please help, my unlocked O2 xda, will not reboot.
If I soft reset it gets to the align screen and does not respond any further.
If I hard reset it stops at Boot loader.
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_FlashSD
reflash would be a path to choose
Related
I attempted to use SSK 2.6 R4R Gen.Y Edition Default Kitchen from
HTML:
http://www.sskusers.net/
on my phone earlier. It seemed like everything was going fine, until I was taken to the startup screen. It was frozen, and there was red writing at the bottom of the screen.
Because the phone is stuck on that screen, when I try to connect to ActiveSync, it doesn't recognize any USB devices.
I did try removing the battery. The phone turns off, obviously, but when I turn it back on, I'm back at the frozen startup screen again.
I have also tried doing a soft reset, and the hard reset. When I do a hard reset, it takes me to the bootloader screen, and lets me do everything, but when it reboots, I just end up in the same place I was before - with a frozen startup screen.
Any suggestions on what to do, and/or what could have caused it?
Just wanted to add:
I have Verizon, and did do the hard spl using Raphael_VZW_HSPL_035, which I got from
HTML:
www.ppcgeeks.com
Reflash a different ROM through usb from the bootloader.
dwizzy130
i would suggest flashing a new rom or maybe going back to stock first & then trying a new rom. i would say the most important part right now would be flashing from the bootloader. put the nbh file on the sd card using a media reader & then pop it back in the phone & flash it. thats the easiest way & wouldn't take but 10 minutes to accomplish. i wouldn't be too worried you should be fine. feel free to get at me privately if you need some help.
Help
If you installed Hspl then just hold volume down and power and press the soft reset key. it will reboot into the bootloader and will recognize via usb. Hope this helps. I had a endless loop when i tried flashing to energyrom and this got me back to mightyrom. u may want to try it http://www.mightyrom.com
I had installed Chucky rom(ChuckyROM-23136-Tabtastic.Sept.12.7z) on my htc hd2,i had also installed hspl( HSPL2_RUN.exe) around two months(in september 2010) back but i did not like it so today(25th november 2010) first i removed hspl through HSPL3_PKG.exe and put spl 2.08.0000( I DID NOT USE AN SD CARD TO FLASH THE SPL) and then flashed
Artemis_v430_0409_WWE.7z i.e RUU_Signed_0409.nbh through SSPL_RUU.exe and then it worked and was working properly but was hanging again and again so i soft reseted it two-three times and then i was installing a cab file but as soon as the installation started, it said "installation of so and so file.cab was unsuccesfull" then i tried dinik hybridia icon .cab again same thing happened so i soft reseted it and while soft reseting a complete black screen appeared and said "a program from an unrecognised software party was tried to install please press the upper volume button to reset the phone Note. you will lose all your data and the phone will completely reset itself or else press any other button to start normally" i pressed any button so it started loading normally but it has got stuck at that loading and is not doing anything after that ,
it is not connecting to the pc,the backlight of the keys is also not switching on , i have takin the video of it switching on and also of bootloader ,
what has happened to it and why is it not starting,please help?
also even after i flashed artemis gen 4 it is showing the chucky rom boot screen!
In the videos it gets stuck to where i have stopped the video and remains like that for hours(THE Video IS IN THE RAR FILE)
also i have warranty left so can i get it repaired by warranty???
PLEASE HELP ASAP
try a hard reset. turn the phone off, hold down both volume buttons, and turn the phone on, keeping the vol buttons held down. then when prompted,press vol up to reset it.
yes, you'll lose any data and modifications on your phone, it will be back to how it was right after you flashed it, but at least it will start up. better than how it is now, right?
nishankyadav said:
I had installed Chucky rom(ChuckyROM-23136-Tabtastic.Sept.12.7z) on my htc hd2,i had also installed hspl( HSPL2_RUN.exe) around two months(in september 2010) back but i did not like it so today(25th november 2010) first i removed hspl through HSPL3_PKG.exe and put spl 2.08.0000( I DID NOT USE AN SD CARD TO FLASH THE SPL) and then flashed
Artemis_v430_0409_WWE.7z i.e RUU_Signed_0409.nbh through SSPL_RUU.exe and then it worked and was working properly but was hanging again and again so i soft reseted it two-three times and then i was installing a cab file but as soon as the installation started, it said "installation of so and so file.cab was unsuccesfull" then i tried dinik hybridia icon .cab again same thing happened so i soft reseted it and while soft reseting a complete black screen appeared and said "a program from an unrecognised software party was tried to install please press the upper volume button to reset the phone Note. you will lose all your data and the phone will completely reset itself or else press any other button to start normally" i pressed any button so it started loading normally but it has got stuck at that loading and is not doing anything after that ,
it is not connecting to the pc,the backlight of the keys is also not switching on , i have takin the video of it switching on and also of bootloader ,
what has happened to it and why is it not starting,please help?
also even after i flashed artemis gen 4 it is showing the chucky rom boot screen!
In the videos it gets stuck to where i have stopped the video and remains like that for hours(THE Video IS IN THE RAR FILE)
also i have warranty left so can i get it repaired by warranty???
PLEASE HELP ASAP
Click to expand...
Click to collapse
What an utterly unfortunate situation!! Couple of questions/remarks:
1. Did you install HTC 3.14 ROM with your S/N from HTC's website before flashing Artemis?
2. You already removed HSPL, so I would advice to extract the 3.14 RUU file to your desktop and copy the custom.nbh file to your SD Card after having it renamed to leoimg.nbh (insert SD CArd into PC to do that).
3. Reinsert SD card in device and enter bootlader mode and the installation of 3.14 should start automatically.
4. After that download Artemis 43 and extract it to the folder where you're SSPL_RUU,exe resides. Bothe the custom.nbh and the SSPL file must be in the same folder!
6. Start SSPL_RUU and flash Artemis
7. After that first a hard reset and then a soft reset.
Also read page 1 - Flashing notes
This should to it for you,
regards, Kuzibri
P.S. I posted this also in Artemis thread
same problem
i've got the same problem, but i didn't install the rom artemis,
i restart the installation many time but i've got always the same problem
the display showing loading..... please wait with the chucky logo.
someone can help me???????
thank you
hi all, I have the zte Carl. I can't do a factory reset .every time I try, the result is a white screen on reboot and stuck there. I tried to do hard reset but still got white screen. the basic problem is that both home and dial button not working so I want to do a reset. I cannot even get my phone into recovery mode. white screen again. if. anyone can help?
With what key combination do you enter in recovery?
I tried flashing TWRP into my j100mu, which is not supported...
Now, the phone won't pass the boot up screen. It's not a boot loop, or at least I doubt it, since it's not rebooting, it just stays stuck at the boot screen. I tried opening recovery to do a hard reset, but it won't recognize the input and just show the boot up screen. By that I mean that when I press Up+Power+home, the phone just boots up like normal and stays at the boot up screen, though Down+Power+Home works fine, but the moment i release any of the button, it goes back to the boot up screen.
So is this fixable or do I have a brick in my hands?
Hi!
Last night my phone began to restart after using the evernote , entered restart loop and the hard reset enter the menu but I can not choose any option.
Since yesterday that does not stop the loop and I can not do anything.
Does anyone know what to do?
Thank you.