Recently installed WMWifiRouter 1.10 on my Sprint Touch Pro...
I did the internet sharing hack from the TP essentials thread.
WMWifiRouter starts fine but gives a fatal error at "Waiting for ICS and WLAN..."
The log is as follows:
Starting ICS
Waiting for connection...
Connection detected
Initializing... may take 10 sec
Setting up ICS interface registry
Turning on WLAN
Rebinding WLAN
Rebind: Success
Setting connection mode
ConnMode: Ad-Hoc - Success
Rebinding WLAN
Rebind: Success
Restarting WLAN
Waiting for ICS and WLAN...
FATAL ERROR
???
Terminating ICS
Restoring ...............ETC............
Any help would be great!!!
mynameisvinnie said:
Recently installed WMWifiRouter 1.10 on my Sprint Touch Pro...
I did the internet sharing hack from the TP essentials thread.
WMWifiRouter starts fine but gives a fatal error at "Waiting for ICS and WLAN..."
The log is as follows:
Starting ICS
Waiting for connection...
Connection detected
Initializing... may take 10 sec
Setting up ICS interface registry
Turning on WLAN
Rebinding WLAN
Rebind: Success
Setting connection mode
ConnMode: Ad-Hoc - Success
Rebinding WLAN
Rebind: Success
Restarting WLAN
Waiting for ICS and WLAN...
FATAL ERROR
???
Terminating ICS
Restoring ...............ETC............
Any help would be great!!!
Click to expand...
Click to collapse
Use ver. 1.25 It runs a lot better, and I'm guessing it is going to fix your problem. I have absolutely no problems with my Sprint TP and WMWifiRouter Ver. 1.25.
That was the ticket! Thank you!!!
Related
Hi everybody
I have a big problem:
when i lost the gsm signal the phone is power off and never recive incoming calls ... until i'll power on again.
Is there some settings in order to search the gsm signal always...?
...cause i can't control the xda every 5 minutes if have signal or not...
I have 4.21 radio and 4.00.11 rom
Thanks all
Denis
have you tried a hard reset? or even re-writtin the bios?
that worked for me
Hi Guys,
I need your help .
I've downloaded the 4.00.16 ROM by mistake, it really didn't tell the ROM number, so now I want to revert to a earlier one and I can't.
I've got the following message: "ERROR: GetDeviceData - An established connection was aborted by the software in your host machine.
error getting devicedata" and then "ERROR 011: EXECUTE REMOTE COMMUNICATION PROGRAM ERROR. Cannot execute the remote communication program. Please make sure that the USB/Serial cable is properly connected."
PLEASE HELP ME, I'M REALLY STUCK NOW AND DON'T KNOW WHAT TO DO...
Sorry ... when can i get the radio 6.24.00 ???
can work for Italy ?
What do you mean with "re-writtin the bios" ... ? the SD card boot ?
Thanks
Did one T-Mobile 3.17.03 rom just fine. Have 2 with 4.01.16 and get error: get connection type an existing connection was fociblyclosed by the remote host. error getting connection type. xda-developer-ser v1.2
Programme v1.09
Ichecked the device manager-okay. Firewall off-anti-virus off swapped between 4 2.0 USB's and 2 1.1 USB's changed connection pods-no difference.
Anyone have any suggestions? :x
Have you ever tried a search here in the forum?
I guess not....
The T-Mobile ROMS (e.g. 4.01.16) prohibit downgrade via active sync. Try downgrading via SD-Card......
Stefan
(Reposted from the thread dealing with the EEPROM issue)
2 days ago I upgrade my Dopod 838Pro to WM6. There were no issues experienced during the upgrade, but since doing it I have not been able to establish a connection to my AP. I have since downgraded back to the shipping version of WM5 in an attempt to get rid of this issue as I had no problems prior to upgrading.
One thing that I have found is that if I change my AP to be unsecured, using neither WEP nor WPA-PSK I can actually connect successfully, however as soon as I go back to WPA-PSK I again cannot establish a connection. I will try WEP next and post an edit with the results of WEP.
Update:
I have just tested WEP and it works also. Problem only seems to be with WPA-PSK security. Unfortunately I can't test any other APs - my router is a Netgear DG834T with the latest firmware on it. Does the Radio ROM version have anything to do with the WLAN/Wi-Fi/Wireless Adapter in my Dopod? I have no connection issue from 3 other PCs using WPA-PSK, the issues are specific to the 838Pro.
Device Information:
ROM version: 1.30.707.8
ROM date: 12/13/06
Radio version: 1.47.00.10
Protocol version: 32.80.7020.20H
I experienced this kind of issue where I work. There is a full wifi coverage and we can connect through WPA(2)-PEAP (mschap) or Open connection + VPN.
Since I updated to WM6, I was no more able to connect through WPA to the network. I connect fine to the open connection, but as I don't have the cisco vpn client on my hermes I cannot go any further.
I found no resolution to this; I asked the technical staff in-charge and all what they were able to tell me is that my handshake request doesn't even come to the RADIUS server.
At home I am also using wifi through WPA2 PEAP (cert) and it works fine. I had some issue at first (no connection possible with any WM devices I tested)with one of my access point, but updating its firmware had this fixed.
What you could try is to have your Access Point updated.
Let us know how you handle this issue.
One thing I noticed after upgrading was that wifi encryption defaulted to WPA2 with AES and I had to set it back to WPA-PSK and TKIP
I have a similar problem but i didnt upgrade to WM6 i upgraded to the latest Vodafone Rom.
I can connect to the internet via GPRS and whilst connected to my laptop via activesynch. but whenever i try to connect to my Netgear accesspoint it just sits at connecting untill it gives up. I am using wpa-psk too But it still doesnt connect when i remove all security
It worked fine before.
Not been able to test it on any other networks yet though.
any ideas i am running out
Rom: 2.07.161.1
rom date: 02/06/07
radio: 1.32
protocol: 32.65.7020.09h
i am expirencing the same issues on my Dopod 838 Pro running win mobile 5.0
My netgear router is set to WPA-PSK/TKP and other phones can connect to it.
However my dopod just sits on connecting and does nothing. If i try to surf the web my phone conect to GPRS instead of the wireless. Any ideas this is really frustrating??
I have problem with Wifi connection. I cannot get access to my Wifi AP (inside PC workstation: card Gigabyte).
I use HTC Athena with WM6 official HTC ROM (build 17745.0.2.3).
Beside Athena, I have on room others WM devices, and they are connecting to my Wifi AP without problems. For example Eten X500. I tried different authentication modes, WEP, WPA-PSK, nothing success. I'm sure all settings in Athena are the same as on my others devices. My AP is visible on Settings/Wi-fi dialog, and marked as "Available". but when I try to tap-and-hold this name, and select: Connect, then nothing will happen. It's displaying Connecting for a while, and then back to Available.
Is there any Wifi fix for HTC Athena?
I have the same Problem
I have an Imate JasJam and I am facing similar problems.
Here is what I have on my phone:
ROM - Black Satin
Radio - 1.43.00.00
IPL - 1.04
SPL - 1.20 Olipro
I recently flashed to this ROM image from the following web-site:
http://www.mrvanx.org/cms/index.php?option=com_content&task=view&id=62&Itemid=26
At first it worked for about 3-4 days. Now all of sudden it has stopped working.
- I see that the WiFi connects to my access point.
- I can ping the device from my PC - so seems like it's fine on the internal network
- I have office communicator installed on the device - this seems to connect to my company server - I can see my colleagues online/offline
- On the other hand - Live Messenger does not connect, IE cannot view any site. Says "Page could not be found. Check the spelling and try again"
I wonder what went wrong.
Anyone seen this issue?
Wifi Problem wm6
Hi
The problems you have explained possibly caused by the driver update on the pc for the Wifi AP. Try uninstall the Ap and delete the settings from the Ameo, Then set up the device with WPA- TSK settings after reinstall the Ap with new drivers.
Good luck.
Actually, I could not figure what was going on. It surely was an issue with my device. Since my laptop(s) could connect just fine.
I did a hard reset - clear storage and the problem is gone.
I think it could have been due to some software installation on the device.
Now, question is which is that software. I will keep an out for this and see what happens each time when I install a new software on the device.
Dear all,
Recently in HD2 I had some issues with the network signal and than i had to restart several time to get back the signal.
Than in one moment I got ARM 11 FATAL ERROR Flash_os_line.c line582 and no HD2 is working but cant connect to the network. HD2 is having HDSPL and in the tricolor screen I'm getting this: aaaaaaa HX_BC before the SPL and Cotulla HSPL.
I did google this problem but couldn't find similar problem for HD2, can anyone help?
Thanks in advance,
rilazi said:
Dear all,
Recently in HD2 I had some issues with the network signal and than i had to restart several time to get back the signal.
Than in one moment I got ARM 11 FATAL ERROR Flash_os_line.c line582 and no HD2 is working but cant connect to the network. HD2 is having HDSPL and in the tricolor screen I'm getting this: aaaaaaa HX_BC before the SPL and Cotulla HSPL.
I did google this problem but couldn't find similar problem for HD2, can anyone help?
Thanks in advance,
Click to expand...
Click to collapse
Anyone to help on this :-((((
ARM11 fatal error - Flash_os_wm.c line 582
The same error has appeared on my HD2 this evening!!
Have you or anyone come across a fix?
Thanks,
Sebster84
Same error!!! i had GPS issues with ginger bread so i undone HSPL(official NBH thru Sd) and same GPS error on windows RUU_Leo_hTC_Asia_India_1.48.720.2_Radio_15.28.50.07U_2.05.51.05_2_Signed_LEO_Ship. then it started having boot errors and if i talk more than 5 min the phone gets over heated and rebbots hangs on boot screen once it cooled off starts again! now this error after a 5 min call . phone works and can make the calls and all still............................
AMR 11 FATAL ERROR
FLASH_OS_WM.C LINE 582
line error in PHP i can understand whats this? dying processor? nand?
serched google and froum