Please help me
I FLASHED TWRP ON MY MATE 10.AND NOW DEVICE STUCK IN PAGE (YOUR DEVICE IS BOOTING NOW).I CAN NOT GO TO FASTBOOT BY(VOLUME DOWN AND POWER)NO RECOVERY NO FASTBOOT.AND PC NOT RECOGNISE MY PHONE.WHAT SHOULD I DO?IS THIS SOFTWARE PROBLEM OR HARDWARE(CHANGE MAINBOARD).WHEN I PRESS VOLUME DOWN AND POWER PHONE RESTARTED AND I SEE LOW VOLUME BATTERY ICON AND RED LED VOLUME BLINKING.AFTER 2 OR 3 MIN HUAWEI LOGO COME AND STUCK AT (YOUR DEVICE IS BOOTING NOW) AND RED LED BLINKING .I PUT IS CHARGER AND PHONE STAY BLINKING AND GET WARM BUT NOT HELP ME
Try to flash stock rom again.
And don't write in caps.
Related
When i go to Bootloader (Hold Physical Power + Vol Up) this will show up an Empty Battery Logo
When i go to Recovery (Hold Physical Power + Vol Down) NOTHING will show up on the screen not even a vibrate from the phone
When i just turn on ASUS Zenfone 5 it will show the White USB Logo then it will Bootloop
When i plug ASUS Zenfone 5 to Wall Power Outlet for charging it LED Indicator will not light up
When you turn on ASUS Zenfone 5 while its plugged to the PC the USB Logo is stucked on the screen and it toggles from White to Red Colored Buffer by itself sometimes
When i plug it to my PC while its powered on "Cloverview" will be recognized by my PC's devmgmt.msc but phone screen will shut on and off by itself and "Cloverview" from devmgmt.msc will appear and dissapear the same time that the screen goes on and off
When i plug it to my PC while having an Empty Battery Logo (Bootloader) "Cloverview" will not show up from devmgmt.msc
I need help Badly Please help me :crying: :crying: :crying: :crying: :crying:
jinconstantine said:
When i go to Bootloader (Hold Physical Power + Vol Up) this will show up an Empty Battery Logo
When i go to Recovery (Hold Physical Power + Vol Down) NOTHING will show up on the screen not even a vibrate from the phone
When i just turn on ASUS Zenfone 5 it will show the White USB Logo then it will Bootloop
When i plug ASUS Zenfone 5 to Wall Power Outlet for charging it LED Indicator will not light up
When you turn on ASUS Zenfone 5 while its plugged to the PC the USB Logo is stucked on the screen and it toggles from White to Red Colored Buffer by itself sometimes
When i plug it to my PC while its powered on "Cloverview" will be recognized by my PC's devmgmt.msc but phone screen will shut on and off by itself and "Cloverview" from devmgmt.msc will appear and dissapear the same time that the screen goes on and off
When i plug it to my PC while having an Empty Battery Logo (Bootloader) "Cloverview" will not show up from devmgmt.msc
I need help Badly Please help me :crying: :crying: :crying: :crying: :crying:
Click to expand...
Click to collapse
Sounds like you've bricked it good. RMA it and ASUS should take care of it.
same problem here.
it happens when i tried to downgrade firmware using this guide.
http://www.asus-zenfone.com/2014/09/how-to-downgrade-from-442-kitkat-to-43-Jellybean-Zenfone.html
but i successfully downgraded it. and my phone can boot on home screen only when connected to a charger but it doesn't charging at all..
my only problem is when i try to press power and volume up. an empty battery appears with a question mark at the middle.
and my phone doesn't charge anymore.
did you try to flash stock firmare using adb?
hi there! just want to ask if zenfone 5 wont turn on, not charging, and it is not detected by pc with necessary drivers for the phone installed mean "unrepairable"?
Hi
My Z Ultra stays on android logo. Reset button don't work and power too. I tried reboot from adb (because its connecting normaly) and now stuck on black screen with red led. It's not charging, i left for like 2 hours and its only reboots to baterry symbol and reboot again. Can't get into flashmode and fastboot, red led appears and nothing else. What can i do?
Did u try power button + vol up for 10 sec? Then when he vibrate put charger in and go to bootloader for fastboot kernel or whatever you want
I just tried and it's don't vibrate
I think if I remember correctly red LED and no response is a motherboard/flex cable issue (could be wrong) this happened to me when I flashed the wrong software, I was still under return policy.
But yeah if flashtool isn't picking it up, you're SOL.
Hello there,
first sorry for my bad English, if you cannot understand me please ask
My friend asked me to (factory) reset his M4 Aqua because it won't start anymore (boot loop).
I used the flashtool and flashed the 26.3.A.1.33 (Customized DE for E2303) with standard settings (without flashing the userdata)
It worked without problems and the phone started until it said, "Android is starting...". Some seconds later the phone rebooted and stuck at the Sony logo with a glowing red LED.
After a half an hour I put it off by pressing the power and volume up button until it vibrated three times.
I tried to put it back into flash mode but nothing happened (LED doesn't blink, PC don't recognises the phone - just nothing). Same for the bootloader.
I've read something about holding the volume buttons and the power buttons for 30 seconds to reset the phone, but it doesn't help. (Flash mode and bootloader still haven't worked)
I pressed the off button near to the sd slot for ~15 seconds and after that, I was able to put the phone into the flash mode, but the PC still doesn't recognize the phone.
After removing the USB-cable the phone doesn't exit from the flash mode, so I press the off button again until the green LED went off.
I've noticed that the bootloader works, but the bootloader is locked and I was not able to unlock it.
So by now:
The phone stuck at the Sony logo with a bright shining red LED,
flash mode doesn't work (green LED lights up, but the PC doesn't recognize it),
the bootloader is locked (but works).
Please tell me, if you know how to revive the phone.
thank you in advance
You will have to flash the firmware again with flashtool maybe try and download another ftf file from a different source and try again.
Remember to only connect your phone in fastboot mode when flashtool prompt's you and all should be good.
Guys my Mi Pad 1 was running on Remix Rom based on shield blobs. Suddenly it hanged up upon reboot it only went into FASTBOOT, could never boot into bootloader. I did not have the time to fix it right away, now the situation is it does not boot up even to the fastboot screen. Only when connected to power outlet, first red led notifications blink then the Mi Logo comes up and then it goes into fastboot, but in the fastboot mode when connected to PC it does now show up.
Looking for some advice and help on how to fix this situation.
Get new USB cord and leave on charge hold power button down like 20 30 seconds plug it in while tapping power ..
Try holding volume down when off and plung in pc ..
Hello! I changed my screen ystd, and in the process somehow bricked my phone (?!)
Now my poco f1 won't turn on.. so i tried all the hard resets (vol+power) and nothing. When I charge it up with power brick or my pc, it boots into charging mode but nothing else. When i try booting it up it normally or fast boot or recovery again nothing happens, only charging logo. The charging logo stays on for about 3 second and then disappears. When I unplug the phone, it reappears for about a second and disappears;
I am on pixel experience (android 11 latest) . Also when i connect it to the pc the same issue happens (charging screen) and it shows in device manager as portable devices E:/ . It does not show in adb devices.
I found a thread with the same issue : https://forum.xda-developers.com/t/poco-f1-stuck-on-charging-logo.4031591/ , and someone commented that "Bootloader and recovery partition might have corrupted." What can I do about this? Is EDL flash the only option left? THanks!
in case anyone see this in the future, i was an idiot, while removing volume button and power button ribbon, i made a tear in it, the power button was simply unusable.
to boot it up, i pressed power up while connected to power source which launched into twrp