I've have spent most of the day searching and trying to sort this out with little luck.
I had IPL - V2.02
SPL V 1.10
Radio 1.50
So I thought I would try and upgrade.
Bad idea.
On the boot screen I have
IPL 2.02
SPL 1.20
I've tryed to install a few different ROM's but they pull up a half black half gray fuzzy screen
I don't have SPL 3.5 so I can't install a lot of them and I've tryed to install a 1.2 ROM but its not having any of it.
What am I doing wrong?
I've been working my way though a few post about this problem.
But it is going no where.
I get
244 model errors
30 and 260 connection depending on what I am trying to do
I've try, ap4 1.2, radio 1.57 & 1.58, spl 1.2 & 3.5
loads of diffrent ROM
none of it is working
I can get to the boot screen
and can see
'P(unreadable text)
IPL - v2.02
'P(unreadable text)
SPL - v1.20.Oilpro
So the orignal unlocking must have semi worked.
Please help I'm out of ideas and going round and getting know where
solution
Hi mate
read this thread
http://forum.xda-developers.com/showthread.php?t=405814
and its links
see cmonexs post no 14
If you follow the instructions(read the whole thread first)
you should be able to fix the invalid model id.
somewhere along the line you flashed the wrong spl and stuffed the id
don't worry , most people including myself have done this.
Oh and make sure you remove simand sd card and have a full battery before flashing
Thanks for the advice all sorted now
Related
My first attempt to upgrade to AP4 did not succeed unfortunately (SPL to 3.50 upgrade went OK though), my power light stayed green and the display wouldn't come on.
So I took the Athena into bootloader and re-flashed back to AP3.
All seemed fine, the "Tap the screen to set up your device" screen appeared, I set it up and let the customization program run.
Unfortunately after the automatic reset at the end of the customization program, the device returned to the "Tap the screen to set up your device" and the customization program started again...
I tried interrupting the customization by soft resetting before it started executing itself, soft resetted during customization, let customization finish again (and again), but the device seems to be in an endless loop....
Any suggestions/help?
Thanks a lot in advance!
this happen because the spl and the kernel, AKA nk.exe, do not match. not sure what to do except try the new ap3 the cmonex posted **not sure if you tried that**
try the 3.0 cmonex posted and enjoy.
solved!
Thanks irus & Pawel062 (and cmonex!), that did the trick!
Probably not a bad idea to advise anybody who needs downgrading from AP4 to AP3 to use that rom. Download it from http://htc-hackers.com/uploads/ap3newspl.zip
See cmonex' thread at http://forum.xda-developers.com/showthread.php?t=386604
***great Information!***
HEY ALL,
I WAS ALSO HAVING SOME ISSUES VERY SIMILAR TO THESE WHILE TRYING TO "DOWNGRADE" TO ANY ROM FROM AP 4.0. THIS IS GREAT INFO AS I BUILD MY OWN ROMS CONSTANTLY, SO I WAS A BIT WORRIED WHEN I COULDNT SWITCH AFTER TRYING AP 4.O, BUT THANKS TO CMONEX, IRUS, & PAWEL062, WE CAN DOWNGRADE A BIT EASIER!
THANKS AGAIN!
M E G
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
mgozamy said:
I downloaded the http://htc-hackers.com/uploads/ap3newspl.zip
can anyone tell me the steps
note i'm stuck into the bootloader
Click to expand...
Click to collapse
just flash it with normal RUU
I have this problem of the "looping" with the customizations. My problem is that I can't get the device to a state where it is "talking" to activesync and from what I see, I need that to push this ap3spl new file.
When you say "just flash it with normal RUU" can you tell me what that means please? (sorry, noob here...) I've spent hours on the forums, wiki etc and I'm a bit lost.
I'm "trying" to get AP4 w/WM6.1 onto the device.
Purchased unlocked (new) and used on AT&T for 6 months.
Went to update the radio to 1.57 and used the unlocker first. (took out SIM/SD first of course).
Got past step one and then got a black screen on reboot...
I got AP3 to load but now I get this fun looping.. Setup device, load customizations, reboot, and start over.
Sounds like this file in this thread is my fix to at least get AP3 working but not sure how to apply. Can I do it from the bootloader?
thanks in advance for putting up with me
Oh yeah:
My current state:
ATHE100
IPL - v2.02
ATHE100 MFG
SPL -v3.50 OliNex
Eureka!
Ok, I'm not a COMPLETE noob.. (close). I'm up and running. AP3 (new spl) loaded, then loaded AP4. Woo Hoo!
No GPS
Well, I guess I'm "Almost" back up and running.
Since step three never got kicked off, it looks like my GPS rom/radio never was rewritten back to the device.
Any help on how to get just the GPS portion back?
Endless loop after flashing AP4
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Johnatara said:
I have a similar problem. My Dopod U1000 was running WM6 and I upgraded to
radio version 1.58.00 no problem. After flashing AP4 I am in a cycle where my initial boot screen has black and white lines at the top and black at the bottom
Then get the Windows Mobile 6.1 screen and after automatic customizing the
PDA resets itself. I have tried to flash the AP3newspl file but it cant communicate successfully with the synced PDA. Any help?
Click to expand...
Click to collapse
get into bootloader by pressing camera+reset and check your spl
you can flash a rom from here
also read this
http://forum.xda-developers.com/showthread.php?t=429013
Thanks lakeman. I reinstalled WM6 ROM from the boot loader.
My IPL v1.00 and SPL v1.20. Olipro and Radio 1.58
I have transferred enblerapi.cab to PDA and run it each time but when I flash
AP4 ROM or AP3newspl ROM I get an endless loop and my SPL stays v1.20
I cant seem to get a flash of SPL3.5 which I suspect is the problem.
Am I missing something?
Il download non funziona.
hey, im new but have read many of the pages here. i have burnt roms to my first wiz (G3) unlocked it and everything went well. i came about a wiz (G4) last week wm5 bland rom locked and want to get wm6 on it so after my research i went to the IMEI unlock site and purchased the unlock for the g4
the unlock seemed to go well the first time but, it won't come out of boot loader mode
i ran hornet o.10 for g4 it runs and completed to 100 % and then on reboot it comes up with the boot screen again
IPL 2.21.0001
SPL 2.21
i ran the tnt 1933 rom this morning and it completed 100% but still i have a boot screen
i know im missing something the battery power is fine .
i downloaded the stock rom for cingular but it won't load it has error "(294) INVALID VENDOR"
any suggestions ...
thanks in advance for your input
Airborne_Pathogen said:
hey, im new but have read many of the pages here. i have burnt roms to my first wiz (G3) unlocked it and everything went well. i came about a wiz (G4) last week wm5 bland rom locked and want to get wm6 on it so after my research i went to the IMEI unlock site and purchased the unlock for the g4
the unlock seemed to go well the first time but, it won't come out of boot loader mode
i ran hornet o.10 for g4 it runs and completed to 100 % and then on reboot it comes up with the boot screen again
IPL 2.21.0001
SPL 2.21
i ran the tnt 1933 rom this morning and it completed 100% but still i have a boot screen
i know im missing something the battery power is fine .
i downloaded the stock rom for cingular but it won't load it has error "wrong update utility"
any suggestions ...
thanks in advance for your input
Click to expand...
Click to collapse
Are you sure SPL is 2.21 and not 2.21.0001 as IPL 2.21.0001 ?
Well,if its 2.21 only,the phone's got mixed Bootloaders (IPL/SPL),IPL 2.21.0001 are G4 and SPL 2.21 is G3,I don't know how you got it,but your phone is 'Bricked'
mmm it figures
so it appears there could be a problem with the imei program,
as i said it never came out of boot mode after the unlock
and no errors were shown ...
i could get another and replaced the main board, this one is in new condition
except for the custom bricked rom . in the future i will not play with a g4
thanks for the diagnosis, no way to flash a new spl / ipl ... i did read that if
it booted you could get it back in some chance cases .. i am curious as to how this happened (others not doing this for a hobby could brick there only phone)
step 1 - ran imei unlock
never came out of boot mode after
2- flashing the to above roms said to be G4 safe
i never look to see what the ipl / spl were before
i looked with the wizard tool but didn't save it
well you live and learn, it's good for parts now off to ebay for another crack at it ...
thanks everyone ... the best thing about this phone is everything you can do to it
with help from those who know ...
I recommend trying to flash back to original service provider ROM, then unlock again and try another. As long as you can get to bootloader (tri-color screen), there's still hope for your phone. When it's in this mode, and you plug in the USB, does it say USB at the bottom of the phone screen? If so, you are not dead yet.
Custom build wm6 roms like TNT etc... never Brick a G4 phone as no IPL/SPL is included in them,they are completely safe for G4 devices.What I can gather,it must be the wrong imei unlock code perhaps.
Well,like Myrddin Wyllt said,there's no harm in trying,so if it gets into Bootloaders,try to flash the official rom and if there's an error "wrong update utility" ,replace the RUU in the rom with this RUU and run this RUU,hope it might work.
Myrddin Wyllt said:
I recommend trying to flash back to original service provider ROM, then unlock again and try another. As long as you can get to bootloader (tri-color screen), there's still hope for your phone. When it's in this mode, and you plug in the USB, does it say USB at the bottom of the phone screen? If so, you are not dead yet.
Click to expand...
Click to collapse
yes sir i can talk to the phone from xp pro ..
USB does come up
so i can swap the RRU with the nbf file i need ...
no file name change required on the xxx.nbf file
thanks alot for the(schooling) advise ... i was going to need to brick another to make some book ends... this could save me that
stuck
Airborne_Pathogen said:
yes sir i can talk to the phone from xp pro ..
USB does come up
so i can swap the RRU with the nbf file i need ...
no file name change required on the xxx.nbf file
thanks alot for the(schooling) advise ... i was going to need to brick another to make some book ends... this could save me that
Click to expand...
Click to collapse
ok, i swapped out every RUU i could find i get errors from
read file
invalid vendor id
wrong update utility
im too new to figure this out ..can you extract a ipl / spl from an
official rom and then flash that to get the boot loader's back in sync
i found the att 8125 ipl /spl nbf when i flash, it runs to 100% reboots but no changes
anyone have a link to flashing just the ipl / spl on the g4
i am most thankful for any advise ..
try running the hardspl on phone, it might just work to revert it back to a G4 spl.
Link to HardSPL : http://forum.xda-developers.com/showthread.php?t=332320
and G4 ipl and spl here : http://forum.xda-developers.com/showthread.php?t=342744
Also I paid to the IMEI Check and I had to change the plate because the PDA died as yours. E had not returned to the money of the IMEI Check only reply to me was that it had to change of plate ..... It had the unblocked CID?
bastards
yes they won't return my money ... somehow they bricked my phone
i would use the hard /spl and not the imei those guys are assholes
I'm trying out my first-ever ROM-flashing exercise, on my ageing Hermes.
I've read the excellent tutorials by Mr Vanx and OliPro; and I'm certain I'm following them correctly.
I've checked that my phone has SPL 1.11.
I've checked that my phone is recognised on my Vista Mobile Device Centre.
But...
I can't load HardSPL.
Here's what I've tried and what happens:
a) I've tried renaming the HardSPL-V7 .ndh file as HERMIMG.ndh and then copying to my SD card's root folder; and then initiating bootloader. After 30 minutes, soft-resetting; and then checking bootloader: still SPL 1.11
b) I've tried running via RUU wrapper; and, each time, I get as far as "this is from an unknown publisher..." [I select "yes"]; and a few seconds later, my pc shows a dialogue message: "Error 260... the update utility cannot connect to your PDA/phone". Yet everything is connected as it should be.
Can a wise soul out there suggest what I need to do? Thanks in advance.
I think you first need to unlock your phone. It's too long ago when I did it to my Hermes...
http://forum.xda-developers.com/showthread.php?t=293665
Thanks for coming back so swiftly. Yes, the blimmin' obvious didn't cross my mind....
Thanks for the link as well; I'll give it a go in an hour's time and I'll update this thread with results either way. Fingers crossed it does the trick.
Pants - I spoke too soon...
The unlocking process completed successfully on the pc and also on my Hermes. As per instructions, I turned off the phone for 10 seconds, then rebooted it.
I tried running HardSPL via the RUU wrapper - but I get the same result as mentioned in point b) above.
Any other suggestions gratefullly received and I'll let you know how I get on
Ignore me - I had 1.40 OliPro bootloader and I successfully flashed a stripped-down WM6.1 ROM.
So all's well and I like this new ROM. But I've seen some gorgeous catering by you master-chefs out there - and I like your WM6.5 main courses...!
Thanks.
Mate, its better to have Hard SPL V7 on your Hermes... Try renaming the .nbh file to hermimg.nbh, NOT .ndh.... Small mistake, BIG problem...
SPL 1.40 is an older, not so safe version of Hard SPL, Its better to put V7 (2.10 oli) on...
Cheers...
ultramag69 said:
Mate, its better to have Hard SPL V7 on your Hermes... Try renaming the .nbh file to hermimg.nbh, NOT .ndh.... Small mistake, BIG problem...
SPL 1.40 is an older, not so safe version of Hard SPL, Its better to put V7 (2.10 oli) on...
Cheers...
Click to expand...
Click to collapse
Hi
Newbie so apologies whilst I get used to the site and issues.
Already have a problem with my (bought unlocked) SPV M3100 running on UK "Three" Network
The mic does not work with calls but the headset is OK.
Mic (and headset) works when Recording Notes.
(So probable Software Problem)
Soft Reset has not worked.
Just going thru great (including size !!!) site to learn to Flash, HArd SPL etc.
(Can someone post a link to HardSPL v7 !)
To come back to this thread what are the issues (bugs etc) with WM6.5 & are they fixed yet ?
I am also thinking of getting a TouchPro2 as well.
Does it come with WM6.5 installed.
If 6.1 is anyone here running both devices and can comment on speed stability of Common ROM if installed.
(I suppose limiting factor will be the Hermes/TyTn)
(My Hermes acquired mainly for use in Third World Environments (Aid Work), where it is tougher & now quite common. Touch Pro 2 used in the UK but need to Synch. Prefer a stable good looking ROM (Not too Flashy !!). Speed not that important)
Any help/Advice in Flashing ROMS much appreciated.
Also link to HardSPL v7
Many Thanks in advance
Link to Hard SPL V7, try the 1st page of this thread.....
hi i was flashing my jasjam (the usb method) and the thing stopped anyhow reading on the net i was told to unplug it and now it gets stuck at the first logo screen.
i can get up the tri colour screen and my settings are
HERM100
IPL-1.01
HERM100
SPL-1.11
now i have flashed this jasjam twice before this happend and i have been scouring the threads trying to find a way to fix this (possibly by installing the os via the sd card if thats possible?) and the only thing i have come across that looks like it may help is a post i read elsewhere on this site but cant post the link as i am a new user but i have wrote what i think would help below.
ultra mag sent this in a reply to someone else with a bricked jasjam"If you have a memory card 2Gb or less, go to the Hard SPL thread, download Hard SPL V7 and then read post 1160 on page 116. You can drop the steps using sspl.exe as you have an old version of Hard SPL on your Hermes. Once you have Hard SPL 2.10 oli and an IPL of 1.04 then use the same method to install a rom. This will NOT fix the no GSM problem, there is no fix for that...
But at least you will have a PDA..."
will this work to fix this brick or not ( i never installed Hard spl on it)
any help would be appreicated and if ultramag69 is reading this could you please help me understand what you said above?
(i have a fairly good knowledge of computers but i may need help understanding terms you guys use.)
Reply With Quote
same here
I have exactly same problem as yours. I read alot of topics on forum but i can't manage to fix my Jasjam yet. Did you fix yours?
Best regards.
same here,but nobody seems to give a dam
Ok, after 2 days of fighting, sweating, a pc hdd full with roms,tools,mtty,etc...
...i'm giving up. i am posting a help request for the first time since i am a xda user,
and that's been for almost 2 years now. i rather solve problems by doing research on the xda forums but this time i am out of energy.
i had an raphael before where the hacking process was pretty straightforward
and flashing a cooked rom was really idiotproof.
now i got an cool athena in my hands. i was like yeah, let's flash baby....and
the original OS didn't even last for half of a day. quick enough i realised that
this baby shouldn't be flashed the raphael way - the sd card method...
ok let's get on topic:
what i did:
flashed with the AP4 SPL 3.5 AthenaUpdater (following the howto exactly)
and well. that worked fine. the OS was booting and everything. but to my
surprise it looked like that AP4 update flash thing didn't ship another cooked
rom, but flashed my SPL only. i rather expected a SPL, CID unlock and ROM
install in one single package. i don't know what made me think that, since the
raphael has to be flashed with different stuff too before beeing able to...bla
since i was so happy to find that AP4 update howto i guess i was assuming
that this is the whole deal since it doesn't say anything about seperate CID
unlocking in that .pdf
anyway, i looked for a cooked spl 3.5 compatible rom and there i found it:
[ROM] *Updated Mar/4/2010* AGB V3.00.0 (WM6.5.5 build 23534)
and well, that was basically it. the flash went ok, but after booting only
the rom's splash screen appears and nothing further happens. hard reset
doesn't help.
i tried a few other roms after that, and again. only the rom-specific custom
flash image appears and nothing happens.
tried to flash the AP3 for SPL 3.5 ROM - same thing: flash screen says "operating system is loading", which is an bitmap picture i guess...
downgrade to SPL 1.2 doesn't seem possible since this requires a running
WM, which i don't have.
bootloader works by the way, hard reset works too, but no fix...
after a little reading i get the idea that i should have cid unlocked the device
before flashing with a cooked rom? or did i something else wrong?
any help would be appreciated
oh yeah, and mtty:
the recover from invalid id procedure doesn't fix the issue.
and:
set 14 0
task 8
doesn't fix anything too, just boots the device into the never ending flash screen....
quick questions
what does your boot screen say
and did you remove your sd and simcard before flashing
yeah, the i ofcourse removed the sd card and sim card before everything.
i am at work now but afaik my bootloader screen says:
ATHE100
IPL 2.02
SPL 3.50.Olipro
before the attempt with mtty it said
ATHE400
IPL 2.02
SPL 3.50.Olipro
something like that. is that helpful?
i'm wondering that almost nobody replies. is the athena projcet kinda dead
or am i just asking BS, i don't know. anyway, i'll keep this one posted.
i have a new status of my athena: it boots a ROM for the first time. i have flashed
it with a test rom, called:
Windows Mobile 6.1 Base ROM (Testing)
It can be found on the athena latest ROM links page.
And ofcourse there is a BUT(T)....
BUT..the configuration wizard keeps looping. Means the device boots WM6.1,
asks me to calibrate the screen. after that touchflo (or sense) shows up for a few seconds, a progress bar appears and installs some (invisible) stuff and the device reboots. Normal behaviour you'd say, but the calibration screen comes again, and the progress bar too, and reboots, and again, and again...
maybe somebody could tell me how to stop that process? it seems like the
device doesn't save the first time setup settings. how to fix it?
ultrasonyk said:
i'm wondering that almost nobody replies. is the athena projcet kinda dead
or am i just asking BS, i don't know. anyway, i'll keep this one posted.
i have a new status of my athena: it boots a ROM for the first time. i have flashed
it with a test rom, called:
Windows Mobile 6.1 Base ROM (Testing)
It can be found on the athena latest ROM links page.
And ofcourse there is a BUT(T)....
BUT..the configuration wizard keeps looping. Means the device boots WM6.1,
asks me to calibrate the screen. after that touchflo (or sense) shows up for a few seconds, a progress bar appears and installs some (invisible) stuff and the device reboots. Normal behaviour you'd say, but the calibration screen comes again, and the progress bar too, and reboots, and again, and again...
maybe somebody could tell me how to stop that process? it seems like the
device doesn't save the first time setup settings. how to fix it?
Click to expand...
Click to collapse
Hi mate
I live in a different time zone and my daily email about updates to posts comes late in my day and probably when you sleep.
There are not many people who use this device and it is really a legacy machine.
However your post gives a clue to what happened.
with the bootscreen showing athe400 initially are you sure you have an x7500/x7501 or is it the x7510?
Just make sure before you follow the solution in this thread
http://forum.xda-developers.com/showthread.php?t=387596&highlight=endless+loop
the roms are very different
Check out exactly which hardware you have
this thread is from the x7510 thread and may be worth a read if you have the x7510
Additionally cmonex has the knowlege to fix your issuues if the above doesn,t work
http://forum.xda-developers.com/showthread.php?t=441684
thank god, somebody replied with useful information
well, i must be honest i didn't pay too much attention on the model number.
after reading your post, i checked and i see that i have a X7510 advantage device.
which means as far as i can understand it:
i SHOULD have the modelid ATHE400?
which means, i messed it up by flashing it with mtty to modelID ATHE100?
which means, all the time i was installing X7500 stuff on the wrong device
and bricked it that way?
so the AP4 3.5 SPL solution is not for X7510?
which means, the AP4 3.5 SPL is a hard SPL but for another device?
and after all, what do you suggest? do i need to revert my modelID
to ATHE400 and if yes, how? and after that i should follow the 2nd
thread to install a proper hardSPL and a WM6.5 ROM of my choice?
try contacting cmonex
the author of this thread
http://forum.xda-developers.com/showthread.php?t=441684
wrote the script you used to change the device id and may have a way to reverse this
good luck
lakeman, my friend!
you pointed me to the right direction. i followed the steps for installing
hardspl for x7510 from cmonex, and yeah, the modelid changed back
to athe400 and the device was booting! seems like that hardspl also
corrects the modelid automatically.
i am still curious why the device was working after flashing with AP4 3.5 SPL
in first place, since that one is actually for X7500 devices.
i should 've read some more before going to flash that thing, i must admit.
many thanks to you lakeman, and big ups for that cmonex guy!
now it's time to look for a nice wm6.5 rom for my ATHE400
fantastic
happy to help