Please help me...I aws reflashnig phone...and when it is flashnig, in progrees it is turning off a and I can´t start it...please help, please....
I only in boot loader but i must puss Camera button, on clasic start button = without reaction only blik leds....
In boot loader its write this:
RED field
Oxygen
ONBL 1.05.0000
GREEN field
Oxygen
SPL 1.05.0000
BLUE Field
Oxygen UI
And when I flashing ROM from this: http://forum.xda-developers.com/showthread.php?t=564531 its stop on 4% and turn off automatic
Please help, how with this?
It seems you haven't hard-spl. Try http://forum.xda-developers.com/showpost.php?p=1618402&postcount=1 this, or ruu-signed roms.
can you post here some RUU signed ROMs?
When I updating it´s wrote me error 270 or 294 invalid vendor id
I was test this roms:
RUU_Oxygen_1.5.411.1_4.1.13.20_02.41.90_R_HTC_RUS_Ship
RUU_Oxygen_1.5.70.3_4.1.13.24_02.48.90_Orange_RO_Ship
RUU_OxygenWM5_1.5.401.2_R3_4.1.13.28_02.67.90_HTC_EUR_Test
But everything, without change, when I give update ROM it´s stop on 4% and write error 270 update error - when I try HSPL or 294 invalit vender error - when I try ROMs
Who have kitchen for oxygen with rom?? i need it...
I have Qmat, I create HTC Gold Card, load rom to card but nothing happened...please help me...how...a need total info how to...
I need ipl, spl, some images to load, rom and etc...I need unbrick my phone...please help me
Related
After flashing my XDA2 to WM5 3.5a, i've tried merging storage & extended rom to gain memory by following a thread on Airfagev. After doing a hard reset, i found out that my phone is not responding and all i can see are black horizontal lines on the screen w/out backlight. I tried soft resetting it but still it stays the same.
Though i can still put it on bootloader mode, it also wont finish reflashing and an error message appears that goes like this:
ERROR 100: Model ID Error
The ROM image you are trying to use is not designed to work with your Pocket PC.
Is there any way for me to fix this problem? I really need help from anybody who's knowledgeable enough in solving this problem coz' i am new in this field.
Pls. help.
Thanks in advance!
Yoo can use NOID utility for flashing
HimaUpgradeUt_noID.exe
bootloader
Thank you. I can now reflash my device to WM2003 but not to WM5.I think it's because of the bootloader which is v 1.06.Is there any way to change this to v 1.03?
Help pls.
I tried to run unlocker, step 1 was successful but during step 2 there was an error and the program crashed.
Now the phone can enter bootloader when I switch on, when I try to flash a ROM I stays on %
Please help
sorry to hear that happend to you as you were trying to unlock your phone....
but when you enter boot loader what does it say at the top?
My athena also failed at upgrade... now, it only stops at opening logo..
I already have Hard-SPL installed but I don't find any program like HTC trinity Stack Overflow Exploit to unbrick it..
bootloader is still possible.. then what should I do?
and how do you use mtty?
Think before you jump to conclusions.
raf1987 said:
My athena also failed at upgrade... now, it only stops at opening logo..
I already have Hard-SPL installed but I don't find any program like HTC trinity Stack Overflow Exploit to unbrick it..
bootloader is still possible.. then what should I do?
and how do you use mtty?
Click to expand...
Click to collapse
Think before you jump to conclusions.
If it tries to boot and stops at the opening logo , the rom is corrupted but not bricked.
If you can get into bootloader you can usually resurrect without resorting to mtty ,which only really cmonex here knows how to use properly.
Check which SPL is visible in the bootloader screen and then flash an appropriate ROM.
ie SPL 1.1 > original ROM
SPL 1.2 > any spl 1.2 ROM.
lakeman said:
Think before you jump to conclusions.
If it tries to boot and stops at the opening logo , the rom is corrupted but not bricked.
If you can get into bootloader you can usually resurrect without resorting to mtty ,which only really cmonex here knows how to use properly.
Check which SPL is visible in the bootloader screen and then flash an appropriate ROM.
ie SPL 1.1 > original ROM
SPL 1.2 > any spl 1.2 ROM.
Click to expand...
Click to collapse
If you put it in bootloader screen (FULL PRESS camera button, while poking reset hole) What does it say on the "SPL" line eg; 1.1, 1.2, or 3.5? and what ROM are you trying to use?.................Hi Lakeman
Jay
athena x7500
please help. i have the same problem.
after flash with athenaunlocker after step 1 ,in step 2 my athena make error and my x7500 cannot power on but i can put it in bootloder made.
when i want to flash it with other rom it take 12% and show error.
who can help me please.
ATHE100
IPL-v2.02
ATHE100
SPL-v1.20.Olipro
help please
likebie said:
who can help me please.
ATHE100
IPL-v2.02
ATHE100
SPL-v1.20.Olipro
help please
Click to expand...
Click to collapse
you have to load an spl 1.2 rom while in bootloader
make sure you remove your sim and sd card first
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
Have you took the sim card and memory card out?????
Jay
yes they are both out when tryign to flash, been over a week with out a working athena
cowballz69 said:
yes they are both out when tryign to flash, been over a week with out a working athena
Click to expand...
Click to collapse
try flashing your original ROM which should be found in the wiki section.
ignore what I said below and report back if you were able to load your original ROM
***Ignore this read above**Once your phone is working , do the athena wrapper which should load SPL 1.2
Also read this
http://forum.xda-developers.com/showthread.php?t=429013
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
cowballz69 said:
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
Click to expand...
Click to collapse
I think this means your phone is not unlocked
with respect to sergiopi , you cant do the mtty script.
I would suggest you msg cmonex or try to talk to her on IRC on the
dxa-devs channel
addendum
seeing that you have nothing to lose, why dont you try flashing the original rom from the sd card using the method in the wiki
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
I have the same problem.
what I do...
I have ameo t-mobile...windows mobile 5.0
run AthenaUnlocker
Step 1 make all finish noc problem
Step 2 hung up on 60 %
bootloader no problem....but can´t flash original flash always stuck at 1% and reboot...
flashing the original rom from the sd card using the method in the wiki ...
make it, but no do...on screen see
cheking...
loading....
than come on screen
0002802
ching...
loading...
not allowed
sergiopi said:
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
Click to expand...
Click to collapse
My error when it stops at 1% is "invalid vender id"
my image version is demaged
Re: Ameo from t-Mobile german - repair
________________________________________
hi
what is your CID? use mtty command "info 2" to find out.
for example, if it is TMOB_007, you have to find a shipped athena rom with that CID.
if you cannot find a matching rom, let me know, i can still help,
cmonex
HTCS Þ?ÒtHTCE
please need halp
thx
felix999
read this post http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
in mtty this can read:
when type task 32
become LEVEL: FF
when type info 2:
HTCS Þ?ÒtHTCE
my CID is 1.1
on bootscreen can see this:
ATHE100
IPL-v1.00
ATHE100
SPL-v1.10.RP00
what I do before...
Ameo WM 5.0 >>>>my mistake not update to WM6.0
run AthenaUnlocker
STEP1>>>OK
STEP2>>>by 60 % hang and stopped....
and now have the big problems.....Image ROM of t-Mobile 5.0 german demaged
can´t flash any rom´s
thx for hel or I want to pay bucks for service, when ma ameo live again...
felix999
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
this is my CID
Cmd>info 2
info 2
Wait interpreter timeout
HTCS Þ?ÒtHTCE
????????
don´t know
felix999
Athena mobile 6 > SPL 1.10
become today a answer from crazy cat, that olipro say must take an rom in athena forum....
I flaswh with so many roms...anytime same error: error 294 - invalid vendor ID.....
My SPL 1.10 >>> can´t find a rom with SPL 1.10
what rom can repair my demaged ameo?????
thx for help
felix999
problem solved with ONLINEHELP from>>>>>cmonex>>>><<:::::>><<:::E:::>><<:::R:::>><<:::F:::>><<:::E:::>><<:::C:::>><<:::T:::>>
thx
felix999
lakeman said:
try flashing your original ROM which should be found in the wiki section.
Click to expand...
Click to collapse
Is this how you solved your problem?
hi every 1 ...
here is the situation i'm in:
Each time I tried to upgrade my HTC Touch Dual with another Radio(like 1.71 or 1.65) ,i prosed with the operation but it did not complete for an error on 100%!! then my phone was stuck on the three colors Screen with some words:'Upgrade ROM code error Please try again'
RUU_ERROR_226 FLASH WRITE
But It semms allright when I managed to upgrade a ROM without radio...
Please help me ....
Regards.
P.S. three colors Screen with following words:
RUUNBH
NIKI100
SPL-1.22.Hard
CPLD-4
Upgrade ROM code error
Please try again
Serial(or USB)
I upgrade a Chinese version ROM.... And everything is okay now.....
so strange.....
Hi people,
I got a problem with my hd2.. I was trying to flash it, but now i think i ****ed it up!..
First of all i did the HSPL thing.. And then i was trying to flash it with the original update 1.66 flash..
My mobile was saying that it was not allowed!
Now everytime i start my phone you get the bootloader with the message:
PB81100 HX-BC
SPL-1.66.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Updrade ROM code error Please try again!..
I dont know what to do right now
Please help!
and if i try a custom rom.. it says loading... all the time?
Is there someone who can help me?
Did you tray a method with SD card?
First of all you have to format a memory card to FAT32. Then put there a image of original rom. Do do so you need download stock rom from HTC and extract it. There you find a *.nbh file, the largest one. Rename it to LEOIMG.nbh and copy to your SD card.
After that put it into a phone, an enter the bootloader mode. You have to press and hold volume down key. That's all. All you need now is to follow instructions which will be displayed on screen of your phone.
yes i did.. but ill tried the original rom:
RUU_Leo_HTC_NLD_1.43.404.1_Radio_Signed_15.26.50.07U_2.04.50_22_2_Ship
But that one is saying: Not allowed :|
you are not the first one this happened to.
look here
http://forum.xda-developers.com/showthread.php?t=618084
here
http://forum.xda-developers.com/showthread.php?t=631276
here
http://forum.xda-developers.com/showthread.php?t=631053
it looks like hspl is not installed on your device with the line SPL-1.66.0000 XE on the screen. it should read SPL-1.42.HSPL XE when it is hsplled. flash the original shipped rom again from bootloader with a goldcard or reflash the hspl
redownload your rom as it might be corruped and causing a bad flash
especially look in the firstlink i gave you.
you have tried to flash 1.66 this is a WWE or ITArom. your device is not hspl-ed so it will not accept a dutch rom. you need a goldcard to flash a dutch rom again or try to reflash a stock WWe rom.
If you are Dutch or using NLD (or equavalent)
Get the official (from htc) ROM, rename the EXTENSION to .ZIP an/or open it with Winrar.
There is a .nbh file in it, wich you need to extract to (for example) your desktop.
Rename it to LEOIMG.nbh and put it on your MicroSD (wich MUST be formateed FAT32)
Put your microSD in the phone.
Start your phone in the BOOTLOADER (keep VOLDOWN pressed and shortly press POWER .. while keeping the voldown button)
Follow the instructions on screen.
Wait till all the options say OKE, even if your phone goes running trough the room, dont click anything!
(you will see some explanation marks and reboots, this is normal).
After you should have flashed SPL 1.66 and able to boot the official ROM.
But the problem is.. All the original roms doesnt work.. They Say "00028002 Not allowed"
The ROM error is because you try to downgrade 1.66 to 1.48, wich is (i think), not allowed, and would answer my own qeustion.
have you tried the goldcard method? if there is a language restriction somewhere this will solve this
I dont understand that goldcard methode.. or.. i cant find how i can do that :$
have never needed itmyself but look here
http://forum.xda-developers.com/showthread.php?t=591239&highlight=goldcard
How can i make a goldcard without a cellphone who can start? :O
same here....
my hd2 successfully hspled... ( 4 mounths ago)
after that i try to install official 3.14.405.2 Rom...
in installing progress i see a error and after restart say: software update failed please try again
now my spl is 3.03
and task29 and hspl 1 and 2 and 3 and any orginal roms NOT installed in my htc hd2...
plz help! :-D i really really confused
tighoor said:
same here....
my hd2 successfully hspled... ( 4 mounths ago)
after that i try to install official 3.14.405.2 Rom...
in installing progress i see a error and after restart say: software update failed please try again
now my spl is 3.03
and task29 and hspl 1 and 2 and 3 and any orginal roms NOT installed in my htc hd2...
plz help! :-D i really really confused
Click to expand...
Click to collapse
You need to remove SPL 3.03!!
Only way to remove is to flash stock rom over SD!
kurt-willems said:
You need to remove SPL 3.03!!
Only way to remove is to flash stock rom over SD!
Click to expand...
Click to collapse
i tried it... but not installed from sd :-S hahaha! now i have bricked hd2. who buy it?
maybe cotulla should make a new hspl that support 3.03 . true?
Same here,flashing stock ROM from the SD Card doesnt help,the SPL 3.03 is there wont let me pass through,we need a new HSPL or else throw the Phone into the garbage can and get a NOKIA.!!
now i understand this is a problem for many users... i find 3 others users that have this problem (in iranians forum)...
My problem too!
Hi guys!
I'm sure that my friends in xda can solve this puzzle soon!
I did every thing you think.
after flashing some coocked roms (last of them was dexter the dark one) I decided to flash an original,official rom - because I heared that many problems resolved in it - and it was the 3.14.405.2 version that I found direct download link here! I extracted the .nbh file and renamed it to leoimg.nbh and coppied it into my FAT32 formatted sandisk SD 8GB class2 ram and I held voldown btn and pressed pwr to enter rainbow screen, flashing started but it froze at 10 or 15 % . after this I tested many ways from xda and other helpers but my phone showed these screens:
if I just power it on:
grey danger triangle
Software update failed.
Please try again.
and if i hold voldown and press pwr:
in rainbow screen:
RUUNBH
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
Upgrade ROM code error
Please try again
and if I try to flash any ROMs(in this case 3.14.405.2 official rom)
1)with usb cable : continues to 1% and show in pc:
ERROR [262] : UPDATE ERROR
The ROM Update Utility has encountered communications error during the update process. The program will guiade you step-bye-step to recover from the errors so you can continue with the update.
"I DID RECOVERY IT WASN'T SUITABLE"
2)with SD card : whether I use rainbow screen or just pwr on my device , it
automatically start flashing and at the start it shows Loading... and in some cases it froze at this level and in other cases it shows this error:
00028002
not allow
And now my spl is 3.03 so HSPL can't do anything!(as I tested it)
tnx for your replies!!!
excuesme because of very low quality pics!
EDITED:
I did task29 too,
my phone couldn't do task29 and it froze at the beginning of the operation
it did not any changes;
mmsoftonline said:
Hi guys!
I'm sure that my friends in xda can solve this puzzle soon!
I did every thing you think.
after flashing some coocked roms (last of them was dexter the dark one) I decided to flash an original,official rom - because I heared that many problems resolved in it - and it was the 3.14.405.2 version that I found direct download link here! I extracted the .nbh file and renamed it to leoimg.nbh and coppied it into my FAT32 formatted sandisk SD 8GB class2 ram and I held voldown btn and pressed pwr to enter rainbow screen, flashing started but it froze at 10 or 15 % . after this I tested many ways from xda and other helpers but my phone showed these screens:
if I just power it on:
grey danger triangle
Software update failed.
Please try again.
and if i hold voldown and press pwr:
in rainbow screen:
RUUNBH
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
Upgrade ROM code error
Please try again
and if I try to flash any ROMs(in this case 3.14.405.2 official rom)
1)with usb cable : continues to 1% and show in pc:
ERROR [262] : UPDATE ERROR
The ROM Update Utility has encountered communications error during the update process. The program will guiade you step-bye-step to recover from the errors so you can continue with the update.
"I DID RECOVERY IT WASN'T SUITABLE"
2)with SD card : whether I use rainbow screen or just pwr on my device , it
automatically start flashing and at the start it shows Loading... and in some cases it froze at this level and in other cases it shows this error:
00028002
not allow
And now my spl is 3.03 so HSPL can't do anything!(as I tested it)
tnx for your replies!!!
excuesme because of very low quality pics!
EDITED:
I did task29 too,
my phone couldn't do task29 and it froze at the beginning of the operation
it did not any changes;
Click to expand...
Click to collapse
exactly THE SAME THING
flashing to offical wont help either