Hi guys,
I have serious problems with my Amazfit Pace A1612, the bootloader is unlocked, after PACEfied, all functions not working: GPS, Compass, Heart Rate, Pedometer and Slep Monitor.
I already flash the version 1.3.0n and same problem, after flash the system found official update i accept, the watch install after reboot and stuck in updating screen (brick the watch and i need make very difficult manual fastboot mode) i reinstall 1.3.0n the reboot and working partialy (the GPS, Compass, HR, Pedometer, Slep Monitor not work and battery drain very fast).
I already install CN version v0.9.50 and working similary the US v1.3.0n (no GPS, Compass, HR, Pedometer, Slep Monitor and Battery drain very fast) the system found lastest CN update and situation same the US 1.3.0n(brick the watch in stuck Updating screen).
I need a Help!!!
Thanks my dears.
Related
I have an Amazfit Bip clock and it has blocked in "Activity" page.
The touch screen does not respond, the physical side button either, the Mi Fit fails to connect, ...
The clock continuously displays that "Activity" menu screen and you can not interact with it.
How can I reset it or what should I do to use the watch?
I use Mi Fit 3.0.5, FW-0.9.14
Thanks
montarelonf said:
I have an Amazfit Bip clock and it has blocked in "Activity" page.
The touch screen does not respond, the physical side button either, the Mi Fit fails to connect, ...
The clock continuously displays that "Activity" menu screen and you can not interact with it.
How can I reset it or what should I do to use the watch?
I use Mi Fit 3.0.5, FW-0.9.14
Thanks
Click to expand...
Click to collapse
Yes, it happens when BIP trying updating A-GPS data. Run MiFit, keep watch close phone and let him update. Sometimes is failed, but close MiFit, clear memory and try again until success.
Thanks a lot.
In fact, it must be something related to what you say, becasuse as soon as the clock was recovered and connected again to the Mi Fit, it began to update the A-GPS.
What I do not know is if the solution you proposed works, because while it was blocked, the Mi Fit did not recognize it (it always put Connecting ...), it did not connect and I mismatched it and then I could not find it to link it again. That is, there was no bluetooth connection between My Fit and Clock, so I do not know how I could have updated the A-GPS clock trough the Mi Fit
Fortunately, the clock went off and when I put it to charge it started well and it works.
Hi there,
since today i have got the same problem. Sadly the battery is charged 100% so waiting for discharge may take some time. Does somebody know how to reset or force reboot or force discharge the watch?
Thanks in advance!
Amazfit bip problem
Hi, i got exactly the same problem with you..
After i switched my smartphone (from huawei P9 to LG V20) My amazfit Bip suddenly updating A GPS and after that, the touch display is hardly responding, then when i long press the button, it start to displays workout session that cannot be stopped or interrupted in the meantime, Mi Fit can not sync/interract during workout session).
After spent several frustating days, finally i conclude that the main issue is the firmware.
So here is what i did :
- Let the Amazfit watch battery drain (since the activity/workout session can not be stopped, it will drain faster than ussual).
- Recharge the watch until more than 10% and re-connect it to Mi Fit app. (Don't charge it too long, because when something goes wrong you will have to take time to drain the battery again).
- Download NOTIFY & FITNESS FOR AMAZFIT" app from google playstore and connect your Amazfit with the app.
- When the Amazfit Bip paired to Notify & Fitness For Amazfit,
unpaired the watch from the Mi Fit App, then uninstall Mi Fit from your phone.
- Now you have only 'Notify & Fitness for Amazfit' app connected to your amazfit bip.
.- Go to setting section in the app, scroll down and you will find firmware update section, then update the amazfit firmware (you will find some option : english/spain/italian etc., i've choosen english version)
- There imare 3 items that you have to sequintly update one by one : firmware, recources and gps (i failed to update the gps, but all i know, it doesn't matter anyway...)
- After the update finished (sometimes it failed, but i repeat it on and on untill it's succeed), my amazfit starts to work proper and not displaying work out session anymore.
Notify & Fitness for Amazfit is my saviour!
It works better than the official Mi Fit app.
Blocked after Workout
I also had a blocked Amazfit Bip:
On my first workout (a 3 hour bicyle ride), I wanted to stop it. Unfortunately the watch always restarted the workout again.
First I thought that I had double tapped the screen after pressing the Ok (to finish) button. But I tried this for at least 30 times. It always restartet the workout.
I still got a connection from the Mi Fit App, but it told me that the watch is within a workout.
I disconnected / reconnected the MiFit App several times and somehow I was able to quit the Workout.
I immediately switched off the watch, restarted and everything was fine again. No new firmware flashing was required.
I only have it since two days.
[Firmware 0.1.0.26]
To all Stratos users. Do you having this problem?
Why is that the real time display sport Data keep changing during lock mode?
I want to see the Lap Time, Lap Pace and Lap HR, but it only temporary and will change back to default value as soon as the screen was lock. So, I am wondering, what is the purpose of having this when it is clearly can not being display throught out the workout session. Funny isn't it?
No issues here using firmware 2.3.6.0 and Amazfit 2.6.3 from AppStore (tested with Treadmill). Choose what data you want to see and the order in Amazfit and it is displayed on watch after syncing, even when screen is locked. If you have problems, I suggest that you reset watch data: upair and pair again but do not restore old data to watch. If you still have problems, do the same but reinstall Amazfit after unpairing watch.
It's true. the problem has been resolved. I just have to reboot the watch, and the active screen will display the lap HR, Pace or cadence just the way i wanted.
Good evening to you all,
I´m facing an issue with my watch (or app i don´t know).
When i measure HR in manual mode, the value is not sincronized with the app (version 3.6.2), but when is set in continuous mode/ or doing sports everithing works fine. This has started after the watch came from support. the HR protector got sepparated from watch.
PS: If i downgrade the app to version 2.7.0 everything gets back to work...
Rom version: 2.3.11.1
Thanks in advance
Got dame issue with stratos 3. App Sync pb i think
Hi,
My Amazfit GTR 47mm is fully updated with latest app ver 3.6.2 and watch firmware is 1.3.5.37. this version supports Always on display with Smart feature. In smart feature the AOD should turn off automatically after a while when watch is removed or when sleeping, but this is not happening. Can any one help how to make this work.
skmdmasud said:
Hi,
My Amazfit GTR 47mm is fully updated with latest app ver 3.6.2 and watch firmware is 1.3.5.37. this version supports Always on display with Smart feature. In smart feature the AOD should turn off automatically after a while when watch is removed or when sleeping, but this is not happening. Can any one help how to make this work.
Click to expand...
Click to collapse
Having exactly the same issue. AOD doesnt turn off when i am sleeping or the watch is of my wrist.
Probably worth reporting the issue via the Amazfit app.
maximum71 said:
Having exactly the same issue. AOD doesnt turn off when i am sleeping or the watch is of my wrist.
Click to expand...
Click to collapse
I figured it out. If automatic heart rate detection is turned on then the watch never goes to sleep. Try turn off heart rate detection after that it will go to sleep as expected. Hope this helps.
skmdmasud said:
I figured it out. If automatic heart rate detection is turned on then the watch never goes to sleep. Try turn off heart rate detection after that it will go to sleep as expected. Hope this helps.
Click to expand...
Click to collapse
I tried to disable the continuous heart rate monitor, but the issue remains.
I described the issue through amazfit app, and sent it to them, hope to hear soon from them.
So, to all who is still watching this thread, i have an official update from amazfit gtr support.
Bottom line:
global version GTR does not equip with capacitive sensor, so it does not support off-wrist detect function.
I went through a few iterations with their support on my ticket, including sending them logs and what not.
They ended up sending me this message [1].
Which i dont entirely agree with, because they didnt mention why the AOD doesnt turn off when you fall asleep. I mentioned this again in my reply. But i doubt they will come up with any other reasonable explanation...
[1]:
Sorry that we made a mistake that we describe wrongly about the Smart Always-on function. Actually, global version GTR does not equip with capacitive sensor, so it does not support off-wrist detect function. When the watch detects you falling asleep, the Always-on function will be turned off. But putting it on the desk does not meet the conditions of "falling asleep", so the Always-on function will not be turned off.
We will modify the description about the Smart Always-on function in future firmware update. Sorry for all the troubles we caused.
Thanks for sharing this information. I never thought that the Chinese and global had hardware difference.
Apart from this the AOD is very weak in sunlight, my friend has a Huawei gt2 watch his AOD is very visible in sunlight.
maximum71 said:
So, to all who is still watching this thread, i have an official update from amazfit gtr support.
Bottom line:
global version GTR does not equip with capacitive sensor, so it does not support off-wrist detect function.
I went through a few iterations with their support on my ticket, including sending them logs and what not.
They ended up sending me this message [1].
Which i dont entirely agree with, because they didnt mention why the AOD doesnt turn off when you fall asleep. I mentioned this again in my reply. But i doubt they will come up with any other reasonable explanation...
[1]:
Sorry that we made a mistake that we describe wrongly about the Smart Always-on function. Actually, global version GTR does not equip with capacitive sensor, so it does not support off-wrist detect function. When the watch detects you falling asleep, the Always-on function will be turned off. But putting it on the desk does not meet the conditions of "falling asleep", so the Always-on function will not be turned off.
We will modify the description about the Smart Always-on function in future firmware update. Sorry for all the troubles we caused.
Click to expand...
Click to collapse
The Zepp app is very poor at tracking deep sleep. Anyone with the same problem?
Notify & Fitness for GTS is tracking fine.
Two months ago,it tracked sleep normally, but now it doesn't.
Any help? I also reinstalled
See attached images
Yes, I also have the same problem with deep sleep tracking! I made a complete reset of the GTS but it doesn't work. The problem is still the same! I also noticed that since the Zepp update the heart rate is not so accurate as normal and also PAI isn't working. Very disappointing, the GTS was great but now I am thinking to switch to another brand.