Download: Link
Steps:
1. Only works on EDL mode.
2. Run script 0-8475_update_image_EDL_fh_loader.bat
3. Update Official OTA package in recovery or install UserRAW in bootloader
Thanks ASUS Taiwan, @EdwardWu6688 , and don't use it for commercial purposes or earn money from this.
Does the bootloader version change with updates? What ROM is this bootloader compatible with? What bootloader version is used in the file?
_ReBoot_ said:
Does the bootloader version change with updates? What ROM is this bootloader compatible with? What bootloader version is used in the file?
Click to expand...
Click to collapse
Support 32.2004.2004.84
Big thanks for sharing!
Just a stupid newbie question:
Assuming the phone is dead (no recovery/fastboot) but start in edl mode (with edl cable). With this i can bring it back to live even if i flashed a totaly wrong firmware (wrong device for example)?
I want to start play around with custom recoverys/roms if they are available but before i want to know a way out of the worst case.
Im a newbie and I bricked my device
Does this support
Versión WW-32.2030.2030.26
?????
gaby704 said:
Im a newbie and I bricked my device
Does this support
Versión WW-32.2030.2030.26
?????
Click to expand...
Click to collapse
After you install this unbrick fw, you will get back to 32.2004.2004.84 bootloader, so you most need install 32.2004.2004.84 user raw or adb sideload 32.2004.2004.84 fully OTA package.
Ok I'll try it once i get the edl cable. Thank you very much for replying
Hi,
My Z9 is in bootloop following complete Magisk 25 uninstall ...
Is EDL a way to recover my z9 or not ?
A HowTo please ?
how i enter edl mode
i have an edl 9008 cable but i cant figure out how to enter the edl mode.
i plug it in and nothing happens, i went to bootlader and plug it in an again nothing happens
help please
And it wont show up on the port section of qfil
zegoo said:
Hi,
My Z9 is in bootloop following complete Magisk 25 uninstall ...
Is EDL a way to recover my z9 or not ?
A HowTo please ?
Click to expand...
Click to collapse
You should flash with RAW, Only if fail with rom then you can try EDL
Latest RAW -WW-AI2202-32.2030.2030.26-MR1-2208-M2.13.33.16-ASUS_1.1.1-user-20220816.zip
UnBrick (EDL) -QMSCT_ForCSC_DefaultFuseLock_AI2202_SM8475_31.1902.1902.55.zip
gaby704 said:
And it wont show up on the port section of qfil
Click to expand...
Click to collapse
Get From ROMDevelopers : AI2202_Provision_and_Flash_device_SOP_CSC.pdf
Inside have full guide, including EDL Test point ( How to entry EDL ) Full Guide.
In the guide (AI2202_Provision_and_Flash_device_SOP_CSC.pdf) is only the testpoint method described. I thought an EDLCable does the same without disassembling the device?
The provision.bat initialize the filesystem and the update-image-edl.bat does the firmware flash. Is this right?
Thanks.
Test point mean EDL mode, Just Short two point and follow guide..!
You don't have to EDL cable...!
AzimBahar said:
You should flash with RAW, Only if fail with rom then you can try EDL
Latest RAW -WW-AI2202-32.2030.2030.26-MR1-2208-M2.13.33.16-ASUS_1.1.1-user-20220816.zip
Click to expand...
Click to collapse
Thanks but where to find this RAW firmware ?
I used once the RAW firmware for my Z8 and it was the right way.
zegoo said:
Thanks but where to find this RAW firmware ?
I used once the RAW firmware for my Z8 and it was the right way.
Click to expand...
Click to collapse
You can check in ROMDevelopers as they have huge collection with latest data
AzimBahar said:
You can check in ROMDevelopers as they have huge collection with latest data
Click to expand...
Click to collapse
I tried but i dont't have an account with dfp. How to make it possible ?
Another way to get your RAW FW file ?
AzimBahar said:
Test point mean EDL mode, Just Short two point and follow guide..!
You don't have to EDL cable...!
Click to expand...
Click to collapse
Yes, but it should also work with the cable so i dont have to open the device?
Hermann2306 said:
Yes, but it should also work with the cable so i dont have to open the device?
Click to expand...
Click to collapse
If phone goes to EDL mode using cable, then YES. Otherwise ‘NO’
AzimBahar said:
Get From ROMDevelopers : AI2202_Provision_and_Flash_device_SOP_CSC.pdf
Inside have full guide, including EDL Test point ( How to entry EDL ) Full Guide.
Click to expand...
Click to collapse
I paid to download it but have no regrets. Thank you so! much it flashed
And my device is unbriked and functioning.
I really appreciate it. I spend days trying to figure out how to unbrick the phone.
So thank you!
Related
Multiple Tool Flash Recovery Check and unlock Bootloader
Download unzip somewhere inside PC and run with double click the Recovery-Tool.bat .
Follow instructions and check Bootloader Unlock *flash TWRP or Stock Recovery etc. Try it with your own responsibility.
Alternative you can put new TWRPS inside phone and Flash them through there as image files.
https://drive.google.com/file/d/1O3BgtajkXBT43pQBn66LeJ45G7tb_f5_/view?usp=sharing
Great ¡¡¡
Many thanks
Unlock stock 26s too?
dakok said:
Unlock stock 26s too?
Click to expand...
Click to collapse
Not yet..in the future..
senks bro
what does this do? And what does it mean for useage?
gaatjesprikker said:
what does this do? And what does it mean for useage?
Click to expand...
Click to collapse
Because I realized that you don't know.. so...with check bootloader tool you find out if your bootloader is locked or unlocked and you could proceed with safety to flash custom recovery to have the full abilities of this phone at your hands. Because if you try to flash any other Rom with locked bootloader you can have a full brick. And the second is that you have the power to choose between 2 recovery's or to flash back with 2 click's the official Stock recovery to have it if and when some Nougat or else Rom came out.
Doesn't work
Good day! Tried your program on my phone (5.8.020S, bought at jd.com) - doesn't work. USB debugging is on. Phone turned on in fastboot mode.
As a new user I can't post links to screenshots, may be I will send you a private message?
voldemaar said:
Good day! Tried your program on my phone (5.8.020S, bought at jd.com) - doesn't work. USB debugging is on. Phone turned on in fastboot mode.
As a new user I can't post links to screenshots, may be I will send you a private message?
Click to expand...
Click to collapse
Nothing is wrong. You just have locked your bootloader without permission to unlock. Did you put 26s with TWRP? THAT'S WHY. You must have stock locked allowed bootloader for unlock.
Great work !
Everything working well !
f2fs
If it possible to made f2fs working in recovery?
LordGiborg said:
If it possible to made f2fs working in recovery?
Click to expand...
Click to collapse
Search at BBS.le I think there is a custom with f2fs support.
CrisBalGreece said:
Search at BBS.le I think there is a custom with f2fs support.
Click to expand...
Click to collapse
Thx for your advise.
But it's really hard to find something there, and page loading sooooooooooo slow...
Thread closed on OP's request
Hi Guys. My HV10 was on on EMUI 9. I tried downgrading to EMUI 8 using HuRupdater but it won't boot now and is not responding to charger getting plugged in or out. I tried plugging it in on my pc and a dialog box opened saying "Configuring USB SER for use" then nothing. It's not showing up as adb and fastboot device. Kindly help.
HiteshK5 said:
Hi Guys. My HV10 was on on EMUI 9. I tried downgrading to EMUI 8 using HuRupdater but it won't boot now and is not responding to charger getting plugged in or out. I tried plugging it in on my pc and a dialog box opened saying "Configuring USB SER for use" then nothing. It's not showing up as adb and fastboot device. Kindly help.
Click to expand...
Click to collapse
You should be able to restore from a backup using Hisuite. There is a system recovery option also.
Sent from my BKL-L09 using Tapatalk
uncleabubear said:
You should be able to restore from a backup using Hisuite. There is a system recovery option also.
Sent from my BKL-L09 using Tapatalk
Click to expand...
Click to collapse
It's telling me to boot to fastboot which I'm unable too.
Update:- I think it's in testpoint mode. I don't exactly know what it is and how to exit it.
HiteshK5 said:
Update:- I think it's in testpoint mode. I don't exactly know what it is and how to exit it.
Click to expand...
Click to collapse
You need use DC unlocked to unbrick it. But you might need to open your device.
miststudent2011 said:
You need use DC unlocked to unbrick it. But you might need to open your device.
Click to expand...
Click to collapse
It's not on the supported devices list. Should i continue?
Delete
HiteshK5 said:
It's not on the supported devices list. Should i continue?
Click to expand...
Click to collapse
Check mate 10 and 20 forums there are guides to solve your problem.
Hisuite won't work as it's hard bricked.
Btw which emui 8 version build did you flash ?
What is its xloader version?
What build are you before using this method?
miststudent2011 said:
Check mate 10 and 20 forums there are guides to solve your problem.
Hisuite won't work as it's hard bricked.
Click to expand...
Click to collapse
It would be very kind of you if you can share the link.
miststudent2011 said:
Btw which emui 8 version build did you flash ?
What is its xloader version?
What build are you before using this method?
Click to expand...
Click to collapse
I was on EMUI 9.0.0.190 (not sure if this was the exact one, it was the latest version as far as I know)and tried to downgrade to EMUI 8.0.0.171. Dunno the xloader version.
Also I borrowed my friend's DC Phoenix account and was following it's guide. Does anyone know which board this phone has so that I can download it's software.
HiteshK5 said:
It would be very kind of you if you can share the link.
I was on EMUI 9.0.0.190 (not sure if this was the exact one, it was the latest version as far as I know)and tried to downgrade to EMUI 8.0.0.171. Dunno the xloader version.
Also I borrowed my friend's DC Phoenix account and was following it's guide. Does anyone know which board this phone has so that I can download it's software.
Click to expand...
Click to collapse
Where are you from?
From India ?
If yes just go to service center they will solve the issue.
I am on mobile cant Give you the link right now.
If you go to my profile you can find a thread by me in Honor 10 forums about hard brick info there you can find the link to mate 10 forums.
miststudent2011 said:
Where are you from?
From India ?
If yes just go to service center they will solve the issue.
I am on mobile cant Give you the link right now.
If you go to my profile you can find a thread by me in Honor 10 forums about hard brick info there you can find the link to mate 10 forums.
Click to expand...
Click to collapse
Yep, from india. Trying to avoid going to the service centre as it's like 25km away from my house
Will check the forums.
Any idea about the board which this phone has. Want to try DC Phoenix
HiteshK5 said:
Any idea about the board which this phone has. Want to try DC Phoenix
Click to expand...
Click to collapse
-open up device
-install com1.0 drivers
-touch testpoint
-flash a working bootloader via DC-Phoenix BUT UNCHECK 'FLASH OEMINFO' ; when you are back in fastboot mode :
-DON'T USE a BoardSoftware file.
-just flash your B190's update.app with DC-Phoenix
oslo83 said:
-open up device
-install com1.0 drivers
-touch testpoint
-flash a working bootloader via DC-Phoenix BUT UNCHECK 'FLASH OEMINFO' ; when you are back in fastboot mode :
-DON'T USE a BoardSoftware file.
-just flash your B190's update.app with DC-Phoenix
Click to expand...
Click to collapse
It's already coming as COM 1.0 in device manager. Trying to flash update.app (only fastboot part) but it shows no device detected to upgrade. Had downloaded a board software and clicked update button. I clicked update button and it detected the device but showed that I don't have enough credits.
oslo83 said:
-open up device
-install com1.0 drivers
-touch testpoint
-flash a working bootloader via DC-Phoenix BUT UNCHECK 'FLASH OEMINFO' ; when you are back in fastboot mode :
-DON'T USE a BoardSoftware file.
-just flash your B190's update.app with DC-Phoenix
Click to expand...
Click to collapse
What are exact testpoints for V10? since there is no officially images with testpoints for V10.
It's available inside DC-Phoenix apps...
I don't have the tools to open the phone. Maybe l will need to go to a service centre on Monday. If possible please try to help in fixing this phone.
oslo83 said:
It's available inside DC-Phoenix apps...
Click to expand...
Click to collapse
Not for view10
Hi i have same problem my V10 is Brick Not ON, nOT go in Fastboot mode my Model is BKL-L09 i have downloaded DC-Phoneix in possible repair?
LTE
Sent from my Vfone 6++ using Tapatalk
Hi all,
Im in trouble with my phone beacuse im in demo mode, is there any option to full update.
Ps. I updated to 9.1, but cust rom and preloader are same (maybe cause bootloader is locked, frp unlocked).
I need your help, please!
I check my model I used hisuite method.
basic: 9.1.0.300
cust: 9.1.0.21
preload: 9.0.0.17
As you see preload stick in 9.0. I guess that is kind normal.
PS. You can check before you flash if using Hisuite.
If your model is supported by Hisuite nvm
1. If not,edit C:\Users\yourusername\AppData\Local\HiSuite\userdata\UpdateDogDev\HiSuiteConfig.xml
by replacing either LYA-L09/LYA-L29 to your specific model and then use system repair function via fastboot.
2. Go check C:\Users\yourusername\Documents\HiSuite\ROM
you can see basic/cust/preload version officially supported if some still in 9.0 then It meant to be 9.0.
Good luck
q13017 said:
I check my model I used hisuite method.
basic: 9.1.0.300
cust: 9.1.0.21
preload: 9.0.0.17
As you see preload stick in 9.0. I guess that is kind normal.
PS. You can check before you flash if using Hisuite.
If your model is supported by Hisuite nvm
1. If not,edit C:\Users\yourusername\AppData\Local\HiSuite\userdata\UpdateDogDev\HiSuiteConfig.xml
by replacing either LYA-L09/LYA-L29 to your specific model and then use system repair function via fastboot.
2. Go check C:\Users\yourusername\Documents\HiSuite\ROM
you can see basic/cust/preload version officially supported if some still in 9.0 then It meant to be 9.0.
Good luck
Click to expand...
Click to collapse
Does this mean it will remove the demo mode?
Shkelqim.rexhepi said:
Does this mean it will remove the demo mode?
Click to expand...
Click to collapse
My, this is the same as the photo. How is yours? and how is this mode of demonstration? How did you get into it?
douglasmietto said:
My, this is the same as the photo. How is yours? and how is this mode of demonstration? How did you get into it?
Click to expand...
Click to collapse
Its the almost the same... You got same version of custom and preloader
did you tried to just unstick demo mod under developper options??
Why your phone is in demo mod? what's happened?
Shkelqim.rexhepi said:
Hi all,
Im in trouble with my phone beacuse im in demo mode, is there any option to full update.
Ps. I updated to 9.1, but cust rom and preloader are same (maybe cause bootloader is locked, frp unlocked).
I need your help, please!
Click to expand...
Click to collapse
You can turn off demo mode in developer option.
Hi after long time when i repaired my phone i saw that my build is ane-lgrp2 and i cant change it to ane-lx1 and that means that I can't downgrade it to oreo
Is there any way to change it?
erpl said:
Hi after long time when i repaired my phone i saw that my build is ane-lgrp2 and i cant change it to ane-lx1 and that means that I can't downgrade it to oreo
Is there any way to change it?
Click to expand...
Click to collapse
https://forum.xda-developers.com/t/...0-0-046-070f-emui-8-0-0.4324543/post-85538623
-Alf- said:
https://forum.xda-developers.com/t/...0-0-046-070f-emui-8-0-0.4324543/post-85538623
Click to expand...
Click to collapse
before you posted it i tried flashing it throught twrp and now i have black screen in fastboot mode
erpl said:
tried flashing it throught twrp
Click to expand...
Click to collapse
and what have you tried to flash ?
-Alf- said:
and what have you tried to flash ?
Click to expand...
Click to collapse
the emui 8 for this phone ane-lx1 https://androidhost.ru/5O5 after it finished i wiped cache and rebooted and now i have bricked phone
erpl said:
the emui 8 for this phone ane-lx1 https://androidhost.ru/5O5 after it finished i wiped cache and rebooted and now i have bricked phone
Click to expand...
Click to collapse
You can only install Service ROM using the dload method.
In addition, you tried to downgrade by installing a service ROM, which is highly discouraged!
If the computer recognizes the phone as USB SER, test point & board software must be used (or DC-phoenix ).
-Alf- said:
You can only install Service ROM using the dload method.
In addition, you tried to downgrade by installing a service ROM, which is highly discouraged!
If the computer recognizes the phone as USB SER, test point & board software must be used (or DC-phoenix ).
Click to expand...
Click to collapse
I think i will stop using Huawei phones because of hard repairs and mods i will buy new phone tomorrow because i don't want to rescue it anymore it's been nice 4 years with this phone 🫡
I've been digging and scouring for a long time but here you guys go here's the link to the firmware
https://service-sg-cdn.myoppo.com/CPH2417export_11_A.11_2022101923250170.zip
Is this really an unbrick solution? a little context would help, is it global / india / EU file?
How do you flash it without killing the phone beyond user repair?
Instructions or link to video or website with tutorial would be nice thanks
Its just the official Incremental Update direct from OPPO's servers.... same usage as other EDL flashes. If you can get it flashed it will guaranteed unbrick your device. It wipes the entire file system then loads the default OEM fw. No errors capable! If it flashes, you're unbricked
beatbreakee said:
Its just the official Incremental Update direct from OPPO's servers.... same usage as other EDL flashes. If you can get it flashed it will guaranteed unbrick your device. It wipes the entire file system then loads the default OEM fw. No errors capable! If it flashes, you're unbricked
Click to expand...
Click to collapse
But there is no EDL flasher for us consumers for the 10T so this file alone is useless unless i'm missing something!
leezaal said:
But there is no EDL flasher for us consumers for the 10T so this file alone is useless unless i'm missing something!
Click to expand...
Click to collapse
Qpst can flash the file
AkayamiShurui said:
Qpst can flash the file
Click to expand...
Click to collapse
That sounds great can you link a youtube video showing this or a working tutorial confirming this actually works??
leezaal said:
That sounds great can you link a youtube video showing this or a working tutorial confirming this actually works??
Click to expand...
Click to collapse
Sadly not my phone isn't bricked so I can't show it off but if you need help I can try to Walk you though it
AkayamiShurui said:
Qpst can flash the file
Click to expand...
Click to collapse
i thought only oneplus tool could flash it because it has a code blocking other software