if its on the home screen the phone will switch pages left and right at a very high rate of speed the screen almost looks like its flickering.
this just started yesterday, ive ran 2 antivirus apps on the phone and both say its clean so i doubt its a virus, im not sure if its hardware or software related, im thinking about doing a re-flash, but i have a feeling that might not fix the issue..
has anyone else encountered this problem? it can get annoying at times cause it almost stops me from using the phone completely.
Edit: I would also like to note, i thought it was the screen protector i had on, but i took it off and the screen is still acting up
I had this happen last night after I installed a screen protector I got from eBay (they were $4 for 10 with free shipping). I'm guessing it was something in the glue because as soon as I took it off, the phone went back to normal. It always seemed to be 'pressing' in the same spot because I was trying to send a text and it kept popping up with a menu about the contacts info. Also, when that would pop up, the capacitive buttons at the bottom (menu, home, back and search) wouldn't work so I had to lock the phone and unlock it to gain control.
scream_clarity said:
I had this happen last night after I installed a screen protector I got from eBay (they were $4 for 10 with free shipping). I'm guessing it was something in the glue because as soon as I took it off, the phone went back to normal. It always seemed to be 'pressing' in the same spot because I was trying to send a text and it kept popping up with a menu about the contacts info. Also, when that would pop up, the capacitive buttons at the bottom (menu, home, back and search) wouldn't work so I had to lock the phone and unlock it to gain control.
Click to expand...
Click to collapse
i had a Skinomi screen protector on, its been on for almost 2 months now and this only started last night so i dont think it was the screen protector
Jc61990 said:
i had a Skinomi screen protector on, its been on for almost 2 months now and this only started last night so i dont think it was the screen protector
Click to expand...
Click to collapse
Did any water get in the phone?
i have same problem and make me shock,
my motorola have anti glare screen guard
while iam eat chicken soup and play mini plan , i didnt notice if my finger are wet couz of soup, meanwhile i notice that at that time the touch screen are still good i can play the game, so i quickly try to clean it up using tissue , while i try clean up my phone keep pressing like crazy so i stop to clean it but it keep pressing like crazy, event i have already out from the game, i cannot stop it, so i must pull out the battery and put it back,
i think Atrix the touch screen are too unstable , compare with milestone milestone is better but it's less sensitive then atrix
it normal again after pull out the battery and i clean it up
I never got any water inside the phone, only on the screen protector when applying it to the screen as directed in the instructions for the skinomi screen protector.
the screen protector has been on the phone for 2 months no issues. its only now i see this happening.
i removed the screen protector to see the issue still there.
i have done a factory restore with no changes
i downgraded to 1.52 with the random tapping still going.
i think it might be hardware related.
im going to bring the phone to an AT&T store for a swap
Dear Sirs,
my Omate Truesmart's screen froze completely at the settings screen after I tried to reenable bluetooth. Now the screen is on and the buttons are not working (tried holding them for a minute) so I cannot power it off in any meaningful way. I have no tiny screwdrivers here (on vacations).
Does anyone know any way to shut down this device without dismantling it?
Or do I have to wait for the battery to discharge completely?
I have seen such absurd situation on no other device yet so far..
All best.
So how did it go? Battery empty and now up and running again?
I had the same with my device. I did had the tiny screwdriver at hand and removed the battery. Now the back lid won't fully close...
apetit said:
So how did it go? Battery empty and now up and running again?
I had the same with my device. I did had the tiny screwdriver at hand and removed the battery. Now the back lid won't fully close...
Click to expand...
Click to collapse
Exactly, the ghost left the watch after a few hours, and now it works again.
I thought to put it on the sun to overheat the CPU and trigger the reboot, but then - it might never wake up
So, the bottom line is - always carry watchmaker's tools in your pocket!
Cheers
Mirko321 said:
Exactly, the ghost left the watch after a few hours, and now it works again.
I thought to put it on the sun to overheat the CPU and trigger the reboot, but then - it might never wake up
So, the bottom line is - always carry watchmaker's tools in your pocket!
Cheers
Click to expand...
Click to collapse
Nah, leave the lid as long as you can. Like I said, mine won't fully close now. One drop of water in the wrong place and it's is bye bye TS.
My Z2 accidentally got submerged in water, and the water got in the phone. Basically I was in the kitchen while suddenly my phone slipped and fell into the bowl full of water, the charging port flap is very lose so it got open and voila. I've removed the water from the phone but there's still some moisture under the front and back cameras. The phones boots up just fine but the screen flickers a little bit and after 5-10 secs it goes completely black. I just want to know if I keep it off for sometime, and when all the water will evaporate, will it go back to normal or I will have to get it repaired? Thanks
Edit 1: I just found out that the touch screen works even after the display going off soon I tried increasing the brightness to full and the screen started working, although it still flickers a very little. On keeping the brightness on minimum the screen goes off again
hamzxoxo said:
My Z2 accidentally got submerged in water, and the water got in the phone. Basically I was in the kitchen while suddenly my phone slipped and fell into the bowl full of water, the charging port flap is very lose so it got open and voila. I've removed the water from the phone but there's still some moisture under the front and back cameras. The phones boots up just fine but the screen flickers a little bit and after 5-10 secs it goes completely black. I just want to know if I keep it off for sometime, and when all the water will evaporate, will it go back to normal or I will have to get it repaired? Thanks
Edit 1: I just found out that the touch screen works even after the display going off soon I tried increasing the brightness to full and the screen started working, although it still flickers a very little. On keeping the brightness on minimum the screen goes off again
Click to expand...
Click to collapse
Turn off your phone and open the charging and microSD bonnet and put it in rice for at least one day then check it
raminta said:
Turn off your phone and open the charging and microSD bonnet and put it in rice for at least one day then check it
Click to expand...
Click to collapse
I don't have any dry rice laying around so I've kept it in the open and it's way too hot here so I guess it'll all dry up
hamzxoxo said:
I don't have any dry rice laying around so I've kept it in the open and it's way too hot here so I guess it'll all dry up
Click to expand...
Click to collapse
Put it near a well ventilated place if no rice tub.
iXaidyiu said:
Put it near a well ventilated place if no rice tub.
Click to expand...
Click to collapse
The moisture under the cameras is now gone but the screen issue still persists
hamzxoxo said:
The moisture under the cameras is now gone but the screen issue still persists
Click to expand...
Click to collapse
Put it there overnight.
Hi all, I was a member here for a dozen of years, but cant recover my acc because Iam not using gmail anymore ; )
Back to question: I used z5c because lineage, after windows phones, and all worked fine. Yesterday, I placed phone in my front jeans pocket, had full hands of some bags. Then, I sat in car, took phone out and touch didnt worked. No any physical problem visible. Phone itself looks as before - mint condition. I tried to reboot several times, went into twrp... nothing happened. touch was unresponsive.
I left it turned off for, maybe 6 hours, then I turned phone on and touch worked! But, I noticed that it is very sensitive - really soft touch was enought to perform action. I took soft cloth to clean display and turned only display off. When I turned it on, after few seconds touch stopped working again!
Touch worked fine before, same during this short period of time when worked again. Never noticed any problem with it.
Any idea why this happened and what I can do?
UPDATE:
I left phone turned off and put it on charger. He had 20% bat. I took him at 99% turned on and touch working again!
also, I can bet, I am 100% sure, that yesterday, while using otg mouse, I didnt saw in settings > display > high touch sensitivity option even I tried to find it several times. I thought that option, for gloves is turned on. And now I went again there, and that option is present! Hows that... And it is turned off.
Anyone have idea what to do with touch? Why is that happening?