I have a QTEK PH20B. I need a Firmware that will allow me to change the band. currently when using the phone, it does not pick up on the 1900 band. always no service, but it works fine on the 900 band.
device information
ROM Version 1.40.00 WWE
ROM Date 03/10/05
Radio Version 1.12.00
Protocol Version 1337.42
Ext ROM 1.140.147
hi im using the qtek 1010 with this information
ROM VERSION 4.01.16 ENG
ROM DATE: 02/04/2004
RADIO VERSION 3.23.00
PROTOCOL VERSION 32S54
THE PROBLRM IS IM IN LEBANON AND WHEN I INSERT SIM CARD BY PHONE SAY NO SIGNAL
ANY HELP HERE PLEASE
check the back of ur xda whether it is model: PW10A or PW10B, here in Egypt the PW10A is the working model, and i think it is the same at lebanon. inform me with the result!
King_hatem said:
check the back of ur xda whether it is model: PW10A or PW10B, here in Egypt the PW10A is the working model, and i think it is the same at lebanon. inform me with the result!
Click to expand...
Click to collapse
same here man in the back i have PW10A
i have o2 xda and
rom 4.02.04 eng
rom date 8/24/05
radio version 6.25.02
protocol version 324e4
but i am liveing in egypt and my pc pocet is working and gms ok but network is not working why and what is radio version dawonload plz any one tell me
Your device is designed for 900/1900 MHz Networks. I'm not 100% sure, but I think in egypt you have 900/1800 MHz networks.
So you can only use a provider that uses the 900 MHz frequency. Otherwise there is no possibilty to get it working. It's a hardware limitation and does not depend on the Radio Stack....
Stefan
Hi,
i have buy a used Siemens SX56.
Rom version: 3.17.03 Eng
Radio: 6.12
Protocol: 324e4
I have found Device information>identity tha is the model PW10A1 but in the rear of the pda is PW10B1 ?!?! What is possible?
In Setting>connection>connections>internet setting i have write my gprs parameters but i don't see the phone number!
The rom version and radio version is ok?
Thanks
Re: Help with gprs Italian WIND carrier and other problem...
klikkete said:
I have found Device information>identity tha is the model PW10A1 but in the rear of the pda is PW10B1 ?!?! What is possible?
Click to expand...
Click to collapse
Just the rear sticker is impotant. You have PW10B device.
This device is just capable of 900/1900 MHz networks.
Stefan
Re: Help with gprs Italian WIND carrier and other problem...
Ok...
can you tell me the optimal configuration for rom+radio?
What version?
Thanks
LumpiStefan said:
klikkete said:
I have found Device information>identity tha is the model PW10A1 but in the rear of the pda is PW10B1 ?!?! What is possible?
Click to expand...
Click to collapse
Just the rear sticker is impotant. You have PW10B device.
This device is just capable of 900/1900 MHz networks.
Stefan
Click to expand...
Click to collapse
1. Is O2 XDA is the same models like Siemens SX65 AT&T wirelles?
http://www.pdagold.com/hardware/detail.asp?d=124
.: Extra info & Model comparison
Sold in Central Europe as O2 XDA by O2
SIM-free O2 XDA sold by Expansys
Sold in North America as Siemens SX56 by AT&T
Sold in Sweden as Qtek 1010, previously known as Joey
Sold in several countries as T-Mobile MDA by T-Mobile
2. When i download upgrade in http://www.my-xda.com/xda_soft.html and i install to my PDA Siemens SX65 AT&T, now my PDA doesn't have any signal event i change my SIM Card??
this is the name file : Radio_Stack_Upgrade_v421 and Radio_Unit_Upgrade_v31703, when i download Radio_Stack_Upgrade_v421 then after restart, my PDA is no signal, so i don't continue to install Radio_Unit_Upgrade_v31703.
Note: when i install, my sim card still plug-in.
the network only :
ST-GSM-SGP
ST-GSM1800-SGP
Globe
AIS GSM
OPTUS
AirTel
SPICE
dont have TELKOMSEL (indonesia).
Can u help me to fixed my PDA,???
What model do you have? Check the rar sticker...
PW10A are for 900/1800 MHz
PW10B are for 900/1900 MHz
Stefan
different name
LumpiStefan said:
What model do you have? Check the rar sticker...
PW10A are for 900/1800 MHz
PW10B are for 900/1900 MHz
Stefan
Click to expand...
Click to collapse
opps...thank for your advice, now i have different name in my PDA, in the sticker label is PW10B1 and in my device information Identity the model no is PW10A1... ehm? i need your advice again to fixed my siemens PDA, thank you..
gohengky said:
opps...thank for your advice, now i have different name in my PDA, in the sticker label is PW10B1 and in my device information Identity the model no is PW10A1... ehm? i need your advice again to fixed my siemens PDA, thank you..
Click to expand...
Click to collapse
Different names are no problem.
It depends on what rear sticker say. So you have a PW10B device. Tehreforen 4.xx Radio Versions do not work try the 6.xx
Also you have to ensure your provider works either on 900 or 1900 MHz....
Stefan
LumpiStefan said:
Different names are no problem.
It depends on what rear sticker say. So you have a PW10B device. Tehreforen 4.xx Radio Versions do not work try the 6.xx
Also you have to ensure your provider works either on 900 or 1900 MHz....
Stefan
Click to expand...
Click to collapse
Mr. Stefan..
i am confused.., ehm, so i must try 4.xx radio vers if doesn't work so i must try 6.xx , were i can found it?? http://www.romkitchen.de/ or where ... please help me, replace PW10A1 to PW10B1 again ..
now my device information after i change is :
bootloader V5.22
rom vers : 3.17.03 ENG
rom date : 05/15/03
radio vers : 4.21.00
Protocol vers : 32S54
Model no .: PW10A1
Platform : pocket PC
Is that correct ??
my sim card is TELKOMSEL - indonesia , GSM Dual Band (900 & 1800),
http://www.telkomsel.com/web/company_profile
Dear Mr. Stefan,
i really need advice ...
thank you.
PW10B devices require 6.xx RSU-Version. You should You should then also fix the bandwith to 900 MHz in Bootloader
http://wiki.xda-developers.com/index.php?pagename=ChangingBandsWithBootloader
RSU Version can be found on www.romkitchen.de/tools/
The displaying of PW10A in your system depends on the ROM and is complete unimportant.....
Stefan
now is fixed
LumpiStefan said:
PW10B devices require 6.xx RSU-Version. You should You should then also fix the bandwith to 900 MHz in Bootloader
http://wiki.xda-developers.com/index.php?pagename=ChangingBandsWithBootloader
RSU Version can be found on www.romkitchen.de/tools/
The displaying of PW10A in your system depends on the ROM and is complete unimportant.....
Stefan
Click to expand...
Click to collapse
Dear Mr. Stefan
Thanks for your advice, now my PDA Siemens SX65 AT&T is work again, But i am not follow your instruction..i use the other way..now i want to share my step to fixed my PDA :
1. Download Radio Unit 6.24 version, find at : http://www.yorch.net/ ---go to --- http://www.yorch.net/upgrades.htm
USA T-mobile Latest Radio Stack (Unofficial)
RU 6.24.00
2. Install RU 6.24.00 in to your PDA,put in /windows find in Windows Explorer.
3. Wait for a second, and then will search the network...
4. Success.....
my device information is PW10A1 and not PW10B1 (the label in the back pda) how come is still can work?? But,anyway its Ok,because my phone is work again..
Thank you for your advice Mr. LumpiStefan.
That is very interesting.I like it very much.where can i find it?
________________________________
Rm files
to : mukojin776
you can find at : http://www.yorch.net/ but i dont recommend you to modify your phone, if you have commitment, than do it.. and i am not & dont have responsible if your phone is death..
You can ask Mr. Lumpistefan advice if you want to upgrade or modify your phone.
Enjoy your explore...
Thank you.
How to use SX56 with Airtel(India)?
AirTel (India)? what happen with that? if your XDA (SX56) can work, so??? what do mind by that? your phone is blocked??or doesn't have signal?? can explain about that??