mi tg01 got stuck yesterday...not really stuck but i could not slide the unlock...i tried a reset...nothing...after that i tried the pin method with the sd card but after the install i got stuck at ALIGN SCREEN(could not click on the cross to align and it kept moving by itself - it was like it had a mind of its own)...and the i tried the pin method with the downloader but after the download was complete, at the align screen still got the same problem. all the rom install atempts were made with the original 6.5rom and another try with some custom roms.
can unbrick it somehow or he drew his last breath?
sattodude said:
mi tg01 got stuck yesterday...not really stuck but i could not slide the unlock...i tried a reset...nothing...after that i tried the pin method with the sd card but after the install i got stuck at ALIGN SCREEN(could not click on the cross to align and it kept moving by itself - it was like it had a mind of its own)...and the i tried the pin method with the downloader but after the download was complete, at the align screen still got the same problem. all the rom install atempts were made with the original 6.5rom and another try with some custom roms.
can unbrick it somehow or he drew his last breath?
Click to expand...
Click to collapse
For Mod.
remove post... please
Nokser, shut up if you don't have anything useable to say. And post editing won't help you since history is available.
@topic:
Check if your touch screen is okay, no 'oil stain' or something.
Anyway, you can connect your tg01 to PC when on align screen, go to \Windows\StartUp and remove welcome.lnk, then reboot, your phone won't start alignment but your screen will be totally incorrect in touch.
aeroflyluby said:
Nokser, shut the fank up if you don't have anything useable to say.
@topic:
Check if your touch screen is okay, no 'oil stain' or something.
Anyway, you can connect your tg01 to PC when on align screen, go to \Windows\StartUp and remove welcome.lnk, then reboot, your phone won't start alignment but your screen will be totally incorrect in touch.
Click to expand...
Click to collapse
And if you then run the attached .cab it will set the alignment to a very high level of sensitivity which I hope you will find better than previously experienced....
View attachment ScreenCal.cab
There is more discussion about this in the original thread....
You may find it helpful to flash to a known good ROM (see Pere's Master Table for ideas on which have what characteristics - WM6.5 Titanium, Sense UI, Mobile Shell or the several WM6.5.3 or 6.5.5 variants).
Best regards,
Kevin
Hi,
I had the same problem.
It turned out that the digitizer is broken.
I bought one from ebay ~ 7 pounds and replaced it
Now it works fine.
BR
i deleted welcome.lnk now it started, entered the orange interface but i can`t install the sensitivity cab that kevin gave me....the sensitivity on my phone is gone nuts now, can`t access the folders using the phone so i can install the cab...is there another way to install the cab without pulling my hair out in the process?))
try MyMobiler while connected via ActiveSync
Related
I have a Unit PW10B1 T-mobile stuck on the T-mobile boot screen, anyway I found out “GSM ERROR” in the boot loader, any suggestion or a way to fix it, I have a working o2 mobile, I’m not aware of the battery I could replace it from the other unit and recharge it…so pls give me feedback it’s very important to me, thank you.
If you can't access the device through active synce to try flashing the RSU, then you can do nothing except trying hard reset ... if it doesn't solve it it's better to send it to repair
Biso007 said:
If you can't access the device through active synce to try flashing the RSU, then you can do nothing except trying hard reset ... if it doesn't solve it it's better to send it to repair
Click to expand...
Click to collapse
Hello Biso, I can't access the device through the active sync, I tried Hard reset as well same problem the Unit stucks on the boot screen and the light flashes every like 5 seconds... about the repair center here in leb it's impossible there's no techis could solve this problem.. Isn't another way to do something to this unit ?
Unfort. NO, I couldn't find anyway to flash the RSU through SD ... the only option if you can pass the boot screen is to copy the RSU upgrade 4 files through SD card to the \windows\starup directory and soft rest
I'll try to get in I have nothing than just to let this unit works : :roll:
Anyone here consider to say something here for help ?
I'm still stuck thus I tried the Volume buttom to enter the today screen no luck as well ,but I noticed there's an Infrared connection btw my pc and the xda but active sync cannot connect to it, But I could send a files to the Xda like now am sending a .cab file I know it's not gonna make any diffrence but still maybe someone consider some help here.........
Someone would like to help here ?
Its not much good sending a file if you cant access and execute it on the xda, you have probably realised by now that "gsm error" is likely to be fatal to your xda. There is a person on this forum called Cgigate, he lives in Canada and can fix it, dont know the charges though so you need to ask him. I think he most likely writes direct to the chip through the address lines on the chip legs probably using a jtag interface and software.
cruisin-thru said:
Its not much good sending a file if you cant access and execute it on the xda, you have probably realised by now that "gsm error" is likely to be fatal to your xda. There is a person on this forum called Cgigate, he lives in Canada and can fix it, dont know the charges though so you need to ask him. I think he most likely writes direct to the chip through the address lines on the chip legs probably using a jtag interface and software.
Click to expand...
Click to collapse
Thank you cruisin-thru.. :roll:
If i understand it right you're able to transfer files from your PC to yiur XDA.
HAve you already tried to transfer the right RSU-File to the device and tried to start the update once again?
Stefan
LumpiStefan said:
If i understand it right you're able to transfer files from your PC to yiur XDA.
HAve you already tried to transfer the right RSU-File to the device and tried to start the update once again?
Stefan
Click to expand...
Click to collapse
Yes I could transfer any file I want to the Xda but still I can't do anything to it I can't reach it thus it's not an auto installer... Thus the screen is freezed on the T-mobile image, I tried the Volume buttom to enable the today screen still no luck as well :?
Ok.
So you think, with auto installer it could work. There has been a little how to about creatind an SD card with auto installer to start the RSU Upgrade. This would be the last posibility you can try to fix your device...
Stefan
LumpiStefan said:
Ok.
So you think, with auto installer it could work. There has been a little how to about creatind an SD card with auto installer to start the RSU Upgrade. This would be the last posibility you can try to fix your device...
Stefan
Click to expand...
Click to collapse
I had that auto installer file I copied it to an SD an prepared it to do that, anyway I hadn't tried it on that device later on I plugged it in my working XDA and the show begun by installing the RSU ON MY WORKING DEVICE :evil: I removed quickly the SD ,Installation stuck on 1% I went back to the start up folder and deleted the files :roll: lol I don't wanna tell you how much it feels it's like your seeing your baby dying infront of your eyes and you can't do anything about it,at the end It's still alive breathing, working properly :wink: beware guys of the RSU issue it's really horrible it might get ur device in the tombs..
i donwloaded something and putted it on my xda II, now it says serial and at the bottom vl.01 i can't use it it's tottaly black no hard reset works, HELP!
euh i really need uyrgent help i can't connect to theactive sync either, i just downloaded the new windows to my device clicked on something and then it went off and only black letters serial and v1.0. it's not my xda so HELP HELP HELP
don't panic...
you are in bootloader mode.
you've probably executed 'enterbl.exe', which is a part of every upgrade.
just connect your device with your pc and run normal upgrade/flash procedure.
buzz
but i can't use active sync anymyore, i unzipped the thing i downloaded and now it got 7 options to choose from but when i click it it opens a install program and in big red letters ROM IMAGE FILE NOT FOUND
it also says
the pocket pc software update cannot locate the ROM image file to update to your pocket pc. Download the correct rom update for your pocket pc and try again and i am a real noob in these thing
did you try a hard reset?
press the on/off button and the softreset button at the same time.
if that wont work
http://forum.xda-developers.com/viewtopic.php?t=18287
try putting that rom on your phone and dont forget to change the country id as described.
good luck friend!
how can i change my country when i have a blanc screen on my pda? and what of the four should i download, i don't speak english so it's double hard to understand
bram said:
how can i change my country when i have a blanc screen on my pda? and what of the four should i download, i don't speak english so it's double hard to understand
Click to expand...
Click to collapse
if you understand my english thats ok.
i completly understand german but im not so good in speaking it.
normaly we can only speak english here but we can make an exeption so you can speak german to me and i will speak english back. OK? or try the translator (www.freetranslation.com)
did you perform the hardreset?
activesync won't work aslong as serial is replaced by the word usb when in the cradle it's ok carry on with the upgrade
try another pc to upgrade!
thats happen to me too.. but...
i also try to install the downloaded items from this website (which is the new windows version 2003 SE), and soon after i start installing it, my desktop computer says "error has occure during the installation process".
:shock: i was very shocked when i see my device completely blank with a word says "USB (on the top)" and "Ver. 1.03 (on the bottom)".. i really panic beacuse my active sync doesn't worked.. but then i start to hard reset my xda then reconnect my device and try to install it several times (bercause sometimes the error message still appear..) after waiting for 5 step of installation which takes abaout 2 hours
tadaaaaaaa now i have an XDA IIs application on my phone...
So in conclusion:
1. do't be panic :wink:
2. try to hard reset ur device
3. reconnect ur device (even if the activesync won't recognized ur device)
4. Install the downloaded files..
5. wait until ur computer says "deleting extended rom" (or something like that)
6. be patient..
7. Pray to GOD..
8. and here you go you got new look for ur beloved xda.
good luck..
oh it works!!!!
there are no words for it and the landscape and the themes, it's BEAUTIFULL!! thanks alot everyone!!!!!!
Similar but not same
Hi I have a similar problem.
While updating my Himalaya device to the XDA2jojo v3.2z5 (not the first time I have installed this version) it has gone completely blackscreen.
I have tried to soft, hard reboot the device. I have also tried to initiate a reinstall with connection error failure. I have tested the batttery and it is okay. No matter what I do I cannot get the device to come back to life.
If I plug the device into the cradle or attach power I get a red light where there is normally the green flashing or orange power light.
Anyone any ideas what this could be.
I have had a similar issue where I would get a blackscreen this problem has occured a few times but I have always managed to get the device back with hard reset.
Similar but not same
Hi I have a similar problem.
While updating my Himalaya device to the XDA2jojo v3.2z5 (not the first time I have installed this version) it has gone completely blackscreen.
I have tried to soft, hard reboot the device. I have also tried to initiate a reinstall with connection error failure. I have tested the batttery and it is okay. No matter what I do I cannot get the device to come back to life.
If I plug the device into the cradle or attach power I get a red light where there is normally the green flashing or orange power light.
Anyone any ideas what this could be.
I have had a similar issue where I would get a blackscreen this problem has occured a few times but I have always managed to get the device back with hard reset.
pleeeeeaaase read/search the forum i know its fustrating when your phone apears to be dead but there are about 100000 topics about this problem and about 100000 times the solution!
greetings OMEGA_ReD
Hi All,
I've done a full search, but cannot find another thread on this - if I'm wrong then please accept my apologies!
Anyway - when I start my HD2 I get nothing - just a blank white screen. It's running stock WinMo 6.5, and nothing else.
My 1st thought - screen is borked. But no - hard reset and FlashRom screens are both fine. Tried a soft-reset, no joy. In desperation I tried a hard reset; the screen says complete - but computer says 'no'. Still the white screen of death!
To add insult to injury my micro USB port has stopped working and I have to use an external battery charger so there's no chance of being able to load a new ROM or anything.
Can anyone suggest anything?
Thanks!
the_ginger_ninja said:
so there's no chance of being able to load a new ROM or anything.
Click to expand...
Click to collapse
Well, apart from the SD card flashing method.....
Ah, didn't know about that method - how'd I miss it?!
Right - time to do some more forum searching...
I will report back!
Ta!
Hello!
Since yesterday i´ve a problem with the Streak 5.
It didn`t boot right.
Theres just after the dell logo the ,,Ant-War" screen (see in the picture).
I've tried everything.
Flashing the original Rom / recovery ,.... QDL repair-tool ,....
I hope you can help me !!!
mammut
same thing happened to me, turned out the ribbon cable of the screen didn't connect properly to the mainboard.
what worked for me was to release the cable(flipping that brown part what holds it).
whenever i had the ribbon cable properly attached and locked, it wouldn't work and i would have the same screen after the Dell logo.
only after i had unlocked the connector it would work.
mammut139 said:
Hello!
Since yesterday i´ve a problem with the Streak 5.
It didn`t boot right.
PHP:
Theres just after the dell logo the ,,Ant-War" screen (see in the picture).
I've tried everything.
Flashing the original Rom / recovery ,.... QDL repair-tool ,....
I hope you can help me !!!
mammut
Click to expand...
Click to collapse
Try a factory reset not the one in streakmode but the Dell reset
In the recovery menu it dosen´t matter what i klick
i dont came to the next point, also on update.pkg.
h
hardeware problem ?
it start up like everytime, but with this F**** screen.
i can unlock it blind and set the volume but i cant see anything
it start up like everytime, but with this F**** screen.
i can unlock it blind and set the volume but i cant see anything
in my opinion it's definitely not software related, because i had the same issue and tried everything software related(from changing roms, to QLD-repair tool with different roms, recoveries and trying to mess with fastboot).
only thing that made a difference and worked, was to flip the brown thing of the connector on the mainboard, and i had to tape the ribbon cable to the mainboard to let it stay in place.
u could also test ofcourse the screen by going into fastboot and typing *#301#, and then 03 (color). if it gives a failure (TE Fail) or hangs, it's a hardware failure.
yes when i start up fastboot theres the message TE Fail ....
what can i do ?
Flipping up the clip didn't work
EDIT: I changed the LCD a few days ago
Pass the test
mammut139 said:
yes when i start up fastboot theres the message TE Fail ....
what can i do ?
Flipping up the clip didn't work
EDIT: I changed the LCD a few days ago
Click to expand...
Click to collapse
When you ask for help tell us what has happened to start the problem not 5 post later
But im glad problem resolved
yes but it worked a few day´s with the new lcd
an at one moment the system crashes and i have my Ant-War Problem.
And the sensorkey´s are falshing.
I have a problem and hope somebody have a solution.
My S3 was updated to JB. Then i uses CF Auto Root to root it. After Odin, the phone rebooted and the Samsung S3 wording started to flicker and get disorientated from the screen. Then it went blank. I tot it freezes and removed the batt. Then i redo again. The same thing happen and i leave it there then after about 8-10s, the phone reboot and started off from the languge selection. But touchscreen died.
So i install the stock rom again thinking is FW corrupted, Problem still there. I try root with CF Root 6.4, Problem still there. I install stock ROM again. Problem still there. Now my FW is official but counter is 11. I see a problem with bring back to Samsung.
I also removed batt, remove sim and all sorts of stuff but problem still exist. Bascially stuck at the start up languge selection screen and touchscreen dead
So hopefully somebody got a solution before i take the last action of bring back to samsung. Thks
Mine too!!!
Did you use the correct version of CF root??? I accidentally flashed the wrong one because it was right next to the correct one. The exact same thing happened to me!!!!!!!!!!!! I think the touch screen controller is dead. I am going to look at the Log to see what's happening. Does yours also take a while to boot or to load recovery?!!
CryptXus said:
I have a problem and hope somebody have a solution.
My S3 was updated to JB. Then i uses CF Auto Root to root it. After Odin, the phone rebooted and the Samsung S3 wording started to flicker and get disorientated from the screen. Then it went blank. I tot it freezes and removed the batt. Then i redo again. The same thing happen and i leave it there then after about 8-10s, the phone reboot and started off from the languge selection. But touchscreen died.
So i install the stock rom again thinking is FW corrupted, Problem still there. I try root with CF Root 6.4, Problem still there. I install stock ROM again. Problem still there. Now my FW is official but counter is 11. I see a problem with bring back to Samsung.
I also removed batt, remove sim and all sorts of stuff but problem still exist. Bascially stuck at the start up languge selection screen and touchscreen dead
So hopefully somebody got a solution before i take the last action of bring back to samsung. Thks
Click to expand...
Click to collapse
Hi
I am also in the same boat, any solution for this problem ?
Best regards
Sounds like u fried ur LCD touch. Hope u have insurance.
Sent from my SCH-I535 using xda app-developers app
Odp: Touchscreen not Working after rooting
I suppose wrong version used.
Sent from my washing machine...straight from the tumbler...
Please read forum rules before posting
Questions and help issues go in Q&A
Thread moved
Thank you for your cooperation
Friendly Neighborhood Moderator
My working solution
Hi, I had the same problem and the only one solution I've tested is changing the touch driver on the touch module. All you need is a broken touch (the donor) and a lot of patience.
Step1. Disassemble the working phone.
Step2. Carefully take out the touch module (here you need a lot of patience and time). DON'T TRY to change the driver on the assembled phone because the display will be destroyed. I speak from experience.
Step3. After the module is out unplug the touch panel from the display and blend out the driver.
Step4. Now you can change the driver. NEVER try to change the driver when it is on the display.
Step5. After finished changing the driver repeat all the steps in the reverse order.
It is working 100%.
Sup
lores79 said:
Hi, I had the same problem and the only one solution I've tested is changing the touch driver on the touch module. All you need is a broken touch (the donor) and a lot of patience.
Step1. Disassemble the working phone.
Step2. Carefully take out the touch module (here you need a lot of patience and time). DON'T TRY to change the driver on the assembled phone because the display will be destroyed. I speak from experience.
Step3. After the module is out unplug the touch panel from the display and blend out the driver.
Step4. Now you can change the driver. NEVER try to change the driver when it is on the display.
Step5. After finished changing the driver repeat all the steps in the reverse order.
It is working 100%.
Click to expand...
Click to collapse
So u must pay to buy a new touch module?
Dewasatya said:
So u must pay to buy a new touch module?
Click to expand...
Click to collapse
Pay yes unless its under warranty and root voids warranty .
OP self inflicted damage nothing to do but pay and learn .
jje
Root your Device
To Reset binary counter when touch is Dead Click here
Now Flash with a Stock Rom
And CLAIM Your Warranty