Using Windows 10 x64 with drivers freshly installed
GT-I9001, Firmware 2.3, Factory reset performed and drivers unistalled/reinstalled
Been searching for hours on this and can't get it to work. Captivate will connect to computer normally and allow file transfers. But when I try to put in download mode, the computer won't recognize it. I get a popup window that says USB device not recognized.
I'm trying to restore back to complete stock because I'm having random shut downs and other misc issues. I was trying to us Odin to do it but it doesn't recognize the phone. So I powered up the phone, started Odin, then plugged the phone in...Odin sees the phone now but of course needs it in Download mode to work...so I get ADB and while the phone is connected, powered up, and recognized by Odin, I put it in download mode using "adb reboot download". The command put the phone into download mode but then Odin lost contact the the bubble appeared again saying it wasn't recognized.
I've completely removed all the samsung drivers, shut down computer, reinstalled all the drivers, shut down the computer, plugged the phone into the computer and watch to see that all drivers were installed correctly and the computer recognizes the phone...
So it all works EXCEPT while in download mode...any ideas?
I've tried different USB cords but don't have another computer to try on...
I would say you should try Samsung kies, let them install drivers. Then use download mode.
PalmCentro said:
I would say you should try Samsung kies, let them install drivers. Then use download mode.
Click to expand...
Click to collapse
i did, but doesn't work.
up...
Chouiyekh said:
up...
Click to expand...
Click to collapse
maybe the drivers aren't working.
Try downloading the driver from here
BatDroid said:
maybe the drivers aren't working.
Try downloading the driver from here
Click to expand...
Click to collapse
the link detected as a virus
Chouiyekh said:
the link detected as a virus
Click to expand...
Click to collapse
what?
its Androidmtk.com
BatDroid said:
what?
its Androidmtk.com
Click to expand...
Click to collapse
The link blocked by malwarebytes
BatDroid said:
what?
its Androidmtk.com
Click to expand...
Click to collapse
i've tried the driver from android mtk but also unhelpful
Chouiyekh said:
Using Windows 10 x64 with drivers freshly installed
GT-I9001, Firmware 2.3, Factory reset performed and drivers unistalled/reinstalled
Been searching for hours on this and can't get it to work. Captivate will connect to computer normally and allow file transfers. But when I try to put in download mode, the computer won't recognize it. I get a popup window that says USB device not recognized.
I'm trying to restore back to complete stock because I'm having random shut downs and other misc issues. I was trying to us Odin to do it but it doesn't recognize the phone. So I powered up the phone, started Odin, then plugged the phone in...Odin sees the phone now but of course needs it in Download mode to work...so I get ADB and while the phone is connected, powered up, and recognized by Odin, I put it in download mode using "adb reboot download". The command put the phone into download mode but then Odin lost contact the the bubble appeared again saying it wasn't recognized.
I've completely removed all the samsung drivers, shut down computer, reinstalled all the drivers, shut down the computer, plugged the phone into the computer and watch to see that all drivers were installed correctly and the computer recognizes the phone...
So it all works EXCEPT while in download mode...any ideas?
I've tried different USB cords but don't have another computer to try on...
Click to expand...
Click to collapse
Had the same problem spent hours trying to fix it, gave up and used windows 7
rpsweb said:
Had the same problem spent hours trying to fix it, gave up and used windows 7
Click to expand...
Click to collapse
do you mean using win7 you didn't get the problem, mean you solve it ?
Chouiyekh said:
do you mean using win7 you didn't get the problem, mean you solve it ?
Click to expand...
Click to collapse
I couldnt get the adb driver to work when in download mode, it was exclamated in device manager. So I used windows 7 instead worked fine, no this isn't the answer you want to hear but wasted hours trying to get it to work on windows 10
rpsweb said:
I couldnt get the adb driver to work when in download mode, it was exclamated in device manager. So I used windows 7 instead worked fine, no this isn't the answer you want to hear but wasted hours trying to get it to work on windows 10
Click to expand...
Click to collapse
thank you man i'll try with win 7, keep in touch
Chouiyekh said:
thank you man i'll try with win 7, keep in touch
Click to expand...
Click to collapse
I just read right clicking on the adb device in device manager when your phone is in download mode and choosing automatically update driver can fix the problem
Related
after a couple failed odin flashes
my PHONE is STUCK in DOWNLOAD MODE and i can't use ODIN because my PC now says USB NOT RECOGNIZED
ive uninstalled/reinstalled driver
different ports..different usb cables..different pc and still no luck..and yes ive searched xda..and i have yet to find anyone with similar issues..any ideas?
i finally got my phone to work
IT SEEMS LIKE WINDOWS DOESNT BOTHER TO TRY TO INSTALL THE DRIVERS SO YOU HAVE TO DO IT MANUALLY THROUGH DEVICE MANAGER
1) download http://www.multiupload.com/NMPX3KMWRS
this has the 64 & 32 bit driver folders..put which ever one u use on ur desktop
2) open device manager..plug your phone..if your pc says usb not recognized and unknown device shows in device manager..right click..properties..then uninstall it..
3) unplug ur phone..plug it back in then unknow device should show up in device manager..go to its properties then click update driver..the select own drivers..then browse to the 64 or 32 bit folder and click ok then next..it will try to install but you might get a error..
hopefully it will say install gadget serial and fail..that means ur pc kinda recognizes it
then all u ahve to do is from there is go to device manager..go to the properties of gadget serial..update driver..and browse to the driver folder..and it should install..then u have to do it a couple of more times for when it recognizes other samsung devices such as the adb and composite
Instructions here
http://forum.xda-developers.com/showthread.php?t=803492
First, download http://www.multiupload.com/NMPX3KMWRS
This contains Odin, the Samsung Drivers, stock odin rom, updated odin rom, pit file.
If you don't want to lose your settings, etc. you can skip to the second part. If your phone still doesn't work than start from the top.
-PART 1-
Step 1.) Make sure you have the appropriate drivers installed for your phone. If you are on 64bit then choose 64, if you are on 32 choose 32. You may already have the drivers installed and it will tell you after you try to install them.
Step 2.) Power your phone off
Step 3.) Open Odin.exe and plug a usb cable to your computer that will connect to your phone (do not plug it in to the phone yet, just the computer)
Step 4.) Hold down both volume buttons at the same time and while holding them down plug the usb into your phone. You should see a COM message show up in Odin.
Step 5.) To ensure your phone is back to stock, in odin you will want to check the repartition button. ONLY CHECK IT WHEN YOU ARE FLASHING BACK TO STOCK. Leave the other check boxes the way they are.
Step 6.) Click the PIT button and select the 512.pit file
Step 7.) Click the PDA button and select Original.tar and then click Start
It should go through a bunch of steps and then your phone will reboot. Below are the steps to update it to the latest release.
Close Odin and power your phone off.
-PART 2-
Step 1.) Open Odin.exe and plug a usb cable to your computer that will connect to your phone (do not plug it in to the phone yet, just the computer)
Step 2.) Hold down both volume buttons at the same time and while holding them down plug the usb into your phone. You should see a COM message show up in Odin.
Step 3.) Leave all check boxes the way they are. Do NOT check the repartition box.
Step 4.) Click the PIT button and select the 512.pit file
Step 5.) Click the PDA button and select T959UVJI6.tar and then click Start
Hope this helps!!!
thanks for the idea..but i know how to do all that...
MY PROBLEM
my PC doesnt recognize my phone and its in download mode so i cant use odin
He gave u the link to the drivers your computer doesn't recognize your phone because the drivers uninstalled themselfs it happed to me also just do it see if it helps k
SmartBrother90 said:
thanks for the idea..but i know how to do all that...
MY PROBLEM
my PC doesnt recognize my phone and its in download mode so i cant use odin
Click to expand...
Click to collapse
Sent from my SGH-T959 using XDA App
Thegreat520 said:
He gave u the link to the drivers your computer doesn't recognize your phone because the drivers uninstalled themselfs it happed to me also just do it see if it helps k
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
if you look in my first post i said
"ive uninstalled/reinstalled drivers"
and if i said i tried it on other pcs that would me i would have to install drivers there too..so the driver idea has already been tried..thanks anyway
Hey, I know u said Odin wont recognize your phone, but does your computer recognize that the device or an unknown device has been attached when u plug your phone into the USB. What version of windows are you using.
Jonathan Rubcic
Electrical Engineer
Sent from my SGH-T959 using XDA App
Sorry, u said your computer recognizes that an unknown device is plugged in. Let me see what I can find. If you can get Into download mode, your phone can be fixed!
Jonathan Rubcic
Electrical Engineer
Sent from my SGH-T959 using XDA App
jarubcic said:
Sorry, u said your computer recognizes that an unknown device is plugged in. Let me see what I can find. If you can get Into download mode, your phone can be fixed!
Jonathan Rubcic
Electrical Engineer
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
my phone is in the download mode..matter of fact..its the only mode i can get into..but i cant do anything because my pc wont recognize it
I know this seems simple.... But unplug phone, shut down ODIN, re-open ODIN, plug phone back in.
SmartBrother90 said:
after a couple failed odin flashes
my PHONE is STUCK in DOWNLOAD MODE and i can't use ODIN because my PC now says USB NOT RECOGNIZED
ive uninstalled/reinstalled driver
different ports..different usb cables..different pc and still no luck..and yes ive searched xda..and i have yet to find anyone with similar issues..any ideas?
Click to expand...
Click to collapse
same problem here
All~G1 said:
I know this seems simple.... But unplug phone, shut down ODIN, re-open ODIN, plug phone back in.
Click to expand...
Click to collapse
tried that and still nothing
All~G1 said:
I know this seems simple.... But unplug phone, shut down ODIN, re-open ODIN, plug phone back in.
Click to expand...
Click to collapse
yea that doesnt work & it wouldn't. because the pc has to recognize the phone before odin can..an that the issue! thanks tho
I've also got this probem. Did you by any chance install the voodoo thing? Apparently it messes up your phone if you flash over it.
I think I might buy one with a broken screen for 200ish...............but I really hope I dont have to.
Anyone have a fix for this yet?
@xaymaca i finally got mines to work after 48 hours but it seems like it depends on luck
1) download http://www.multiupload.com/NMPX3KMWRS
this has the 64 & 32 bit driver folders..put which ever one u use on ur desktop
2) open device manager..plug your phone..if your pc says usb not recognized and unknown device shows in device manager..right click..properties..then uninstall it..
3) unplug ur phone..plug it back in then unknow device should show up in device manager..go to its properties then click update driver..the select own drivers..then browse to the 64 or 32 bit folder and click ok then next..it will try to install but you might get a error..
hopefully it will say install gadget serial and fail..that means ur pc kinda recognizes it
then all u ahve to do is from there is go to device manager..go to the properties of gadget serial..update driver..and browse to the driver folder..and it should install..then u have to do it a couple of more times for when it recognizes other samsung parts.
it seems like windows doesnt want to install the drivers itself
um, you just tried alot with those drivers and it eventually worked out differently?
RPGbig said:
um, you just tried alot with those drivers and it eventually worked out differently?
Click to expand...
Click to collapse
no basically first i uninstalled the "unknown device" through device manager
then i would plug the phone..go to device manager and update the drive manually..until gadget serial showed up..if not..i repeat the process..
then when gadget serial shows up..update its driver manually..then samsung adb should show up in device manager..it takes alot of time and patience
If your system still fails to recognize your phone. Try installing Mini Kies. Do a quick search there are plenty of download links for that software. Make sure you restart your system after uninstalling the device.
I had similar issues with myn. But eventually got over with by doing a clean install off the drivers.. Hope this helps.
so i did that and it recognized my phone. it says it on the computer and on odin it changed from 0:[COM4] to 1:[COM3]. but it still stays stuck on set PIT file DO NOT TURN OFF TARGET.
Jessejess87 said:
so i did that and it recognized my phone. it says it on the computer and on odin it changed from 0:[COM4] to 1:[COM3]. but it still stays stuck on set PIT file DO NOT TURN OFF TARGET.
Click to expand...
Click to collapse
what tar and pit files are you using, i had similar issues when i tried odin'ing back to ji6. however odin'ing to stock JFD worked beautifully. if you need help finding the proper odin files here is a mirror of them: Odin Mirrors
This happened to me before, and someone mentioned it earlier. Get into device manager on windows, go to the Universal Serial Bus (USB) section, and I uninstalled every option you see in there. Restart your computer and windows will automatically reinstall those items apon reboot. The phone should now be detectable...
EDIT: Fail, it appears you already got it solved...
hey im not sure what tar abd pit files are. im really new to this. question, with the mirror how would i use it? will it still work with my phone trippin lol and not being picked up on my computer.
Okay so this is making me so frustrated. I can not get my computer to recognize my razr. I have installed the usb drivers from moto, let windows fail at downloading driver and i have even tried motocast. running 64bit windows 7. i guess ill have to try linux if no one can help me.
arturocald said:
Okay so this is making me so frustrated. I can not get my computer to recognize my razr. I have installed the usb drivers from moto, let windows fail at downloading driver and i have even tried motocast. running 64bit windows 7. i guess ill have to try linux if no one can help me.
Click to expand...
Click to collapse
not even USB mode? PC mode? Windows Media Sync Mode?
vash_h said:
not even USB mode? PC mode? Windows Media Sync Mode?
Click to expand...
Click to collapse
i don't even get that option to choose what i want lol.
i plug it in, and right away i get a pop up. USB device not recognized. and that's it.
phone doesn't charge or do anything lol
hi,
what's the version of win 7 you are using?
i've just plugged my xt910 to win 7 professional 64bit and no more need of manually installed drivers.
greetings
arturocald said:
i don't even get that option to choose what i want lol.
i plug it in, and right away i get a pop up. USB device not recognized. and that's it.
phone doesn't charge or do anything lol
Click to expand...
Click to collapse
Try downloading SDK and installing the USB driver package? Or failing that, go under "device manager", delete everything related to your phone, and try again.
thanks guys but it turned out it was just my cable went bad... idk how but got a new ecomoto one and it worked.
win 7 ultimate btw
Help mee.
I have bought a s3 that is locked to Orange, need to unlock, but odin does not see the phone in recovery/dl mode.
Odin see the phone in normal mode , but each time i put into start/+vol/home odin see nothing.
I have kies updated.
Thanks
crazydiamond1970 said:
Help mee.
I have bought a s3 that is locked to Orange, need to unlock, but odin does not see the phone in recovery/dl mode.
Odin see the phone in normal mode , but each time i put into start/+vol/home odin see nothing.
I have kies updated.
Thanks
Click to expand...
Click to collapse
I had a similar thing when i was plugged into a usb hub
Was ok when i plugged directly into the pc
Install Samsung Kies to be able your PC to detect your phone via Odin
also check the debugging mode in the developer options
bordikun said:
Install Samsung Kies to be able your PC to detect your phone via Odin
also check the debugging mode in the developer options
Click to expand...
Click to collapse
I have Kies, also tried debugging, i need root to unlock phone
Try to use the latest Odin
Odin v3.04
bordikun said:
Try to use the latest Odin
Odin v3.04
Click to expand...
Click to collapse
I have uninstalled the older Kies, re installed the latest.
I have installed the lastest odin.
Have tried to link up with and without debugging, odin still does not see phone when in recovery mode.
Only time odin see the phone when phone is in normal mode.
Starting to get annoyed now lol, i cant cut my sim to fit phone, untill this is done
I cant see my s2 on odin either, what am i doing wrong ????
1. Reboot PC
2. Ensure KIES is not running and kill any KIES processes in PC task manager.
3. Download mode
4. Connect USB directly to PC port (no hub)
5. Wait for any drivers to instal or load on PC
6. Start Odin in administrator mode
If still no good;
a) Different USB cable
b) Different PC USB port and wait for drivers
Sent from my GT-I9300 using xda premium
Thanks . Seems that I had been pressing volume up not down.
I have another question . I used chainfire Rom to debrand the phone but keis does not recognize . How can I solve this . Could it be because the phone is rooted ?
i am having this problem at the mo, I have tried all of the above, apart from a different pc.
oden worked fine with my galaxy s2
is there any more updates on how to sort this out please?
thanks
ian
I know this is a 7 day old thread, but I feel for you having been in the same situation. Firstly, have you installed the Android SDK? If not then I advise you to do so. Do a search on how to install the SDK. There maybe smaller downloads available with a package of the binaries you need to do some testing i.e. adb. The instructions will elaborate about how to set up your Environment settings in Windows. Essentially ADB needs to be called from within any part of your Windows system....or else you will have to cd to its location each and every time you want to do something like this. So once you have done that, open command prompt and type adb and see what comes up? If it says bad command or file name it means your environment settings for the ASK are incorrect, if it displays the adb help text in command prompt you are ready to proceed.
When you plug your device in (not in DL or recovery modes) is it detected by the PC? If so then your drivers are probably fine. If not then it maybe 1 of 2 things? 1 the device is detected but the MTP drivers have not been loaded or 2. No detection what so ever and all drivers need to be installed.
To determine how to proceed you will need to do a bit of investigating.
Note the USB drivers are included as part of the Android SDK.
Check in Device manager inside of Windows to see if anything is detected when you plug it in. If so but it has a yellow exclamation ! then it would indicate you need to update your drivers (but not always?). From here you can test to see if the phone is detected and you only need MTP drivers.
If not then I would suggest uninstalling Keis all together and downloading and installing the Samsung USB drivers separately. Install the drivers. Plug in the phone. If it is not detected straight away, then reboot the PC then plug the phone into a different USB port. From here you can determine how to proceed by using adb.
plug your phone in via USB and open command prompt and type this: adb devices
You should see 1 of 2 things.
1) The words "list of devices attached" followed by a 16 digit long ID number a gap and the word "device"
2) just the words "list of devices attached" and then blank and nothing else?
If a device ID is returned then you can proceed with the following. Otherwise you need to do some additional trouble shooting
Proceed here:
Once it is detected by Windows and shows up in Explorer then unplug the phone and go into settings and developer options and check enable USB debugging. Once you have done this it should allow your device to be seen in DL and recovery modes.
Troubleshoot: If not detected try the following:
1) Reboot the PC and plug into a new USB port that you have not previously plugged into.
2) Try disabling USB debugging plugging the device in and then unplugging it and reenabling USB debugging
3) From the status bar try switching modes between MTP and PTP modes. Wait a good minute or so between to allow Windows to detect the driver change. Tip a good indication is your notification tray Icon with green USB disk with a magnifying glass swirling around....Note if you cannot see this at all you probably should drag it into the notification panel so that you CAN!
4) Open up device manager again and ensure no yellow exclamation marks !
Once all this is right and you can get List of devices attached followed by an ID number then you can for sure be able to detect your device from Odin. Make sure you are running Odin 3.04, run it as admin (not necessary but have heard that it helps?)
Good luck
James
I have an S4 Active that NO MATTER WHAT I DO, Odin will NOT see phone in Download mode, it will with the phone on, and my PC will see the phone, but not Odin. I am stumped. I have tried 3 PC's, I have ALL the drivers and then some. I am Stumped.
rekamyenom said:
I have an S4 Active that NO MATTER WHAT I DO, Odin will NOT see phone in Download mode, it will with the phone on, and my PC will see the phone, but not Odin. I am stumped. I have tried 3 PC's, I have ALL the drivers and then some. I am Stumped.
Click to expand...
Click to collapse
have you tried factory resetting the phone?
afasayan said:
have you tried factory resetting the phone?
Click to expand...
Click to collapse
Several times
rekamyenom said:
Several times
Click to expand...
Click to collapse
You can try with minimal/no drivers i.e. uninstall kies if you have it and delete the drivers you might have installed on your own-it sounds counter productive but it has worked for me a few times.
You can also try to either install kies or the drivers separately.
Try the forum for your own phone, the people there might know better about this problem.
Also what OS are you on?
afasayan said:
You can try with minimal/no drivers i.e. uninstall kies if you have it and delete the drivers you might have installed on your own-it sounds counter productive but it has worked for me a few times.
You can also try to either install kies or the drivers separately.
Try the forum for your own phone, the people there might know better about this problem.
Also what OS are you on?
Click to expand...
Click to collapse
I will give all that a try. I'm on 4.4.2 build NH3. That's why I need Odin, to get back to build NE3
rekamyenom said:
I will give all that a try. I'm on 4.4.2 build NH3. That's why I need Odin, to get back to build NE3
Click to expand...
Click to collapse
By OS I meant the computer's OS.
afasayan said:
By OS I meant the computer's OS.
Click to expand...
Click to collapse
I have tried several computers using Windows 7 and Windows XP both 32 and 64
hello people.
i was trying to flash the kernel from ics 4.0.4 . first i connected it to the computer to flash it from odin. the green thing that was supposed to show up in odin didnt show up. me being dumb, i clicked start on odin for the heck of it. on odin it said fail. on my player there was this weird symbol.
i tried taking out the bettery and then i waited a few seconds. then i turned it on and the same symbol was there. i also tried going into download mode but when i tried it just showed the weird symbol and then turned black and again and again. i also tried going in to recovery which also did the same kind of thing. (bootlooping) . so has anyone experienced this before.
device info:
samsung galaxy player 4.0 (usa version)
terrasilent kernel
rooted
running icyfusion.
any help would be apperciated!
Its basically the same thing as the Download Mode sign. Don't worry about the awkward symbol, just means you are in download mode
Sent from my YP-G70 using xda app-developers app
EcHoFiiVe said:
Its basically the same thing as the Download Mode sign. Don't worry about the awkward symbol, just means you are in download mode
Sent from my YP-G70 using xda app-developers app
Click to expand...
Click to collapse
Its not in download mode though, i TRY turn it off (which I cant cuz the same thing shows again and again.)
ABSOLUTELY no way to turn it on. -.-
the playa! said:
Its not in download mode though, i TRY turn it off (which I cant cuz the same thing shows again and again.)
ABSOLUTELY no way to turn it on. -.-
Click to expand...
Click to collapse
He said that it's the same as download mode. For your information this mode is a forced download mode which means that you need to flash something to get over it. In this case a new kernel.
zaclimon said:
He said that it's the same as download mode. For your information this mode is a forced download mode which means that you need to flash something to get over it. In this case a new kernel.
Click to expand...
Click to collapse
oh im sorry i didnt understand what he meant. but for some weird reason my computer makes the noise but it doesnt show anything as connected... not even unknown device or something. do you guyd have any idea how i could fix this?
the playa! said:
oh im sorry i didnt understand what he meant. but for some weird reason my computer makes the noise but it doesnt show anything as connected... not even unknown device or something. do you guyd have any idea how i could fix this?
Click to expand...
Click to collapse
Try these:
1. Be sure to have anything Kies related not running [as a process] in the background (Task Manager alt+ctrl+delete on your computer)
2. Restart your computer and try the same usb port again (Kies process closed again).
3. Try a different USB port.
4. Try a different usb cord (I have over 4 in my home due to phones).
5. Try a different computer (I have two in my home).
Flash your kernal again as this is usually the case the phone dash exclamation sign icon comes up, odin of course.
da1writer said:
Try these:
1. Be sure to have anything Kies related not running [as a process] in the background (Task Manager alt+ctrl+delete on your computer)
2. Restart your computer and try the same usb port again (Kies process closed again).
3. Try a different USB port.
4. Try a different usb cord (I have over 4 in my home due to phones).
5. Try a different computer (I have two in my home).
Flash your kernal again as this is usually the case the phone dash exclamation sign icon comes up, odin of course.
Click to expand...
Click to collapse
the "forced download mode" sign comes even when the player is not connected to the computer, but I will look at this.
the playa! said:
the "forced download mode" sign comes even when the player is not connected to the computer, but I will look at this.
Click to expand...
Click to collapse
nothing is working.
i think its bricked.
the playa! said:
nothing is working.
i think its bricked.
Click to expand...
Click to collapse
Have you tried flashing back to stock? There is a guide in how to do it, don't do it the odin way - it's too unstable and unpredictable. Flash back to stock with heimdell. Click on my name and you should find my recent past posts (6 to 10 most recent) explaining how to flash back to stock with heimdell.
da1writer said:
Have you tried flashing back to stock? There is a guide in how to do it, don't do it the odin way - it's too unstable and unpredictable. Flash back to stock with heimdell. Click on my name and you should find my recent past posts (6 to 10 most recent) explaining how to flash back to stock with heimdell.
Click to expand...
Click to collapse
i dont think heimdall recognizes it either.
but i will look into your instructions so im sure that i didnt miss anything out.
I ran into this once. What fixed it for me was doing
heimdall close-pc-screen
Click to expand...
Click to collapse
Thanks guys,
its been a while but my laptop DOEST NOT recognize my player when I plug it in my laptop. I uninstalled the drivers and when I try to install the drivers, I get error 10. KIES does not resolve the issue either. Any ideas how to make the laptop recognize the player?
By the way, I tried every USB port.
the playa! said:
Thanks guys,
its been a while but my laptop DOEST NOT recognize my player when I plug it in my laptop. I uninstalled the drivers and when I try to install the drivers, I get error 10. KIES does not resolve the issue either. Any ideas how to make the laptop recognize the player?
By the way, I tried every USB port.
Click to expand...
Click to collapse
uninstall, reboot, re-download drivers, reinstall
also, does you player recognize when it is plugged in? (ie it shows usb connected)
iurnait said:
uninstall, reboot, re-download drivers, reinstall
also, does you player recognize when it is plugged in? (ie it shows usb connected)
Click to expand...
Click to collapse
by reboot u mean the laptop right? And then reinstall the drivers? And the player charges but it says USB Device Not Recognized.
the playa! said:
by reboot u mean the laptop right? And then reinstall the drivers? And the player charges but it says USB Device Not Recognized.
Click to expand...
Click to collapse
put device in download mode
plug into computer
run zadig.exe
options --> list all devices
then in the menu of devices click samsung usb composite device
install driver
in heimdall you wont be able to tell if heimdall recognizes it or not.
this is hiemdall when you first start it up
this should be heimdall when youve added everything in.
now all you have to do is hit start
also both of these pics have comments that will help you. good idea to look at them. also feel free to comment
Sent from my YP-G1 using xda app-developers app
goldflame09 said:
put device in download mode
plug into computer
run zadig.exe
options --> list all devices
then in the menu of devices click samsung usb composite device
install driver
in heimdall you wont be able to tell if heimdall recognizes it or not.
this is hiemdall when you first start it up
this should be heimdall when youve added everything in.
now all you have to do is hit start
also both of these pics have comments that will help you. good idea to look at them. also feel free to comment
Sent from my YP-G1 using xda app-developers app
Click to expand...
Click to collapse
I did all of that but i can't seem to click start... Even th ready button is grey and says 0%
:/
Hey all
I have a Galaxy S3 i9300... Today I got the OTA for 4.1.1 Jellybean I updated and now I lost my root!!! (still have SuperSU app but doesnt work or gets uninstalled)
Now I am trying to root it again but Odin3 v1.85 wont recognize my Phone in download mode!! Recognizes it when phone is on but not when its off!! Downloaded latest Kies and had it closed from task manager and all its related apps off too but Still odin wont recognize it in download mode!! been tryin since i did the Darn UPDATE! PLZ HELP :S
sohaib770 said:
Hey all
I have a Galaxy S3 i9300... Today I got the OTA for 4.1.1 Jellybean I updated and now I lost my root!!!
>>>>>Of course you lost root .
(still have SuperSU app but doesnt work or gets uninstalled)
>>>> Root the phone again .
Now I am trying to root it again but Odin3 v1.85 wont recognize my Phone in download mode!! Recognizes it when phone is on but not when its off!!
>>> Phone is supposed to be on and in download mode not off to use Odin .
Possible failed OTA update as per multiple posts due to root not removed .
Leading to USB on phone not recognized try a factory reset first .
jje
Click to expand...
Click to collapse
JJEgan said:
sohaib770 said:
Hey all
I have a Galaxy S3 i9300... Today I got the OTA for 4.1.1 Jellybean I updated and now I lost my root!!!
>>>>>Of course you lost root .
(still have SuperSU app but doesnt work or gets uninstalled)
>>>> Root the phone again .
Now I am trying to root it again but Odin3 v1.85 wont recognize my Phone in download mode!! Recognizes it when phone is on but not when its off!!
>>> Phone is supposed to be on and in download mode not off to use Odin .
Possible failed OTA update as per multiple posts due to root not removed .
Leading to USB on phone not recognized try a factory reset first .
jje
Click to expand...
Click to collapse
Thanks for the reply
Sorry it was on and in download mode didnt get recognized :S and tried factory reset too!!! still no luck
Click to expand...
Click to collapse
sohaib770 said:
JJEgan said:
Thanks for the reply
Sorry it was on and in download mode didnt get recognized :S and tried factory reset too!!! still no luck
Click to expand...
Click to collapse
Try Odin 3.04
sent from here, there, somewhere!!
Click to expand...
Click to collapse
reinstall drivers, try a different usb port. if using a desktop, use the ports on the back of the PC
Sent from my GT-I9300 using xda premium
sohaib770 said:
JJEgan said:
Thanks for the reply
Sorry it was on and in download mode didnt get recognized :S and tried factory reset too!!! still no luck
Click to expand...
Click to collapse
Plz Respond someone....
Click to expand...
Click to collapse
THAnks!!!!!!!!!!! Shifting usb to back of computer worked!!! U SAVIOURS THANKS A LOTT!!!!
Galaxy S3 not being recognized in odin in download mode
Could someone please assist.
My rooted Galaxy S3 phone (FW v4.1.2) is stuck at the Samsung startup screen after installing a font app from the app store
To resolve I have tried:
1. The recovery screen - doing a factory reset and reboot
2.. Reflash through ODIN.
I can get get the phone into download mode but ODIN will not recognize the phone in Download mode (Funny that phone is recognised by Odin at the stuck Samsung boot screen)
- I have unistalled and reinstalled KIES and USB drivers
- I am using the stock USB cable
- Tried different USB ports on computer
- Tried on different computers
The problem may be Windows driver related. Because phone gets stuck at the Samsung startup screen, all processes of driver installation do not conclude successful. "MTP USB Device" shows error in Windows Device manager, USB composite deivce.
Uninstalled and reinstalled these a couple of times without success.
Please assist
Issues with usb on s3
Actually fixed my own Question....
My phone was in download mode and was not being recognized by my computer my windows 7 computer. I pressed the usb icon, where a box popped up saying that there was an unknown device. You could find this in device manager.
I then went to device manager to update the driver instead of pointing the device directly to the driver when i clicked browse my computer for software then it shows a location and option to let me pick from a list of device drivers on my computer then a box pops up showing model above that there is a little check box uncheck that two boxes will appear with manufacturer and model
Scroll samsung electronics and model samsung mobile composite device that is what you want to update the driver to...
I pulled the battery then re-entered download mode and windows to over installing the rest now it works fine. I would attach images but it will not let me for some reason. if anyone can help with that I will do it later.
THIS COULD POSSIBLY help with devices not being found on computers in bootloader or just on rom loaded and running..
Skywatcher1 said:
Could someone please assist.
My rooted Galaxy S3 phone (FW v4.1.2) is stuck at the Samsung startup screen after installing a font app from the app store
To resolve I have tried:
1. The recovery screen - doing a factory reset and reboot
2.. Reflash through ODIN.
I can get get the phone into download mode but ODIN will not recognize the phone in Download mode (Funny that phone is recognised by Odin at the stuck Samsung boot screen)
- I have unistalled and reinstalled KIES and USB drivers
- I am using the stock USB cable
- Tried different USB ports on computer
- Tried on different computers
The problem may be Windows driver related. Because phone gets stuck at the Samsung startup screen, all processes of driver installation do not conclude successful. "MTP USB Device" shows error in Windows Device manager, USB composite deivce.
Uninstalled and reinstalled these a couple of times without success.
Please assist
Click to expand...
Click to collapse
have you got the necessary drivers also you need to stop all kies activities.
uable to see added message inn download mode
tian105 said:
reinstall drivers, try a different usb port. if using a desktop, use the ports on the back of the PC
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
uable to see added message inn download mode!!!!!!!!!!
Please help
Maybe solved it
Hey guys, i know it's a bit late now, but i had exactly the same problem with my gt-i9300 (got stuck on samsung splash screen and odin didn't recognize it in download mode) and just realised that everytime, i connected my phone to my PC in download mode, a message would appear that "Gadget Device" (or something like that) was connected. Then i searched in my device manager for the name of it (i found it under USB-Devices) and uninstalled the driver of it. As i connected it again with odin started it would install the driver automatically and *swoosh* odin recognized it.
A year and some later after the last post and I seem to be having this problem as well... I believe it was due to a bad flash at very low battery level which ended up in encryption failure ya da da, factory reset, clear/format everything and flash custom rom from SD because any other connection would not work.... then managed to get windows (many flavors inc. 7, 8 and 10) to connect as MTP or in USB debugging mode but Odin mode (download) just won't do anything... i put the phone in DL mode, nothing happens, no windows connection sounds, no changes in devices manager, even when searching for new hardware. I'd be very interested to know if anyone has had anything like that. I'd really like to flash stock to go back to a custom rom, flash twrp to replace cwm but all seems to no avail if i can't get a connection while in DL mode.
tried to install adb fastboot but also nada since no connection is being made.... might be something with DL mode gone awry with the bad flash... long story but OTA update from current ROM decided on its own to push update even though battery was at 5% and no user interaction ever happened...
we'll see what happens...
after replacing mainboard of my s3 gt-i9300 my computer doesn't recognize phone at all in download mode but in while phone is on
mtp works fine via usb
please help
Are you using the original Samsung USB cable when the phone is in download mode?
romeeoo said:
after replacing mainboard of my s3 gt-i9300 my computer doesn't recognize phone at all in download mode but in while phone is on
mtp works fine via usb
please help
Click to expand...
Click to collapse
Driver issue. Find the correct drivers.
Beamed in by telepathy.