New to the forums but read and searched a lot before posting.
I want to load Hard SPL but after the loader says "verifying information on the Hermes," it gives me an Error [240]: file open.
Any ideas? TY
Nothing? Help me out
First off , post your question in the offical thread.
Second, did you follow the instructions precisely?
It isn't hard to do.
allan1 said:
First off , post your question in the offical thread.
Second, did you follow the instructions precisely?
It isn't hard to do.
Click to expand...
Click to collapse
I got this error following the instructions, yes
he's probably using Vista
He isn't... He's using XP
josh054 said:
He isn't... He's using XP
Click to expand...
Click to collapse
Oh I see now... file open error.
you've got issues with your user permissions mate, I suggest doing this while logged on as admin, or failing that, run it all from the root of your HDD
I had this same error as well I reccomend what he said above also Make sure no firewalls are up AT ALL !
My firewall is what gave me this error message ... Hope this Helps
Aha! My firewall is on... I'll take it off and try it again.
Thanks you two... I'll report back
Yeah IT usually is the firewall.... Good Luck Bro And hope it works for you
Worked! Thank you
Error [240]: File open
The update utility can not open the requested file. Please check your update utility.
Get this error. I have good synchronization.
Go to page 116 of this thread - http://forum.xda-developers.com/showthread.php?t=296722
Its post #1160, you don't need to use the pc at all....
I prefer to use the sd card method to install os's too as I personally find it safer..
Cheers...
I have the same thing utility error 240. I turn off the firewall, the active sysc is good, and able to flash kaiser-HardSPLv1 but unable to flash new rom due to the 240 error. Help please?
siracer27, this is the Hermes forum... Can't really help with Kaiser...
Hope you didn't install Hermes Hard SPL on your Kaiser cos you will end up with a brick if you did...
I understand this hermes forum but try to search for error 240 and wasn't able to find it except here. any help, i have att tilt..
Only thing I can suggest is, if you're using XP, then upgrade the .net framework to 3.5.
Cheers...
Related
hi guys
i keep getting country errors when i try to upgrade does anyone have a .exe file or some thing to stop this. have seen dcs,s post about country errors but sory i dont under stand what to do help help.
regards kevin
Here is it...
1. Unpack it to folder with unpacked XDA2 update
2. Run one of those .bat files and wait until it will not finish...
3. Try to flash it...
Code:
if (!working)
{
goto step 2;
}
else
{
you = done;
}
These are batch files I'm using to handle it...
hlep
thanks beecher
nice name by the way but i must be a bit thick because i unpacked and still couldnt get me xda to accept the upgrade it keeps coming up with country errors thanks for your help.
kevin
I suggest you try my procedures. I know you say that you have already looked and don't understand what to do, but if you take your time and read it carefully for each step, you should be able to follow it.
It is not as complicated as it looks
himalaya upgrading
hi guys
thanks for your advice but after reading and working on it for 3 hours i finally went to bed at 12.30 and it still didnt install i am off again on wednesday so i will try then.
thanks kevin
would upgrading my 1.66 to a higher version also reset the CALL DURATION timers found in the device information?
No the call timers are not affected
tnx. i'll continue searching the forums to find out how i could reset the call duration.
I don't think it's possible.
Why do you want to do it?
There are progs out there to measure you calls -
http://www.hudsonmobile.com/
Woo Hoo !!!!!!!!!!
Saved my life, what a piece of cake much easier way to get around the country ID problem.
Now I can upgrade to O2's latest rom without any problem.
Thanks for the files and the advice
xda update
hi guys
thanks for the help but i still havent upgraded my phone i am at my wits end i have added in another post what comes up on my cmd prompt.
help help
kevin
Re: xda update
kevin.beecher said:
hi guys
thanks for the help but i still havent upgraded my phone i am at my wits end i have added in another post what comes up on my cmd prompt.
help help
kevin
Click to expand...
Click to collapse
Hi, I replied to a post of yours with the command prompt output
OK. The output in the DOS prompt above looks kinda all over the place. You have copied files over other ones, etc and its hard to tell the order in which you have done things.
You need to start again with an untouched set of nbf files. Then follow the instructions in my post in the correct order.
Click to expand...
Click to collapse
As you can see, I suggested that you start again with a clean set of nbf files. I also noticed that you hadn't updated the crc values for the nbf files (as in step 11 of my post). Also you put the operator as <O2> it should be O2 and <language> should be WWE.
It really isn't as complicated as it looks . If you read it all first, then follow each step slowly and accurately without missing anything out, you should manage it ok. If, however you still get stuck (but do try first) and you have MSN messenger, I can 'talk' you through it.
A few newb questions here. One, Will all of the Roms in here work on a XDA o2 Neo? I realy wan't WM6 with a touch interface.
Two, I tried opening the ROM Update Utility I get a error saying "The application has failed to start because RAPI.dll was not found. Re-installing the application may fix this problem." < What does that mean?
yupp.
i am running windows mobile 6 on my xda neo atm.
there are even german versions out.
just ask anime lover or check ppcfreaks.de
samson_420 said:
A few newb questions here. One, Will all of the Roms in here work on a XDA o2 Neo? I realy wan't WM6 with a touch interface.
Two, I tried opening the ROM Update Utility I get a error saying "The application has failed to start because RAPI.dll was not found. Re-installing the application may fix this problem." < What does that mean?
Click to expand...
Click to collapse
1) Yes, all roms can be used but read carefully about "how to update" (there is a sticky post about that), there are two different ways on how to update...
2) IMO that means you don't have activesync installed (you must use an actual version)...
Alternative.......
invd said:
1) Yes, all roms can be used but read carefully about "how to update" (there is a sticky post about that), there are two different ways on how to update...
2) IMO that means you don't have activesync installed (you must use an actual version)...
Click to expand...
Click to collapse
Or may be you can have a look here, too.
http://forum.xda-developers.com/showthread.php?t=353547
Enjoy~~~
I looked through all the sticky threads and the wiki, and it mostly makes sense now.
But, what is activesync? I have not seen a reference anywhere to it, to what I recal.
And what about the error that I am getting when trying to open the ROM update utility?
samson_420 said:
I looked through all the sticky threads and the wiki, and it mostly makes sense now.
But, what is activesync? I have not seen a reference anywhere to it, to what I recal.
And what about the error that I am getting when trying to open the ROM update utility?
Click to expand...
Click to collapse
ActiveSync is a piece of MicroSoft software wich connects your PPC to your PC. It is so elementary that it isn't mentioned in the guides. For every connection you want to make between PC and PPC you will need it. If not, your PPC cannot connect in a normal way to your PC. You can download ActiveSync for free at MS Downloadcentre.
As for the error, as said before it looks like ActiveSync isn't installed and therefore the connection cannot be made due to missing drivers.
Thanks a lot for the info, I realy don't know anything at all about this phone yet realy.
i tried to update to wm6.1
then my phone hanged to the boot loader screen.
i tried to reverse to the old way i get the error 300 invalid update tool,
i tried to upgrade the hardspl using the upgrade tool it replies the same error
i tried to use PVtemp, it replies the same.
can anyone help me ?! PLEASE URGENTLY
btw i've search the forum for answers specially http://forum.xda-developers.com/showthread.php?t=353547 which was very helpfull but still have the same problem,
crazy_luv said:
i tried to update to wm6.1
then my phone hanged to the boot loader screen.
i tried to reverse to the old way i get the error 300 invalid update tool,
i tried to upgrade the hardspl using the upgrade tool it replies the same error
i tried to use PVtemp, it replies the same.
can anyone help me ?! PLEASE URGENTLY
btw i've search the forum for answers specially http://forum.xda-developers.com/showthread.php?t=353547 which was very helpfull but still have the same problem,
Click to expand...
Click to collapse
replied to you, see my thread...
==Solution Found==
==Solution Found==
okay let me explain, the rom update utility shipped in PVtemp file seems not working and always gets that error 300.
i used ftp://xda:[email protected]
and the same nknbf file it worked fine till now it's 82% now wish me luck
am planning to do HARDSPL afterwards ..and reupdate with the WM6.1 again
WISH ME LUCK
crazy_luv said:
==Solution Found==
okay let me explain, the rom update utility shipped in PVtemp file seems not working and always gets that error 300.
i used ftp://xda:[email protected]
and the same nknbf file it worked fine till now it's 82% now wish me luck
am planning to do HARDSPL afterwards ..and reupdate with the WM6.1 again
WISH ME LUCK
Click to expand...
Click to collapse
good luck
what was the full path of the tool you used to fix the update tool problem? im getting the same thing and it sounds like you might have a viable solution, but the link is broken.
shizenyasuya said:
what was the full path of the tool you used to fix the update tool problem? im getting the same thing and it sounds like you might have a viable solution, but the link is broken.
Click to expand...
Click to collapse
http://www.4shared.com/file/57952591/3955ed98/NVID_RUU.html?dirPwdVerified=2948f2e
Flash to WM5 ( as the result..) with the about NVID
Only in bootloader
My htc could only start in bootloader mode and it seems to freeze in this mode(i can tell this because when i remove the cable it still writes USB in the left corner). How can i flash a rom to it. Please help me.
w4rius said:
My htc could only start in bootloader mode and it seems to freeze in this mode(i can tell this because when i remove the cable it still writes USB in the left corner). How can i flash a rom to it. Please help me.
Click to expand...
Click to collapse
where no one read my sticky thread??
In tried Sd flashing(none other way works(
it stops for 5sec on
"Checking SD content"
but the processbar doesn´t change and then it goes to bootloader without changing anything.
i have same prb with my imate kjam... i tried to upgrade now its dtuch on start..
and itoo getting error when i tried to instal no vender rom.. plz tel me guyz. plz help me.
ok ive searched everywhere and have not found a single person with this problem.
when i try to use the ruu thing it gets to the receiving information part and then gives me error 260. now that would be ok if i had vista. but i dont. i have xp.
i have the new hard-spl on it.
so im not sure whats going on. any suggestions?
isaacfank said:
ok ive searched everywhere and have not found a single person with this problem.
when i try to use the ruu thing it gets to the receiving information part and then gives me error 260. now that would be ok if i had vista. but i dont. i have xp.
i have the new hard-spl on it.
so im not sure whats going on. any suggestions?
Click to expand...
Click to collapse
If you learn to read & search properly 1st then you wouldn't have this problem! follow this link....... http://forum.xda-developers.com/showpost.php?p=1876442&postcount=5 & Mr Vanx's upgrade Guide here http://forum.xda-developers.com/showthread.php?t=299462
MODS, Please close this useless thread!
Hi guys,
my htc hd2 is giving a white screen at the startup since today,
when I press volume down and start it shows this:
PB81100 HX-BC
SPL-3.3.0000 XE
I can connect it through usb to the pc,
when trying to run hspl4 it gives me
critical error
flow 00000001
Error code 000000002
Description: USB Connect Failed.
any idea how to make it work again>
Thanks!
Are you sure it does not say SPL 3.03.0000 lol just picking I know it does as there is no SPL 3.3.0000. Any way sounds like you may need to update your drivers. You can either go to control panel and device manager and find your phone click on it to make the device drop down then right click on the dropped down device and select update drivers and then select from the internet, or go and download the latest ActiveSynce or WMDC versions as the have the updated drivers.
If this does not work try changing USB ports, changing USB cables, or even change computers. Also are you right clicking on the HSPL.exe and selecting run as administrator?
I followed all your steps, updated everything, and used hspl4 as admin
now I have this
Critical error
flow 00000006
error code: 00000014
description: unknown
any ideas
rpedro82 said:
I followed all your steps, updated everything, and used hspl4 as admin
now I have this
Critical error
flow 00000006
error code: 00000014
description: unknown
any ideas
Click to expand...
Click to collapse
Are you flashing using ActiveSynce or are manually putting your HD2 into bootloader and then flashing?
Try hspl2 (or 3 for tmous), I've seen once or twice where hspl4 fails for no known reason. (And vice versa,,, sometimes hspl4 works where hspl2/3 doesn't)
T-Macgnolia said:
Are you flashing using ActiveSynce or are manually putting your HD2 into bootloader and then flashing?
Click to expand...
Click to collapse
doing it manually
samsamuel said:
Try hspl2 (or 3 for tmous), I've seen once or twice where hspl4 fails for no known reason. (And vice versa,,, sometimes hspl4 works where hspl2/3 doesn't)
Click to expand...
Click to collapse
doesnt work with version 3 or 2 since my firmware is 3.03 he gives an error saying he doesnt find the firrmware
rpedro82 said:
doesnt work with version 3 or 2 since my firmware is 3.03 he gives an error saying he doesnt find the firrmware
Click to expand...
Click to collapse
This is a long shot here but run a Task 29 and then while you do not have a ROM on the HD2 try to run the HSPL.exe as administrator agian. Be warned that any info that is not backed up or save will be lost when you run the Task 29, so if you do not want to do it I understand.
T-Macgnolia said:
This is a long shot here but run a Task 29 and then while you do not have a ROM on the HD2 try to run the HSPL.exe as administrator agian. Be warned that any info that is not backed up or save will be lost when you run the Task 29, so if you do not want to do it I understand.
Click to expand...
Click to collapse
trying this one!
can also try downgrading the spl by flashing a correct but lower version stock rom, which would then allow you to try hspl2.
Of course, the quickest easiest (and often very successfull) thing to try would be a different PC. there are dozens of threads where people try everything for hours, no luck, but 2 minutes on a different machine and hspl is installed.
rpedro82 said:
trying this one!
Click to expand...
Click to collapse
first time it did around 14% then gave an error message saying it was corrupt,
then second, third, fotrth time it stays at 0% and says recovery failed.
rpedro82 said:
first time it did around 14% then gave an error message saying it was corrupt,
then second, third, fotrth time it stays at 0% and says recovery failed.
Click to expand...
Click to collapse
There is something that is not right here and I can not put my finger on it.
There is something not right hear but I can not put my finger on it. I got another digestion, but aftercthis one I think I am going to be tapped out. Take and run the HSPL 4 again but instead of flashing HSPL flash SPL 2.08.0000 and see if it will let you do that. If it will the you should be able to flash. SPL to it then.
T-Macgnolia said:
There is something that is not right here and I can not put my finger on it.
There is something not right hear but I can not put my finger on it. I got another digestion, but aftercthis one I think I am going to be tapped out. Take and run the HSPL 4 again but instead of flashing HSPL flash SPL 2.08.0000 and see if it will let you do that. If it will the you should be able to flash. SPL to it then.
Click to expand...
Click to collapse
tried it still error :
Critical error
flow 00000006
error code: 00000014
description: unknown
now with Task29 I get error 270 when trying to do it.
Tried on two different pcs, one vista, one xp same thing.
if someone has another idea it would be great!
rpedro82 said:
if someone has another idea it would be great!
Click to expand...
Click to collapse
Hey rpedro82, I have one more suggestion for you. Now if you don't want to try thisI totally understand as I would be a little leiry about doing it myself. Some of the other members here on XDA that have had the same issue as you of not being able to get past the splash screen and not able to flash anything. This is what they did, they toke and placed their HD2 in a sealed plastic bag and set it in the freezer for 10 to 20 minutes then as soon as they took it out they flashed their HD2. I think this helps for two reasons, one if you are having overheating issues it will of course help with that temperarily. Two cold makes things contract so if you are having a issue with the processor and the main board loading connection for whatever reason the cold allows them to restablish the connection at least temporarily.
put it in the freezer, then retried, still stays at 0%
aaarg, its so frustrating,
any more ideas someone?
samsamuel said:
can also try downgrading the spl by flashing a correct but lower version stock rom, which would then allow you to try hspl2.
Of course, the quickest easiest (and often very successfull) thing to try would be a different PC. there are dozens of threads where people try everything for hours, no luck, but 2 minutes on a different machine and hspl is installed.
Click to expand...
Click to collapse
Have you tried Samsamuels above quoted suggestion you might have luck with one of these suggestions.
Hello guys...
I really need help with this HSPL...And some expert advice too..
I have problem with my EU HTC HD2 with HSPL...
I try to put 1.42.HSPL with HSPL2_run so i can put beck stock rom but after that all thing is stuck...
My bootloader screen look like this
SYSTEM DON'T ALLOW ME TO PUT SOME LINKS..
and if i try to put beck 2.08.HSPL with HSPL2_run or HSPL4 he pop-up me some CRITICAL ERROR
Flow: 00000003
Error code: 00000004
Description: Bad model ID!
Do you know what can i do? I really need help...
Thanks a lot again..
Hi rpedro82
did you find any solution for your problem ? I'm facing the same problem and I'm still on the same point even if I tried all the members' suggestions here (even for the freezer) :/
Cheers,
GJ.