Hi there,
I upgraded to WM5 but wanted to downgrade to WM2003. But halfways the downgrade the PDA hung. The only thing I can see in the screen is Serial at the top and v1.06 at the bottom. When I put the PDA in the cradle, Serial changes into USB. When I try to install firmware from a ROM, after a while I get an Error 101: Connection Error. I think that in some way the connection cannot be esthablished between cradle (PDA) and the computer.
Trying a soft or a hard reset doesn''t seem to do anything.
Can anyone help?
MDA II
i have the same problem. it keeps on giving me a connection error. please can some one help.
the same problem with SPV M1000. anyone have the solution?
do a hard reset guyz by this method
HOLD DOWN UR POWER BUTTON+RESET (pin at bottom)..u will see 1.06 or what ever ur bootloader version is at bottom and at top u will see SERIAL..when u connect it to USB it will change to USB....and VOILA !!!
Happy Flashing
Same Problem
Did as you said and my computer doen't pick up the connection through the cradle. HELPPPPPPPP!!!!!!
prob
HERE already tried to hardreset and then trying flashing
but can't sucess
The same problem..
we are on the same trouble...
until now, there's no way to resolve this problem,
the lucky if we can connect to PC,
i think its the connector problem,
maybe using a new sync cable rather then the cradle then
the cradle was always hit or miss for me
but i still had my wallaby cradle which always worked
Rudegar said:
maybe using a new sync cable rather then the cradle then
the cradle was always hit or miss for me
but i still had my wallaby cradle which always worked
Click to expand...
Click to collapse
I have tried about 3 different cables and the cradle one.
and so tried to 3 different PC's to connect and got same error
btw, thanks...
From what I've seen so far problems can be caused by:
1. A firewall needs configuring or temporary disabling.
2. The usb connection shouldn't be through a hub but straight to the usb on the motherboard.
3. Dubious connection to the cradle.
rhilton said:
From what I've seen so far problems can be caused by:
1. A firewall needs configuring or temporary disabling.
Click to expand...
Click to collapse
my firewall is active exception activesync service
some time disable
2. The usb connection shouldn't be through a hub but straight to the usb on the motherboard.
Click to expand...
Click to collapse
i have modding motorola like e398, e1, e2, L7, v3i etc before
i never use USB-hub, i have 8 port USB straight to motherboard,
3. Dubious connection to the cradle.
Click to expand...
Click to collapse
i dont understand about this (dubious ?)
when dopod 838 friend connected to my PC it was OK, no problem,
thanks rhilton
no pc usb connect
Have checked your phone connector? it happened to me once:1 pin was out and no way to sync !!!
CENTER]ion[/CENTER]
imamlab said:
my firewall is active exception activesync service
some time disable
i have modding motorola like e398, e1, e2, L7, v3i etc before
i never use USB-hub, i have 8 port USB straight to motherboard,
i dont understand about this (dubious ?)
when dopod 838 friend connected to my PC it was OK, no problem,
thanks rhilton
Click to expand...
Click to collapse
Pls help
Have d same problem and i've tried all these but no change. Any newer ideas ?
Pls help
Have d same problem and i've tried all these but no change. Any newer ideas ?
Pls help
Have d same problem and i've tried all these but no change. Any newer ideas ?
I have a cingular wizard with WM6 TNT 1933 (Build 18533.0.7.0) w/ TouchFlo. My battery recently died (thought it was bricked for a while, then tested the battery and bought a new one). My wizard won't connect to activesync through a usb cable(I have the advanced network checked OFF), and I don't have a bluetooth adaptor on this laptop. I have wifi here. First off I want a different OS because this one is too loaded and there isn't enough free memory, a bunch of apps I don't need. Also I'm wondering if a new OS will let me connect to activesync. Is there anyway to load one onto there, or am I just F'd?
is the phone operational now?
im sure that sktools had a repair activesync option then you can flash whatever
Bluetooth
You can use bluetooth to connect with activesync
invictus09 said:
I have a cingular wizard with WM6 TNT 1933 (Build 18533.0.7.0) w/ TouchFlo. My battery recently died (thought it was bricked for a while, then tested the battery and bought a new one). My wizard won't connect to activesync through a usb cable(I have the advanced network checked OFF), and I don't have a bluetooth adaptor on this laptop. I have wifi here. First off I want a different OS because this one is too loaded and there isn't enough free memory, a bunch of apps I don't need. Also I'm wondering if a new OS will let me connect to activesync. Is there anyway to load one onto there, or am I just F'd?
Click to expand...
Click to collapse
gmendezg said:
You can use bluetooth to connect with activesync
Click to expand...
Click to collapse
However ROM flashing must be done by direct USB connection, you didn't read the question carefully.
If you start RUU and plug the USB to your computer, the RUU screen on your wizard should display USB. If this is the case, you can run RUU directly.
If that doesn't work, try it on a different computer.
what about flashing a new rom via bootloader? have u tried that?
Htc fuze (raphael)
I know this is an old thread, but it came up when I searched this problem. I didn't find a lot of info easily, so I just tried a few things.
Problem: Cannot connect to ActiveSync because phone boots into Windows 6.5 beta and is locked at the screen saying the trial is over. When connecting it to the computer, the computer detected a device but ActiveSync could not connect.
Solution: Remove battery from phone and re-insert. Turn on while holding Volume Down button to get into serial mode. When you plug the phone into the computer in this mode, it should switch to USB mode. This allowed me to run RaphaelWrapper and then repeat the Volume Down boot once complete and reconnect to load the RUU for the AT&T stock OS.
If your phone does not switch from Serial Mode to USB Mode when connecting via USB, there is most likely a problem with the phone's USB port or a more serious problem than described above.
I hope this helps someone else! =)
Hi every body I have I-mate k-jam G3 wizard can I upgrade it to windows 6 ?
Thanks 4 all people will help me......
i have upgraded to vanilla full and for 2days i could sync thru usb but yesterday my windows didnt recognise my device...
so i read and read many Threads and advices but not help...
and Even In bootloader mode i couldnt romupdate thru usb
I think my usb of device is broken device is working on her rom
need absolute help....Plz
more info
sorry any help not yet
athena is working good only(rom is vanilla) usb is not recognized by windows 2000 xp etc...
So anyway i think rom change to original htc(spl 3.5) thru sd card
I think usb is broken
any other opinion?
broken is mayne not because of rom
maybe of hardware?
Hey guys,
i have a little annoying problem with the USB cable for the HD.
since yesterday, it wont respond.
im getting thos messages:
http://img29.imageshack.us/my.php?image=capturenwk.jpg
http://img20.imageshack.us/my.php?image=capture3chj.jpg
i cant Sync between any files and that sucks..
anyone knows how to solve this problem? the USB cable only charging my device and with now sync.
IM USING WINDOWS 7.
can that be any related?
the system updated last night and since then it happened
TNX for the help..!
BTW, i tried RESET the comp, the HD, and nothing changed.
USB Device Not Recognized
was this working before? you say you are using windows 7
is that a new install and now you cant connect to your phone?
you can removing the updated drivers that was installed, this could put things right for you.
try removing activesync and do a fresh install of activesync and if that does not help remove usb drivers and re-install them with out connecting your hd.
almost every time i have had my pdas or phone not being able to connect to activesync it has been software or drive related.
hope this help and you get is sorted
hey every body i have an prophet and its cant connect on the pc using activsync 4.5 or 4.2 also 4.1?? cuz i wanna to make an upgrade but (usb not rycognized) is appear every time i connect it so i cant cuz of this problem.
any one help me plz i need help so much
HI.
When I bought my Prophet (2nd hand) it was as a sh*t....and I decided to change / upgrade the ROM. After this it was impossible to connect to activesync and.......tachan!!! it was the usb cable!!! there are some usb cables unable to connect some devices (as my bluetooth GPS) and I changed the cable....all perfect!
Maybe is this your problem. If it is not the answer maybe you can try to change the ROM and try and try....
I hope it will help you.