Hello!
Recently i have found qtek 9100 which has lain without the battery about 4 months.
It starts with bootloader only, where:
IPL 2.18.0001
SPL 2.18.0001
I tried to flash Love and Prodigy firmware and flashing has finished without any errors but nothing changed - its just only tricolor if powered on.
Show me the way out of this RGB field, please
Hello
I´m having the same troubles with mine ...but i fix it with hardreset..
just reset with pen ..push the right and left button at the same time with the Power on Button ... then release only the powerbutton .. a messagage appears .. release the right and left button on the top site... then press talk for min. 4 sec. or more (the green one) then release it ... in a short while the phone reboots (it seams to be the same like before but it will take a while.. ) with your older settings..
i hope this was helpful
kind regards
Michael
Related
I think I have done a mistake.... I tried to upgrade my S200 from 2.15... to the v4.0.0.0.5 cross ! At first I've updated it with 'Prophet_PV_Temp' and it was successful so I've been in the step 2 : 'Prophet_PDAViet_4.0.0.0.5_Cross'. I though that it was successful so I unplugged my USB.... and it was not finished !!!!! And now my S200 wouldn't start properly, and it's stucked in the second screen which I can read :
IPL 2.10.0001
SPL 2.15.0001
GSM 02.30.21
0S 4.0.0.0 and I think it should be OS 4.0.0.0.5 !!
How can I do to fix it? I don't want to put it in a trashbin... HELP HELP HEL¨P
Edit/Delete Message
baptiste said:
I think I have done a mistake.... I tried to upgrade my S200 from 2.15... to the v4.0.0.0.5 cross ! At first I've updated it with 'Prophet_PV_Temp' and it was successful so I've been in the step 2 : 'Prophet_PDAViet_4.0.0.0.5_Cross'. I though that it was successful so I unplugged my USB.... and it was not finished !!!!! And now my S200 wouldn't start properly, and it's stucked in the second screen which I can read :
IPL 2.10.0001
SPL 2.15.0001
GSM 02.30.21
0S 4.0.0.0 and I think it should be OS 4.0.0.0.5 !!
How can I do to fix it? I don't want to put it in a trashbin... HELP HELP HEL¨P
Edit/Delete Message
Click to expand...
Click to collapse
Don't panic; do a hard-reset to your phone again (holding the camera key + comm key in the side together AND stick the hole in the bottom of the phone, while keeping the 2 keys held, until you see the screen shows some words); and repeat steps 1 and 2 altogether.
Thx for your reply,
holding the camera key + comm key in the side together AND stick the hole in the bottom of the phone, while keeping the 2 keys held, until you see the screen shows some words
Click to expand...
Click to collapse
I've done it many times but it still stucked.... Have you got any ideas?
Oh dear! I seem to have managed to do this too. Unfortunately in the middle of doing step 2 of the pdamobiz upgrade, my brother managed to kick the usb lead out of my laptop, disconnecting my m600 prophet!
I have tried the above steps & hard reset, but the phone is still stuck at the boot up screen as described above. I can't sync with my laptop again in order to run the AKU2 update, coz activesync wont recognise a device attached while it's stuck at the boot screen.
Is my phone now a rather expensive paperweight/weapon with which to bludgeon my brother?
Thanks for any help - I have searched quite a bit for an answer to this issue but found nothing.
sometimes it just takes a couple tries. let it sit for a while and do it again. i know i have had to do this a couple times in the past and just now it happened with my jamin so im reflashing it a second time. it just happens.
cardingtr said:
Put it in Bootloader mode (tricolor)by press-and-holding the Camera button and reset. Then do the first step (load the WM5 NVIDrom), hard reset, and do the second step (flash with WM6 Rom of choice). Be patient it takes approx 15 mins. All these step make sure you have USB connection.
Click to expand...
Click to collapse
and it works for me... ouffff !!!
...tried to unlockit with the athena-unlocker! After Step 1 it startet to Step2 und suddenly the connection was lost!
Now the battery lamp of the Ameo is in green mode!
I can make a factory reset, but I see no bootloader mode!
Screen is black an a green light aroundthe joystick! The Connection via active sync to my pc isn't available any mory!
What do you think?
game over - any change to bring my Ameo back to life?
Edit1: ther is no MiniSd Card inside
Hi, I do not think your Ameo is lost. Some else hat the same problem, please check http://forum.xda-developers.com/showpost.php?p=1358430&postcount=35 and try the steps described there. In most cases, it is also possible to flash WM6 if your device is stuck in the bootloader.
There are two things I would like you to try:
- To make a Hardreset hold the volume slider down and press the reset button.
- To enter Bootloader press and hold the camera button and press the reset button.
Do any of these work?
If any of these two works, you should be able to flash WM6.
...you were right - thx a lot 4 the solution
stupiddog said:
There are two things I would like you to try:....
- To enter Bootloader press and hold the camera button and press the reset button.
Do any of these work?
If any of these two works, you should be able to flash WM6.
Click to expand...
Click to collapse
At last -
That (your 2nd tipp) was the solution -WM& upgrade is now running on the ameo (now at 5%)!
Thx a lot
Jackpot thx -
Kisses from Austria
Many thx!
utakurt said:
At last -
That (your 2nd tipp) was the solution -WM& upgrade is now running on the ameo (now at 5%)!
Click to expand...
Click to collapse
You're welcome, have fun with WM6 However, if you want to kill the SIM-Lock/Net-Lock on your device, you have to run the unlocker again. It seems that WM5 has some problems running the unlocker while WM6 does not.
After you successfully run the unlocker again, remember to flash your WM6 ROM again (watch the battery power, it should always be >50% before starting flashing!) so you have the newest Radio version.
If problems persist after flashing, this page in the XDA wiki might be helpful: http://wiki.xda-developers.com/inde...e Athena Unlocker - the Black Screen of Death
stupiddog said:
There are two things I would like you to try:
- To make a Hardreset hold the volume slider down and press the reset button.
- To enter Bootloader press and hold the camera button and press the reset button.
Do any of these work?
If any of these two works, you should be able to flash WM6.
Click to expand...
Click to collapse
Hi, mate
Wot if those two things does not work??
i mean
if we can not get into boot loader or hard reset
i have this ameo does not go into boot loader or does not do hardreset
only red light on the joystick
problem occured while unlocking with Olipro, completing step 1 (got stuck at the point of saving the spl file)
thank you very much in advance for your help
BR,
I tryed multiple WM6 ROMS (Crystal 4 & Fantastic B4) and still have regularly the same issue:either when device is in my pocket (multiple times in a day , device locked) or sometime when doing a USB connection to my laptop : Prophet unexpectedly power off.., no message , no bip.. just power off...
I really did not identify the root cause of this behaviour...
Any help would be very appreciated...
I'm using WM6 from the earliest ROM's till now, following the forum about them very close. I don't experienced or red about this problem before.
So, two things: have you flashed back to WM5 to make sure your problem is WM6 related? And, if you have: provide some more explicited details, anything out of the ordinairy installed? Anything that can give us a clue.
If you want help, state your problem. We cant look into your device, can we?
WM6 unexpected power off problem additional data
IPL: 2.10.0001
SPL: 2.10.0001
GSM: 2.07.20
OS: 6.0.0.255
Current ROM: Crystal4
yes I followed carrefully downgrade instructions to WM5 before flashing to any WM6.
Power settings : On battery power : "Turn Off device in note used for..." disabled
scenario 1:
Juste take the device & lock it
eventual quick push on the power button to swith off
put it a the pocket : get it back a few minutes later : powered off
scenario 2:
take the device unlocked and just make a USB connection for Active Sync : one time immediate power off , once not...
scenarion 3 (once so far)
Switch on wifi , establish connection and ...device power off...
current ROM is Crystal 4 where I then removed addons for tests.
When I keep Power off button pressed I have the warning message before powering off.
don't have the issue with WM5.
Any configuration or WM6 behaviour I missed ? No idea so far on the root cause...still searching..
any help or same issue experiences sharing very appreciated...
This is the kind of information that makes sense, thanks.
But unfortunally, I still cant explain... Ofcourse I will report if I figure it out or have some kind of brainwave. In the meanwhile perhaps somebody else recognizes this fenomena.
i'm a newbie
i'm to excite to upgrade my new 818 pro G4 WM 5 which i bought last week..i read few post regarding on how to upgrade into WM 6..then..
1stly i've tried the upgrade package,click the hardSPL,works well after that..but i'm quite lost for step 3 & 4..so i just stop there..
i noted that my SPL change into 2.G4.4PDA
then i read korand post, bout that new rom..i've tried it & it works well,my 818 pro with WM 6..
at the same time, i try to upgrade my IPL into 2.20 but after download it,my avast detect trojan in it..so i just leave it
then i read bout crystal rom..get so excite with the features & function (also the touchflo)
so i upgrade it..
now is the problem..
after i make the hard reset (camera button, comm button & on/off (soft reset button) & reset button below(next to usb/cable slot)..
i STUCK in boot screen which shows
IPL 2.15.0001
SPL 2.G4.4PDA
GSM 02.19.21
OS 6.0.0.255
it just stuck there,no led light..
i've tried upgrade rom back to normal,but no avail as my activesync cannot detect my device.
i've tried the hard reset for few time,yet nothing happen..still the same
searchin for help in wiki,yet still no solution or maybe i'm to panic
plz help me to restore it,or maybe make it alive as normal again..
Finally !!..i've made it
for overnight i searchin & lookin how to restore my device..
(not enough sleep )
this is how i do it instead doing the usually hard reset..
my device is on & the usb cable from my device connect to laptop..
yet still stuck at the boot screen..then
i press the green button (to make phone call) + comm button + soft reset (on/off button) all a the same time (those 3 button only)
then my screen turn into 3 different color..red,green or blue (i dont quite remember already hihihi)
so, i use the 'korand' rom update utility to restore it..with his wm 6 rom
waallaa..my 818 pro is alive again...with wm 6 !!
thanks to korand for his rom, or from whomever the contributer..thank a lots !!
i think i still wanna upgrade into different type of rom..
but my SPL looks different then normal SPL i've see..
SPL 2.G4.4PDA
can anyone could lead me where can i get IPL G4.zip free virus?
well, hope this post could help others who face the same problm as mine..
next time i'll be MORE carefull..
bye..
duato said:
for overnight i searchin & lookin how to restore my device..
(not enough sleep )
this is how i do it instead doing the usually hard reset..
my device is on & the usb cable from my device connect to laptop..
yet still stuck at the boot screen..then
i press the green button (to make phone call) + comm button + soft reset (on/off button) all a the same time (those 3 button only)
then my screen turn into 3 different color..red,green or blue (i dont quite remember already hihihi)
so, i use the 'korand' rom update utility to restore it..with his wm 6 rom
waallaa..my 818 pro is alive again...with wm 6 !!
thanks to korand for his rom, or from whomever the contributer..thank a lots !!
i think i still wanna upgrade into different type of rom..
but my SPL looks different then normal SPL i've see..
SPL 2.G4.4PDA
can anyone could lead me where can i get IPL G4.zip free virus?
well, hope this post could help others who face the same problm as mine..
next time i'll be MORE carefull..
bye..
Click to expand...
Click to collapse
I just have one thing to say you play with your "IPL" when you don't know what you are doing and you brick your phone for real !! and I mean you will brick it as like it wont even turn on !! don't think about playing around with IPL. your SPL is fine. it's HardSPL now. you can upgrade other roms, just read the wm6 guide , follow step by step and you will be fine.
one more time, if you like your device and you want to keep it (and use it) don't play around with it's IPL
true..totally agree with you..
well, i guess i do like this kind of tech..i'm fast learning (usually from mistakes) risk always be my companion ..
one thing i'm curious about..if i want to upgrade to any other roms, should i upgarde my IPL 1st?..just like i try to use your personal crystal rom..why didnt i make it well, even though i follow the instruction step by step?
After i using those Korand's rom..everything is fine except my battery !!
i charging it & i notice that my device is getting hot !!..
i know this is not well..so i need to upgrade into others roms which more suitable with my device..
Thanks hma4 for your concern
___________________
HTC Dopod 818 pro
yup..better dont disturb the IPL
on second thought,it wisely not to disturb the IPL as you've mention except for those a genius
bout the battery,after few reset.. it back to normal..no hot anymore
i think i better stick with this rom for awhile.. as it is nice,stable & fast..+ more xtra storage..
In general, just leave IPL and SPL alone. Most ROMs (except WM5) work regardless of IPL/SPL and it's better to avoid bricking/damage.
I try to put AP DUAL 3.0 ROM on my AMEO with sim unlock.
Probably was CID locked, and so it was impossible to install this ROM, but here what happened....
When The Firmware Flasher rebooted the device at the first step when i pressed UPGRADE BUTTON my ATHENA died... no power at all..
I think at this passage the flashing process was not started at all, infact i did not see the tre coloured bar of the bootloader... IT DIED !!
It is impossible to power on, i try to plug the AC and no orange light...i i pull of the battery and insert the AC plug the red light is OK.....
What happens ?
Is there a way to recover my NEW DEVICE ?
Thanks to all the team !!!
gab74 said:
I try to put AP DUAL 3.0 ROM on my AMEO with sim unlock.
Probably was CID locked, and so it was impossible to install this ROM, but here what happened....
When The Firmware Flasher rebooted the device at the first step when i pressed UPGRADE BUTTON my ATHENA died... no power at all..
I think at this passage the flashing process was not started at all, infact i did not see the tre coloured bar of the bootloader... IT DIED !!
It is impossible to power on, i try to plug the AC and no orange light...i i pull of the battery and insert the AC plug the red light is OK.....
What happens ?
Is there a way to recover my NEW DEVICE ?
Thanks to all the team !!!
Click to expand...
Click to collapse
So did it start step 1 at all? Did u try a soft reset on the device to see if that would boot it back up?
Try running the unlocker anyway. You might be surprised
Olipro does excellent work. [tease]Or at least he didn't disappoint in the past![/tease]
See also http://forum.xda-developers.com/showthread.php?t=357142
See if you can get to the bootloader, what happened was that you used an older version and I'm assuming you got the x7501 which almost always is bricked when used with the older version of oli unlocker. I don't understand why they can't remove or re-label that old package, what's wrong with doing it???? Maybe less people would brick their device.
i've AMEO T-MOBILE X7500
The operating system was WINDOWS MOBILE 6
I did not use oil unlocker... i only try to flash with the ROM i say before, and my AMEO stops working before starting the flashing process.
Now my athena is died: without the battery i try to connect to ac cable and the red led lights up....when i insert the battery the red led lights off, i cannot enter into the bootloader because the ameo doesnt power on at all...
Please is there any solutions to this problem ??? It is very strange that the AMEO stop working ....before starting the flash process... infact when i push the UPGRADE button of the ROM flashing program, the ameo rebooted and died before starting the flashing process > i.e before the three coloured bars of the bootloader starts...
Any help : sorry for my bad english, i'm italian......
is there a way to power on ameo without battery ???
Just try oli's unlocker!
Sorry, but do i use the unlocker even if the PDA is died ? If i plug into the PC USB no hardware is found ? Does the unlocker work ? And please : Where can i download the last version of the unlocker ( probably a stupid question...)
yes, try the unlocker anyways. Download it from the http://forum.xda-developers.com/showthread.php?t=315831
Ok but the unlocker told me : Athena must be connceted with activesync...mine is died..only red led without battery or no led with battery inserted.....so i do not understand how the unlocker could work..... What unlocker do i download ???
In fact.. i try a nothing... the unlocker works only if the athena is recognized...so only if it is power up....but mine is dead only red led without battery....no led with battery instead...
It seems impossible that a simple flashing destroy the unit !!!!
Can you enter bootloader? Hold camera button while resetting
Or hard reset? Volume down wile poking the reset hole.
no, no bootloader, no hard reset...
nothing....
OK I contact HTC the told me to send the PDA to T-MOBILE CENTER to be repaired in warranty....but i leave in italy so i cannot send the pda in england...
i sell it on ebay is someone is interested...serach HTC ATHENA XT7500 AMEO T-MOBILE on ebay.co.uk.....
OK - I just had the same problem. No life whatsoever.
Simple solution:
Remove battery.
Wait one hour.
Replace battery.
All is fine
No need to send back to HTC
hello i´m from spain and I am new to the forum and I need help urgente.creo which is the best forum in which there pdas.the same that gab74.the pda is death or die.I do not know how I can rekindle my pda.Does nothing and htc have told me the same thing, besides not covered by the warranty.Help the PDA is new.
oscmae said:
hello i´m from spain and I am new to the forum and I need help urgente.creo which is the best forum in which there pdas.the same that gab74.the pda is death or die.I do not know how I can rekindle my pda.Does nothing and htc have told me the same thing, besides not covered by the warranty.Help the PDA is new.
Click to expand...
Click to collapse
I just told you the answer in my last post! Why do you have to ask again?
Hi all,
I got the same problem & I already did as Confucious's guide but it doesn't work. Any help?
Best regard,
Try my thread, I am having similar difficulties, though I know some solutions, so maybe some of your questions will be answered.. http://forum.xda-developers.com/showthread.php?t=528258
And in summary.. try jump-starting the battery, I'm almost sure it will help