Related
Hey guys
I was wondering , since it takes this phone over 3 hours to fully charge... If I buy a Nokia charger with an output of 1.2 mah ,would it take a shorter time for this phone to charge? Its own charger has 0.7 mah output..
No. SGS2 has a capped charge rate of 650 as far as I know.
----------------------
GTI9100 KK5
yes but it might get hot. i used to charge with playbook's charger all was well. but now i use the samsung S2 charger. but i never checked if it was charging faster
Ok, thank you both
atifsh said:
yes but it might get hot. i used to charge with playbook's charger all was well. but now i use the samsung S2 charger. but i never checked if it was charging faster
Click to expand...
Click to collapse
Charging is controlled by the phone only and varies depending on whether it detects a USB data link or not. And the battery temperature.
So, provided the charger is rated at 700mA or greater, the phone will charge at the fastest rate it sets. On USB, the charge rate is lower. USB 2 ports have a maximum of 500mA output... and if the phone is on, the charge rate is often lowered further.
I use an iPAD2 charger for convenience, which is rated at 2A. The phone charges fine, but only at the same rate as the stock Samsung charger.
LenAsh said:
Charging is controlled by the phone only and varies depending on whether it detects a USB data link or not. And the battery temperature.
So, provided the charger is rated at 700mA or greater, the phone will charge at the fastest rate it sets. On USB, the charge rate is lower. USB 2 ports have a maximum of 500mA output... and if the phone is on, the charge rate is often lowered further.
I use an iPAD2 charger for convenience, which is rated at 2A. The phone charges fine, but only at the same rate as the stock Samsung charger.
Click to expand...
Click to collapse
thanks for the info dont know about S2 but i know few brands allow that. blackberry is one of them, using playbook charger on their phones charge them faster but battery gets hot.
I cant find the exact post to link it for you but I'm sure the devs had a discussion about it in the siyah dev thread.
Mains capped at 600 by the device.
http://forum.xda-developers.com/showthread.php?t=1263838&page=1406
----------------------
GTI9100 KK5
Well, I needed more actual facts than technical stuff. So the idea is not to buy the nokia charger cause the sgs2 wont charge faater. This sucks. HTC evo 3d battery charges to full in abou 1,5 hours and it lasts enough so...I really dont understand samsung
In my ROM there is an option to enable fast charging. If you enable that, a charger with a higher mAh will make sense.
Probably the heat issue is the main reason for not implementing a higher charge rate. Battery degradation world be another.
Sent from my GT-I9100 using xda premium
I don't think you should use a bigger charger with a higher voltage to charge your phone, the battery for your SGS2 might not be able to handle the amount of voltage from the charger
MacBreQ said:
In my ROM there is an option to enable fast charging. If you enable that, a charger with a higher mAh will make sense.
Click to expand...
Click to collapse
Thanks but I prefer stock roms
Hello all, I just bought a Xperia Ray, and it's kinda weird that when it's 40 percent, and I connect to my laptop it takes about 2 hours to get to 90 percent, but when I use the wall charger, it takes 5 hours only to get to 80 percent!!! And I've tried it a lot so far, it's the same story...anyone knows the reason?!
swamks said:
Hello all, I just bought a Xperia Ray, and it's kinda weird that when it's 40 percent, and I connect to my laptop it takes about 2 hours to get to 90 percent, but when I use the wall charger, it takes 5 hours only to get to 80 percent!!! And I've tried it a lot so far, it's the same story...anyone knows the reason?!
Click to expand...
Click to collapse
The wall charge is not supplying enough current. Many are very poor performers. I charge mine with my wife's Blackberry tablet charger and that provides a steady 2 amps @ 5 volts. Most cheap wall chargers provide less than 400ma @ 4.5 volts.
interesting...so charging with the laptop will not hurt the battery in the long run?!
swamks said:
interesting...so charging with the laptop will not hurt the battery in the long run?!
Click to expand...
Click to collapse
Not at all. The charging circuit on the Ray will handle whatever is fed into it (up to a point). The laptop USB provides a higher and more stable voltage at the required amperage than the wall charger does so the Ray charges quicker. Finding a decent USB wall charger is actually not that easy. Most are garbage.
Hi people
Since I'm part of the lucky people owning a Huawei Ascend Mate 7 (MT7-TL10), I'm actually looking some accessories like a quick charger.
I wish a charger better than the original one if possible, with EU pins, and with a good quality checked (I prefer to avoid some product with awesome specs but not tested ...)
So anyone have any idea where I can find a good charger, and without any risk for my phone ?
Thanks
WolwX said:
Hi people
Since I'm part of the lucky people owning a Huawei Ascend Mate 7 (MT7-TL10), I'm actually looking some accessories like a quick charger.
I wish a charger better than the original one if possible, with EU pins, and with a good quality checked (I prefer to avoid some product with awesome specs but not tested ...)
So anyone have any idea where I can find a good charger, and without any risk for my phone ?
Thanks
Click to expand...
Click to collapse
for few days i went to jarir book store on KSA . I found Charger good price also 2 USB 5 volt 2.4 Amber ... compatiable with mate 7 and faster from orignal ...
just to know more fasting to charge wil damge your batter of mate 7 quickly .also orignal 2 A will damge
for me I charging with Iphone charge 1A good for batter and Stander and low risk to Device
If you want proper charging, then always use the accessories coming with that product. It is tested for sure and good. Other than that, you can use any charger delivering the same charge. The original charger is 5 volt, 2 Ampere. Don't use anything above 2 amperes as it may damage the device. Below that will charge it slowly.
BTW, why you don't want to use the original charger?
Sent from my Coolpad 9976A using Tapatalk
I use Nexus 6 Turbo charge (made by Motorola) 5v 1.6A it charge full battery in 90 minute.
http://www.motorola.com/us/accessories/power-storage/chargers/motorola-turbo-charger/motorola-turbo-charger-pdp.html
Is it safe for battery life of Mate 7?
I'm using a NTT Docomo Quickcharge 2.0 adapter and It does support it even though is not specified and it's not a qualcomm chip.
Sent from my HUAWEI MT7-L09 using Tapatalk
djmaxi said:
I'm using a NTT Docomo Quickcharge 2.0 adapter and It does support it even though is not specified and it's not a qualcomm chip.
Sent from my HUAWEI MT7-L09 using Tapatalk
Click to expand...
Click to collapse
Can you test it with ampere (free in gplay) i don't think it will charge over 1800mA so that it acts like a normal 2a charger
Fast charging
Using a fast charger will destroy your battery faster. Not recommended as the battery is not removable. You can get a battery and if you are comfortable removing the back and swapping it out then go for it.
Hi,
PoopDonkey said:
Using a fast charger will destroy your battery faster. Not recommended as the battery is not removable. You can get a battery and if you are comfortable removing the back and swapping it out then go for it.
Click to expand...
Click to collapse
that is not correct as you are not connecting the charger to the battery directly. In fact the charger is just a power supply. The actual charger is integrated into the phone (charging controller).
In general you need to know that volts are pushed to the device by the power supply and amps are drawn by the device (phone) from the power supply. Therefor using a power supply with more than 5V will kill your phone but using one with 2A, 3A or even 4A will make no difference as the charging controller will just pull the amps required. Because of that you can not really fast charge a phone by changing the power supply only if the phone supports the fast charge option (for example some Nexus phones).
I tested this myself with a power supply (can provide 5V and 1.5 to 4 amps) and an amp meter. The phone always drew between 1.5 and 1.6 amps (with and empty battery, 8 to 10% left) regardless of the selected amps of the power supply. Using a power supply with less than 1.5A will kill the power supply as the phone tries to draw the 1.5 amps or more. As result the power supply will get hot and eventually die.
Since battery is not removable be careful with fast charging, since it will decrease the life span of the battery and in the end it will just give you less battery performance.. it is stupid... however.. there is situations where it can be really needed though but not on a regular basis..
Last weekend I would really had needed fast charging.. It forced me to spend about 3 hours on a cafee so I could make it 100% so I did know I did survive the day with gps and all other things.. However in these situations I really like the ultra power saving mode..it saved me that night.. when I was lost in stockholm.. and my phone was really the only way to get contact with people
blackinfinity said:
Since battery is not removable be careful with fast charging, since it will decrease the life span of the battery and in the end it will just give you less battery performance.. it is stupid... however.. there is situations where it can be really needed though but not on a regular basis..
Last weekend I would really had needed fast charging.. It forced me to spend about 3 hours on a cafee so I could make it 100% so I did know I did survive the day with gps and all other things.. However in these situations I really like the ultra power saving mode..it saved me that night.. when I was lost in stockholm.. and my phone was really the only way to get contact with people
Click to expand...
Click to collapse
Why don't you buy a powerbank? I can advice you the xiaomi 16000mah. That one charges fast and you can be mobile.
Any recommendations?
I wonder if a S6 charger do the trick. Stock charger is too slow damn. Spending 3 hours to have a full charge is not acceptable for me.
I'm going to be honest, it doesn't really matter how you charge your phone as long as you don't go over 5v and 2 Amps. Batteries will automatically lose cells from charge cycles and by the time you feel the effects of the battery going bad, you would have already moved on to the next device for the next person to worry about. And saying to use the Stock Charger isn't really good enough as the Stock charger doesn't serve as a Car charger also. If you want to charge your phone quick, and you already have a 2 Amp charger, Check your microUSB cable. Don't use junk cables, buy quality or use the cable you received with the device. You get what you pay for. Fast Charging won't work as the Charger has a chip inside that communicates with the Phone and Device. Also, when buying a charger, don't just randomly buy a charger online, Make sure its UL Tested. Even if it says UL tested, there should be a test number on that UL Label, take it a step further and google it and make sure it matches the charger specs and passes as knockoff chargers are notorious for copying other chargers Regulatory icons to make it seem authentic. You don't want to buy a junk charger that ends up burning your house down or gives you a very bad 120 Volt shock through the microUSB cable that would also kill and fry your phone.
treem said:
I use Nexus 6 Turbo charge (made by Motorola) 5v 1.6A it charge full battery in 90 minute.
http://www.motorola.com/us/accessories/power-storage/chargers/motorola-turbo-charger/motorola-turbo-charger-pdp.html
Click to expand...
Click to collapse
1.6A is nothing.. i use 2.0A and it still chrges 3 hours
one friend conected his phone to a hi suite, he went to repair sistem or something like that, and it pop out an option of QUICK CHARGE... even he doesent know how that hapends, now his phone charges faster. he is on b331 rom
cyvr1 said:
Hi,
that is not correct as you are not connecting the charger to the battery directly. In fact the charger is just a power supply. The actual charger is integrated into the phone (charging controller).
In general you need to know that volts are pushed to the device by the power supply and amps are drawn by the device (phone) from the power supply. Therefor using a power supply with more than 5V will kill your phone but using one with 2A, 3A or even 4A will make no difference as the charging controller will just pull the amps required. Because of that you can not really fast charge a phone by changing the power supply only if the phone supports the fast charge option (for example some Nexus phones).
I tested this myself with a power supply (can provide 5V and 1.5 to 4 amps) and an amp meter. The phone always drew between 1.5 and 1.6 amps (with and empty battery, 8 to 10% left) regardless of the selected amps of the power supply. Using a power supply with less than 1.5A will kill the power supply as the phone tries to draw the 1.5 amps or more. As result the power supply will get hot and eventually die.
Click to expand...
Click to collapse
so much misinformation
this post is the only one who gets it right.
Kalemucu said:
Any recommendations?
I wonder if a S6 charger do the trick. Stock charger is too slow damn. Spending 3 hours to have a full charge is not acceptable for me.
Click to expand...
Click to collapse
You have not read my earlier post or you did not understand it. Changing the charger on the Mate 7 will have NO effect (zero, nada) on the time required to charge your phone except the charger delivers less then appr. 1.6A. Then it would take longer and evetually kill the charger. The Mate 7 uses a Kirin chip which has no fastcharge implemented. Samsung uses Qualcomm Chips with implemented fastcharge technology. The charger (in fact a power supply) and the phone/CPU/charge controller need to communicate with each other, otherwise fastcharge will not be activated (the reason fastcharge with charge-only cables does not work because they lack the required data cables for communication).
I'm going to be honest, it doesn't really matter how you charge your phone as long as you don't go over 5v and 2 Amps.
Click to expand...
Click to collapse
Wrong. Correct would be "I'm going to be honest, it doesn't really matter how you charge your phone as long as you don't go over 5v." The amps of the charger don't matter at all -> amps are PULLED by the phone not pushed to the phone. You could use a charger with 100 or 1000 amps and it would not hurt your phone a bit as long as it is only charged with 5 Volts.
More amps (>1.6A) on the charger do not improve the time for charging one second.
1.6A is nothing. i use 2.0A and it still chrges 3 hours.
Click to expand...
Click to collapse
Yes, and that won't change one bit even if you use the best and most expensive charger and a 1000$ cable. The Mate 7 is limited by its hardware (built in charge controller) and pulls max 1.6A. End of story.
As long as you don't understand how charging works you will spend 100's of bucks for cables and chargers to no avail.
The only reason, why charging with some charges is quicker than with others is that those chargers actually deliver the amps they are supposed to deliver. There are a lot of cheap/bad chargers out there which are labelled with 5V/2A but only deliver a fraction of the amps. You can identify those chargers easily because they get extremly hot. I use a 2A charger from Aukey which gets only lukeworm.
I know there is a thread about what charger to buy, but I have a specs question. Mine z5 came with the International charger and I am in the US. I noted it is 5v and 1.5a. I have a 5v 1a charger on hand. Can I use that?
Sure, it will just take longer to charge.
No lasting negative effects on the battery?
BigHulkDiesel said:
No lasting negative effects on the battery?
Click to expand...
Click to collapse
Most certainly no negative effects. In theory it should actually be better for the battery to charge it with less current, but I don't know if that is true.
Different topic: I read that there are multiple versions of the Z5 (US, Europe, ...) and that they support different LTE frequencies. So maybe you want to check if your mobile connection works as intended, if you don't have the US version.
My phone is showing LTE after choosing my apn settings.
I tried using a 5V 1A charger with my phone and it doesnt seem to work. (It works fine on my old phone) The charge light keeps turning on and off. The vibration pulse you hear when it starts charging keeps pulsing too.
Better use an HIGHER amperage, than lower!! Charger will adapte it to phone specifics...A lower amperage will reduce your battery capacity in long time.
I once connected my Z5C to an old 500mA charger (caught the wrong cable) and kept using it a bit (screen on, etc.) and it gave me a nag screen that said that the charger is not suitable because apparently the battery drain from usage was more than what trickled back in.
However, if left alone even a 500mA charger should eventually charge the phone, taking much longer though.
Generally, with chargers, you need to get the voltage right. If the Amperage is higher that what the OEM charger is it does not matter. The electronics in the device limit the charge to what the device can handle. The Amperage on the charger is the max it can deliver. In other words, the charger does not pump 2.5A into the phone forcefully, the phone just nibbles whatever it can take (say 1,5A).
farfetch said:
Better use an HIGHER amperage, than lower!! Charger will adapte it to phone specifics...A lower amperage will reduce your battery capacity in long time.
Click to expand...
Click to collapse
Any reliable source for that? The charging will be slower - yes, but I seriously doubt, that this has negative long-term effects on the capacity.
dd23 said:
Any reliable source for that? The charging will be slower - yes, but I seriously doubt, that this has negative long-term effects on the capacity.
Click to expand...
Click to collapse
Just try it by yourself for few days
Sent from my E5823 using Tapatalk
I think you need a 2A charger to be sure with the Z5c. Most of my older chargers take hours to charge it, and the car USB port (Nissan Qashqai 2015) barely charges it at all.
The UCH20 that came with the phone, takes 2 hours 15 mins to charge the phone fully. I got a quick charger which takes around 1 hour and 10 mins at max
Wow, really?
It is basic electronics. The voltage must be the exact one. Amperage is what the device draws , therefore the charger must be capable to provide a minimum not a maximum.
I repeat, it is basic electronics!
Now a more pertinent question :
What are the voltages for quick charge ? Does anyone know?
If someone has a original charger with quick charge can you please state what voltages are written on it?
Should be 2 or 3 voltages with lowest 5V
Edit : Found myself the info on Sony UK website of a Sony charger.
[email protected],
[email protected],
[email protected]
farfetch said:
Better use an HIGHER amperage, than lower!! Charger will adapte it to phone specifics...A lower amperage will reduce your battery capacity in long time.
Click to expand...
Click to collapse
I also want a source for that... It's the first time in my life i hear it's the opposite... and i have been charging this phone with 1 amp or 500mA (with pc usb) for the past 4 years, battery is still fine. Only used a 1.5A charger a few times.
On the other hand, my sisters z5 had a swollen battery a year ago, she always used quick chargers...
farfetch said:
Just try it by yourself for few days
Click to expand...
Click to collapse
What do you mean by that?
you are not going to notice battery degradation in just a few days of charging...
EDIT: i only notice now that i accidentally replied to a post from years ago, sorry for that...
Has any tried charging honor 5x with 2amp charger??
How much time does it took to charge fully..??
With stock 1amp it took 3hrs to charge fully....as i know snapdragon 615 nd 616 support quick charge 2.0...can it be utilized with 2amp charger??
Sent from my KIW-L22 using Tapatalk
Good question. . I have a Qualcomm 2.0 fast charger at home, I'll plug mine into it and check the input
paoloroeseke said:
Good question. . I have a Qualcomm 2.0 fast charger at home, I'll plug mine into it and check the input
Click to expand...
Click to collapse
See how much it takes from 5% to 100%..[emoji41] by the way which honor 5x u have KIW-L22 or KIW-L24 ??
Sent from my KIW-L22 using Tapatalk
I dont understand what quick charge does exactly. If i have a charger that puts out 3 amps at 5 volts and the battery is 3000 mAh then it should take about an hour to charge if its completely drained. That the basic rule for 1C charging rate for lithiums right? so does the qualcomm charger deliver higher that 1C rates?
It doesn't actually work that way which would be bad for the battery, they charge faster when the battery is low and slow down as its fuller or reach a certain temperature.
As for Qualcomm quick charge, it works a bit different than the USB standard. I'm still not clear on the whole thing, but this is what I gathered:
Quick Charge 3.0
3.2v - 20v dynamic, 200mV increments
Up to 3A
Snapdragon 820, 620, 618, 617, and 430
Quick Charge 2.0
5V / 9V/ 12V
Up to 3A
Snapdragon 200, 400, 410, 615, 800, 801, 805, 808 and 810
-
5V/2A, 9V/2A, 12V/1.67A
Quick Charge 2.0 Class A can provide up to 24 watts over a micro USB connector, 36 watts with a Type-C connector, and Class B can reach 60 watts or more.
Quick Charge 1.0
5V, 2A
Snapdragon 600
This is the rating for one 19.5W QuickCharge 3.0 wall charger:
Output (Type-C Quick Charge 3.0 Port): 3.6-6.5V/3A, 6.5-9V/2A, and 9-12V/1.5A
eksasol said:
It doesn't actually work that way which would be bad for the battery, they charge faster when the battery is low and slow down as its fuller or reach a certain temperature.
As for Qualcomm quick charge, it works a bit different than the USB standard. I'm still not clear on the whole thing, but this is what I gathered:
Quick Charge 3.0
3.2v - 20v dynamic, 200mV increments
Up to 3A
Snapdragon 820, 620, 618, 617, and 430
Quick Charge 2.0
5V / 9V/ 12V
Up to 3A
Snapdragon 200, 400, 410, 615, 800, 801, 805, 808 and 810
-
5V/2A, 9V/2A, 12V/1.67A
Quick Charge 2.0 Class A can provide up to 24 watts over a micro USB connector, 36 watts with a Type-C connector, and Class B can reach 60 watts or more.
Quick Charge 1.0
5V, 2A
Snapdragon 600
This is the rating for one 19.5W QuickCharge 3.0 wall charger:
Output (Type-C Quick Charge 3.0 Port): 3.6-6.5V/3A, 6.5-9V/2A, and 9-12V/1.5A
Click to expand...
Click to collapse
Thanks for the info eksasol.. I guess I was just being simplistic. I always think of battery charging in terms of hobby remote control chargers for lipo's. True, the charger (or phone) must have built in circuitry to ramp up the amperage it delivers according to what it considers to be safe/efficient. It would slow down as it came up to it full voltage. Ive never really worried about it much since i just plug it in at night and get through the day without needing a recharge. Years ago in RC you could buy batteries that could handle 2C and above charging rates pretty easily. I would imagine that number has increased. I figured phone batteries would essentially be the same.
Kounjula Rahul said:
Has any tried charging honor 5x with 2amp charger??
How much time does it took to charge fully..??
With stock 1amp it took 3hrs to charge fully....as i know snapdragon 615 nd 616 support quick charge 2.0...can it be utilized with 2amp charger??
Sent from my KIW-L22 using Tapatalk
Click to expand...
Click to collapse
I did not actually use the supplied 1A charger, but with a standard 1A charger it takes all night.
My tablet 2A charger is way faster (a few hours maybe), honestly I did not take note of the time.
I will try that.
The charger circuit will take care of it, no matter the available current, because tension is fixed to 5V so resulting current will be what the circuit handles.
Not sure about a quickcharge 2.0 charger, don't have one.
idk why i read that it takes them atleast 4-6 hours to fully charge their battery? ehh in an hour mine goes from 6% to like 67% and then the other 30 mins and its done and full. and im just using the charger and cable that came with the phone.
paoloroeseke said:
Good question. . I have a Qualcomm 2.0 fast charger at home, I'll plug mine into it and check the input
Click to expand...
Click to collapse
You did try your Qualcomm 2.0 fast charger adapter ?
I'm using mine with samsung fast charger (the one that came with my note5) and it charges from 70%-100% in 19mins...according to GSam app
htc fan89 said:
I'm using mine with samsung fast charger (the one that came with my note5) and it charges from 70%-100% in 19mins...according to GSam app
Click to expand...
Click to collapse
At that rate (30% in 20 min), it should take around 60 min to reach 80% and (80 min) 1hr 20 min to Fully Charge with that charger.
I swear the original reviews said it took around 2 1/2-3 hrs to charge overnight.
I have to say I have NEVER had a phone last as long as this phone does! The battery lasts forever no matter what I do.
cyrusalmighty said:
At that rate (30% in 20 min), it should take around 60 min to reach 80% and (80 min) 1hr 20 min to Fully Charge with that charger.
I swear the original reviews said it took around 2 1/2-3 hrs to charge overnight.
I have to say I have NEVER had a phone last as long as this phone does! The battery lasts forever no matter what I do.
Click to expand...
Click to collapse
I haven't manage to kill it yet, but it should take 1hr30mins to fully charge maybe less. That's with a fast charger
Sent from my KIW-L24 using Tapatalk
I keep wanting to test how long a full charge takes, using my intelligent Anker charger. I never get the chance. The phone battery life is simply outstanding. This is like my 8th smart phone, and simply blows the rest out of the water. I even have the EUMI battery saving features turned off. A 50% charge can takes about an hour. Old habits of always plugging it in when in the car or my desk means that I can forget about plugging it in at night. Don't worry about battery life or fast charging - they are non issues.
No QC2
I have tried two different adapters that are QC2 compatible (and work fine with Galaxy Note 4) with USB voltage measurement device; all I can get is 5V and 1A max even when the battery charges from 20% on.
So, no go on QC2
Also tried QC2.0 charger. No fast charging. However, Ampre, does report that it manages to pull 1.3A from the variable amperage ports i have.
I finally got my battery down to 0%. With Ampre reporting:
- Using a 0.5 amp charger, I got constant 460mA
- Using the 1.0 amp supplied charger I got 850mA
- Using my Anker 5A IQ charger (i think they license the QC technology) I only got 850mA. I checked and was using a power not data+power cable.
- Using same Anker 5A IQ charger, and a high quality power only Anker cable I got 1850 mA up until 50% charge then 1600 until 65% charge and 1200 until 85% charge. After that it dropped off rapidly 750 at 90%, and 450 at 95%.
Charging when using the phone lightly - occasional call, calendar update, email - consumes around 400 mA. I do not use any of the Honor power saving features. With this in mind:
- 40 min from 0 to 60%
- 1 hour 40 min from 0 to 90%.
Perfectly acceptable to me with the huge battery. GET RID OF YOUR CHEAP POWER CABLES
So IQ or QC chargers do seem to work, and most importantly make sure you have good quality power only cables. I have a drawer full of cables that were fine with older phones and chargers. They are now in the trash.
in china model support quick charge 2
in china model support quick charge 2
Bear100 said:
I finally got my battery down to 0%. With Ampre reporting:
- Using a 0.5 amp charger, I got constant 460mA
- Using the 1.0 amp supplied charger I got 850mA
- Using my Anker 5A IQ charger (i think they license the QC technology) I only got 850mA. I checked and was using a power not data+power cable.
- Using same Anker 5A IQ charger, and a high quality power only Anker cable I got 1850 mA up until 50% charge then 1600 until 65% charge and 1200 until 85% charge. After that it dropped off rapidly 750 at 90%, and 450 at 95%.
Charging when using the phone lightly - occasional call, calendar update, email - consumes around 400 mA. I do not use any of the Honor power saving features. With this in mind:
- 40 min from 0 to 60%
- 1 hour 40 min from 0 to 90%.
Perfectly acceptable to me with the huge battery. GET RID OF YOUR CHEAP POWER CABLES
So IQ or QC chargers do seem to work, and most importantly make sure you have good quality power only cables. I have a drawer full of cables that were fine with older phones and chargers. They are now in the trash.
Click to expand...
Click to collapse
+1 this is the same results I experienced. My phone rarely goes below 50% charge in a normal day
thanks guys, guess i'll get it - 120 on sale for prime day
starscalling said:
thanks guys, guess i'll get it - 120 on sale for prime day
Click to expand...
Click to collapse
worth the extra post - i can confirm the fast charging - was still doing about a percent a minute between 70% and 80% or so. little laggy during setup, occasionally seems to miss a command but dang for the price i can't complain.
using my zenfone2 fastcharger - rox.