Hi there,
I have some problems, which I cant solve using your forum.
So Im posting this.
Yesterday my Leo shut down and I couldnt turn on it. Today I've trided Hard Reset, but nothing was made. i can turn my phone on with white screen only. So i decided to reinstal ROM. I'v set up the bootloader and start installing oryginal ROM for HTC. And the installation is going to 1 % and then the phone stops instalation and turns on with white screen only.
What an I doing wrong?
looking for original firmware for your phone on htc.com, using the S / N
I have the same problem !!!
I've tried original from htc site, still the same.
If its important, when I'm installing, on the instalation Window, where should be written the current wersion of my soft, there's norlng, just empty place.
maybe I should do something like formating my htc or instal something other than ROM?
thx for help!
you could try to flash with sspl. maybe you have installed the 3.14 rom and removed the hspl.
tycz said:
I've tried original from htc site, still the same.
If its important, when I'm installing, on the instalation Window, where should be written the current wersion of my soft, there's norlng, just empty place.
maybe I should do something like formating my htc or instal something other than ROM?
thx for help!
Click to expand...
Click to collapse
1.try task 29(find on xda) and after that installing HSPL3.
2.after this flash any rom (including stock but i wouldn't recommend newest as we don't have newest hspl and you'll be stuck with, or you will have very small ram(50mb) if you keep older one)
I can't run task 29 from bootloader, the same problem as with ROM, it stops on 0%.
maybe some advices how to run task 29 on bootloader, maybe im doind sth wrong?
I think we have the same problems,
aktiv sync dont work, bootloader modus works,
cant find any solution in the forums,
i have tried flashing from pc and from sd card, no success
what about couple of hard resets on boot(hold down volume buttons) and perhaps try another computer or USB cable-if your friend has one newer etc...
i know from the times i had Omnia that RUU can have probs with computer also.
And have a look at this could help..
i tried all of your tipps but nothing works.
Hspl 2 and 3 do not work.
Here my bootloader information:
PB81100 HX-BC
SPL-1.42.HSPL XE
0x05
CotullaHSPL 0x30
Please help!
Did you update your ROM or Radio version? I read that white screen occurs due to incompatible Radio version.
Anyways, I screwed up my OS today by installing 'Gaz Touch Tools' and on reboot my phone showed some file was missing.. nothing was working.. phone wasn't responding well. couldn't even connect via activesync.. Right now installing Official ROM using MicroSD card.
Update in progress..
RADIO_V2 - OK
RCUST - OK
BOOTLOADER - OK
SPLASH1 - OK
OS -
CONFIGDATA -
EXTROM -
^ as the progress bar increases, the blank spaces change to OK
What I did - Formatted the MicroSD using FAT32, extracted the RUU_signed.nbh from the exe downloaded from HTC website and renamed it to LEOIMG.nbh and copied it on MicroSD card. Inserted card properly in device, started device by holding volume down button. Voila!
Update: Done installing, working fine!
Got the same problem with mine straight out if the box. SPL-1.42.0000
Charging light not working. Sometimes it goes in to bootloader when powering on and sometimes white screen with logo. I'm not impressed!
Related
Hello,
after a few months with my HD2 working right, yesterday my WinMo Crashed and I got difficulties to restart it. After some tries I was able to restart WinMo and the phone worked a short while. Then the same happened.
So I thought, it would be a good idea, to reflash my HD2. Therefore I used the flashaholics tool 1.1. Everything seemed to work fine, the Task 29 was finished, and afterwards Artmemis v24 was successfully flashed. All seemed well. But...
from then on when i start, my HD2 enters the bootloader and nothing else. I can do a hard-reset, Works! But restarts in Bootloader. I can do a reflash through USB and this works as usual. But on restart -> Bootloader. I can reflash it via SD. So I reflashed stock 1.66 ROM via SD card. Everythings works well -> Update Complete - UPDATE SUCCESS. But after restart? Of course... Bootloader.
If I reflash my Stock 1.66 ROM per SD, I have the official bootloader back installed. Thats ok. But I cant use HSPL 1.42 any more. Only HSPL 3 works. Then I have HSPL bootloader. But even then my HD2 always enters bootloader and does nothing more. Anything seems to work. With one exeption:
If I try to do a task 29 via flashaholics, the HD2 switches its screen to the HTC Logo, but the bar remains at 0%. And after a while my PC gives me error 262.
If I do a task 29 with mtty, then I get the following lines from mtty:
Format BINFS start
Fill RSVD information for block 497 to 530
CE start start block=530, total block=3566
TAG NOT FOUND !!! NOT CLEAR STORAGE !!!
Format BINFS end
And if I start my HD2 with the SD card in it, that contains the leoimg.nbh, then he automatically enters the menu, where I can press Voldown to cancel update or Power button to start update.
I have no way of coming to the white htc start screen. My HTC always enters the bootloader and thats it. And it is not a problem with the VolDown button.
Is this a hardware problem? Can I do something else? Has anyone an idea? Would be nice to hear some ideas...
Thanks in advance
Markus
Orsetti said:
Hello,
after a few months with my HD2 working right, yesterday my WinMo Crashed and I got difficulties to restart it. After some tries I was able to restart WinMo and the phone worked a short while. Then the same happened.
So I thought, it would be a good idea, to reflash my HD2. Therefore I used the flashaholics tool 1.1. Everything seemed to work fine, the Task 29 was finished, and afterwards Artmemis v24 was successfully flashed. All seemed well. But...
from then on when i start, my HD2 enters the bootloader and nothing else. I can do a hard-reset, Works! But restarts in Bootloader. I can do a reflash through USB and this works as usual. But on restart -> Bootloader. I can reflash it via SD. So I reflashed stock 1.66 ROM via SD card. Everythings works well -> Update Complete - UPDATE SUCCESS. But after restart? Of course... Bootloader.
If I reflash my Stock 1.66 ROM per SD, I have the official bootloader back installed. Thats ok. But I cant use HSPL 1.42 any more. Only HSPL 3 works. Then I have HSPL bootloader. But even then my HD2 always enters bootloader and does nothing more. Anything seems to work. With one exeption:
If I try to do a task 29 via flashaholics, the HD2 switches its screen to the HTC Logo, but the bar remains at 0%. And after a while my PC gives me error 262.
If I do a task 29 with mtty, then I get the following lines from mtty:
Format BINFS start
Fill RSVD information for block 497 to 530
CE start start block=530, total block=3566
TAG NOT FOUND !!! NOT CLEAR STORAGE !!!
Format BINFS end
And if I start my HD2 with the SD card in it, that contains the leoimg.nbh, then he automatically enters the menu, where I can press Voldown to cancel update or Power button to start update.
I have no way of coming to the white htc start screen. My HTC always enters the bootloader and thats it. And it is not a problem with the VolDown button.
Is this a hardware problem? Can I do something else? Has anyone an idea? Would be nice to hear some ideas...
Thanks in advance
Markus
Click to expand...
Click to collapse
from 2 day me too!!
not aways.
Help!!
Wrong radio version for the ROM you're flashing?
Was my thought too. But I can even install any radio version I want. Installation works flawless, then restart and... bootloader. Besides... if I install the 1.66 stockRom over the SD card, Bootloader, OS, RadioRom and everything else is set back to original. This always worked.. until yesterday. But thanks for your idea. Any other ideas?
The fact that the HD2 crashed a few times, before I tried to reflash it makes me wonder, if tehre was a error in the flash memory. And maybe I wasn`t able to reflash correctly, because there is an error within the memory? Can this be, what happened? Can I do a memory check on the phone?
Just a new idea...
thx
Markus
HELP
Hello,
I have got the same problem like Orsetti and agentemulder had.
Does anybody know how to solve it?
Fabian
Hello fabhoff,
in my case, the problem was indeed an error within the flashram. I sent the HD2 in and got a new one.
Greetings
Markus
fabhoff said:
Hello,
I have got the same problem like Orsetti and agentemulder had.
Does anybody know how to solve it?
Fabian
Click to expand...
Click to collapse
please help us
i got same problem..
My phone's boot loader says SPL 1.42.0000XE. I have not upgraded to any custom rom since I bought the phone in Feb this year.
I decided to do a hard reset since the screen was frozen and soft reset did no good.
Hard reset was successful, but after that it landed on white screen and would not proceed.
I read some articles and downloaded a stock rom RUU_signed_0409.nbh from one of the links. I even copied it to the 8gb sd card that came with my phone. It does say that it is formatted as FAT 32. I renamed the file as leoimg.nbh, reset the phone and pressed the vol down key.
Now it shows the boot loader screen, then says "loading..." forever.
Please help! - By the way, I could never find a WWE version of 1.42.0000 SPL link to download.
i've got the same prob right now.
~ updated my phone with HSPL3 < all went well and finished OK
Phone is rebooting and working
~ now I want to try a different ROM and while installing it via
Active Sync it's giving an USB Error or this LOADING...
When trying to put the new ROM onto the SD Card with leoimg.nbh
it starts with LOADING...
....
I can reboot via removing battery and after that the phone boots up normal.
It's also working. But i can't do any flashes anymore.
*ADD! Error MSG
My PHONE DETAILS:
OS: 5.2.23134 (23134.5.3.9)
Manila: 2.4.20161332.0
ROM: ChuckyROM WWE 30/08/2010
Radio: 2.07.50.27_2
Protocol: 15.33.50.07u
HSPL before error: L2_RUN
HSPL during error: L3_PKG
no ideas?
I have the same problem... I just wanna update with the stock rom (latest). (no customs) . When trying via the pc, i get connection error. when i try via SD i stays on Loading. is there a solution for this ? thanks in advance
thejippen said:
I have the same problem... I just wanna update with the stock rom (latest). (no customs) . When trying via the pc, i get connection error. when i try via SD i stays on Loading. is there a solution for this ? thanks in advance
Click to expand...
Click to collapse
Yes; using the right stock ROM (the one from your aria)
or using GoldCard technique.
Put the HD2 into bootloader and then connect via usb. Run the flash file. This will only work if you are using a rom that your carrier supports as you have said you don't have HSPL...
have you solved the problem?
I cant solve this problem either, i´ve been looking for information on the internet the whole day.
Yesterday, i tried to flash my htc hd2 following a tutorial, and I used HSPL3(although I dont know if it really work, because my htc still says 2.08.0000 without the hspl, can somebody clarify this for me, please?), and after that I tried MTTY(Here starts my problem) just as the tutorial says, and then my htc restart, so I tried to flash it via the MicroSD card, but it stays stuck on a white screen which says "loading...", after that I tried to turn it up without the bootloader, but it stayed stuck on the logo screen.
Could somebody please help me???
I would really appreciate it.
denni2727 said:
I cant solve this problem either, i´ve been looking for information on the internet the whole day.
Yesterday, i tried to flash my htc hd2 following a tutorial, and I used HSPL3(although I dont know if it really work, because my htc still says 2.08.0000 without the hspl, can somebody clarify this for me, please?), and after that I tried MTTY(Here starts my problem) just as the tutorial says, and then my htc restart, so I tried to flash it via the MicroSD card, but it stays stuck on a white screen which says "loading...", after that I tried to turn it up without the bootloader, but it stayed stuck on the logo screen.
Could somebody please help me???
I would really appreciate it.
Click to expand...
Click to collapse
Two things I have learn;
If you install stock ROM over SD it will remove your HSPL.
And if you see 2.08.0000 spl on your bootscreen than the installation of HSPL was unsuccessful.
OMG...!
Thanks for the reply...
Soo what do you think i can do?
denni2727 said:
OMG...!
Thanks for the reply...
Soo what do you think i can do?
Click to expand...
Click to collapse
Hi,
Did you manage to fix the issue? Is your phone a branded one? The best way to go about is to find the stock ROM for your device and then flash it using the SD card method. This will update your ROM and SLP to stock. From there, you should be able to install HSPL and any custom ROMs.
Tazeem
Hey all, I am having trouble booting anything onto my HD2 everytime i boot the phone i get stuck on the (tri colour screen) "Hardspl" i think..
I am able to install original HTC roms and custom roms via USB and Serial but after i install them and it says installation complete when the phone restarts it just gets stuck on the "Hardspl" screen again??
Any help is appreciated thanks
Here are some images to help
http://img29.imageshack.us/g/dsc0007riq.jpg/
(UPDATED)
How do i remove hspl ive tried installing an offical rom from the SD card but i still boot into this screen ????
Try this........
Power off the phone (make sure your battery is over 50%)
Turn on while holding the vol. down button.
You should be at bootloader (three colour screen)
If you have HSPL installed you should see "cotulla" and "HSPL" on the bootloader somewhere.
If youve been flashing official roms though this may have uninstalled HSPL.
I couldnt get the screenshots you linked to...
You can attach image files using the "manage attachments" button down under the text entry area.. (i think)
Id suggest trying to flash a stock/official rom just now until you get up and running.
With the phone at bootloader you should see the word "serial" at the bottom of the screen....
Connect via USB and wait for "serial" to change to "USB", this could take a few minutes.......
When you see "usb" flash the ROM from your pc......
You should make sure that you have the correct ROM for your phone, go to the HTC site and pump in your serial number.
If you still have problems after this then post back here with any error messages you might get...
Hope that helps.....
Thanks for the reply, for the link you need to add (http ://) sorry i should have mentioned that
but i just finished doing what you told be and it finished installing. it had the HTC logo on phone with loading bar as on PC screen no errors :S but im still stuck on the tri colour screen
I originally had android booted onto this mobile but the 3G was not working so i tried installing the HTC wm 6.5 rom that I downloaded from the HTC website but it would not get out of the tri colour screen after i installed it.
So i though it may have been the hardspl its self so i updated the SLP from 2.05 to the 3.03 one im currently on but it does the same thing
Hmm ok...
So the flash finished all the wasy to 100% and there were no error messages..
then the phone rebooted and went to bootloader (3 colours)...??
Restarting the phone just keeps returning you to bootloader??
Try turning off then back on while holding down both volume buttons and see what happens.
Which model of HD2 do you have and which ROM did you flash??
Yes thats correct.
When i turn the device on wile holding vol up-down i get a grey screen to
"This operation will delete all your personal data, and reset all settings to manufacturer default. press vol up to restore or press any other keys to cancel"
and im not sure what HTC HD2 i have..
Model: T8585 ?
I flashed the latest rom from the HTC website using the S/N
"RUU_Leo_S_HKCSL_WWE_3.14.831.3_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship"
Okay, get to that screen and press volume up to continue, this will perform a hard reset which is recommended after a flash, your device should then boot up, may take a few minutes as its the first time..........
ok, It finished in like less then 10sec but there was not skips did from 1% - 100% smoothly and says "Restore....Completed Press VolUp to boot"
So i pressed volume up and once again stuck on the tri colour screen
any more suggestions or is my phone dead?
Hmmm
Phones not bricked because 95% of the time if you can get to bootloader the problem can be fixed........
I have the feeling this is something obvious that Im not picking up on.
Chances are someone else will see this and point out the obvious but at the minute I cant think why it might be doing that......
You could try flashing the ROM from SD card.
Rename the file on your PC to "leoimg.nbh" and put it on a 2gb/4gb sd card, turn the phone off, put the card in, turn on and it should flash........
Like I said, i dont think your phone is dead, I think Im missing something obvious....
its weird because i can install roms, hardspl's and all that stuff it knows the phone is there and installs them but for some reason it never gets passes the hardspl stage.. on each boot.
it accually boots into the tri colour screen in a split second of turning the phone on
Its a longshot but is there any possibility that your volume down button is stuck in the pressed position.........
yeah i have installed off the SD card already. that took awhile but it says everything is ok and installsion has completed.
same problem though once i restart tri-coloured screen pops up.
Im afraid Im not sure about this one...........
I'll keep thinking and let you know if anything occurs to me.....
Im sure someone else will chip in at some point and point out the issue though.
alright no worries thanks for the help and time hopefully someone knows what the problem is.
Maybe if i uninstall the Hardspl? might totally wreck it and 100% brick my phone if it fails but I think its the only option ill have left soon
uninstalling hspl shouldnt cause any harm........
I didnt realise you had HSPL installed, I take it you instaled that after flashing the stock rom??
If you have HSPL installed......
Try to install a custom rom, ie an energy rom, just as an experiment........
dunno if youve seen the images yet conan, but unless its changed since, the OP has 3.03.0000
also, if he has magldr installed ( i didnt see it mentioned, but..) when you hard reset it takes just a few seconds, because it is only hard resetting magldr (at least thats my understanding, and would offer a reason why hard reset is so quick)
I suspect incorrect 3,14 flash, which didnt complete so its returning to bootloader,
so, OP, bootloader - hspl4 - 3.03.hspl - flash your 3.13 rom again, over usb.
ok thanks ill try that right now, also yes magldr was installed for android but i thought I got rid of it once i rebooted the offical HTC rom.
If this works im donating $20 to you right away no joke .. ive been trying to fix for 13hours straight
Australian icon said:
ok thanks ill try that right now, also yes magldr was installed for android but i thought I got rid of it once i rebooted the offical HTC rom.
Click to expand...
Click to collapse
sd card flash, right?
Step 1 of the flash is the spl gets overwritten by the one in the leoing.nbh rom (3.03.0000 in this case) and then the phone reboots, and starts to flash , , splashscreen (where magldr is), radio, rom.
BUT, the phone wont allow the flash to start because hspl is now gone, so it fails CID checks and stops, so doesn't remove magldr, radio, rom, nothing, it just stops. Further attempts at flashing fail because you teh user haven't notived the spl change, you assume the whole flash failed, and that hspl is still there.
You shouldnt be able to get that far normaly, it would fail before it even starts, on a stock spl, except that hspl was there, so the flash was allowed to begin.
Ok, so its on SPL-3.03.HSPL now then I installed the latest HTC offical rom with USB but still no go
also if it is resetting magldr how come it doesent load up like it used to after a reset
I didn't want to have to start a new thread, but I'm at a loss for what else to do. =/
I've been flashing back and forth between Android and WP7 for several months now, without any problems, but now that I need to revert the phone back to stock WinMo 6.5, it's just not working. Any ROM I flash, the phone boots into the white screen with green "HTC" logo, then shows the lettering in the bottom corner detailing ROM and Radio and whatnot, then that's it. It just sits at that screen indefinitely.
I've got a UK-spec unlocked HD2.
In the tri-colour bootloader screen it currently shows:
PB81100 HX-BC
SPL-3.03.0000 XE
MicroP(LED) 0x05
MicroP(Touch) 0x50
The ROM is the official HTC WWE ROM - RUU 3.14.405.2 with Radio 2.15.50.14.
I've tried Task29'ing my phone, flashing via USB, flashing via an 8GB FAT32 MicroSD card, and nothing seems to work, it always flashes, reboots, and then hangs at the white screen with green HTC logo and red lettering in the corner. I'm at a loss. I need the phone reverted to stock as I'm recycling it and they won't accept it with Android (obviously). =/
If I've missed something obvious, I'm really sorry - any and all help and/or scathing criticism is greatly appreciated.
Update - I just tried a custom ROM, using HSPL4 to change to SPL-2.08.HSPL, and it has the exact same problem. Flashes just fine, then hangs at the screen with the red lettering in the corner. What on earth is causing this? =/
Has anyone got any ideas? =[
Task29 only works with HSPL on your HD2.
Try to install SPL3.03 again by using HSPL4.
Have you tried to boot your HD2 without SD card inserted?
Have you tried to make a hard reset by removing the battery, waiting a few seconds, inserting the battery, pressing and holding the volume up and down buttons at the same time and pressing the power on button while holding the volume buttons?
By the way there are many threads with the same topic like yours with different solutions. Just use the search function with keywords "hd2 stuck white screen".
uli71 said:
Task29 only works with HSPL on your HD2.
Try to install SPL3.03 again by using HSPL4.
Have you tried to boot your HD2 without SD card inserted?
Have you tried to make a hard reset by removing the battery, waiting a few seconds, inserting the battery, pressing and holding the volume up and down buttons at the same time and pressing the power on button while holding the volume buttons?
By the way there are many threads with the same topic like yours with different solutions. Just use the search function with keywords "hd2 stuck white screen".
Click to expand...
Click to collapse
Yeah, I had 2.08.HSPL installed coming from my Android NAND ROM. I Task29'd the phone to clear out the NAND.
I've booted it without the SD card inserted, no difference. I've hard reset it (forgot to mention this in the original post =/) and it makes no difference.
And I've searched through the threads - there was nothing specific to my problem that I could find, hence my posting here. All the "Stuck at white screen" threads usually have had a problem with flashing the ROMs, or the radio hasn't installed, or they're stuck at the screen before the red lettering shows up in the bottom corner. =/
Everything about it suggests my phone should work - the ROM flashing never fails, the bootloader always shows that the ROM has installed correctly, and the white HTC screen confirms that ROM/Radio etc. have all been flashed. It just stays at the white screen with green HTC logo and the red lettering, it never moves beyond there. I've tried two stock ROMs, and a custom ROM. All have installed, all have frozen at the same point, the screen with the radio and ROM information in red lettering. =/
Maybe it's because of the combination of (H)SPL, RADIO AND ROM???
Have you tried to install WP7 or Android again, just for testing?
Sometimes, but seldomly, it seems there are leftovers from HSPL 1.66 or 2.08 altough bootloader shows SPL2.08 or 3.03 which are causing difficulties.
Try to install and remove HSPL2.08 by using HSPL2_RUN.exe before you start flashing a new ROM. Some useres in different threads reported to solve strange behavior be doing this procedure.
Good luck.
I just flashed magldr and a NAND ROM to it, both worked flawlessly, and it's now running Android as it always has, no issues.
I'll try flashing a WinMo ROM now, and see if it accepts it. If not, I'll try HSPL2_RUN and see if that helps anything. Thanks for your help =].
uli71 said:
Maybe it's because of the combination of (H)SPL, RADIO AND ROM???
Have you tried to install WP7 or Android again, just for testing?
Sometimes, but seldomly, it seems there are leftovers from HSPL 1.66 or 2.08 altough bootloader shows SPL2.08 or 3.03 which are causing difficulties.
Try to install and remove HSPL2.08 by using HSPL2_RUN.exe before you start flashing a new ROM. Some useres in different threads reported to solve strange behavior be doing this procedure.
Good luck.
Click to expand...
Click to collapse
I tried installing and removing HSPL2.08 with HSPL2_RUN.exe. I then installed SPL1.66.0000, and flashed the WWE 1.66 ROM. It flashed fine, rebooted and... Nothing. It's still hanging at the white screen with green HTC logo and red information in the corner. I'm beyond confused as to what could be causing this. Everything about my phone is telling me the ROM has flashed. It's even charging while off, and the LED changes from orange to green when it's full. The Android NAND ROM I flashed confirmed this. *flummoxed*
That sounds really strange...
Last thing you can try:
- be sure to have SPL1.66 on your HD2 by using HSPL2_RUN.exe
- format you SD card by using SD Formatter and a card reader
- download latest STOCK ROM 3.14 again from HTC homepage by using your HD2's serial number
- extract the downloaded file by using 7-zip or something similar
- copy the ruu_signed.nbh file to your SD card by using a card reader
- rename the ruu_signed.nbh file on your SD card into LEOIMG.nbh
- remove your HD2's battery
- wait a few seconds
- insert battery and SD card
- press and hold volume down button and press power button while volume down button is pressed
- release the buttons when you HD2 is powering up
- follow the instructions given on the HD2's screen
One of my step by steps, but I believe you know how to flash ROMs with SD card method.
I just tried following your steps... nothing . Although, I did notice this time, flashing via SD card, that the update failed. It got part of the way through then stopped and changed to the black screen with the grey warning triangle. When I loaded back into the bootloader, it briefly showed "ROM upgrade error, please try again" and RUUNBH in the top corner, but it then proceeded to load the update from the sd card and install it. The update worked, I rebooted the phone, but again it stuck at the white background, with the green HTC logo and red lettering. Once again the red lettering and the bootloader are saying the flash was successful... but I've left the phone for half an hour and it doesn't progress beyond the white screen.
Is there any reason it failed, then flashed, says it's flashed, but isn't booting?
Sorry, but I have no answer to your question.
Sadly I have no further ideas how to reactivate your HD2 with WM6.
Maybe there is another guy having a solution.
Hello,
I have bought used HTC HD2, which I had to repair - classic touch problem (I haven't repaired it myself). What surprised me, after the phone returned to me, it has "T-mobile" glass, but it hasn't red "dismiss call" button... So everything says it is EU version...
I wanted to install WP7.8. The phone had HSPL 2.08 and some custom WM6.5 rom. I had done Task29 and installed Magldr 1.13 (with HD2 toolkit), then I have enabled last 24mb nand and cleared mbr sd card in magldr. Everything seemd to be fine. Then I had selected usb flasher and run DWI.exe of Pdaimatejam ROM on PC. It installed, but after "Reset Now" had appeared on the phone, it didn't reboot. :/ I have pulled out battery but phone got into bootloop. Than I have repeated tasks from Task29, now it rebooted itself but still bootloop.
So I have decided to return to WM6.5 and start again. I have downloaded that RUU: RUU_Leo_S_HTC_WWE_EastEurope_3.14.479.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship I have entered hspl, then run ruu on the computer, it installed successfully but the phone doesn't boot again (white bootscreen, and reboot) :/ . I have tried again, now error occurred during installing, luckily despite hspl error, I could install rom again, but bootloop again occurs...
What should I do now? :/ I am afraid of battery level...
After installing official RUU, HSPL has stayed, is that ok?
b.andy said:
Hello,
I have bought used HTC HD2, which I had to repair - classic touch problem (I haven't repaired it myself). What surprised me, after the phone returned to me, it has "T-mobile" glass, but it hasn't red "dismiss call" button... So everything says it is EU version...
I wanted to install WP7.8. The phone had HSPL 2.08 and some custom WM6.5 rom. I had done Task29 and installed Magldr 1.13 (with HD2 toolkit), then I have enabled last 24mb nand and cleared mbr sd card in magldr. Everything seemd to be fine. Then I had selected usb flasher and run DWI.exe of Pdaimatejam ROM on PC. It installed, but after "Reset Now" had appeared on the phone, it didn't reboot. :/ I have pulled out battery but phone got into bootloop. Than I have repeated tasks from Task29, now it rebooted itself but still bootloop.
So I have decided to return to WM6.5 and start again. I have downloaded that RUU: RUU_Leo_S_HTC_WWE_EastEurope_3.14.479.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship I have entered hspl, then run ruu on the computer, it installed successfully but the phone doesn't boot again (white bootscreen, and reboot) :/ . I have tried again, now error occurred during installing, luckily despite hspl error, I could install rom again, but bootloop again occurs...
What should I do now? :/ I am afraid of battery level...
After installing official RUU, HSPL has stayed, is that ok?
Click to expand...
Click to collapse
now i assume that you are in windows mobile,you still be able to charge while your phone off if you are in windows mobile mode.
1. How can you be sure if you're device is EU models?please re-HSPL your device with HSPL 4 and install Black LK find out how much is your ROM space,remeber that part of EU and t-mobile was almost the same.
2. Your bootloop problem could be because you've installed wrong ROM in to wrong Device OR due to MMC,to check it,after flasing windows mobile ROM try to reboot,if you got bootloop try to remove MMC than reboot (it works for me)
3.If you are trying to install Windows Phone and got the bootloop,it might be because of the MMC (class,brand,etc.) try to find more information regarding this in Windows Phone section.
Hope it helps