Hi Everybody I have an Imate jamin.. and i installed wm6.5.. everything was goin good..but lately the mic become very low so when i call any body it is Difficult to hear me i flash it again and again and downgrade to WM 6.1 then WM 5 then Back to 6.5 and nothing Happens any suggestion PLz
Hey there,
Dissassemble the phone and you'll see a rubber coating on the mainboard which just covers the mic. Clean it and try again.
Related
hi guys!i bought a qtek 2020 or i don t know what is it....o2 xdaII i tried to read about them! so problem is that...i don t have the connectors u know where u plug the charger so i bought an universal chargher...but every time i wanted to charge the baterry i had to pull it out...so after some time...my phone doesn t start i don't know why i also have a problem with the touch screen!every time i had to start the phone i had to calibrate..and in te top left corner...there was something on the screen i don t know what it is...at the begining the touch screen worked every time...but then i couldn t calibrate the screen anymore because...in the top left corner didn t work!
P.S. sorry about my english i hope u understand i am from romania....i wait advices from u ..pls help me ...by the way tomorrow..i will put photos with my phone
many himalayas suffer from hardreset at batt change so i'd sugest getting one of these
http://www.expansys.hu/p.aspx?i=147225
about the screen then you may need to buy a new touchsurface for the device it can be removed and changed without changing the whole lcd
thnx
thanks for the adivices i will post some pictures..so i can't use the craddle because i don t have the connector from the bottom of the phone
http://wiki.xda-developers.com/index.php?pagename=HimalayaHardwareOverview
http://wiki.xda-developers.com/index.php?pagename=HimalayaHardware
think your best bet is to find out the part name / nr of the connector and buy a new one
http://rswww.com/
if you ruin your touchscreen with having to calib it everytime you charge you batt it would be much more expensive
i need urgent help please my spv m3100 aka htc hermes was getting white screen few times the problem got worst and now it's booting up on white screen and i have open it to see the fault and i think is the dpad cause when i press a surface mount chip on the d-pad somethines the screen comes normal where i can found that dpad pcb i think i saw one on cnn.cn but it different to my d-pad can any one help me out please ! thanks
If I understand correctly you want to buy a new keypad..
cnn seemed to have both types.. look under 8252 section for one and tytn section for the other.. is that what you are after?
On my UK M3100 I'd need this one for example: http://cnn.cn/shop/cingular-8525htc-hermes-outside-keypad-p-1610.html
i need the pcb for keypad sometime called keypad membrane too
Does this keypad mebrane fit to my orange Spv m3100 Aka hermes please ??
http://cnn.cn/shop/tytnsoftbank-x01ht-front-keyboard-p-1553.html
white screen
did you solve the white screen with a new keypad? my spv3100 bugs me very often and I cant do nothing.
hi guys,
quick question.
ive just replaced my dopod838pro housing and upon completion, WM6 wont auto-rotate. where have i gone wrong?? is it something to do with the little square of yellow plastic???
please help
thanks,
Drooch
also
the screen backlight sensor wont work either.
ive done a hard-reset, changed the yellow plastic to the original plastic from the OEM housing. all the connections are firmly connected and i am still suffering from
- no auto-rotate when sliding device
- keyboard backlight wont activate
please help as i dont want to send it 1500Km to get it fixed (outside of warrenty as well!)
Drooch
Did u solve your problem? I have the same problem with you
Solution
I recently ran into the same problem swapping to a new housing. As it turns out the housing I bought did not come with the magnet needed for the phone to recognize that the keyboard had been slid out. Just take the magnet from the old housing and attach it to the new housing. See the below link for pictures.
http://forum.xda-developers.com/showthread.php?t=332035&highlight=magnet
drooch said:
hi guys,
quick question.
ive just replaced my dopod838pro housing and upon completion, WM6 wont auto-rotate. where have i gone wrong?? is it something to do with the little square of yellow plastic???
please help
thanks,
Drooch
Click to expand...
Click to collapse
Helo.
I have a problem.Always when i close my Qtek 8500 on extern display runs camera and next second windows media player.I have tryed to instal wm6 and thinked that will lose my problem, but still hapends the same problem.I don't know, what can i do?Can it be a HW problem?
I would like to try flash the BinFS like by qtek 8310 to cleen the boot sector, but i don't konw how.With the TeraTempPro dos't work it.Any idea how to do it??
And i have ones more problem.Afte I have open my qtek more them one minute, and it get to display time out, always come from alone 76 keys on display..and then again camera and Win MP...
Please HELP.I don't know what to do..
Sorry for my anglish...
had that problem before... it was the physical phone though... it's the little ribbon cable/buttons inside your phone that are causing a push... I had to replace my ribbon cables from a donor phone and it fixed that issue for me...
tahnk you, I will try it...I'v got one more phone with defect display, i hope there are the cables ok taknk you...
you can also put it on button lock... that also stopped it from doing that...
till now, have I always button locked, becouse of it...but now, i have change this ribbon cable and everithing work again perfect...thank you very much
After I open hardware keyboard on my QTEK 9100 - screen does not react to touching. How could I fix this or is this normal to Wizard?
hIII
Touch screen dont work after i open keyboard
After I open hardware keyboard on my QTEK 9100 - screen does not react to touching. How could I fix this or is this normal to Wizard?
Reply With Quote.
Hey Dude U need get Ur fone checked its not normal. first u haVE TO check connection of the strip which connects the two part the cell i.e ur lcd screen and battery box part if connetion is fine that mean strip mite crack within it has to be get changed if not plug it properly.
What this dude above me is trying to say, is that the small ribbon cable that connects the screen to the rest of the phone may be damaged in some way, and you do indeed need to have your device checked out.
drawgas said:
After I open hardware keyboard on my QTEK 9100 - screen does not react to touching. How could I fix this or is this normal to Wizard?
Click to expand...
Click to collapse
Did you try a screen realignment? This usually fix most touch screen problems.
switch housing case now when i tur on phone i get on a bright white screen. any suggestion would be great
might have something to do with the flex cable. maybe it was misaligned when you installed your new housing, or may have gotten loose due to the open/close thing. sometimes, i wish that there was a software that would disable the automatic screen rotation when you slide open the keyboard - that way, i will not have to go through that alignment bit almost everyday.
drawgas said:
After I open hardware keyboard on my QTEK 9100 - screen does not react to touching. How could I fix this or is this normal to Wizard?
Click to expand...
Click to collapse
flash back to a base WM5 rom, like T-Mo 2.26 and see if that solves it. i had the same problem and this did the trick. from there i flashed back to wm6.1