Related
I accidentally flashed the wrong recovery image on my karbonn a4+ using mobileuncle tools . The phone is stuck in recovery mode and I am unable to make a selection in recovery. How can I flash the correct version of stock recovery. i cant factory reset in my phone. plz give a solution ......
i want to flash stock recovery or cwm recovery for karbonn a4+
Tried removing the battery?
Can you get into fastboot?
DopeyTheOne said:
Tried removing the battery?
Can you get into fastboot?
Click to expand...
Click to collapse
i tried to removing battery but only black screen on recovery mode
and i cant get into fastboot
is there way to install cwm recovery on karbonn a4+? (mt6577 hardware)
Red ngsTax
i tried to removing battery but only black screen on recovery mode
and i cant get into fastboot
is there way to install cwm recovery on karbonn a4+? (mt6577 hardware)
Click to expand...
Click to collapse
Ok, let's troubleshoot some more
When you connect thru usb, does the pc picks anything up? There are ways to check....via the command adb devices in cmd (make sure you have SDK installed), if it says "no devices detected" you should check the devicemanager to see if there's an unknown driver found (they usually pop out the tree with an ! behind it.
---------- Post added at 09:17 AM ---------- Previous post was at 08:47 AM ----------
i tried to removing battery but only black screen on recovery mode
and i cant get into fastboot
is there way to install cwm recovery on karbonn a4+? (mt6577 hardware)
Click to expand...
Click to collapse
Ok, let's troubleshoot some more
When you connect thru usb, does the pc picks anything up? There are ways to check....via the command adb devices in cmd (make sure you have SDK installed), if it says "no devices detected" you should check the devicemanager to see if there's an unknown driver found (they usually pop out the tree with an ! behind it.
mobile is repaired at karbonn care service :laugh:
the correct stock recovery is flashed
thnks for reply :good:
can u plz upload stock recovery img of karbonn a4+ my too recovery corrupted.. help me out
Happened to me too, but I later flashed using another toolkit and it worked!
Hey, Can u post your boot and recover image.. i strucked in similar problem... as am in outside india.. i can t go karbonn servicecenter.
OK So... I decided to root my TF103c (K010) so I remove some of the stupid crapware that asus has installed and I gained root fine and went ahead and started removing stuff. But apparently I removed something I shouldn't have and now I'm constantly getting Asus Services has stopped messages and I can't actually do anything with the damn thing. Because it has such a crap locked down recovery and bootloader etc. I can't seem to find any easy way around this. As in I can't just load all the things I uninstalled from the backups because I can't use ADB with the device. (Yes it WAS turned on in the settings until I formatted cache and data in case that might fix it... it didn't)
Does anybody have any advice?? Coz I'm stumped...
fastboot
RaVe-N said:
OK So... I decided to root my TF103c (K010) so I remove some of the stupid crapware that asus has installed and I gained root fine and went ahead and started removing stuff. But apparently I removed something I shouldn't have and now I'm constantly getting Asus Services has stopped messages and I can't actually do anything with the damn thing. Because it has such a crap locked down recovery and bootloader etc. I can't seem to find any easy way around this. As in I can't just load all the things I uninstalled from the backups because I can't use ADB with the device. (Yes it WAS turned on in the settings until I formatted cache and data in case that might fix it... it didn't)
Does anybody have any advice?? Coz I'm stumped...
Click to expand...
Click to collapse
are you still having problems? do you have a pc with adb installed and or fastboot?
---------- Post added at 12:19 PM ---------- Previous post was at 12:09 PM ----------
majored said:
are you still having problems? do you have a pc with adb installed and or fastboot?
Click to expand...
Click to collapse
ok well open a command window or if you have windows you can use powershell type adb devices enter anything? If that got you nothing while the device is powered on then power off device . With the device off press and hold vol up and power btton when device powers on release power button but continue holding vol up. if its charging the battery icon can mess this process up so unhook your device if your having problems you should boot to droidboot (aka FASTBOOT) where your adb commands will simply start Ex. fastboot devices it should read your device.
---------- Post added at 12:26 PM ---------- Previous post was at 12:19 PM ----------
majored said:
are you still having problems? do you have a pc with adb installed and or fastboot?
---------- Post added at 12:19 PM ---------- Previous post was at 12:09 PM ----------
ok well open a command window or if you have windows you can use powershell type adb devices enter anything? If that got you nothing while the device is powered on then power off device . With the device off press and hold vol up and power btton when device powers on release power button but continue holding vol up. if its charging the battery icon can mess this process up so unhook your device if your having problems you should boot to droidboot (aka FASTBOOT) where your adb commands will simply start Ex. fastboot devices it should read your device.
Click to expand...
Click to collapse
Well what i did was flash a recovery not compatible with my k010 but this did not stop me from booting to droidboot however my stock recovery for now is gone . my device was doing this too had about minute or so once powered on till it crashed. MY BLUETOOTH Went out and in my settings the on off would slide back and forth till it crashed but best buy sold me a 40$ one year warranty SUCKERS and asus installed a new one
majored said:
are you still having problems? do you have a pc with adb installed and or fastboot?
---------- Post added at 12:19 PM ---------- Previous post was at 12:09 PM ----------
ok well open a command window or if you have windows you can use powershell type adb devices enter anything? If that got you nothing while the device is powered on then power off device . With the device off press and hold vol up and power btton when device powers on release power button but continue holding vol up. if its charging the battery icon can mess this process up so unhook your device if your having problems you should boot to droidboot (aka FASTBOOT) where your adb commands will simply start Ex. fastboot devices it should read your device.
---------- Post added at 12:26 PM ---------- Previous post was at 12:19 PM ----------
Well what i did was flash a recovery not compatible with my k010 but this did not stop me from booting to droidboot however my stock recovery for now is gone . my device was doing this too had about minute or so once powered on till it crashed. MY BLUETOOTH Went out and in my settings the on off would slide back and forth till it crashed but best buy sold me a 40$ one year warranty SUCKERS and asus installed a new one
Click to expand...
Click to collapse
Thanks for the reply.
I have a adb and fastboot but most of the commands just don't work. I tried to remotely install apks but that fails. I tried to side load the latest FW downloaded from ASUS but it fails the certificate check. Basically I'm just waiting for the next system update to come OTA and I'll try flashing that... No idea when that will be of course...
Thanks for trying to help though.
Flashing Firmware using DROIDBOOT:
Instructions: https://drive.google.com/file/d/0B_JkvfrnO7pXMzVaZEM5OFF2ZGM/view
Download: https://yadi.sk/d/fduOPFuhes3dC or https://drive.google.com/file/d/0B_JkvfrnO7pXSHc1RGhzak1DN2c/view
(Fastboot incudled, partitions images in .img format, adb incudled, but not needed)
i dont have runned update_image.bat. i needed only recovery and system.
fastboot flash recovery recovery.img
fastboot erase system
fastboot flash recovery recovery.img
fastboot flash system system.img
but you need to find some fastboot drivers for tablet.
i have used intel soc. drivers. but yet i dont have download link.
just google search to TF103C fastboot/driodboot drivers.
where's firmware
RaVe-N said:
Thanks for the reply.
I have a adb and fastboot but most of the commands just don't work. I tried to remotely install apks but that fails. I tried to side load the latest FW downloaded from ASUS but it fails the certificate check. Basically I'm just waiting for the next system update to come OTA and I'll try flashing that... No idea when that will be of course...
Thanks for trying to help though.
Click to expand...
Click to collapse
whare did you find firmware on asus site. i go to support and all i see is Kernel Code and manuals.
---------- Post added at 03:00 PM ---------- Previous post was at 02:55 PM ----------
Ok I fastboot flash 2.2.33.138. with no help from asus. but jacky_cao <[email protected]> got this reply i suggest you to contact the RMA center again . they will help you to update the firmware to (FW_WW_TF103C-2.2.33.144-release-user-20150827-signed.zip ) manually. But can't tell me how to contact anybody to help do that. does anybody here have the files needed to ota up to 144?
Guys, I followed the instructions from gouster3, but my Asus still hangs up during the boot. I just see the logo ASUS In search of incredible and that is it.
I too had a problem having foolishly erased an apparently needed system app after rooting. After many hours off and on of trying to sideload the latest firmware from ASUS i finally found this thread and success.
1) Of course put device in DROIDboot (fastboot). From power off, reboot tablet holding power + vol up for 2-3 seconds.
Per Post #4
[Cannot post url due to restrictions, get links from post #4. use the 2nd link in post, first link is dead]
(Fastboot included, partitions images in .img format, adb included, but not needed)
unpack zip and launch adb. (i already had an install of minimal adb and fastboot so I only moved boot, recovery, system, droidboot, flash, partition.tbl and AS-TF103C-v67.43-capsule.bin to that folder and launched from there. In hindsight I only probably needed system, flash, partition and capsule and might not have needed anything but system...)
fastboot erase system
fastboot flash system system.img
This takes a few minutes in which it appears nothing is happening... and then system is sent in 3 chunks.
Upon launch process.google.apps or something kept crashing and I could not log into google, but a reset from within the OS fixed that and I was back in business. I probably should have loaded recovery and cleared the cache and such and then rebooted, but i got hasty.
Anyway I know this is an old problem and people have probably moved onto other things, but for someone like me who has had this once wonderful device sitting around waiting for a new breathe of life and the energy to take another stab at it out, don't give up. And thanks to all the gurus here for all the help over the years...
gouster3 said:
Flashing Firmware using DROIDBOOT:
Instructions: https://drive.google.com/file/d/0B_JkvfrnO7pXMzVaZEM5OFF2ZGM/view
Download: https://yadi.sk/d/fduOPFuhes3dC or https://drive.google.com/file/d/0B_JkvfrnO7pXSHc1RGhzak1DN2c/view
(Fastboot incudled, partitions images in .img format, adb incudled, but not needed)
i dont have runned update_image.bat. i needed only recovery and system.
fastboot flash recovery recovery.img
fastboot erase system
fastboot flash recovery recovery.img
fastboot flash system system.img
but you need to find some fastboot drivers for tablet.
i have used intel soc. drivers. but yet i dont have download link.
just google search to TF103C fastboot/driodboot drivers.
Click to expand...
Click to collapse
THANKS I bricked my tf103c and this fixed it and got it working again
Do you have any easy guide on installing a custom rom to this device in this way?
I use Zenfonerootkit_20150528 to root the device and it works fine
I just can never find a rom or such or guide on this :/ ( i found this old device and thought i would have a mess with it)
I
Hello everyone
I hope you all are around I really need your help at it again, I have got an asus tf 103c i tried to root it and now I get a bootloop i tried everything but failed. Please I know you will be angry because you already explained everything but I am a verry beginner and also many links are dead I need your help.
Thank you from advance
I accidently flashed wrong CWM recovery to my phone...
Now its went to boot loop....:crying::crying::crying::crying:
When I power on phone by pressing Vol Down + Power button it shows Fastboot mode in Mobile Screen at the Buttom edge...
But When I tried in Command Prompt with "fastboot devices" its dont show my device.... as well as "adb devices"
Some one please tell me How to flash my phone with orginal recovery.... Please....
tigerdhana1371102 said:
I accidently flashed wrong CWM recovery to my phone...
Now its went to boot loop....:crying::crying::crying::crying:
When I power on phone by pressing Vol Down + Power button it shows Fastboot mode in Mobile Screen at the Buttom edge...
But When I tried in Command Prompt with "fastboot devices" its dont show my device.... as well as "adb devices"
Some one please tell me How to flash my phone with orginal recovery.... Please....
Click to expand...
Click to collapse
hi, see attach file. translate it with google
you need to find original stock rom (try needrom.com)
next time do not try to flash CWM to your infocus.
good luck
Thank you for the help Bro... But please tell me few more details...
yosi s said:
hi, see attach file. translate it with google
you need to find original stock rom (try needrom.com)
next time do not try to flash CWM to your infocus.
good luck
Click to expand...
Click to collapse
I am on trying it.....
Can you please tell me how to flash it with stock rom?
Should I use SP flashtool or something other???
Please....
and when I use Vol + button and power button combination its still getinto bootloop
but when I use Vol - Button and power button its getinto fastboot mode(in the lower left cornet it shows "=>Fastboot mode..." message....
I updated the taiwan101 recovery by using mobileuncle tools earlier....
and for solution I tried to take backup of another M2 3G phone's recovery.img and I tried to flash it via fastboot
the command i used to flash
"fastboot -i 0x0489 flash recovery recovery.img"
But its give me a error like in picture...
help
TigerDhana017 said:
I am on trying it.....
Can you please tell me how to flash it with stock rom?
Should I use SP flashtool or something other???
Please....
and when I use Vol + button and power button combination its still getinto bootloop
but when I use Vol - Button and power button its getinto fastboot mode(in the lower left cornet it shows "=>Fastboot mode..." message....
I updated the taiwan101 recovery by using mobileuncle tools earlier....
and for solution I tried to take backup of another M2 3G phone's recovery.img and I tried to flash it via fastboot
the command i used to flash
"fastboot -i 0x0489 flash recovery recovery.img"
But its give me a error like in picture...
Click to expand...
Click to collapse
hi TigerDhana017 were u able to flash the stock rom from needrom.com? plz reply soon.i'm in dire state
thanx in advance
gauravinvouge said:
hi TigerDhana017 were u able to flash the stock rom from needrom.com? plz reply soon.i'm in dire state
thanx in advance
Click to expand...
Click to collapse
Sorry for the delay bro... I cant flash it via SP Flashtool with rom which I directly downloaded from the Infocus official website.
So I gave it to Service Center. As soon as I get my mobile back I will update you the method of Flashing...
Solved
tigerdhana1371102 said:
I accidently flashed wrong CWM recovery to my phone...
Now its went to boot loop....:crying::crying::crying::crying:
When I power on phone by pressing Vol Down + Power button it shows Fastboot mode in Mobile Screen at the Buttom edge...
But When I tried in Command Prompt with "fastboot devices" its dont show my device.... as well as "adb devices"
Some one please tell me How to flash my phone with orginal recovery.... Please....
Click to expand...
Click to collapse
Not a big deal dude.
Today it has been solved.:angel:
Go to the below link and Download link unable to post as a new user
then paste it in SD card for flashing.
Go to recovery model update from SD and flash it through.
Simple....... :good: have a nice day.
if u face any problem reply me.
---------- Post added at 12:16 PM ---------- Previous post was at 12:06 PM ----------
1
---------- Post added at 12:26 PM ---------- Previous post was at 12:16 PM ----------
2 waited for 4min
---------- Post added at 12:31 PM ---------- Previous post was at 12:26 PM ----------
i can paste link only after sending 10 reply
---------- Post added at 12:38 PM ---------- Previous post was at 12:31 PM ----------
why should i wait to help peoples
---------- Post added at 12:45 PM ---------- Previous post was at 12:38 PM ----------
5
---------- Post added at 01:20 PM ---------- Previous post was at 12:45 PM ----------
6
---------- Post added at 01:45 PM ---------- Previous post was at 01:20 PM ----------
---------- Post added at 01:58 PM ---------- Previous post was at 01:45 PM ----------
---------- Post added at 02:04 PM ---------- Previous post was at 01:58 PM ----------
:cyclops:
TigerDhana017 said:
Sorry for the delay bro... I cant flash it via SP Flashtool with rom which I directly downloaded from the Infocus official website.
So I gave it to Service Center. As soon as I get my mobile back I will update you the method of Flashing...
Click to expand...
Click to collapse
tiger dhana017 refer this part of ur comment
"rom which I directly downloaded from the Infocus official website"
where did u find the ROM from the official site?plz guide me or give me ur no mine is "08283821978"
thanx in advance
---------- Post added at 10:45 AM ---------- Previous post was at 10:35 AM ----------
funlover said:
Not a big deal dude.
Today it has been solved.:angel:
Go to the below link and Download link unable to post as a new user
then paste it in SD card for flashing.
Go to recovery model update from SD and flash it through.
Simple....... :good: have a nice day.
if u face any problem reply me.
---------- Post added at 12:16 PM ---------- Previous post was at 12:06 PM ----------
1
---------- Post added at 12:26 PM ---------- Previous post was at 12:16 PM ----------
2 waited for 4min
---------- Post added at 12:31 PM ---------- Previous post was at 12:26 PM ----------
i can paste link only after sending 10 reply
---------- Post added at 12:38 PM ---------- Previous post was at 12:31 PM ----------
why should i wait to help peoples
---------- Post added at 12:45 PM ---------- Previous post was at 12:38 PM ----------
5
---------- Post added at 01:20 PM ---------- Previous post was at 12:45 PM ----------
6
---------- Post added at 01:45 PM ---------- Previous post was at 01:20 PM ----------
---------- Post added at 01:58 PM ---------- Previous post was at 01:45 PM ----------
---------- Post added at 02:04 PM ---------- Previous post was at 01:58 PM ----------
:cyclops:
Click to expand...
Click to collapse
hi funlover where's the link bro plz just write it.i'm in big problem .
thanx in advance
hi all
thanx to all of u guys at xda i was able to get my infocus working again.here's what i did:-
1) downloaded stock ROM from needrom.com the one m mentioning here by the name @"LSO-2260-0-00WW-A02-update"
2) transfer it in the root of SD Card.
3)get into recovery mode,power hold alongwith volume increase and USB attached to PC.
4) The moing ment INFOCUS logo comes up leave the power buttton.
5)keep the volume increase pressed untill recovery screen pops up(you'll be able to make out it's recovery coz of the deceased android logo with exclamation mark in it's chest) or the screen changes color,if nothing comes written on the screen after recovery screen comes( ie the deceased android logo with exclamation mark in it's chest) plz press the power button
6)recovery menu will definitely pop up.
7) select install from SD card.
8) select the zip file from the drop down menu and install.
9) reboot then and wait it''l set up the way it sets up for the first time.
10) mind it it was for the INFOCUS M2 3G INDIA version
rgds n once again thanx.
bro beofore flashing the recovery u need to unlock OEM
fastboot -i 0x0489 oem unlock
Help me out
gauravinvouge said:
hi all
thanx to all of u guys at xda i was able to get my infocus working again.here's what i did:-
1) downloaded stock ROM from needrom.com the one m mentioning here by the name @"LSO-2260-0-00WW-A02-update"
2) transfer it in the root of SD Card.
3)get into recovery mode,power hold alongwith volume increase and USB attached to PC.
4) The moing ment INFOCUS logo comes up leave the power buttton.
5)keep the volume increase pressed untill recovery screen pops up(you'll be able to make out it's recovery coz of the deceased android logo with exclamation mark in it's chest) or the screen changes color,if nothing comes written on the screen after recovery screen comes( ie the deceased android logo with exclamation mark in it's chest) plz press the power button
6)recovery menu will definitely pop up.
7) select install from SD card.
8) select the zip file from the drop down menu and install.
9) reboot then and wait it''l set up the way it sets up for the first time.
10) mind it it was for the INFOCUS M2 3G INDIA version
rgds n once again thanx.
Click to expand...
Click to collapse
I did everything the same but my problem is i'm just unable to get the recovery mode. followed the all procedure. I choose the wrong CMW recovery Mobile Uncle tools an it makes boot stuck up. volume Up and powerbutton is not working for me i plugged the USG to pc it's restarting again again. Is there any way
Keeps rebooting, can't get recovery mode
How can you flash when the phone keeps rebooting ? it will not go into recovery mode.
The recovery is for Infocus M2 4g.. If flashed in 3g version, the phone will brick
hey i also got stuck in same prblm which tigerdhana has got into please expert members help me out
bump
stop spamming I m literlly dying to know solution
any guys plz help me my infocus m2 3g mobile used and my mobile is iroot to used rooted and i am download the update.zip file and my phone is install sucessfull after reboot on mobile is one problem is produced and my phone problem below attached image file plz help me.......................
any guys plz help me my infocus m2 3g mobile used and my mobile is iroot to used rooted and i am download the update.zip file and my phone is install sucessfull after reboot on mobile is one problem is produced and my phone problem below attached image file plz help me.......................
Here is the solution!
Same happens with me i flashed wrong recovery in infocus m2 and my device got bootloop and unable to boot in recovery. fortunately device is able to boot in fastboot mode.
here what i did next.
1. download stock firmware of Infocus m2 3g from here firmwarefile.com/infocus-m2-3g to your pc and extract it . open folder Firmware ,right click G10-020F-0-00WW-A02.zip ,select extract here.
2. This firmware zip has folder named as ServiceTool L1 V1.6.0 (IMEI). open it and run the setup.exe . after that run ServiceToolL1_V1.6.0.msi .
3. Now open folder SUTL3 v3.1.4 (Flash Tool) and run launcher.exe as administator, it will install sut flash tool.
4. Now open C:\Program Files (x86)\SUT L3 and find SoftwareUpdateTool.exe run it as admin(you can also run it from start> all programs>SUT L3). click next.
5. Now connect your phone to pc using usb cable. press volume down and power button at a same time(this will reboot your phone in fastboot mode ).you should see the fastboot mode text at bottom left.
6. Now select the sofware image by locating to Infocus_M2_3G_G10-020F-0-00WW-A02\ Firmware\ and select file G10-020F-0-00WW-A02.nb0 and then click open. in update option select normal download and click next. now you have to wait for about 10min or more. don't remove usb cable.
tool will download all files automatically to the phone and after downloading file it will reboot your phone automatically.
firstboot will take time .
if you follow these steps carefully then you will get your device back to the normal with all of your apps and data.
Note: This method will work even when your device is not detected by adb so go for it.
Hit thanks if this helps.
Use SUT Tool For Flashing Your Infocus M2
Download the firmware and the Software Update Tool (SUT) from the internet and flash the .nb0 or .ffu file through SUT tool... That's it it takes a 10-15 minutes and you're done.. :good:
Greetings,
Upon unboxing my OPO X and discovering it's limitations in regard to customization compared to Cyanogen (following this guide :
HTML:
http://oneplus.wonderhowto.com/how-to/install-cyanogen-os-12-your-oneplus-one-0161384/
),
I attempted to flash it using TRWP which I managed to install and start properly.
Either I messed something up with the install process or selected the wrong build for my specific phone (used YNG1TAS0YL-bacon-signed) but I was prompted to reboot my phone upon what I though was completion and ended up with no OS, hard bricked with QHSUSB BULK showing in device manager and totally blanked screen.
I then attempted to fix my own mess by following this guide :
HTML:
http://forum.xda-developers.com/oneplus-one/general/guide-unbrick-oneplus-one-t3013732
which suggested I uninstall the faulty driver and replace it with the one suggested.
By doing so, I then ended up with an unknown device and from there my real nightmare started.
I've about tried every single restore guide I could find narrowing my search to my specific model this time figuring it would prevent compatibility issues but still nothing is working.
The sum up what is currently going on with my phone, if I press Power + Volume up, I get "Qualcomm HS-USB QDLoader 9008" listed under the "Ports" section of the device manager. However I now get a result with QCOMDownloadTool (which fail to to anything but is listed in some guides). No access to either fastboot or ADB.
On the other end, Power + Volume down booting will list whatever drivers I've choosen among Google, Samsung, Universal ADB or OnePlus i've tried to install and will list the device as an "Android device". This give me access to fastboot, however ADB never ever detect any devices and attempting to boot the "twrp-2.8.7.0-onyx_f2fs_r5.img" will display "FAILED (remote:dtb not found)".
Also, I noticed that within driver detail under "hardware id's" I get :
USB\VID_18D1&PID_D00D&REV_0100
USB\VID_18D1&PID_D00D
but with the official "OnePlus_android_winusb.inf" it is not replicated for adb value with instead
%SingleBootLoaderInterface% = USB_Install, USB\VID_18D1&PID_D00D ;fastboot
%SingleBootLoaderInterface% = USB_Install, USB\VID_2A70&PID_D00D ;oem fastboot
%SingleAdbInterface% = USB_Install, USB\VID_2A70&PID_4EE7 ;adb
I'm all out of ideas, looking to try and fix it myself (with your help of course) before I go begging OnePlus customer support to save me.
Thanks in advance folks!
Try booting with your stock recovery. Img if you think it boots in fastboot
Sent from my ONE E1003 using Tapatalk
loveboy_lion said:
Try booting with your stock recovery. Img if you think it boots in fastboot
Sent from my ONE E1003 using Tapatalk
Click to expand...
Click to collapse
I think the most basic problem is that no matter what driver I attempted to use so far, end up not showing in ADB.
I don't know the relation between ADB and fastboot, but I probably don't have a fully functional driver.
I made I backup with TWRP before wiping, but I don't think "recovery.emmc.win" & "recovery.emmc.win.md5" will help me a whole lot from fastboot.
Any idea where to get an image file of the stock recovery and the exact commands sequence to be used afterward?
It might sound like I have an idea of what i'm doing because I've been trying to fix this mess for 2 days, but I really don't...
KrapnoV said:
I think the most basic problem is that no matter what driver I attempted to use so far, end up not showing in ADB.
I don't know the relation between ADB and fastboot, but I probably don't have a fully functional driver.
I made I backup with TWRP before wiping, but I don't think "recovery.emmc.win" & "recovery.emmc.win.md5" will help me a whole lot from fastboot.
Any idea where to get an image file of the stock recovery and the exact commands sequence to be used afterward?
It might sound like I have an idea of what i'm doing because I've been trying to fix this mess for 2 days, but I really don't...
Click to expand...
Click to collapse
if i am understanding you correctly then you tried to install oneplus one twrp and rom on oneplus x if you really did so no wonder device is bricked since either you erased all your partitions (which is bad since oneplus did not release files required to debrick hardbrick device) if you only messed up your recovery then you would need stock recovery.img of your e1005 since recovery.img of e1003 most probably wont work you could try though
regarding if you are not sure if your phone is connecting in fastboot or adb try uninstalling all drivers you have installed and install the below drivers and hope your phone is in fastboot mode
https://drive.google.com/open?id=0B48lBYmwzkD5WlFrU2lNb2d5WlE
---------- Post added at 05:40 AM ---------- Previous post was at 05:33 AM ----------
if you have fastboot chances to repair your phone are 99%
your device wont detect under adb
---------- Post added at 06:01 AM ---------- Previous post was at 05:40 AM ----------
you could also check this for help
https://forums.oneplus.net/threads/...om-recovery-root-take-efs-backup-more.401713/
Well, either I have rebooted before the installation was completed or I had the wrong kernel, but I no longer get any visual response from my phone beside vibrations when I power it on/off.
The drivers currently installed are the ones you provided, still there is nothing in ADB.
I can start a cmd fastboot and get a results from "fastboot devices".
See screen capture blow:
i.imgur(dot)com/KnFmTcf.jpg
i.imgur.(dot)com/4kat7Cv.jpg
I doesn't go any further than that, phone is still dead.
its good news for you
you are in fastboot mode
instead of installing twrp recovery install your stock recovery
it wont flash twrp since its getting dtb error and fastboot wont allow it to load since this version of twrp is for e1003 and yours is e1005
Where can I get an .img of the stock recovery?
I already did overwrite with TWRP so stock recovery is no longer present on the phone right?
I saw this file but I don't think I can use it:
drive.google(dot)com/file/d/0B0pr-ZA5b-1pM1prTmMwQmhOMXM/view?pli=1
you could try it hope it works chances of it working is 50%
fastboot flash recovery recovery.img
fastboot boot recovery.img (if this does not work and manualy try with power+volumedown)
---------- Post added at 06:40 AM ---------- Previous post was at 06:34 AM ----------
you are not alone with same problem
http://forum.xda-developers.com/oneplus-x/help/users-twrp-t3258756/post64071152#post64071152
---------- Post added at 06:49 AM ---------- Previous post was at 06:40 AM ----------
unless someone makes unified build of twrp for e1003 and e1005 you will face same problem if u try to flash twrp again
I do NOT have access to a "recovery.img" file on my phone.
What can I do next? Can these files I made a backup from be of any help currently?
i.imgur(dot)com/uEPBECy.jpg
yes the files are of help but only when u have twrp they cannot be used by fastboot
---------- Post added at 07:08 AM ---------- Previous post was at 07:05 AM ----------
try flashing this twrp recovery
http://ns336247.ip-91-121-110.eu/h2o64/onyx/twrp/
Bacon is for the oneplus one...
KrapnoV said:
Well, either I have rebooted before the installation was completed or I had the wrong kernel, but I no longer get any visual response from my phone beside vibrations when I power it on/off.
The drivers currently installed are the ones you provided, still there is nothing in ADB.
I can start a cmd fastboot and get a results from "fastboot devices".
See screen capture blow:
i.imgur(dot)com/KnFmTcf.jpg
i.imgur.(dot)com/4kat7Cv.jpg
I doesn't go any further than that, phone is still dead.
Click to expand...
Click to collapse
Do you realize you tried to install stuff for an entirely different phone? OnePlus One is not OnePlus X. There was the problem with your installs...
If you get into to fastboot I would try flashing something that is made for OnePlus X and see how it goes.
I would be very happy to flash a compatible rom this time, but while fastboot SEEM to work, i'm not sure it does.
Understand I've never done that before, but all the guide requires to be able to boot recovery to progress, and with that "FAILED remote dtb" error I'm getting I don't know how to go any further. The TWRP version i'm using "twrp-2.8.7.0-onyx_f2fs_r5.img" is supposed the be the right one for my phone.
I would also test stock recovery but I don't have an image file and so far no luck finding one.
KrapnoV said:
I would be very happy to flash a compatible rom this time, but while fastboot SEEM to work, i'm not sure it does.
Understand I've never done that before, but all the guide requires to be able to boot recovery to progress, and with that "FAILED remote dtb" error I'm getting I don't know how to go any further. The TWRP version i'm using "twrp-2.8.7.0-onyx_f2fs_r5.img" is supposed the be the right one for my phone.
I would also test stock recovery but I don't have an image file and so far no luck finding one.
Click to expand...
Click to collapse
Here is stock recovery image for E1005. https://drive.google.com/file/d/0B6zU7r3AtRjFb2tyQU11YTdLVEU/view?usp=sharing
Hi,
My phone OnePlus X E1003 was hard brick after install twrp.. now phone is dead..cannot access recovery and fastboot,screen blank and just vibrate.. when i plug in. it only detect qualcomm HS-USB driver.. but opx still dont have zip to repair the broken partition. anybody have ideal?pls help me.
Same problem here
apekgee said:
Hi,
My phone OnePlus X E1003 was hard brick after install twrp.. now phone is dead..cannot access recovery and fastboot,screen blank and just vibrate.. when i plug in. it only detect qualcomm HS-USB driver.. but opx still dont have zip to repair the broken partition. anybody have ideal?pls help me.
Click to expand...
Click to collapse
Same here, black screen only vibrates on holding power button for 10 seconds :crying:
apekgee said:
Hi,
My phone OnePlus X E1003 was hard brick after install twrp.. now phone is dead..cannot access recovery and fastboot,screen blank and just vibrate.. when i plug in. it only detect qualcomm HS-USB driver.. but opx still dont have zip to repair the broken partition. anybody have ideal?pls help me.
Click to expand...
Click to collapse
What did you do besides trying to install twrp? It would be difficult to brick by just flahshing recovery unless it was the wrong one.
Sent from my ONE E1005 using Tapatalk
If you can get it in bulk mode then you should probably try this http://forum.xda-developers.com/one...stboot-adb-t2835696/post55024864#post55024864
Ok...easy peasy....it happened to me too...Just open a ticket for a remote session with oneplus.....
They do mostly everything in about 45 minutes.
I tried everything too, nothing worked. Don't stress yourself out...They were good about it.
joey24z1 said:
Ok...easy peasy....it happened to me too...Just open a ticket for a remote session with oneplus.....
They do mostly everything in about 45 minutes.
I tried everything too, nothing worked. Don't stress yourself out...They were good about it.
Click to expand...
Click to collapse
pls help me how u manage to contact technical support?
Recently I installed a room on my Xperia Z2 (Ressurection Remix). It worked fine until I lost the password of my lock screen, and to solve I tried to access my recovery to give a wipe, however the room did not give access to my recovery (TWRP 3.0.2.0), to solve I tried to install my firmware Original Xperia Z2, by the flashtool, I installed all the drivers of my device and when I went to try to enter the flashmode mode the cell phone did not enter (lit a green LED and then red and turned off the device) the device goes into fastboot without problems, So after that I made a bigger asshole, by flashtool I put the device in fastboot mode and installed a TWRP kernel to see if it worked, it did not work. Now I have my device turned off and it does not turn on and only goes into fastboot. Could any kind soul help to fix my problem, or was it?
Same here op if you find a solution please tell me its been 8 hours till now and still cant find anything
all the buttons are working fine but cant power on the device or even get into flashmode.
as you said the green led flashes for a sec then reboot on and on
hope someone can solve this problem
Download an FTF from Xperia Firm make a bundle with that(everything is inside it) then flash it. When the windows pops up to connect hold volume - and connect it. It will be fine. Happened to me too. In flashtool flash screen allow it to wipe everything.
Laskr1999 said:
Download an FTF from Xperia Firm make a bundle with that(everything is inside it) then flash it. When the windows pops up to connect hold volume - and connect it. It will be fine. Happened to me too. In flashtool flash screen allow it to wipe everything.
Click to expand...
Click to collapse
its no use just tried this and didnt work for me , as i said earlier i cant access flash mode .the device it self is not recognizing the volume - key even if i spam it when it reach the pop-up or before that. and the key work just fine ,
the only thing that we can do now is to flash something via fastboot option but how ? i have no idea
Connect phone in fastboot mode and open a adb command window then enter in the commands to reboot into recovery or bootloader etc
Sent from my LG-H960 using Tapatalk
---------- Post added at 09:55 PM ---------- Previous post was at 09:52 PM ----------
https://www.guidebeats.com/2016/07/10/adb-fastboot-commands-ultimate-list/
Sent from my LG-H960 using Tapatalk
thanx for the fast answer
im not that expert using command so if you can give me a detailed command and what to do after every thing would be awesome i flashed the kernal and the recovery but didnt know how to flash the system using command line
o0oArchangelo0o said:
Connect phone in fastboot mode and open a adb command window then enter in the commands to reboot into recovery or bootloader etc
Sent from my LG-H960 using Tapatalk
---------- Post added at 09:55 PM ---------- Previous post was at 09:52 PM ----------
https://www.guidebeats.com/2016/07/10/adb-fastboot-commands-ultimate-list/
Sent from my LG-H960 using Tapatalk
Click to expand...
Click to collapse
i just tried this and everything was fine but when am trying to enter recovery mood i cant and the device is not working even that everything flashed correctly
guess that my device is missing the bootloader and need to be flashed to let me enter the bootloader but couldnt find any bootloader.img
will it work if i flashed the recovery in bootloader partition ?
Im jus checking but did you unlock the bootloader yourself or?
Alpha-2-omega said:
Im jus checking but did you unlock the bootloader yourself or?
Click to expand...
Click to collapse
yes i did unlock the bootloader a year ago but not sure if it still unlocked or get locked again no idea
and i dont know how to chick if its locked or not using fastboot tool cuz i cant access flashmode on this device which is something flashtool ask for to give you the bootloader statues
if you have any idea that would be great to tell me to try it :laugh:
---------- Post added at 01:39 AM ---------- Previous post was at 12:55 AM ----------
http://imgur.com/FTNXf5L didnt know how to upload the pic here see it in the link
this is what happend when i tried to chick bootloader statues and nothing shows after 5 min of waiting
so guess there is no bootloader if you have any idea about it
It looks like you have bricked your phone somewhere along the line of installing cm with remix rom, maybe you didnt flash correct kernel when changing idk but im out of ideas here
Alpha-2-omega said:
It looks like you have bricked your phone somewhere along the line of installing cm with remix rom, maybe you didnt flash correct kernel when changing idk but im out of ideas here
Click to expand...
Click to collapse
i went to some expert to fix it they told me that the internal memory need to be redistributed or if it didnt it had to be changed by changing the motherboard and this will cost about 130-150 $
so ya thats the problem now
if anyone know how to re program the internal memory that would be awesome
ElectricB said:
i went to some expert to fix it they told me that the internal memory need to be redistributed or if it didnt it had to be changed by changing the motherboard and this will cost about 130-150 $
so ya thats the problem now
if anyone know how to re program the internal memory that would be awesome
Click to expand...
Click to collapse
If you can access to fastboot then:
1- Flash the Boot.img from Lineage rom via fastboot using this command: fastboot flash boot boot.img
"boot.img" I assume you put the boot.img in the same dir with fastboot.
2- Flash TWRP Recovery via fastboot using this command: fastboot flash recovery recovery.img
I assume you put the recovery.img in the same dir with fastboot.
3- Boot into Recovery by using VOLUME UP when Sony logo comes up with pink notification light.
Link to recovery.img [url]https://mega.nz/#!iBQkgabb!B3G6dmlEMu-2xRV4w8Fl4xzRYlXSDgTeXhRtgevuT9A
And check the driver of fastboot and flashmod if it installed correctly and always use flashtool v0.9.18.6 only for Z2
darknessmc said:
If you can access to fastboot then:
1- Flash the Boot.img from Lineage rom via fastboot using this command: fastboot flash boot boot.img
"boot.img" I assume you put the boot.img in the same dir with fastboot.
2- Flash TWRP Recovery via fastboot using this command: fastboot flash recovery recovery.img
I assume you put the recovery.img in the same dir with fastboot.
3- Boot into Recovery by using VOLUME UP when Sony logo comes up with pink notification light.
Link to recovery.img [url]https://mega.nz/#!iBQkgabb!B3G6dmlEMu-2xRV4w8Fl4xzRYlXSDgTeXhRtgevuT9A
And check the driver of fastboot and flashmod if it installed correctly and always use flashtool v0.9.18.6 only for Z2
Click to expand...
Click to collapse
i was sure this wont work but i tried it to confirm
flashed them as you said but i cant power up the device ,the power button is working fine but cant power up
plugged the device directly into power source and tried to inter recovery mode as you said but nothing
the screen flashes with sony logo then reboot as fast as that
i was pressing volume button like a retarded maybe i will get into recovery mode but nothing happen
guess the only thing to do now is to change the motherboard since i have one from another device
Kawaiiluiz said:
Recently I installed a room on my Xperia Z2 (Ressurection Remix). It worked fine until I lost the password of my lock screen, and to solve I tried to access my recovery to give a wipe, however the room did not give access to my recovery (TWRP 3.0.2.0), to solve I tried to install my firmware Original Xperia Z2, by the flashtool, I installed all the drivers of my device and when I went to try to enter the flashmode mode the cell phone did not enter (lit a green LED and then red and turned off the device) the device goes into fastboot without problems, So after that I made a bigger asshole, by flashtool I put the device in fastboot mode and installed a TWRP kernel to see if it worked, it did not work. Now I have my device turned off and it does not turn on and only goes into fastboot. Could any kind soul help to fix my problem, or was it?
Click to expand...
Click to collapse
found the solution op the problem was that the battery is empty go charge it somewhere then flash the system you need
my device works like a charm now have fun :good:
ElectricB said:
found the solution op the problem was that the battery is empty go charge it somewhere then flash the system you need
my device works like a charm now have fun :good:
Click to expand...
Click to collapse
What?!! You supposed to check it before doing anyhing.