everytime i flash with nvid wm5 i have to install htc usb switch and select "serial" (its on "RNDIS")and then move on for wm6 upgrade else usb doesn't gets detected.
is there a more shortcut
anyone please? does everyone use this pathway only to flash on windows xp?
Related
first i was trying to upgrade system from O2
something goes wrong and ERROR showed
and i could only my xda in bootloader on
then i was trying to upgrade rom bootloader by mitty
i`ve done this steps :
you will lose all data on your device, and your sd-card, so make a backup first*
make sure there is no sd-card in your device.
boot your device into bootloader mode
by holding down the big action/navigator button together with the power button, and hard-resetting with the pen at the same time
now the display should say 'serial' and the bootloader version.
insert a blank sd-card
put your device in it's cradle
start mtty.exe
select 'usb' as the port in the mtty program.
type the followint command into the mtty window
d2s 60000000 00300000
this will write your radio rom to the sd-card
the last step takes very long and my pc hang up
so i treied to do the same once again but mtty showed me "usb port could not open"
and i dont know what to do know???
plz help me
sory my english isn`t good enough
regards
have you tried just putting the pda in the cradle without using mtty?
if it change status to usb serial you can run the flashtool again
Rudegar said:
have you tried just putting the pda in the cradle without using mtty?
if it change status to usb serial you can run the flashtool again
Click to expand...
Click to collapse
i have same problem...
Yes my xda-II change status from SERIAL to USB.
but in PC my xda-II detected as UNKNOWN DEVICE,
so i can't run FLASHTOOL.
i just hope if flashing to be run from sd-card
mine did that once so i rebooted and or changed usb port
Rudegar said:
mine did that once so i rebooted and or changed usb port
Click to expand...
Click to collapse
I did it, and tried to about 3 PC's winXP SP2,
and still detected as Unknown Device, i think its connector problem or hardware error
Apologies but have scoured all the threads and cannot seem to get to a straight answer!
Have a tocuh-dual which I attempted to update to the latest ROM from HTC and now I have the "tri-colour screen of death!) and can get no further,
The screen shows in thered band - RUUNBH | NIKI100 | SPL-1.16.0000 | CPLD-4. The white band shows "serial" and when I connect the USB lead it shows "USB".
But the PC does not recognise it at all and when I try to load a ROM or run MTTY nothing is found. How can I run a program on the touch if the PC will noit see it through the USB connection?
Any ideas?
Does your PC have active Sync installed? I had a similar problem when I installed a broken rom that would not boot up. I did a device reset using the stylus in the whole next to the USB, while holding the camera and power button to boot into the tri color screen. Once hear i plugged in my USB cable and ran a ROM install.
I hope this helps.
uncheck allow usb-connection in Active Sync
run mtty connect by USB
type "boot" without quotes.
same problem
i have got the same problem and can't get out of the tri-colour.
I try to connect with mtty and it says usb port cannot open. my pc can recognise it and in da phone it shows usb though, i don't really know why its not taking. if i type "boot" in mtty what will happen? cos when i click on com3 its opening but when i write "boot" nothing happening even with boot. any ideas guys? how to solve the problem????
Regards
u have to unckeck allow usb connection in active sync! then u can connect with mtty
Just one point - I am using Vista which does not use Activesync but Sync Centre and that does not give you the option to disable as far as I can see?
use xp
bodonline said:
Just one point - I am using Vista which does not use Activesync but Sync Centre and that does not give you the option to disable as far as I can see?
Click to expand...
Click to collapse
Use xp mate, cos vista has got some problems. normally for unlocking and upgrading i use xp. blow up the vista .
Regards
I will crank one up and let you know how it goes!
kill the task in the Task Manager... then u can connect with mtty
Tried killing the process but MTTY still says "USB port cannot open" - no idea what else to do?
If any Program use the USB Port ... no other Program can use the USB at the same time!
Hi! I tryed te fash my niki 200 with original rom! The flash is stopes to 42% and now i have boot mode with this message "Upgrade ROM code error! Please try again". I can not conect again to usb because i received message :"usb device not recognized". Mtty can not conect because i received the same message! There is another metod de make this device?
Have you flashed HardSPL?
Put your device into bootloader (hold b oth Camera and Power button while performing a Softreset via Stylus) and now you can theoretically flash your Provider ROM!
After that your device will work again!
I have not flashed hardspl! If i put the Niki in boot mode, show only "serial" on the screen with usb cable pluged and PC says "usb device not recocnized"!
Flashing in bootloader mode doesn't requires an ActiveSync connection so ignore it and start the ROM Upgrade! It's working, believe me! I've flashed my Niki with this method hundred of times!
I tryed to flash my niki in bootmood, but not working "error 260:conection"! My computer not recocnized my device (with or without activesync)!!!In bootmode on screen show "serial" and when i pluged the cable nothing happend (must see on screen:USB)! This is my problem!!! The computer does not alocate to my device a com port(USB). The same problem with MTTY (no USB poet detected). You understand me?
Maybe your USB drivers screwed up.
Trie with an other PC, this helped me one time.
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
bugytech said:
I tryed on other computer with Xp and other with Vista! The same problem! Not recocnized!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
I've got the same issue. Did you resolve this? I would like to find a solution
During the upgrade of jasjar to wm6.5
After synchronization by activesynic and format the old version
Restart the machine work and entered the boot Loader system
Screen appears, written by usb from the top and bottom of v1.00
And a message from windows xp says usb device not recognised
And stop everything ....
I tried to install the driver of the usb from the cd but the pc does not accept
also tried more pc by xp, seven, vista
But the same thing ....
What is the solution
[Q] Do I need "Active Sync" to use CustomRUU, or can it just be in the Tri-Color Boot Loader manager with the USB cable connected?
I assume you can flash without being in WM, if so, my WM install can stay very thin for android porting.
11011011
If you are going to flash by connecting to your computer via usb cable, and you are using a WinXP computer, you will need to flash via ActiveSync.
If a Vista or Win7 computer, you need the latest version of Windows Mobile Device Center installed and connected.
No, your phone does not need to be booted into WinMo to flash, you can also connect to your computer with your phone in bootloader, and then running the customruu,
(power the phone on while pressing volume down button, will see tri-color screen) but booting WinMo fully and connecting via ActiveSync or WMDC is recommended.
Or as an alternative, you can put your ROM on a small (I prefer 4gb class 2) sd card (not in any folder, just on the root of the card-preferably an empty card) and turn the phone on with the card in it the same way as if you were going into bootloader, and the phone should tell you what to do from there. (Just the ROM goes on the card, not the customruu.exe , only the file LEOIMG.nbh)
Just make sure you have HSPL installed, and make double sure you have a compatible ROM