I have a problem:
I flashed my hd2 from a stocked rom 1.42 dutch version, with hspl 1.42. I installed a custom rom from: HTC HD2 Laurentius WWE 21891UltimatePOWER.
it worked fine for 2 or 3 days and then it stocked, i reseted the phone and
When i turn on my HD2, i get a white screen. and it doest go away. Even after softreset (volume button down in bootloader)
When i go in to bootloader i see this screen:
Pb81100 hx-bc
Spl-1.42.hspl xe
0x05
Cotullahspl 0x30
Click to expand...
Click to collapse
When i try to instal a rom by going in to bootloader en then start in win xp the update wont start, it stocked at 0 %
Then i tried to flash a orginal romt by sd:
it stocked at 7 % and i get this screen:
_______________________RUUNBH
PB81100___HX-BC
SPL-1.42.__hspl___XD
________________0x05
CotullaHSPL______0x30
Upgrade ROM code error
Please try again
Click to expand...
Click to collapse
- Then i tried to flash a radio rom by activesync, in xp it wont start,
- i tried flashing by sd and it stocked on 98%
- I tried different to install a rom and radio rom by vista, but also no succes
- I tried task 29 (by the Attached Task29 into a single exe.) to erease all data from the phone, but in windows by activesync it wont start
i tried al the above from windows 7.
Is there anyone that can help me, please i getting very desperate.
VERY VERY IMPORTANT! Try and read 2-3 times what is written here http://forum.xda-developers.com/showthread.php?t=609477
Only afterwards proceed to the following :
First of all....try and use Windows Vista or Windows 7.
Second of all....do not try to use task 29 because its a bit more complicated and it involves some drivers and so on!
Use this little thing here http://forum.xda-developers.com/showpost.php?p=5848003&postcount=19 and after its completed....flash a proper radio something like 2.08.50.xx which you can find on Radio dedicated section here http://forum.xda-developers.com/showthread.php?t=611787
After all these....flash a custom ROM but be careful to be one suited with your radio! Which is a radio appliable for most of custom ROMS BUT be VERY careful!
Another thing.....do not flash from SD Card....Use the CustomRUU tool and flash it via ActiveSync!
Do you get any particular error message? When in bootloader mode, does "usb" show at the bttom of the screen? If so, try moving to a different usb port, preferably at the rear of the pc, or try different cable or even different pc. If still no luck, try uninstalling and then re-installing the latest version of Activesync.
The White Screen issue sounds like the incorrect radio version for the rom. I'm not familar with the details of the particular rom, but there are certain rom/radio combinations that will do that if they do not match eg running a 2.10 based rom with a x.xx.51.xx radio. The phone works intially until a reset and then hangs.
viperd said:
VERY VERY IMPORTANT! Try and read 2-3 times what is written here ......
Click to expand...
Click to collapse
Thanks for the replay
I tried, flashing by activesync. i flashed it the first time by hspl (the tread you link to) and then by activesync. But like i said, the hd2 stops at a white screen, so i tried by every possible way i could think of. Also i tried task 39 by the tool you mention, but it still does not work.
But i will correct my ts.
@clydeb1
I tryd to flash different radioroms, but if it try by activesync it wont start and by sd-flash it stocks at 98%, but i will try a different active sync
Okay,
I tried the following options:
- I installed a newest activesync and tried to instal an new rom under windows xp. The update stocked at 0% and i tried to install radio rom, with the same results
- I installed the windows mobile on windows 7, and tried the same as in windows xp, and still the same results.
Then i tried flashing every rom from the site by the sd-method (after every bad flash i formatted the sd-card with fat32)
With the sd method the phone stocked at 99% and then gives the next images:
00018003
LEOIMG.nbh - Fail
Radio_V2Fail
Update terminate
update fail
Click to expand...
Click to collapse
IS there any one how has a solution for this problem
Ok....try from the beginning!
1.Get from here http://forum.xda-developers.com/showthread.php?t=611433 HSPL2_RUN.zip (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....http://forum.xda-developers.com/show...3&postcount=19
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
viperd said:
Ok....try from the beginning!
1.Get from here (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
Click to expand...
Click to collapse
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Give the phone to someone who can get it to work??
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
korenbloem said:
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Click to expand...
Click to collapse
Thanks mate, if my suggestion doesn't work hopefully you can help him.
xmoo said:
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Click to expand...
Click to collapse
@Korenbloem,
A simple hardreset would have fixed your issue as well.
Instead of all kind of panic experiments like mtty/ flashing radios/roms from sd you could have come to me and I would have helped you.
You flashed a very old rom from the rom archive but never the less that rom is intensivily tested by me and the beta team.
I have no idea what kind of software you installed/tweaks you did or anything else but also with installing the wrong software it could cause the rom not to boot anymore.
Sorry to tell you but these 'bricking' stories are mostly caused by unexperiened users and it
making me sad to see more people are opening threads like this blaming a rom and causing a panic reaction in public destroying our work.
I realy hope you fix your device and I will try to help you but this isn't a rom issue.
Leo
Laurentius26 said:
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
Click to expand...
Click to collapse
Thanks for the adivse, but i already tried that with an orginal rom, but i will try it again, mabey there is a difference with a shipped rom.
The first thing i did was a hard reset, but that did't worked. (the phone is in this shape for 1 month now).
Second. I am not blaming you or anyone. I flashed the wrong radio rom i think (cant remember witch one) And that is my own fault. I never wanna make the suggestion that it is because of youre rom.
I took a risk by flashing my phone. and i is my responsibility.
Edit: I tried a shipping rom nld. But it gives the same error as always, only after 7%. But thanks for the advise
@ Xmoo, First of al thank you that you want to help with a sollution. But what does that mean a goldcard and what are the consequences of using it.
Laurentius26 helped me with fixing my device.
The problem was the radio. and by flashing a factory rom from t-mobile, the hspl was reset to spl 2.00. After that he flashed a orginal shipped rom (the orignal one from my device). And the rom is fixed again SPL 1.66 is now on the device.
Laurentius thanks for al the help!!!!!
HD2 bricked?
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
vanbasten88 said:
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
Click to expand...
Click to collapse
Do you have a branded Leo? If so, enter bootloader (remove battery, press volume down, insert battery), connect via usb (maybe you have to wait for driver installation), start the latest *.exe from your operator/carrier...
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
andreftx said:
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
Click to expand...
Click to collapse
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
silverwind said:
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
Click to expand...
Click to collapse
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
andreftx said:
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
Click to expand...
Click to collapse
The 1.66 ROM you posted above has radio version 2.06.51.07 with it. So have you considered trying to flash that radio version and then flash the ROM. I know if you get the ROM to flash it will flash that radio anyway. But you seem to think you flashed a wrong radio so just thinking out loud here.
Got a problem. I wanted to upgrade to new OzRom today so did normal tasks I did last 40 times.
get new rom and unpack it.
Rename image to LEOIMG.nbh and put it to root of SD card
perform mtty task 29
reboot, phone goes to bootloader then goes to normal grey screen it just says loading and that is it. It gets stuck there.
I had tried flashing via sspl, it sees the phone, screen on phone changes to black htc screen but loading bar sticks at 0%
I have HSPL 2.08 on the phone, I tried to re apply HSPL but it states error with usb connection. Can not upgrade radio from sd card or via sspl as well.
Did try previous rom that worked but it also does not want to load?
Any ideas?
Try flashing back to your original rom. Try that via sd card which should replace hspl back too your stock spl and then start the process from scratch.
mitty task 29 has a serious problem. you are not the only one. if ur hd2 is from tmobile. try T-Mobile_HD2_MR_Software_2.13.531.1. flash it just like the way you do. if doesnt work then copy it to sd card and flash it. . it'll return to its original stage.
pnjboyzz said:
mitty task 29 has a serious problem. you are not the only one. if ur hd2 is from tmobile. try T-Mobile_HD2_MR_Software_2.13.531.1. flash it just like the way you do. if doesnt work then copy it to sd card and flash it. . it'll return to its original stage.
Click to expand...
Click to collapse
It is odd that it did it now as I have not had any problems for last 8 months
Did not work!!
Update is that I managed to do the HSPL3 again over USB which I could not do before but I can not flash any roms.
Have you tried flash to ActiveSync????
Ok got it going again.
I hade my HSPL as 2.08.0000 and cotula signs all over it. Flashed again and it again went to the same one. However apparently .0000 means it is stock (no idea why stock rom did not want load). Flashed it again to HSPL2 and then upgrade to 3 fixed it.
alesscam said:
Have you tried flash to ActiveSync????
Click to expand...
Click to collapse
It would not help as I have done mtty before so no os on it.
no problem with mtty...
after mtty
you can press red botton for sofreset and press volume down for go to Bootloader
from bootloader you will see USB ,
this if your leo is connect to PC
I tried to update ROM trough SD
update did not end and Phone restarted
now when i tried to update rom stops on 1%
after that goes to bootloader screen
if the phone is powered off there is a triangle with "!"
How could repair it
butch_bs said:
I tried to update ROM trough SD
update did not end and Phone restarted
now when i tried to update rom stops on 1%
after that goes to bootloader screen
if the phone is powered off there is a triangle with "!"
How could repair it
Click to expand...
Click to collapse
Witch Rom version did you try to set?
Way did you it by SD and not over Active Sync?
What are the informations on the bootlouder screen?
Witch stock Rom did you have before?
I had arthemis v42
and wanted to get to 3.14
i put 3.14 on SD Card and started updating
but there was error.
i had message Updating ROM Code Error
after hard reset it desapear when try to uptade ROM from SD Card
give me "00028002 Not Allowed"
and apears bootscreen -> red green blue white
on red =>
HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
When try to upgrade trough sync from bootloader starts updating and on 1%
stops updating.
Tried with Task29 but stops on 19% stops and on PC says
"ERROR 270]: Update Error
The Image File Is corrupted. Please check your Update Utility"
Sir based on the information I see; I have the impression you have a branded device or a device from a otter aria than the stock rom you try to install.
In this case you need to use the GoldCard technique to install stock rom 3.14.
Take a look on how to do this on the first page of Artemis Rom; there is a step by step guide on how to install a other stock ROM version by using GoldCard.
But I don't understand way you will forced your device to instal stock ROM over SD, even when you have receeft multiple warrenties that it wassen't posible to install.
I am done. What I do? there it is:
1. Holded VolDown and started Phone to bootloader with error "Update ROM code error. Please try again."
2. Plugged USB
3. Started this
4. Windows started
5. Update to 3.14 trough PC
Well may be first time when I tried to update rom after Arthemis v42 (it needs SSPL) I am removed HSPL. I don't know is it the problem but directly installing original ROM did not help. Hope this will help someone.
No sir,
But there are some basic rules.
First of all before install stock ROM 3.14 you need to remove your HSPL version. (use HSPL2_RUN.exe and select for ex SPL 1.66)
Secondly you need to install stock ROM 3.14 over active sync (most sure procedure (especially for non users))
Note; by install stock ROM (especially with v 3.14) you need to use the one who is for your device aria/branded device. In case you take a otter version you will get Error 260.
If you have a branded device, you need to use the GoldCard technique.
I was wondering if anybody could help me. My phone is stuck in bootloader mode. it starts up in bootloader no matter what i do. I have tried task29, flashing original rom, flashing other roms, and from SD-card. the result is allways the same. What pussles me is that when i try to flash, it all looks normal, i get it up to 100%, and when it restarts it just goes right to bootloader mode. Tried to put Leoimg.nbh to Sd-card, and the bootloader glitches for a secoud saying loading, but then it goes straigth back to the bootloader again.
If anybody got any advice it would be grately appriciated.
I am using Hspl 2.08
Might there bi a chip or something that is broken?
The radio ROM might be corrupted
Try flashing a new radio ROM, it should fix your problem.
If you trying to flash android to your phone hspl 2.08 is the right one, but your need a Radio rom that support 576MB trick.
But you said that you flashed the original (Newest) rom, then you need the right spl to run 3.14ROM, it needs to be 3.03.xxxx for 3.14 and you have 2.08.xxxx
Run hspl4 choose 3.03.0000 or 3.03.Hspl and reboot.
G
kmaarud said:
I was wondering if anybody could help me. My phone is stuck in bootloader mode. it starts up in bootloader no matter what i do. I have tried task29, flashing original rom, flashing other roms, and from SD-card. the result is allways the same. What pussles me is that when i try to flash, it all looks normal, i get it up to 100%, and when it restarts it just goes right to bootloader mode. Tried to put Leoimg.nbh to Sd-card, and the bootloader glitches for a secoud saying loading, but then it goes straigth back to the bootloader again.
If anybody got any advice it would be grately appriciated.
I am using Hspl 2.08
Might there bi a chip or something that is broken?
Click to expand...
Click to collapse
The 3.03.0000 SPL or 3.03 HSPL has nothing to do with your problem I promise you.Tthe only reason you would need that SPL or HSPL version is to fool your HD2 into thinking it has the same amount of RAM as the TMOUS model of the HD2. The 3.14 ROM will still flash with the 2.08 HSPL you have.
It sounds like your volume down button might be stuck down as the volume down button has to be pressed down during boot up to get to the bootloader. So check your volume down button and see if if is stuck in the down position. If so this is your problem and I suggest flashing the stock ROM for your HD2 via SD card. This will put you back to complete stock and you will be good to send your HD2 in for warranty repair or exchange.
hello. i have been flashed android. and yesterday my sense of screen started to not work. now i wanna back to original rom and go to warranty, and i tried to flash leoimg.nbh from sd card, but i have error "software update failed" "00028002" "upgrade rom code error please try again" and etc. my spl 3.03.0000 . please help. and sorry for my bad english
and when im trying to install rom by usb it loads 1% and then phone went black and installation stops. please help me some 1
Get hspl4
Get unbranded wwe 3.14 rom
Into bootloader
Connect USB
Run hspl4 - choose 3.03.hspl
Reboot into bootloader
USB
Run the 3.14 install over USB
Reboot into bootloader
USB
Hspl4 - choose 3.03.0000
Done.
Or.......
Use the correct rom (using the wrong rom is why you're having problems)