I have a sprint s6 edge that I rooted but after i rooted it I flashed twrp recovery. Ironically it bricked my phone. I've tried using odin and I got this error: <ID:0/005> Complete(Write) operation failed.
Here's the whole log:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925PVPU1AOCF_G925PSPT1AOCF_G925PVPU1AOCF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Yes, I have all the drivers installed and all of that. I am new to this kind of stuff and I've seen people talk about pit files. I don't kno what those are so I don't know if that would help me. I've been trying to fix this for 3 months please help.
UNICORNSRDABEST said:
I have a sprint s6 edge that I rooted but after i rooted it I flashed twrp recovery. Ironically it bricked my phone. I've tried using odin and I got this error: <ID:0/005> Complete(Write) operation failed.
Here's the whole log:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925PVPU1AOCF_G925PSPT1AOCF_G925PVPU1AOCF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Yes, I have all the drivers installed and all of that. I am new to this kind of stuff and I've seen people talk about pit files. I don't kno what those are so I don't know if that would help me. I've been trying to fix this for 3 months please help.
Click to expand...
Click to collapse
Have you tried SmartSwitch its easier Then odin
osman34 said:
Have you tried SmartSwitch its easier Then odin
Click to expand...
Click to collapse
When I downloaded smart switch I got a side by side error. This happened on 2 different computers. I don't know how to fix it. I also tried using kies but I'm not sure how to get the s/n or imei.
UNICORNSRDABEST said:
When I downloaded smart switch I got a side by side error. This happened on 2 different computers. I don't know how to fix it. I also tried using kies but I'm not sure how to get the s/n or imei.
Click to expand...
Click to collapse
sboot.bin fail is the bootloader is older than your current one. Flash another firmware with a newer bootloader.
If you try smart switch you must fully close odin and phone still needs to be in download mode to do the emergency firmware recovery
callumbr1 said:
sboot.bin fail is the bootloader is older than your current one. Flash another firmware with a newer bootloader.
If you try smart switch you must fully close odin and phone still needs to be in download mode to do the emergency firmware recovery
Click to expand...
Click to collapse
So that means my odin is out of date or the stock firmware?
UNICORNSRDABEST said:
So that means my odin is out of date or the stock firmware?
Click to expand...
Click to collapse
the stock firmware has a older bootloader.
flash a firmware with newer bootloader.
callumbr1 said:
the stock firmware has a older bootloader.
flash a firmware with newer bootloader.
Click to expand...
Click to collapse
I'm still new to his stuff. What is a boot loader?
UNICORNSRDABEST said:
I'm still new to his stuff. What is a boot loader?
Click to expand...
Click to collapse
its part of the firmware package.
try to flash this firmware through odin
https://www.sammobile.com/firmwares/download/119909/G925PVPU4CPL3_G925PSPT4CPL3_SPR/
Related
Hi,
I'm trying to flash another firmware for my GIalaxy Note 10.1 N8000. I have read all tutorials etc. and prepared all according to it.
I was able to succesfully root to Clockwork Recovery so i though flashing another firmware to turn the Note into a European one instead of Chinese would be easy too. WRONG!!
Every time i want to flash with Odin it fails in the beginning of the process, see below:
Is there anyone who could comment me on what to do? I was able to recover from the failed flash attempt but i really want to flash another firmware from Europe for this Chinese version.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N8000XXCLL3_N8000OXECLL1_N8000XXCLL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> modem.bin
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried already two different Firmwares but both seem to fail at the same point. I only installed the USB drivers not KIES so i guess it is not the reason.
Any help what is going wrong or what i should try to do?
Thanks a lot far any help.
Dave
Even it is a generic question you might get an answer if you post it in the correct forum.
You are here in the Galaxy Tab 10.1 P7500/7501/7510/7511 forum! This is not for Galaxy Note 10.1 N8000.
davaze said:
Hi,
I'm trying to flash another firmware for my GIalaxy Note 10.1 N8000. I have read all tutorials etc. and prepared all according to it.
I was able to succesfully root to Clockwork Recovery so i though flashing another firmware to turn the Note into a European one instead of Chinese would be easy too. WRONG!!
Every time i want to flash with Odin it fails in the beginning of the process, see below:
Is there anyone who could comment me on what to do? I was able to recover from the failed flash attempt but i really want to flash another firmware from Europe for this Chinese version.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N8000XXCLL3_N8000OXECLL1_N8000XXCLL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> modem.bin
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried already two different Firmwares but both seem to fail at the same point. I only installed the USB drivers not KIES so i guess it is not the reason.
Any help what is going wrong or what i should try to do?
Thanks a lot far any help.
Dave
Click to expand...
Click to collapse
BeeGee_Tokyo said:
Even it is a generic question you might get an answer if you post it in the correct forum.
You are here in the Galaxy Tab 10.1 P7500/7501/7510/7511 forum! This is not for Galaxy Note 10.1 N8000.
Click to expand...
Click to collapse
Ooops, sorry my mistake! Moved it already.
Thanks.
So yeah, for some days ago i have installed a custom rom this one : Leaked Android 4.2.2 XXUFME3 ROM for Galaxy S III
it worked fine but i wanted to get back to stock rom.
So i downloaded a stock rom ( for nordic countries )
After this i re partioned my s3, i used a file for 16 gb cause its my model. after this the phone turned on and i saw samsung galaxy s3 logo blincking, nothing else heppend. But i knew i wasnt done and took the battery out and back, and entered download mode.
Now i chosed a rom with PDA button, i unchecked re partion and hited start button. Odin was stuck at "setup connection".
I have installed and reinstalled drivers, installed and uinstalled kies, i have tried this on all of my usb ports, i tried this on my other pc with installed drivers etc. Nothing WORKS!!!! i am a noob with Android and really need a help. i Have working to get it work 4 hours and nothing...
Btw i have no sd card in my s3.
It looks like i dont have any firmware on my phone now, but i can still enter download mod, but not recovery mod.
What can i do??
Reads as you may have bricked your phone as you have for some unknown reason repartitioned it ..
install stock rom via Odin and post the Odin results .
jje
JJEgan said:
Reads as you may have bricked your phone as you have for some unknown reason repartitioned it ..
install stock rom via Odin and post the Odin results .
jje
Click to expand...
Click to collapse
omg... now odin cant see my phone...., but it was always stuck at setup connection, or the odin have stoped working. I will reset my pc and post result.
kris222 said:
omg... now odin cant see my phone...., but it was always stuck at setup connection, or the odin have stoped working. I will reset my pc and post result.
Click to expand...
Click to collapse
no need to reset your pc. change the usb port and check it. there's no need for you to panic.
sriram231092 said:
no need to reset your pc. change the usb port and check it. there's no need for you to panic.
Click to expand...
Click to collapse
okey i have pluged it to another computer and now it comes up in odin. but it wont install . here
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9300_NEE_I9300XXALE8_I9300NEEALE3_I9300XXLE8.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
and here it ends..... after like 20 min the message comes up and says that 0 complited 1 failed. so what now?
kris222 said:
okey i have pluged it to another computer and now it comes up in odin. but it wont install . here
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9300_NEE_I9300XXALE8_I9300NEEALE3_I9300XXLE8.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
and here it ends..... after like 20 min the message comes up and says that 0 complited 1 failed. so what now?
Click to expand...
Click to collapse
did you do everything as mentioned in this site? http://androidromupdate.com/2012/06...ung-galaxy-s3-gt-i9300-stock-rom-i9300xxale8/
i did!
the only thing i did wrong was to re partition it......
now i dont know how to get it work...
Try flashing again but with the newest ROM from NEE, if flash successful, probably will boot loop again, enter to recovery mode and do a factory reset.
http://forum.xda-developers.com/showthread.php?t=1646610 2nd post.
Good luck
Regards
[email protected]
You'll need to re-partition now! You probably screwed pit partition!
Try with another pit file and make sure its a legit one!
Sent from my GT-I9300 using xda premium
Ver3go said:
You'll need to re-partition now! You probably screwed pit partition!
Try with another pit file and make sure its a legit one!
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
Hi i downloaded pit file for 16 gb model. After instlling it it said pass (green) on odin. After this i i tried to install the stock rom, but it failed....
Here is log of Odin :
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Completed..
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXEMD2_I9300OXXEMD1_I9300XXEMC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Help???
anyone??
kris222 said:
Hi i downloaded pit file for 16 gb model. After instlling it it said pass (green) on odin. After this i i tried to install the stock rom, but it failed....
Here is log of Odin :
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Completed..
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXEMD2_I9300OXXEMD1_I9300XXEMC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Help???
Click to expand...
Click to collapse
Do all in one thick re-partition! And put the pit. And choose pda with your rom
Sent from my GT-I9300 using xda premium
Pretty fun that non experienced people are flashing stuffs, rooting etc etc without reading two or three times before so they learn about what could happen if anything are done the wrong way..
In worst case, warranty is the only solution to fix this and re-program PIT layering of your phone. It may cost if there is any sign of modifications / flash counter above zero...
Sent from my GT-I9300 using xda app-developers app
Go to http://forum.xda-developers.com/showthread.php?t=1944196 post #6
Regards
[email protected]
So there is nothing i can do? just go to service....?
And because i have installed custom rom i have no waranty.... is it expensiv to fix?
btw i heard of a 3 part rom with mx.pit, would it help or would it make it wors?
?????
kris222 said:
So there is nothing i can do? just go to service....?
And because i have installed custom rom i have no waranty.... is it expensiv to fix?
btw i heard of a 3 part rom with mx.pit, would it help or would it make it wors?
Click to expand...
Click to collapse
Your phone is dead sure worst wont do
Sent from my GT-I9300 using xda premium
I think they will repair it for free
Sent from my washing machine using xda premium
Hello I have a Galaxy s6 edge from videotron SM-G925W8 I've try to rooted it today , but now I'm cought in a bootloop , I've try to flash it back with the original Videotron firmware but Odin give me this error at the beggening
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925W8VLU1AOCG_G925W8OYA1AOCG_G925W8VLU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Does anyone know what should be my next step ?
imanu said:
Hello I have a Galaxy s6 edge from videotron SM-G925W8 I've try to rooted it today , but now I'm cought in a bootloop , I've try to flash it back with the original Videotron firmware but Odin give me this error at the beggening
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925W8VLU1AOCG_G925W8OYA1AOCG_G925W8VLU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Does anyone know what should be my next step ?
Click to expand...
Click to collapse
Did you try wiping the cache partition?
Snowby123 said:
Did you try wiping the cache partition?
Click to expand...
Click to collapse
yes and its not working
http://forum.xda-developers.com/galaxy-s6-edge/help/5-1-1-manual-update-stuck-g925f-t3173112
This thread describes a similar issue.
The user tried flashing the stock firmware through Odin; it bricked the phone.
If you read through it you will see how the issue was resolved.
Thanks , but its for G925F version ? what do I need to do since its not the same version?
Now that is another conundrum I wasn't prepared for. I know that half of the tutorial on that thread is compatible with your phone; half is exclusive to G925F.
---------- Post added 13th August 2015 at 12:06 AM ---------- Previous post was 12th August 2015 at 11:50 PM ----------
I found another thread that explains how to troubleshoot a failed Odin attempt.
It is written for the Galaxy S2, but sounds generalized for all Samsung Galaxies.
http://forum.xda-developers.com/galaxy-s2/general/guide-t2345831
If you have access to download mode, you're ok but in order to reduce to a minimum the things that might go wrong, you should:
1- Use odin 3.10.6
2- verify the integrity of the firmware downloaded on sammobile. It should be roughly 3,402,561 kb in size
3- make sure you have Samsung Android drivers installed
4- If all above fails, switch USB cable, and then USB port
If you still have an issue, try downloading the odin flashable TWRP and try to flash it, if it passes, try wiping everything on the phone in TWRP and try the process again
As a last resort, you can try to see if KIES emergency firmware installation will work. If after doing all this you're not back up and running, you're screwed but i doubt you will have failed all of the above.
at first.. you need a custom kernel to root 5.1.1 because of the new system write protection..the second i think you are on reactivation look..look in my twrp thread for more
You got error on sboot.bin due to your flashing bootloader version lower than your device bootloader try to get the latest firmware or flash a custom firmware
If you need further assistance contact me via pm
Sent from my SM-G925F using XDA Free mobile app
I tried newest uk beta (BTU) recently and i wasn't happy about the battery etc.
Flashed newest lollipop firmware for NEE csc. I have tried so many firmwares and no luck .. :crying:
Do i miss something big time? and i am 100% sure about that firmware is right.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925IDVU2COF8_G925IODD2COF8_G925IDVU2COF8_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Getting this kind of log from odin. note this is copy from another thread, otherwise same but buildnumber is different..
I can't even flash twrp/philz recovery. without getting some error, PIT related.
I can't access recovery by anymeans as it wil boot up to that ''smart switch blablabla'' and pc will say it is not supported etc.
I only can access download-mode.
I have tried flash stock 5.1.1 PIT but it makes no difference.
This is 32gb model. How deep i'm in brown?
Got this working!
First i used odin 3.10.7 -> all fails
Then tried 3.10.6 -> first try successfully only that hidden.img was failed but i extracted from firmware and and flashed it after that.
Hope this helps someone.
if you had used smart switch on your pc, it was a lot easier............:good:
lambik333 said:
if you had used smart switch on your pc, it was a lot easier............:good:
Click to expand...
Click to collapse
Maybe if i would done it in first place, but i didnt. Used odin as it usually will do job. And this case smart switch didnt reconized phone at all. :good:
my s3(i9305) is stuck in download mode with stock recovery on it and ive got odin, but i cant get any stock roms booted on it, cant get onto the phone, and it dont have any working firmware on it...i just want to put it back to stock asap and get the dam thing working again.
any help would be great!!
What output are you getting in odin?
Beamed in by telepathy.
shivadow said:
What output are you getting in odin?
Beamed in by telepathy.
Click to expand...
Click to collapse
the bar is blue
No, there is a 'window' on the bottom left of the app with text in it. What does that text say when you've attempted to flash the phone?. Need all of it, not just the result at the end.
The blue bar means the flash completed successfully but doesn't give any more info than that.
Beamed in by telepathy.
shivadow said:
No, there is a 'window' on the bottom left of the app with text in it. What does that text say when you've attempted to flash the phone?. Need all of it, not just the result at the end.
Beamed in by telepathy.
Click to expand...
Click to collapse
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGPE1_I9300AMNGPF1_I9300BVUGNB2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Sboot.bin is the bootloader so I presume that it is either locked or corrupt. I'm not sure if that is a pit error or not. You could try to find another file and hope it works but if you're absolutely sure the one you have is good then there's no point. You could try finding a stock rom that doesn't include the bootloader. Also flashing a pit file (only as a very last step) is an option but make sure it is the correct one for your specific model and region etc.
I hate recommending pit file flashing but in this case it could be viable from other reports around the site. Flashing a pit file is a last resort only, I cannot stress this enough.
Beamed in by telepathy.
shivadow said:
Sboot.bin is the bootloader so I presume that it is either locked or corrupt. I'm not sure if that is a pit error or not. You could try to find another file and hope it works but if you're absolutely sure the one you have is good then there's no point. You could try finding a stock rom that doesn't include the bootloader. Also flashing a pit file (only as a very last step) is an option but make sure it is the correct one for your specific model and region etc.
I hate recommending pit file flashing but in this case it could be viable from other reports around the site. Flashing a pit file is a last resort only, I cannot stress this enough.
Beamed in by telepathy.
Click to expand...
Click to collapse
where might i find a stock rom without a bootloader? dont fancy the pit file tbh!!
Try using different USB cables and USB 2.0 ports.
audit13 said:
Try using different USB cables and USB 2.0 ports.
Click to expand...
Click to collapse
ive only got the 1 usb port on my tablet
The sboot.bin is not flashing because the bootloader on the phone is newer than the bootloader in the ROM you are flashing, the ROM is not for your phone, and/or you need to try another computer.
It's unlikely that the bootloader is locked as AT&T and Verizon are the only two carriers I know of who lock down the bootloader.
i'm totally out of my knowledge zone here....i did do thison 1 of my old phones a few years back and some one wrote on a comment exactly how to make it stock again....but i'm buggered if i can find that post again....or thats even if the site still has that thread...can anyone point me in the right direction here please?
Ok this is what i get when i try and flash this:I9300XXUGNB5_I9300EVRGML2_EVR
which i got from sam pass and selected my exact model of phone from my country(uk) and the network i'm using....with odin v3.10
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGNB5_I9300EVRGML2_I9300BVUGNB2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> modem.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
can someone please tell me what i'm doing wrong??
so this is what i'm getting when i'm using odin v3.10 trying to install the correct firmware for my phone from sam pas and selecting the country/network
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGNB5_I9300EVRGML2_I9300BVUGNB2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> modem.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
can someone please point me in the right direction??
Your original post says the phone is a 9305 and you are flashing a 9300 ROM?
yea i'm trying to download I9305XXUFOC1 now but every site i go to its giving me a 5 hour wait time.....is there a faster way i can get it downloaded?
audit13 said:
Your original post says the phone is a 9305 and you are flashing a 9300 ROM?
Click to expand...
Click to collapse
Well spotted, didn't even occur to me..
Beamed in by telepathy.
In use sammobile.com. The download speed for free accounts is not great but I usually start the download and do something else for a while.