Guys I flashed my SM-G531H / DL whit this Fiemware (G531HVJU0APC2_G531HZTO0APC1_G531HUBU0APC1)
and now I have this problem,my Phone is brick can you tell me what Firmware can I use to Desbrick my phone?
thx in advance.
It say that After the flash with odin and this Rom
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> SPRDCP.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
pacoelo said:
Guys I flashed my SM-G531H / DL whit this Fiemware (G531HVJU0APC2_G531HZTO0APC1_G531HUBU0APC1)
and now I have this problem,my Phone is brick can you tell me what Firmware can I use to Desbrick my phone?
thx in advance.
Click to expand...
Click to collapse
Are you sure it is the correct firmware?
You can try this link i created a thread about fail after hidden.img but u can try the something instead of doing steps on hidden.img do for SPRDCP.img. if u dont understand ask me
https://forum.xda-developers.com/grand-prime/help/guide-odin-failed-flashing-stock-t3514810
Becareful
Maybe is baseband G531HUBUAOJ2
Related
Ok just tried to go from cm10.1 to stock but now I'm stuck in a boot loop and I have no idea what to do, here the what Odin said:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXELLA_I9300H3GELL1_I9300NELK2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> system.img
<ID:0/003> NAND Write Start!!
<ID:0/003> boot.img
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> recovery.img
<ID:0/003> modem.bin
<ID:0/003> tz.img
<ID:0/003> sboot.bin
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
I can go in to download mode if that helps..
I think I found a solution but I'm in the middle of doing it now will post if it worked
http://forum.xda-developers.com/showthread.php?p=38780087#post38780087
You'll have to go to recovery and wipe data. That'll remove everything from the internal SD card, of course, but the phone will boot up. I faced this issue little while ago. This solved it.
Sent from my GT-I9300 using xda app-developers app
read the basics. you have to wipe data when switching ROMs. flash a custom recovery via Odin and wipe data from there, so that it doesn't wipe your internal sd
Hello everybody. I have a Samsung Galaxy S4 factory unlocked.
A week ago I rooted my phone and changed the firmware to an Android Google Play Edition 4.4 Kitkat. Now, I would like to return to the official stock version. I downloaded the firmware from sammobile and other sources. When I try to flash using Odin, always get a FAIL. This is the ODIN messages history.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMK9_I9505VFGEMK2_I9505XXUEMK9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
I tried changing the USB port, uninstalling and instaling Kies, I used different root files, even I used a PIT file, following the steps in this thread (http://forum.xda-developers.com/showthread.php?t=1727443). I already check kies is not running on background. I tried with different Odin version (1.85, 3.04, 3.07 & 3.09)
I dont know how to fix this problem. Please if anyone can help me I really appreciate.
Thank you so much for all your replies.
Hey all,
My sch-i545 is stuck in download mode, cannot boot. I want to delete everything and start over.
I downloaded the stock 5.0.1 rom, which what i believe was on it before it soft bricked, and every time I try to run odin with the md5 the program becomes unresponsive. Any ideas???
Download this one. It's official stock:
ODIN v3.10:
https://drive.google.com/file/d/0B4RU_ZH5QUASNmxLX3JpejBXREE/view?usp=docslist_api
OC1 image:
https://drive.google.com/file/d/0B4RU_ZH5QUASaU9LcDJ3WWZfdXM/view?usp=docslist_api
Sent from my SCH-I545 using Tapatalk
Thank you for the file. so this time it does not crash odin, but now it says complete write operation failed.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_VZW_I545VRUGOC1_I545VZWGOC1_CL4584173_QB4517016_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Try to use 3.09. It's the only one that worked for me.
Odin 3.0.9 seems to work better, but it fails at a certain point per below.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_VZW_I545VRUGOC1_I545VZWGOC1_CL4584173_QB4517016_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> persdata.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Any thoughts? :-\
You'll want to flash the first link in this one:
http://forum.xda-developers.com/gal...pment/odin-i545vrugoc1-factory-image-t3160125
What you are trying to flash is a ROM someone put together I believe. It's not the exact factory image and is probably not wiping all the bad files.
Thank you for the help so far, but I still have the same problem with writing. It fails after about 7 minutes.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I545VRUGOC1_I545VZWGOC1_I545VRUGOC1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Any ideas? :-\
Download the PIT file and flash that along with the ROM
Sent from my draconis using Tapatalk
I have a pit file from December 2013, the only one I could find. Still have no luck getting it to flash when using that PIT
Any ideas?
Nanometer45 said:
Any ideas?
Click to expand...
Click to collapse
Are you using the stock USB cable you know the Samsung one?
I tried 3 different cables. the one that worked? The USB cable I just got for my S6. Thanks for your help!
I have Gear S TMobile version (R750T) .. I was trying to flash stock firmware (R750TUVU1AOA7_R750TTMB1AOA7_TMB) but is stopped and gave me this message
Firmware upgrade encountered an issue
Please select recovery mode in kies and try again
tried kies with no luck ... trying to connection :crying::crying::crying:
any hope ???
here is the Log
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> dzImage
<ID:0/003> dzImage-recovery
<ID:0/003> modules.img
<ID:0/003> rpm.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> sdi.mbn
<ID:0/003> tz.mbn
<ID:0/003> rootfs.img
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Screen shot
Update :
Tried to flash it with another firmware ... Now I'm stuck with Bootloop !!!!!
Please help
I am trying to fix a S6 edge. The problem is that when i boot it up it shows me "an error has occurred while updating the device software"
Odin, newest version, does not see the phone. I have searched around and downloaded the G9250ZTU2COKB_G9250ZZT2COKB_BRI firmware for my SM-G9250 and trying to flash it with Odin 3.10.7
It starts but soon after starting it shows me the following error. Any help please? I have searched and found a thread where it says that i need to remove the hidden image from the file but there is no hidden image in it after extracting the tar file.
TIA
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Removed!!
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
try flashing the XEU or BTU firmware.
mikey_sk said:
try flashing the XEU or BTU firmware.
Click to expand...
Click to collapse
DON'T do this ^ - your 9250 is a different hardware variant to the 925F/I/T etc models and if you flash a non-9250 firmware you'll likely end up with a paperweight.
Anyone else with any ideas?