Firstly Format ur memory card......
Plug the SD card into your computer. Drag the ROM's ZIP file to your SD card, and wait for it to copy.
When it's done copying, eject the SD card and put it back in your phone. Reboot into Recovery mode
Use your volume keys to navigate the menus, and your power button to select menu items.WIPE DATA AND WIPE CACHE PARTITION..... Scroll down to "Install ZIP From SD Card" and navigate to the ZIP file you just copied over. Give it time to flash the ROM
When it's done, reboot your phone.
2nd method
Firstly Format ur memory card........
Open in Recovery mode......Wipe data and Wipe Cache.....click reboot now....after phone starts it shows some error and phone may struck or u will be directed to the same problem u had i.e, rebootin several times or Strucking at start up screen....dont mind it....Now turn off the mobile by removing battery and start phone in DOWNLOAD MODE and connect ur mobile to pc via usb.......
Open Odin multi downloader v4.38........flash the rom........
NOW UR MOBILE IS ALIVE.....
NOTE: 1st method worked for mah friend long ago before my phone bricked....2nd method worked for me(self xperience ).......
this is for softbrickss
Hardbrick is unrecoverable [only service center will help by replacing whole board]
madman_amit said:
this is for softbrickss
Hardbrick is unrecoverable [only service center will help by replacing whole board]
Click to expand...
Click to collapse
oh..tanq for rep by d way can u tell me how hard brick of mobile causes...when flashing the rom only????????
pagadalachetan said:
oh..tanq for rep by d way can u tell me how hard brick of mobile causes...when flashing the rom only????????
Click to expand...
Click to collapse
many cause
1. kies going berserk
2. flashing wrong recovery ie via rom manager
3. flashing rom from other devices
4. try to network unlock
5. lazy to read guide on first post of any given thread
6. moronic and stupidity
Thanx mate
Got back my Galaxy ace...thanx dude
Its kay dude
not able to get to download mode
I bricked my ace with rom manager it doesnt goes to download mode i even tried with a usb jig but its not working... is it the jig?
I connected it before using the jig for an hour to the power socket so.. any suggestions?
Thanks
an0nym0us_ said:
many cause
1. kies going berserk
2. flashing wrong recovery ie via rom manager
3. flashing rom from other devices
4. try to network unlock
5. lazy to read guide on first post of any given thread
6. moronic and stupidity
Click to expand...
Click to collapse
Number 6 is what we are when first using the android
regards,
•ƒγяύs ργяσ™•
... any constructive sugestions in what to do.. other then stating the obvious from previous post
an0nym0us_ said:
many cause
1. kies going berserk
2. flashing wrong recovery ie via rom manager
3. flashing rom from other devices
4. try to network unlock
5. lazy to read guide on first post of any given thread
6. moronic and stupidity
Click to expand...
Click to collapse
Using wrong update-binary or flash_image binary to flash boot or recovery image.
the phone doesn't go to download mode or recovery or switchs on ... so i dont understand your previous post
Any suggestions besides ...you screwed up your phone, ... i know that
What is download mode?
How do you go there?
[practice random acts of kindness and selfless acts of love]
porlish said:
the phone doesn't go to download mode or recovery or switchs on ... So i dont understand your previous post
any suggestions besides ...you screwed up your phone, ... I know that
Click to expand...
Click to collapse
one thumb rule
you use rom manager........ Go to service center
no one can help you here
HELP
pagadalachetan said:
firstly format ur memory card......
Plug the sd card into your computer. Drag the rom's zip file to your sd card, and wait for it to copy.
When it's done copying, eject the sd card and put it back in your phone. Reboot into recovery mode
use your volume keys to navigate the menus, and your power button to select menu items.wipe data and wipe cache partition..... Scroll down to "install zip from sd card" and navigate to the zip file you just copied over. Give it time to flash the rom
when it's done, reboot your phone.
2nd method
firstly format ur memory card........
Open in recovery mode......wipe data and wipe cache.....click reboot now....after phone starts it shows some error and phone may struck or u will be directed to the same problem u had i.e, rebootin several times or strucking at start up screen....dont mind it....now turn off the mobile by removing battery and start phone in download mode and connect ur mobile to pc via usb.......
Open odin multi downloader v4.38........flash the rom........
Now ur mobile is alive.....
Note: 1st method worked for mah friend long ago before my phone bricked....2nd method worked for me(self xperience ).......:d
Click to expand...
Click to collapse
i have tried both ways but still dont work!!!
Rom manager destroys your motherboard... tell service centre kies crashed when updating an act incompetent... they should believe you
Sent from my GT-S5830 using XDA
Second option didnt work 4 me..
pagadalachetan said:
Firstly Format ur memory card......
Plug the SD card into your computer. Drag the ROM's ZIP file to your SD card, and wait for it to copy.
When it's done copying, eject the SD card and put it back in your phone. Reboot into Recovery mode
Use your volume keys to navigate the menus, and your power button to select menu items.WIPE DATA AND WIPE CACHE PARTITION..... Scroll down to "Install ZIP From SD Card" and navigate to the ZIP file you just copied over. Give it time to flash the ROM
When it's done, reboot your phone.
2nd method
Firstly Format ur memory card........
Open in Recovery mode......Wipe data and Wipe Cache.....click reboot now....after phone starts it shows some error and phone may struck or u will be directed to the same problem u had i.e, rebootin several times or Strucking at start up screen....dont mind it....Now turn off the mobile by removing battery and start phone in DOWNLOAD MODE and connect ur mobile to pc via usb.......
Open Odin multi downloader v4.38........flash the rom........
NOW UR MOBILE IS ALIVE.....
NOTE: 1st method worked for mah friend long ago before my phone bricked....2nd method worked for me(self xperience ).......
Click to expand...
Click to collapse
Hi... I have tried your second option with the rom 2.3.4 ( S5830DDKQ5_bysamsdroid ) but still I can't Switch ON, No recovery mode,No downloading mode is working... to switch ON the ph. I need to put my ph. on charging & pressing the power button. I think now I have to submit my mobile to service centre.... ..
saumil_1_1 said:
Hi... I have tried your second option with the rom 2.3.4 ( S5830DDKQ5_bysamsdroid ) but still I can't Switch ON, No recovery mode,No downloading mode is working... to switch ON the ph. I need to put my ph. on charging & pressing the power button. I think now I have to submit my mobile to service centre.... ..
Click to expand...
Click to collapse
if u flSHED with rom manager and got bricked ur device then u should go to service center
I've bricked my Galaxy Ace S5830.........I don't have a pc, I'm writing this from my friend's phone!! Please help me, I've rooted via Superuser,
I.e. installing Root.zip and rebooting, after that searching for a SUPERUSER icon! Please help...........I'm in tears!!
hitulg said:
I've bricked my Galaxy Ace S5830.........I don't have a pc, I'm writing this from my friend's phone!! Please help me, I've rooted via Superuser,
I.e. installing Root.zip and rebooting, after that searching for a SUPERUSER icon! Please help...........I'm in tears!!
Click to expand...
Click to collapse
I cant get what you got...is ur phone live or dead ?
Sent from my GT-S5830 using xda app-developers app
thnx
thnx dude
Related
Hey all
First off id like to say thanks for looking and helping
I recently updated my phone to the ICS (official) via the OTA update and i found i could NOT install 3rd party versions of software
So i rebooted into odin mode where i then installed the rom i origanaly had then it got stuck at the boot screen with the yellow triangle
So i rebooted into ODIN and re flashed to the origanal XWKF3 i origanaly used
Then i rebooted to the recovery mode then tried to install the rom (update.zip) and it errors saying E:failed to verify whole-file signiture. and E:Signiture verifacation failed, Installation FAILED
It wont no matter what i do play ball so here it is WHAT CAN I DO besides throw it against a wall verrrrrry f in g hard and hope it smashes into millions of lille bits .....
It is making me ill i tell ya
So if anyone can help it would be so appreciated and i would donate £20 to there happy funds they can buy a case or something nice with ........
EDIT:: now it wont respond to ODIN odin sees it but sticks at setting up connection then fails
Also when starting ODIN mode on the phone it says ODIN MODE , PRODUCT NAME SHG-I777 (this was one of the roms i tried) and wont change no matter what rom i try... custom binary says YES (9 counts) CURRENT BINARY: CUSTOM
cheers again
Can't you skip signature verification in CWM. also did you do a band backup before updating. Strange issue you have.
Sent from Atrix 4g Neutrino 2.5p
Hi thanks for replying
I mostly have to get to the recovery from S2 root software and i have to have an unsecure tar rom installed.....
I cant boot into CWM i can only boot into there boot recovery the only options in there are
ANDROID systerm recovery <3e>
Enter: ok key, select :vol up / vol down
reboot system now
apply update from sd card (this is where i get the signiture errors)
wipe data/factory reset
wipe cache partition
thats it
What version of the sgs2 do you have? You may have flashed a ROM for the wrong model.
Sent from my GT-I9100T using XDA
I only wish i knew i thought it was the I9100 with XWKF3 tar but i am obviosly wrong and all the kernels in XDA links dont work so cant get the uk o2 ones
Is there anyway of finding out withought having to have a working phone ie through the serial etc..
It is an unlocked phone
I have it on o2 and it is british not imported
Cheers i wish i was clued up about this
The first time i rooted it when i got it it all worked well no problems and i then flashed back to the origanal rom and it worked well got all updates and was still rooted
After ICS i see i could not install some apps i had so i flashed a new insacure rom and thats where it all began
IS IT BRICKED SHOULD I SELL IT AS FAULTY
No, as your phone still turns on.
First boot back into the recovery you have now, and factory reset and wipe the cache.
Then to revert back to stock head over to the galaxy s2 forums, then into original Android development, then head into the official firmware page, and flash one of the firmwares listed there with Odin.
Hope that helps
Sent from my GT-I9100 using XDA
I will try this right now and if it works i am going to transfer 20 pound to you sir
Thanks for the support.
This is the one you ment if so all the links are dead http://forum.xda-developers.com/showthread.php?t=1075278
thats the one i tried many timmes already
nutzrutz said:
I will try this right now and if it works i am going to transfer 20 pound to you sir
Thanks for the support.
Click to expand...
Click to collapse
Try to reflash again
Sent from my GT-S5830 using xda premium
thnx but I don't want the money, just looked like you needed some help
Sent from my GT-I9100 using XDA
carbonos1 said:
thnx but I don't want the money, just looked like you needed some help
Sent from my GT-I9100 using XDA
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1075278 Links are all dead.. is there anywere else i can find them.?
EDITs the root version that is currently on it is LINUX VERSION 2.6.35.7-I9100XWKF3-CL276555 ([email protected]) (gcc version 4.4.0 (GCC) #2 SMP PREEMPT thu jan 9 18:28:28 KST 2011
Prog used to root is S2 root
Unfortunately no, but mirror 2 on xxlpq in fact does work, I'm downloading it now
Sent from my GT-I9100 using XDA
Hello there,
Here are the steps that might help you.
1. Download ODIN from attachment.
2. Download CM9 Resurrection Edition for use with Odin from below URL.
cm-9-20120330-ODIN-galaxys2.tar.md5
3. Power off your phone.
4. Press Volume Down + Home Button + Power Button simultaneously to enter into download mode.
5. When you're in Download Mode, start the ODIN you've downloaded from attachment and connect your phone to Computer.
6. Let ODIN detect your device and select the downlaoded tar.md5 file in PDA section and click on Start button.
7. If everything is fine, ODIN will install the CM9 ROM in your phone.
8. After the process is complete, disconnect the phone and wait for it to boot.
9. After successful booting up, you may stick with that build or install the latest version of CM9 from below link.
update-cm-9-20120331-CODEWORKX-galaxys2-signed.zip
10. Just put above mediafire file in your SD Card.
11. Boot your phone in Recovery mode from your OS, Wipa data, cache, dalvik-cacke, battery stats
12. Format /system
13. Install zip file from SD card and select the downloaded file from mediafire, install it and reboot after successful installation.
14. You may optionally install GAPPS from recovery by downloading it here.
Let me know how it goes.
chiaotzu said:
Hello there,
Here are the steps that might help you.
1. Download ODIN from attachment.
2. Download CM9 Resurrection Edition for use with Odin from below URL.
cm-9-20120330-ODIN-galaxys2.tar.md5
3. Power off your phone.
4. Press Volume Down + Home Button + Power Button simultaneously to enter into download mode.
5. When you're in Download Mode, start the ODIN you've downloaded from attachment and connect your phone to Computer.
6. Let ODIN detect your device and select the downlaoded tar.md5 file in PDA section and click on Start button.
7. If everything is fine, ODIN will install the CM9 ROM in your phone.
8. After the process is complete, disconnect the phone and wait for it to boot.
9. After successful booting up, you may stick with that build or install the latest version of CM9 from below link.
update-cm-9-20120331-CODEWORKX-galaxys2-signed.zip
10. Just put above mediafire file in your SD Card.
11. Boot your phone in Recovery mode from your OS, Wipa data, cache, dalvik-cacke, battery stats
12. Format /system
13. Install zip file from SD card and select the downloaded file from mediafire, install it and reboot after successful installation.
14. You may optionally install GAPPS from recovery by downloading it here.
Let me know how it goes.
Click to expand...
Click to collapse
Thanks so much for them i got them BUT now ODIN says ADDED and when i load kenel into PDA then click start it just hangs and does not flash
IT DID PREVOIUS BUT NOW IT WONT FLASH do i add the pit file that was iincluded in the odin download i got from you as i am going to try that next
nutzrutz said:
Thanks so much for them i got them BUT now ODIN says ADDED and when i load kenel into PDA then click start it just hangs and does not flash
IT DID PREVOIUS BUT NOW IT WONT FLASH do i add the pit file that was iincluded in the odin download i got from you as i am going to try that next
Click to expand...
Click to collapse
No, don't add that PIT file. Just post the log messages from ODIN.
EDIT:
Also try following things:
1. Make sure you're in download mode and your screen shows "Downloading..." text.
2. Take out your battery for 5 minutes and put it back.
3. See if the phone charges in power off mode. If yes, make sure it's charged enough, at least 30%.
4. Can you go into Recovery mode? Try pressing Volume Up + Home Button + Power Button simultaneously to enter into recovery mode. If you're able to get into recovery mode, you can flash the update-cm-9-20120331-CODEWORKX-galaxys2-signed.zip file from there. See if that works for you.
5. Possible post a screenshot of ODIN where it's stuck.
chiaotzu said:
No, don't add that PIT file. Just post the log messages from ODIN.
EDIT:
Also try following things:
1. Make sure you're in download mode and your screen shows "Downloading..." text.
2. Take out your battery for 5 minutes and put it back.
3. See if the phone charges in power off mode. If yes, make sure it's charged enough, at least 30%.
4. Can you go into Recovery mode? Try pressing Volume Up + Home Button + Power Button simultaneously to enter into recovery mode. If you're able to get into recovery mode, you can flash the update-cm-9-20120331-CODEWORKX-galaxys2-signed.zip file from there. See if that works for you.
5. Possible post a screenshot of ODIN where it's stuck.
Click to expand...
Click to collapse
Ok phone is off battery is out for a min or 10 then i will put it back in n try odin then if still not playing fair i will do it the other way.
I take it you ment put that file on my micro sd card yes then install
when i try this before it gives me two red error lines about signiture verification
IS DOING IT NOW EDIT EDIT EDIT just waiting for flash to finish IF THIS WORKS GIVE ME A PAYPAL ACCOUNT MATE YOU DESERVE A DRINK ON ME BIG TIME
I love you
YOU MY FRIEND ARE THE GREATIST PERSON ALIVE I LOVE YOU HAHAHAHAHA (in a non gay way)
IT IS ALIVE
ALIVE I TELL YOU I OWE YOU BIIIIIIIIIIG TIME please let me transfer 20 into an paypal account i only need a email address linked to it
Please accept all my gratitude
You saved me hundreds in gettin a new phone the the galaxy note looks nice......
nutzrutz said:
YOU MY FRIEND ARE THE GREATIST PERSON ALIVE I LOVE YOU HAHAHAHAHA (in a non gay way)
IT IS ALIVE
ALIVE I TELL YOU I OWE YOU BIIIIIIIIIIG TIME please let me transfer 20 into an paypal account i only need a email address linked to it
Please accept all my gratitude
You saved me hundreds in gettin a new phone the the galaxy note looks nice......
Click to expand...
Click to collapse
Congrats man for getting the device back. I'm glad that worked out for you. Check your Inbox for the message.
---------- Post added at 07:29 PM ---------- Previous post was at 07:00 PM ----------
Thanks a lot for the donation man! More than you mentioned actually. You can always count on me for any help in future.
One more thing b4 i go
Is there a reason its not connecting to Keis now
Is it the rom etc stopping it or is it something else do you recon ?
Shows up ok in my computer but when i start keis it just continusly try to connect
If not can i transfer my contacts .spb file on the sd card and update there somehow
nutzrutz said:
Is there a reason its not connecting to Keis now
Is it the rom etc stopping it or is it something else do you recon ?
Shows up ok in my computer but when i start keis it just continusly try to connect
If not can i transfer my contacts .spb file on the sd card and update there somehow
Click to expand...
Click to collapse
Right now, you've installed CyanogenMod ROM of Ice Cream Sandwich 4.0 version of Android. It doesn't have Kies in it as it's a version from google, more clean and bloatware free. If you want, you can go back to Samsung Version to use Samsung Kies. All you need to do is to download and follow the instructions from following thread:
http://forum.xda-developers.com/showthread.php?t=1544487
Alternatively, here are instructions to import it into without Kies.
there is one way i found
1. open Kies
2. open your last saved *.spb file
3. save the file again as *. vsf manually in the file name area
4. go to were normally saved spb files ( C:\Users\ _\Documents\samsung\Kies\PIMS)
5. you will find all the contacts saved as vsf file.
6. select all contacts and copy them in a directory (ontacts)
7. connect your samsong to the pc and copy the directory (cotacts) in to the sd card
8. disconect your samsong
9. select the contact icon
10. from the left key press and select import contact from sd
job done
Click to expand...
Click to collapse
Source: http://forum.xda-developers.com/showpost.php?p=15447202&postcount=4
PS: I suggest you to save all your contacts to Google that way you don't have to backup them everytime you format your device.
Will do it the 2nd way as i am happy with the software on it now
I thought i had synced them with google but am not sure how to get them back
My phone use to be rooted but when unrooting it i accidentally deleted the systemui.apk , is there anyway to get it back without rooting it again ? i tried downloading it & moving it to system/app but everytime i try it says "cannot be moved" . Some people said to flash it but i have no idea what that means . Somebody help ! (/.\)
Frodriguez93 said:
My phone use to be rooted but when unrooting it i accidentally deleted the systemui.apk , is there anyway to get it back without rooting it again ? i tried downloading it & moving it to system/app but everytime i try it says "cannot be moved" . Some people said to flash it but i have no idea what that means . Somebody help ! (/.\)
Click to expand...
Click to collapse
If you want to write something into system partition, you need root access.
So manual "repair" needs to root your phone again first.
If you don't want to root again, you can flash the ROM again to your phone.
The ROM will overwrite some partitions, such as system, and will re-create the deleted file.
Flashing a stock ROM with Odin does not need to root your phone.
Good luck !
It_ler said:
If you want to write something into system partition, you need root access.
So manual "repair" needs to root your phone again first.
If you don't want to root again, you can flash the ROM again to your phone.
The ROM will overwrite some partitions, such as system, and will re-create the deleted file.
Flashing a stock ROM with Odin does not need to root your phone.
Good luck !
Click to expand...
Click to collapse
Thanks , im kind of new at this can u list the steps on how to flash the stock rom using odin ? remind you i dnt have a notification bar so i cant connect it to the pc that way .
Follow the step in given link and u will get stock rom Good Luck
http://androidadvices.com/update-galaxy-s2-gt-i9100-official-jellybean-412-xxlsj-firmware/2
ankur.co.in said:
Follow the step in given link and u will get stock rom Good Luck
http://androidadvices.com/update-galaxy-s2-gt-i9100-official-jellybean-412-xxlsj-firmware/2
Click to expand...
Click to collapse
That wont work because i cant drag down the notification bar to connect to usb
How you are relating this you need to flash it via odin in download mode lol
You can enter in download mode by turning off ur phone then hold 3 button simultaneously vol down + home +power button then press vol up to continue
Frodriguez93 said:
That wont work because i cant drag down the notification bar to connect to usb
Click to expand...
Click to collapse
Did you read the guide linked above your post?
Download mode in Galaxy S II GT I9100 can be entered by pressing Volume down Key, Center button, and holding both simultaneously press the Power Button after which a green robot will be shown indicating the Download Mode has been entered.
Click to expand...
Click to collapse
Megaritis said:
Did you read the guide linked above your post?
Click to expand...
Click to collapse
Yes , and it says i need to connect it to the usb but i cant drag down the notification bar to connect it to the pc
Frodriguez93 said:
Yes , and it says i need to connect it to the usb but i cant drag down the notification bar to connect it to the pc
Click to expand...
Click to collapse
Hey ma8, try to read the entire content of that link once again to understand the procedure of 'Odin' flash
its not Connect to usb, but its Connect to PC using the USB cable ma8
Sun90 said:
Hey ma8, try to read the entire content of that link once again to understand the procedure of 'Odin' flash
its not Connect to usb, but its Connect to PC using the USB cable ma8
Click to expand...
Click to collapse
oh i understand now . so it doesnt matter if it pops up on the computer while its on , correct ?
Frodriguez93 said:
oh i understand now . so it doesnt matter if it pops up on the computer while its on , correct ?
Click to expand...
Click to collapse
The process starts while the phone is OFF.
1. Turn OFF your phone.
2. Connect your mobile with your computer using USB cable.
3. While off, hold the Volume down Key, then the Home (Center) key.
4. While holding both buttons, turn on your phone.
5. The phone will boot in Download mode.
6. Press Volume up to continue in Download mode.
7. Open Odin on your computer, it should be like the first picture of the tutorial linked above.
8. Click the PDA button, select the firmware file and press Start.
9. Wait until Odin writes "All threads completed" and says PASS! on a green box on the top left.
10. Disconnect your mobile from your computer.
11. Power on your mobile, and you're done!
Hey guys. Im a noob here. just thought i'd share something is stumbled upon.
This is probably the easiest and quickest method to ROOT your Cherry Mobile Flame 2.0/ Karbonn S1 Titanium.
STEPS:
1. Download ZIP File for rooting in the attachments below
2. Connect your device to a pc and copy and paste the ZIP file you just downloaded to the external card on the device. (it really does not matter if your phone is in USB debugging mode or not.)
3. Disconnect the device from the PC safely and turn it off.
4. Hold the volume up key+ power button at the same time until a green screen appears. (this is the fastboot mode) Keep holding until screen turns red (recovery mode) and release to enter stock recovery.
5. Navigate using hardware buttons (power to confirm selections) and wipe cache partition and factory reset data.
6. select "apply update from external SD card" and navigate to where you pasted the ZIP file for rooting.
7. Confirm the ZIP file selection and wait for the process to finish.
8. Reboot the device.
THAT'S IT!!!
your phone should now be rooted. the super user app should now be visible in the app drawer of the device.
Thanks.
Kindly kit thanks if this helped you. CHEERS!
Thanks!
Thanks kabayan. :good:
kaudo9 said:
Thanks kabayan. :good:
Click to expand...
Click to collapse
You are most welcome bro. Let me know if it works on stock. I did this on my flame 2.0 that seems to have been toyed with prior to my getting it. So it could be that it wasn't stock when I tried this method.
Not bale to root
Not Able to Root Karboon Titanium S1 via this Method, Eveything happening correct as per post but no Superuser & Binary after restarting
adilamir said:
Not Able to Root Karboon Titanium S1 via this Method, Eveything happening correct as per post but no Superuser & Binary after restarting
Click to expand...
Click to collapse
Hey bro sorry about that. you will have to flash the zip file using CWM.
jansdizon said:
Hey bro sorry about that. you will have to flash the zip file using CWM.
Click to expand...
Click to collapse
Bro but from where we can install CWM for it?can you please provide link of that thread
simple way of rooting
pankmohan said:
Bro but from where we can install CWM for it?can you please provide link of that thread
Click to expand...
Click to collapse
Bro yesterday i have rooted my phone simple way for rooting is just serch flame 2.0 boot image n place it in cwm recovery n click on root me file it Will 100% work also stock rom is available if you want you can use it
karbonn s1 titanium/cherry mobile flame cloc2.0kworkmod recovery!
hey guys..i just flashed clockworkmod recovery in my karbonn s1 titanium a.k.a cherry mobile flame 2.0!
so here are the steps
1.download the file named AIO flasher from the link provided below
2.download the .img file
3.connect ur phone in fastboot mode using the usb
4.open the file named aio flasher.exe
5.select the img file
6..check the recovery mode and the erase check boxes
7.select the 'from fastboot' reboot mode in the reboot menu
8.click on flash
Finally clock work mod is been flashed in your phone
:laugh::laugh:
message me for the download link..
xda is not allowing me to post any download links
Clone Caught!!
Hey Guys
Look A Like of Karbonn S1 and Cherry Mobile Flame 2.0 is K-Touch U86
http://www.gizmochina.com/2013/02/2...phone-with-quad-core-msm8225q-1-2ghz-chipset/
rooting cherry mobile hyper
hi guys.. i need your help.. does anyone here have a knowledge of rooting cherry mobile hyper? thanks..
thanks
jansdizon said:
Hey guys. Im a noob here. just thought i'd share something is stumbled upon.
This is probably the easiest and quickest method to ROOT your Cherry Mobile Flame 2.0/ Karbonn S1 Titanium.
STEPS:
1. Download ZIP File for rooting in the attachments below
2. Connect your device to a pc and copy and paste the ZIP file you just downloaded to the external card on the device. (it really does not matter if your phone is in USB debugging mode or not.)
3. Disconnect the device from the PC safely and turn it off.
4. Hold the volume up key+ power button at the same time until a green screen appears. (this is the fastboot mode) Keep holding until screen turns red (recovery mode) and release to enter stock recovery.
5. Navigate using hardware buttons (power to confirm selections) and wipe cache partition and factory reset data.
6. select "apply update from external SD card" and navigate to where you pasted the ZIP file for rooting.
7. Confirm the ZIP file selection and wait for the process to finish.
8. Reboot the device.
THAT'S IT!!!
your phone should now be rooted. the super user app should now be visible in the app drawer of the device.
Thanks.
Kindly kit thanks if this helped you. CHEERS!
Click to expand...
Click to collapse
thank you kabayan your the man :good:
not working
sorry but this is not working for me...
Pano
jansdizon said:
Hey guys. Im a noob here. just thought i'd share something is stumbled upon.
This is probably the easiest and quickest method to ROOT your Cherry Mobile Flame 2.0/ Karbonn S1 Titanium.
STEPS:
1. Download ZIP File for rooting in the attachments below
2. Connect your device to a pc and copy and paste the ZIP file you just downloaded to the external card on the device. (it really does not matter if your phone is in USB debugging mode or not.)
3. Disconnect the device from the PC safely and turn it off.
4. Hold the volume up key+ power button at the same time until a green screen appears. (this is the fastboot mode) Keep holding until screen turns red (recovery mode) and release to enter stock recovery.
5. Navigate using hardware buttons (power to confirm selections) and wipe cache partition and factory reset data.
6. select "apply update from external SD card" and navigate to where you pasted the ZIP file for rooting.
7. Confirm the ZIP file selection and wait for the process to finish.
8. Reboot the device.
THAT'S IT!!!
your phone should now be rooted. the super user app should now be visible in the app drawer of the device.
Thanks.
Kindly kit thanks if this helped you. CHEERS!
Click to expand...
Click to collapse
Pano po ba mag root without losing Apps, Game datas, Save data, accounts login... Thanks po in advance
wifi signal and antenna signal becomes low
hi sir, after doing the how to root in my mobile cherry flame 2.0, my device wifi and antenna becomes low. need your advise.
after rooting procedure in flame 2.0
wifi, bluetooth and antenna signal becomes low (gray). CM flame 2.0
need your advise.
please help us by telling how to flash CWM on our karbonn s1
sir
please help us by telling how to flash CWM on our karbonn s1 ........and please provide us the links also of that essential stuff to do so ......because i tried alot of methoed like flashing with bin4cry methoed and flashing with aio flasher but every time i failed :crying:.......so please guide me ......please
Sir I need you Help
jansdizon said:
Hey guys. Im a noob here. just thought i'd share something is stumbled upon.
This is probably the easiest and quickest method to ROOT your Cherry Mobile Flame 2.0/ Karbonn S1 Titanium.
STEPS:
1. Download ZIP File for rooting in the attachments below
2. Connect your device to a pc and copy and paste the ZIP file you just downloaded to the external card on the device. (it really does not matter if your phone is in USB debugging mode or not.)
3. Disconnect the device from the PC safely and turn it off.
4. Hold the volume up key+ power button at the same time until a green screen appears. (this is the fastboot mode) Keep holding until screen turns red (recovery mode) and release to enter stock recovery.
5. Navigate using hardware buttons (power to confirm selections) and wipe cache partition and factory reset data.
6. select "apply update from external SD card" and navigate to where you pasted the ZIP file for rooting.
7. Confirm the ZIP file selection and wait for the process to finish.
8. Reboot the device.
THAT'S IT!!!
your phone should now be rooted. the super user app should now be visible in the app drawer of the device.
Thanks.
Kindly kit thanks if this helped you. CHEERS!
Click to expand...
Click to collapse
Sir, if this was the quickiest and easier way in rooting CM Flame 2.0, theres is no need to use flasher?? or CWM? just follow the steps your giving? coz i dont have the flasher or the CWM. Plase I nedd your response Sir. Thank you.
Any roms
Sent from my GT-I8552 using XDA Premium HD app
reset for entry qpst download
jansdizon said:
Hey guys. Im a noob here. just thought i'd share something is stumbled upon.
This is probably the easiest and quickest method to ROOT your Cherry Mobile Flame 2.0/ Karbonn S1 Titanium.
STEPS:
1. Download ZIP File for rooting in the attachments below
2. Connect your device to a pc and copy and paste the ZIP file you just downloaded to the external card on the device. (it really does not matter if your phone is in USB debugging mode or not.)
3. Disconnect the device from the PC safely and turn it off.
4. Hold the volume up key+ power button at the same time until a green screen appears. (this is the fastboot mode) Keep holding until screen turns red (recovery mode) and release to enter stock recovery.
5. Navigate using hardware buttons (power to confirm selections) and wipe cache partition and factory reset data.
6. select "apply update from external SD card" and navigate to where you pasted the ZIP file for rooting.
7. Confirm the ZIP file selection and wait for the process to finish.
8. Reboot the device.
THAT'S IT!!!
your phone should now be rooted. the super user app should now be visible in the app drawer of the device.
Thanks.
Kindly kit thanks if this helped you. CHEERS!
Click to expand...
Click to collapse
Sir do you know how to fix "reset for entry qpst download" for flame 2.0? Pls. help. Im from MAKATI
Need Help to Flash CWM
Hello All,
I have rooted my Wife's Karbonn S1 Titanium via Framaroot - Gandalf method. It was easy and 100% Rooted.
Can somebody please help with CWM Recovery Flash process with required steps and files so that I can do the needful?
Thanks in advance for your help!
I have a SGH-I717and it won't start when I put a charged battery in it it flashes the Samsung logo twice and then it goes black please help I really love this phone and really want it to work....
Most likely ur phone is in a loop mode.. Is the phone rooted?
Sent from galaxy note t879 using avatar on 4.1.2
Does it continually flash the Samsung logo? Like it's restarting it's self? If so, it could be a stuck power button. Going to need more information from you op to get any help.
As asked above, is it rooted? If so what else has been done? Please elaborate for us.
angelf82 said:
Most likely ur phone is in a loop mode.. Is the phone rooted?
Sent from galaxy note t879 using avatar on 4.1.2
Click to expand...
Click to collapse
my phone have the same problem and its rooted~! when i tried to get into recovery mode and cant access~ also when i press volume down button phone will vibrate
May be a bad flash.
All this might work but I highly suggest the latest cwm so when I mention downloading a ROM and gapps, you might want to get a zip file of the latest cwm and flash that first using Odin.
1. Pull the battery
2. Put battery back in.
3. Hold down volume up and down and power
4. Let go of power button after phone vibrates once continue to hold volume up and down.
5. Should now be in recovery
6. Wipe and format everything internal card/external card (this will get rid of everything so if you need to mount as USB and back up pictures to a PC)
7. Mount as USB storage and plug into pc
8. Download custom ROM and gapps using IE
9. Put custom ROM and gapps into external SD folder on phone
10. Safely remove device on PC, right click internal or external SD drive in my computer and select safe removal
11. Select Unmount USB on phone
12. Install ROM then gapps
13. Hope this helps.
Sent from my SAMSUNG-SGH-I717 using XDA Premium HD app
Yes it flashes the logo twice but it never cuts on and the phone just keeps vibration
Things required:an USB cable which connects your mobile to the pc.
First download samsung kies.
After that,switch off the phone.
Now hold the volume down+home button+power button.
Then when they show do you want to continue press the volume up key.
Now open samsung kies then go to tools and click on firmware upgrade and intialisation.
Then type your model name and serial number.
Now wait for it to complete.
Tadaaa it is fixed.
Click thanks if i helped you.
I am are not responsible for any damages that may happened due to using this guide.
Use this guide at your own risk. I shall not have any liability or responsibility for whatever happens to you and your device by using the instructions in this guide.
The instructions provided in this tutorial for educational purpose only. There is no guarantee that these steps will work for your device.
thanks very much
Though a lot of ppl know these things
Such posts matter a lot for starters who otherwise may do something wrong
Thnx
Sent from my GT-S5282 using Tapatalk
its better to use odin than kies
Sent from my GT-S5282 using Tapatalk
firmware upgrade
jerin jose said:
Things required:an USB cable which connects your mobile to the pc.
First download samsung kies.
After that,switch off the phone.
Now hold the volume down+home button+power button.
Then when they show do you want to continue press the volume up key.
Now open samsung kies then go to tools and click on firmware upgrade and intialisation.
Then type your model name and serial number.
Now wait for it to complete.
Tadaaa it is fixed.
Click thanks if i helped you.
I am are not responsible for any damages that may happened due to using this guide.
Use this guide at your own risk. I shall not have any liability or responsibility for whatever happens to you and your device by using the instructions in this guide.
The instructions provided in this tutorial for educational purpose only. There is no guarantee that these steps will work for your device.
Click to expand...
Click to collapse
it says it cant be upgraded for your device
---------- Post added at 01:30 PM ---------- Previous post was at 01:12 PM ----------
jerin jose said:
Things required:an USB cable which connects your mobile to the pc.
First download samsung kies.
After that,switch off the phone.
Now hold the volume down+home button+power button.
Then when they show do you want to continue press the volume up key.
Now open samsung kies then go to tools and click on firmware upgrade and intialisation.
Then type your model name and serial number.
Now wait for it to complete.
Tadaaa it is fixed.
Click thanks if i helped you.
I am are not responsible for any damages that may happened due to using this guide.
Use this guide at your own risk. I shall not have any liability or responsibility for whatever happens to you and your device by using the instructions in this guide.
The instructions provided in this tutorial for educational purpose only. There is no guarantee that these steps will work for your device.
Click to expand...
Click to collapse
neither kies could be connected in downloading mode.. plz help
I think every one know this way and better is using odin because kies won't detect phones.
Just flash stock firmware through odin.... it will be alright. ..!
If I helped you please press thanks button
Sent from my GT-S5282 using XDA Free mobile app
my worst nightmares
hi.
i was installing a custom ROM on my device and take about one hour and still about 20% of progress so i just Turned my phone off.
and now it doesn't start at all.
it was 100% charged.and now there is no sign of Life in my phone.dose not turn on and no response to charger or usb cable.
Please someone help me.
saadebady said:
hi.
i was installing a custom ROM on my device and take about one hour and still about 20% of progress so i just Turned my phone off.
and now it doesn't start at all.
it was 100% charged.and now there is no sign of Life in my phone.dose not turn on and no response to charger or usb cable.
Please someone help me.
Click to expand...
Click to collapse
I think u may have chosen some ROM not compatible for the phone. Which ROM did u installed?
ankit8395 said:
I think u may have chosen some ROM not compatible for the phone. Which ROM did u installed?
Click to expand...
Click to collapse
i chose the Fake Kitkat Rom for my s5282 device
i was using odin and take too long.
in odin just saw it stuck at "boot.img" so i turned it off and now there is no response .the phone is off.it like there is no battery on.but i tested .the battery is full and on the device but when i push the button nothing happen
saadebady said:
i chose the Fake Kitkat Rom for my s5282 device
i was using odin and take too long.
in odin just saw it stuck at "boot.img" so i turned it off and now there is no response .the phone is off.it like there is no battery on.but i tested .the battery is full and on the device but when i push the button nothing happen
Click to expand...
Click to collapse
Tell me this:-
-From where did u downloaded it? post the link here.
-Is your phone rooted?
Plus i don't know much about installing roms from odin and found that most the procedures use CWM recovery to do so.
ankit8395 said:
Tell me this:-
-From where did u downloaded it? post the link here.
-Is your phone rooted?
Plus i don't know much about installing roms from odin and found that most the procedures use CWM recovery to do so.
Click to expand...
Click to collapse
before i install the rom it was stuck on bootloop so i did resetfactory - wipe cache - wipe dalvik cache and still in bootloop so i downloaded the ROM from
http://forum.xda-developers.com/galaxy-star/development/update-custom-rom-4-2-2-fakeslimkat-t2955068
and because my phone was in bootloop so i couldn't access the SD to put the file in it so the recovery mode had no use to me.
so i used odin.
now my phone is not turn on at all.
how can i get my phone into download mode when its not running?
is there a way to do that?
how can i get the rom into a device that turned off !؟
Please help me.
I NEVER INSTALLED ANY CUSTOM ROM ON MY OWN. FOLLOW THE INSTRUCTIONS BELOW AT YOUR OWN RISK
right now you don't have any operating system on your phone i suppose.
Note: MtkDroidTools gives an option to boot in recovery. I hope it work for you.
Try this:-
-install latest CWM with odin or CWM
-then zapdos kernel (either with odin or cwm)
-then install stock firmware.
If it doesn't work, re-install the kernel.
Good Luck
ankit8395 said:
I NEVER INSTALLED ANY CUSTOM ROM ON MY OWN. FOLLOW THE INSTRUCTIONS BELOW AT YOUR OWN RISK
right now you don't have any operating system on your phone i suppose.
Note: MtkDroidTools gives an option to boot in recovery. I hope it work for you.
Try this:-
-install latest CWM with odin or CWM
-then zapdos kernel (either with odin or cwm)
-then install stock firmware.
If it doesn't work, re-install the kernel.
Good Luck
Click to expand...
Click to collapse
that didn't work.
because my phone doesnt turn on .
if was any way to get it to downloading mode without turning it on maybe there was a way to do the rest with MtkDroid
anyone know another way to do it?
help please
so again >>
before i install the rom it was stuck on bootloop so i did resetfactory - wipe cache - wipe dalvik cache and still in bootloop so i downloaded the ROM from
http://forum.xda-developers.com/gala...imkat-t2955068
i used odin because my phone was in bootloop so i couldn't access the SD to put the file in it so the recovery mode had no use to me.
i was installing the ROM on my device and take about one hour and still about 20% of progress so i just Turned my phone off.
now my phone is not turn on at all.
it was 100% charged
how can i get my phone into download mode when its not running?
is there a way to do that?
how can i get the rom into a device that turned off !؟
saadebady said:
that didn't work.
because my phone doesnt turn on .
if was any way to get it to downloading mode without turning it on maybe there was a way to do the rest with MtkDroid
anyone know another way to do it?
help please
so again >>
before i install the rom it was stuck on bootloop so i did resetfactory - wipe cache - wipe dalvik cache and still in bootloop so i downloaded the ROM from
http://forum.xda-developers.com/gala...imkat-t2955068
i used odin because my phone was in bootloop so i couldn't access the SD to put the file in it so the recovery mode had no use to me.
i was installing the ROM on my device and take about one hour and still about 20% of progress so i just Turned my phone off.
now my phone is not turn on at all.
it was 100% charged
how can i get my phone into download mode when its not running?
is there a way to do that?
how can i get the rom into a device that turned off !؟
Click to expand...
Click to collapse
please some one help me
is my phone dead for real?
now even when i plug the charger ,my phone dose nothing.no light no vibrate
nothing at all
saadebady said:
please some one help me
is my phone dead for real?
now even when i plug the charger ,my phone dose nothing.no light no vibrate
nothing at all
Click to expand...
Click to collapse
no one flAsh rom with odin xcept the stock.
u superbricked ur phone nd now u need to some pro work like giving command on adb to get back ur recovery.
thats it
http://forum.xda-developers.com/showthread.php?p=15330252
My Samsung galaxy gt s5282 stop working since I tried to installed an custom ROM through TWRP RECOVERY APP available on Google app Store .I rooted my phone by using kingroot app nd installed TWRP app too. ln option menu it told me to select your phone model but i didn't get my model number so i choose the similar model of my phone nd click on the "enter to recovery mode" button that was the last time when I saw my phone alive after that my phone got blank it never start ,stuck on the boot image but didn't start. Give me some solutions developers..... Thank you