Hi, my device suddenly stopped working, I kept it to charge over night and in the morning, problem started
So i ordered a new battery but still nothing.
I think that phone is bricked
Simply no response, twrp or fastboot, nothing
The problem is that i need my data from the phone, i have set backup every friday it hapened in thursday - so i will loose som of my data
What i should use? SP flash tool or MI flash tool, or chinese miracle?
Repair me if i wrong with something.
When i unplug the battery. phone will connect to PC but after few seconds it will automaticaly disconnect,
I've installed Mediatek DA USB VCOM drivers - but there is yellow triangle when i connect phone to PC it will recognise it as - Mediatek USB port
Thanks for any help.
Related
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Once the red line loads, try putting back the battery. Sometimes the handset needs power from the battery. I did that with my HT3: once SP Flash Tool detected my phone, I put the battery back.
I have this Lenovo A328 which suddenly had multiple and continuous gallery crashes. I tried to do a factory reset but get bootloop.
I decided to flash the stock rom using SP Flash Tool. The battery was charged ~ 50% Flashing the stock rom i always get s_da_mt_dedicated_pattern_error (3094) After 2-3 attempts nothing changed, still bootloop. After the next 2-3 attempts the phone stopped turning on and charging. I assumed that the case is in a discharged battery. It was really in her. The battery discharged to 3 volts so i asked my friends to charge it.
After the battery has been charged nothing has changed, the phone still does not turn on or vibrate.
Using SP_Flash_Tool_v5.1352.01, I formatted the flash. I downloaded the Lenovo A328 ROW_S322_140822 and flashed it. The result is OK, but the phone still does not turn on or charge. I tried every possible combination: format all+download, download only, auto format flash, manual format flash.
Any idea on this one?
Software & Firmware used:
SP_Flash_Tool_v3.1336.0.198
SP_Flash_Tool_v5.1352.01
SP_Flash_Tool_exe_Windows_v5.1520.00.000
SP_Flash_Tool_v5.1516.00
A328_ROW_S329_150708
A328_ROW_S324_141116
Lenovo A328 ROW_S322_140822
Hello everyone!
I am facing the same problem!!! After apps crashing, no start, no charge.... PC can see the phone in device manager under Win 10/ Win 7... (MTK usb port and MTK vcom preloader port)
Tried almost all the solutions suggested on different sites or forums, nothing works, still no charge and no start...
Change the PC, the USB cables, drivers, ROM's, you name it... Someone said this MTK devices are hard to brick but still, why we cannot revive our devices??? Hardware failure? Not really according to some technicians as long your phone is detected by the pc in device manager, the phone CAN be "unbricked".
SO, we are missing something, we doing something wrong???
We need help.... SOMEONE???
Hey, I got wiko ridge 4g that was bricked, it won't turn on but the light is blinking when battery is not full when i connect him on charger. I have connected the phone with PC via USB and he recognized him as 'qhsusb_bulk', i tried to unbricked it with SRK Tool 2.0, but i can't turn on usb debbuging and i don't know if the phone is rooted or not, but i did it anyway. So i managed to delete partitions with that program, but later the phone was recognized as Unknown USB Device. So my question is : is there any other way to brick the phone back, without phone being turned on, via PC ?
Thank you very much.
muki22 said:
Hey, I got wiko ridge 4g that was bricked, it won't turn on but the light is blinking when battery is not full when i connect him on charger. I have connected the phone with PC via USB and he recognized him as 'qhsusb_bulk', i tried to unbricked it with SRK Tool 2.0, but i can't turn on usb debbuging and i don't know if the phone is rooted or not, but i did it anyway. So i managed to delete partitions with that program, but later the phone was recognized as Unknown USB Device. So my question is : is there any other way to brick the phone back, without phone being turned on, via PC ?
Thank you very much.
Click to expand...
Click to collapse
Hm, nobody answered to this ,so i keep digging out on internet,and after some searching i use the qfil app, also i downloaded original stock rom for my wiko ridge 4g, through qfil i installed that rom , the pc in one point recognized my device as 4g ridge, but then just started to showing quallcomm hs-usb diagnostic mode 9092 when it connected to PC via USB. My phone show some signs ,screen was black but it vibrating, and a assume it's turned on when i press touch screen or volume changer button he reproducing sound, but on pc he is readed like quallcomm hs-usb diagnostic mode 9092! If somebody know how to fix that problem, please answer me!
Hello following this guide (http://en.miui.com/thread-193681-1-1.html) i tried to revive my phone but now he wont turn on and when i connect it to my PC it either connects/dissconects over and over again or windows says that the usb port was not recognised. I tried charging the phone for 24 hours but the phone doesnt react to charger and it didnt help. Any idea what might be going on?
Hey guys, i am hoping someone can help me.
I have bricked my phone, no recovery, no fastboot, nothing, just vibrations and notification led. So i managed to open up phone and to disconnect battery.
Next thing i installed lattest sp flash tool v5.1952, and i found authentication file on xda. I downloaded 11.0.7.0 global image, and use Android_scatter file from there. I installed both drivers for mediatek preload one and vcom drivers, and rebooted my phone.
So i turned the phone off, by disconnecting battery, pressed start on sp flash tool, connected the phone via usb cable, but nothing is happening. I also tried while phone was on but same thing.. Have anyone have same issues, can somebody help me please?
You will need a authorized mi account if u have can you please help me