DIY Clear back cover - Moto 360 2015

Hey, how many of these little guys stay up and working?
Today I've opened my carp (42 mm edition) to look at the ports, just to look at the possibility of connecting it via USB for modding, root, flashing ROMs, etc. (so bad there's almost no scene on this device series ) when suddenly a crazy idea just crossed my mind: Why don't try to expose the guts of this old, used (and abused) watch, like those expensive skeleton watches?
So I've inspected carefully the back glass cover and noticed that there was a gluey sticker between the glass and the device itself. After removing the sticker, the glass is exposed and ready for some abuse.
The sticker:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
The next step was to find a way to remove the paint without damaging the glass itself, so I've taken a knife and tried, with success, to gently scratch the paint. TBH, I'm very surprised of the scratching resistance of that glass piece, because you can give it some serious abuse (like fast, hard scratching) without leaving marks on it, so if you try to do this mod you don't need to worry too much about damaging it, just don't apply too much strength and pressure to avoid deep scratches or breaking the glass (if you hold it on your hand or on top of a soft, non-hard surface).
After about 30-40 minutes of scratching paint, I've cleaned the glass with my breath and a cloth, applied some thin double-side tape (aka. smartphone tape, very useful when repairing stuff like that) to fix the glass on place and did the same for the outer plastic ring. Now, here's the result:
As you can see below, the text remains intact, I suppose that is printed deeper inside the glass or something:
Looks pretty nice if you like the look of the bare naked electronics. Aside from that, I feel sorry for that disturbing off-center white ring (I guess it has moved a bit when I've put the glass back on the watch) and that wire that separated from the charging coil when I oppened the watch. Maybe I'll fix it one day. Cheers.
EDIT: I've done a WatchMaker watchface matching the skeleton style of my back cover. Here's a picture, I've attached the .watch file for anyone to use it:

Very nice mod! Will be replacing the battery on my 42mm soon and will have to give this a go.

Related

Mod for Speck Candyshell for better GRIP

For anyone who owns a Speck Candyshell (like me) I'm sure they know that the case can become slippery when your hands are sweaty or oily so I thought of an old trick that I have used for other things: Plasti Dip!
A couple of coats and 'voila', excellent grip and it's much more scratch resistant. Even the "Speck" logo is still visible (see pics). Just make sure you tape off the openings and anything you don't want sprayed.
Here is a link for Plasti Dip from Home Depot:
http://bit.ly/I2VCHc
You can also find different colors online.
And here are some pics (the photos doesn't do it justice because it actually looks much better then these images):
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Looks good. Did you rough the case up before spraying? got a picture of the front? I wonder how long it will last before it peels...
over2land said:
Looks good. Did you rough the case up before spraying? got a picture of the front? I wonder how long it will last before it peels...
Click to expand...
Click to collapse
^ This, I'll be watching here. I have a Speck which, besides being nearly impossible to remove the phone from, I otherwise liked pretty well.
Just cleaned it with warm water and soap then dried. There really wasn't much to show from the front which is why I didn't take any pics. I did spray front and back though. I taped off all the openings from the inside of the case to spray the back and then I cut out a piece of paper the size of the phone and placed it in the case to spray the front.
I was in a hurry yesterday after spraying it so I ripped all the tape and paper off quickly which did leave some rough edges around the openings and only one small spot did it peel back. I would recommend letting sit for the full four hours it's supposed to dry and then use an X-acto knife to cut around the edges for smooth lines. I plan on throwing another coat on when I get my new SD card and I have a reason to remove the case. I will also update the post after some use to let everyone know if it holds up. (Some people use Plasti Dip on external parts of their vehicles and it holds up well against the elements so I think it will do fine)
Also, just an FYI, I cut out the rubber pieces for the power button and volume rocker because I kept accidentally pressing them when holding the phone. I then sanded the areas around the openings to make it easier to reach with my fingers/thumbs. I thought I'd throw that out there in case anyone noticed they looked different.
over2land said:
Looks good. Did you rough the case up before spraying? got a picture of the front? I wonder how long it will last before it peels...
Click to expand...
Click to collapse

[Guide]How to modify changable battery[English version]

supplies : a phillips screwdriver, star screwdriver, snap-off blade cutter, sandpaper, guitar peak or your nail, scotch tape
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
they are screwdrivers what I'm using ^_^
1.Loosen a screw.
phillipse 4
star 6
totally, we need to loosen 10 screws. ( I don't know why xperia s use two method lol)
2.Take off back cover.
open HDMI cap, and spread back cover with your nail or kinds of lever.
Then, spread othersides too.
warning!!!
Don't open cover too much.
A cable is connected at back cover and main body.
It is!
It's simply connected, so just lift little bit with guitar peak.
And then, separating finish!
3.Cutting back cover
modification changable battery is very very very simple
because,
1. seperate back cover, cut. finish
2.main body is safe and we will play with back cover that can play little roughly.
Let's cut~
first, remove insulating tape
if you think removing insulating tape is not good, you can cut little under of them
I think there is no problem.
You can do fast if you scrape edge of them with guitar peak or snap-off blade cutter
removing insulating tape finish!
now, cut red line.
I barely did with heating snap-off blade cutter with lighter + mother's help.
Wow! finish! let's use........OMG it gets stuck
because I just cut 1 line....
someone cut 2 line
but, I use sand paper.
I can see my effort that I did lol
Yeah, cutting is finish. now, assemble![beforehand, remove battery first]
(My picture is already assembled....)
assembling is
connecting cable of back cover,
inserting back cover to main body,
tighten screw.
4.Make that battery's seperation is easy.
If you see youtube that I link at down of this post, He make that battery's seperation is easy.
We can also make that!
Use our last supplies, scotch tape.
Get take pull it and attach each of two sides(level of difficulty : difficult lol)
Then you can get smooth-faced tape....board?(I can choose english word @[email protected];
Attach it at battery.
★☆★☆★☆★☆FINISH☆★☆★☆★☆★
My english is poor ~_~
NOW, there is no weakness of XPERIA S!!!!
I'm so happy~
I want you modify like that lol
It is so comfortable.
and modification back cover is not difficult.
so.........
goodbye.
OPPA GANGNAM STYLE!
reference video:
http://www.youtube.com/watch?v=BGxWHzqPsQc&feature=related&hd=1
who helps me : poby
recommend link of battery :
http://www.ebay.com/itm/27096568412...eName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
## I'm sorry but I can't answer question ^^
Photograph by Kkobuk (Camera: NIKON COOLPIX P100)
kkobuk's blog http://88turtle.tistory.com/
but whats the point of doing this?
....
It is so that you can have a removable battery I think.
Sent from my LT22i using xda app-developers app

[TUT] Search button backlight bleed fix

So... This came up in a discussion recently, and people find it annoying after a while, so might as well fix it!
Strictly speaking, this shouldn't void your warranty (as the warranty screws in the back are left untouched), however, any1 opening the phone will immediately know that it was oppened.
Let's begin:
1: Using a heat gun/hairdryer heat the edges of the screen (not too much).
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2: Using a case opener tool get in under the bottom edge of the screen.
3: Once the bottom is lifted work your way around the sides of the screen (reheat as necessary).
4: Apply heat to the top edge of the touchscreen and lift it gently using the top edge as a pivot point.
5: Congrats! Hard part over, the rest is a walk in the park. The following picture shows where most of the light bleeding happens. The bleed that interests us is the one in the lower right corner (or rather lower left in this pic as I'm an idiot as far as camerawork goes).
6: Cut a piece of the material of your choosing apply a bit of double sided adhesive tape and slap it right on top of the light bleed.
7: If you did a perfect job opening the phone you can reuse the factory glue to hold the digitizer in place, however as that is unlikely proceed to removing the stray bits of the old adhesive tape and replace them with new tape (2 thin pieces on the sides, 1 fat piece on the bottom and 2 fat pieces around the flat cable on top)
8: Put the digitizer back in its proper place (slide the top in first and then drop the rest into place) and you're done!
Hope this helps!
Notes:
My cam sux... sorry
My workdesk choice also sux
The reason pics are missing for the gluing stage is that I need to replace the whole digitizer on this phone but the replacement part hasn't arrived yet so i decided not to glue it together as I will have to unglue it again this week.

Transparent Glass Back Mod

Hey guys. I have removed the paint from the glass back of my z5c. But all the adhesives i bought won't stay on (just like the stock ones). Where can i get really good quality adhesives to keep the back from popping off?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I think you need to heat the glue again to make it set. I would keep a bit of pressure on the back, like a book or something, after you've reheated it to ensure the glue sets in good contact with both surfaces.
But if all else fails I'd probably use a very thin bead of clear hardware silicone.
How did you get the paint off the glass?
lobie81 said:
I think you need to heat the glue again to make it set. I would keep a bit of pressure on the back, like a book or something, after you've reheated it to ensure the glue sets in good contact with both surfaces.
But if all else fails I'd probably use a very thin bead of clear hardware silicone.
How did you get the paint off the glass?
Click to expand...
Click to collapse
I have wasted around 3 brands of adhesives (all chinese) precut for z5c. Even the stock adhesive before I replaced it wont stay on. Could this be a design failure?
I havent tried to heat it and apply pressure yet. Might do that when my next batch of adhesives arrive. Do I leave it clamped overnight?
I just scratched/scraped it with a blade (cutter/knife) from the inside as it is also scratch proof. Other brands would have had a layer of plastic you could peel of but not this one. I just scraped everything off.
I haven't replaced mine yet. Waiting for my new battery to arrive. I'm replacing the battery at the same time to ensure the old battery hasn't swelled and could be putting pressure on the glass. That might be your issue too.
But i plan to make sure all the old adhesive is gone, heat up the new back and adhesive well and leave it under a few heavy books at least overnight and maybe for a few days.
lobie81 said:
I haven't replaced mine yet. Waiting for my new battery to arrive. I'm replacing the battery at the same time to ensure the old battery hasn't swelled and could be putting pressure on the glass. That might be your issue too.
But i plan to make sure all the old adhesive is gone, heat up the new back and adhesive well and leave it under a few heavy books at least overnight and maybe for a few days.
Click to expand...
Click to collapse
I have also replaced my battery as well. Actually, the battery was the reason i have opened it, aside from the dust under the camera lens. my adhesive still hasn't arrived yet. I will definitely try putting pressure on it overnight and report here.
Marke sure to clean the Glas and the opposide sie at the phone with string cleaner. For the Glas you can usw Aceton, for the phone sie you habe to check if it will survive Aceton. If in doubt, usw a weaker cleaner at the phone.

Moto 360 sport install lugs

I've had my 360 sport for a couple of years now and the band started to break. I fixed it with silicone but it only lasted about two weeks before breaking again. I decided to look for replacements but could not find any satisfactory way of replacing the bands. Since the watch was old and pretty unusable with the wristband broken I decided to try my own method and not be to careful about it...
I cut the bands and glued on lugs that were originally for a Samsung gear S3 (bought from Ali Express for ~$2) onto the watch. It actually worked great and now I can use whatever 22mm straps I want to! Here follows a more detailed description of what I did.
Materials used:
Razor blade, two-part epoxy glue, replacement lugs, replacement bands, small screwdriver (to remove excess parts from the lugs).
Price for entire replacement, lugs, epoxy and new wristband, was about 100 Swedish krona which is about $11.5 at the time of writing.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Power of the watch
Cut the watchbands close to the watch body
Using the lugs for measurement, cut the watchbands as close as you need to the watch body. (Warning: I carved so close that I carved into some metal, I'm not sure what it is for but my watch works so I gathered ether it was unimportant or I didn't cut deep enough to actually damage anything.)
Ad a bit of epoxy on the lugs and attach them in the correct position on the watch body, I used some tape to secure them while the epoxy dried.
After the first dab of epoxy dried (~10 minutes) I went back and added plenty of epoxy to the gap between the lugs and the watch body. I did this both to secure it more tightly and also to make sure the watch was still waterproof (or at least as waterproof as I could get it).
As my watch was an unattractive orange I used a permanent marker to paint it black with ok results...
Then I was done! The procedure was relatively simple and took about an hour maybe. I would say that the result looks good if your not closer then approximately one foot... The alternative is of course to 3D print a shell for the watch body but I found that ugly and I did not want to make it even more bulky. Overall I think this is a better way of replacing a broken strap. Thus I conclude with some final pictures, good luck to anyone trying!
This is actually awesome, thanks for posting. I can't seem to find those replacement lugs though. Any chance you still have a link?
Lugs
netzer119 said:
This is actually awesome, thanks for posting. I can't seem to find those replacement lugs though. Any chance you still have a link?
Click to expand...
Click to collapse
Hi!
I used these lugs: https://www.aliexpress.com/item/2Pcs-Stainless-Steel-Watch-Band-Connector-Adapter-20mm-For-Samsung-Gear-S2-RM-720/32882034607.html?spm=2114.search0104.3.75.7fa5590aX95YmZ&ws_ab_test=searchweb0_0,searchweb201602_5_10065_10068_319_10059_10884_317_10887_10696_321_322_453_10084_454_10083_10103_10618_10307_10820_10301_10821_10303_537_536_10902,searchweb201603_55,ppcSwitch_0&algo_expid=913f528c-c516-43a9-835e-ffc649f36426-10&algo_pvid=913f528c-c516-43a9-835e-ffc649f36426&transAbTest=ae803_4
A word of warning though. My battery life is worse now, the watch usually dies when battery hits 30%, not sure if the lug installment caused this but it might have... If i would do it again I would not cut as deep but rather fill in the gaps between lugs and watch with epoxy.
Hope it works out for you!
//Rasmus
I cut nothing, just install lugs adapter.
I have to remove back ring also, so rubber case will fit.

Categories

Resources