Hi everyone,
After charging for a while as always my Note 4 (MTK) powered off and, at boot, started to show the classic Mi logo "fading" in a vertical gray stripes screen, so I can't actually use the phone.
It has locked bootloader and it has no recovery.
Fastboot is working (and the screens works normally in it), so I tried to flash something with SP hoping this is only a strange sw issue.
The problem is: Windows shows my device as an Unrecognized USB Controller, even though I got all drivers (except for MTP, which won't install) installed on my pc, so SP tool won't start downloading.
Any solution?
Thanks in advance.
Related
Hi Masters,
I just like to inquire if I can still unbrick my clone Note phone. It has same spec as the HDC 5.7 Lord N9588 same box with NeoI brand. The main reason I flashed the ROM is because the accelerometer and GPS is not working so I found this ROM in needrom.com under HDC Lord N9588. as instruction says do not change anything in the setting (includes preloader). It successfully flashed the ROM but after reboot, the display is messed up and showing different color vertical lines. same as in the recovery. I believe that the phone still boots up, only the display messd up as I still can hear a sound every time I press the button and the screen and can hear volume sound when pressed. I still have the original ROM but the problem is it does not connect to SP flash. Last time when I connect to SP flash I can see MTK PReload VCOM USB when connected, now I can only see Preloader VCOM USB and gives errorS_COM PORT OPEN FAIL ERROR (1013) .already tried reinstall usb drivers.I can still access the phone trough adb shell but could not flash using fastboot at it says device not detected.
Thanks for any advice in advance.
Regards,
Ferdie
Hello,
During the past days I've been trying to flash my C7 with no success. When pressing power button, it turns on and displays the Alcatel logo but stays there, it does not load the OS.
I have tried to use SPtools to flash it, I have the mtk drivers installed in my PC. When I plug the switched-off phone to the computer it turns on and couple seconds after my PC detects it (I can see the preloader mtk loaded on the device manager); however, one second right after it is detected, it is disconnected as it keeps booting to show the logo and stay there. Obviously, if the phone is not detected I cannot use SPtools to flash it.
Any suggestion will be highly appreciated.
PS: I have also tried to connect to it with adb, and dump a ROM using sideload with no sucess, the PC recognizes it from the recovery but after copying the image nothing new happens on reboot.
Some wanker had posted wrong images for boot and recovery for S6000L. And since I'm a moron, i didn't take the files apart to check them.
Installing them bricked my tablet. So essentially I have no boot or recovery images on the device and was wondering if there's any way to revive it.
Tablet freezes if i start it in normal, fastboot or recovery modes, so that's out of the picture.
However, i think that "meta mode" still works (if indication of it working is displaying lenovo logo and having "meta mode" written on the bottom of the screen)
It's getting detected on "mediatek preloader usb vcom port" for a couple of seconds when connected to the PC, which means that i might be able to use adb to push a backup into the tablet (?)
Been scouring the internet for a while with no results. Is there, by any chance, anyone who can help me out?
Hello, as a lot of us I tried to install new rom and my device was completely bricked, no edl, no detection, no fastboot, so I open device, remove cover and made conenction between pins as I found on internet, it was very similliar to reset bios on pc motherboard.. device was detected, I have installed ROM for my device, I tried developer and stable too, but still the same. My screen is still blank, in Windows I see my device as Redmi 3S, I can switch my device to fastmode, but still wit black screen. Have you any idea what is wrong?
I think, that problem is with screen, not with software. I have disconnected and connect back battery for few times, but no contact with screen.
Do you know, where is connector for screen?
Regard,
Jiri
Hello Guys,
I would like to flash a Redmi Note 3 pro with twrp.
The problem is it is not recognized by PC. It's not even showing anything in device Manager.
I installed usb drivers from Xiaomi, I booted to Fastboot Mode and connected the Phone to the PC. Nothing is happening. No device ist showing in device Manager.
I tried 3 different USB cables and also to connect it to a notebook instead using my PC. No Chance.
Then I tried to connect a Redmi Note 4X in Fastboot mode and the same happened. IT IS Not recognized and the device manager don't show a new device.
Both phones are officialy unlocked.
Anyone who faced the same problem and can help
Joe886 said:
Hello Guys,
I would like to flash a Redmi Note 3 pro with twrp. The problem is it is not recognized by PC. It's not even showing anything in device Manager. I installed usb drivers from Xiaomi, I booted to Fastboot Mode and connected the Phone to the PC. Nothing is happening. No device ist showing in device Manager. I tried 3 different USB cables and also to connect it to a notebook instead using my PC. No Chance. Then I tried to connect a Redmi Note 4X in Fastboot mode and the same happened. IT IS Not recognized and the device manager don't show a new device. Both phones are officialy unlocked. Anyone who faced the same problem and can help
Click to expand...
Click to collapse
Hi, so you have tried 2 PCs, 2 phones and 3 cables. I think you missed it in the Device Manager. Please connect your RN3P phone in fastboot mode and run http://www.uwe-sieber.de/usbtreeview_e.html then do File/Save full report, and post it here. Alternatively, run any live Linux and post lsusb output.
Thank you for your reply.
As it seems I can´t post links because i`m new and when I try to post the report here it says I can`t because it has more than 30000 caracters
But as I said it won´t be recognized. Both of them won`t.
When I connect them in working mode I can´t even access the data like pictures etc.
One of the 3 usb-cables were originaly packaged as I at first suspected the usb cables were faulty.
But now a friend of mine come by and I tested to connect his Redmi note 4x and it is working. The only difference is that he has miui 8 and I have miui 9 from xiaomi.eu.
So I am out of ideas now. The only I can imagine is that both usb ports on the smartphone are ****ed and therfore it won´t connect properly.
Charging is no problem by the way
Bro you have to setup adb drivers perfectly a single error in setting up leads error but no worry it would not harm your device....
So first of all setup adb driver from the given link it will show you how to setup adb driver
Then go your processor of setting up twrp.
If you need any help on setting up twrp just reply on it....