]I have tried the new bell sbf with great excitement.. unfortunately as with all sbfs I flash it does not complete in the last step around 98%.. I BELIEVE switching to passthrough mode.. on one or two occasions I received a quick usb\vid_05c6epid 9008rev_0000. Qhsusb error on my 64 bit win7 system..could I possibly be missing a driver for that last portion of sbf flash with rsd lite? System still boots but real unstable.. reboots often seeming to look for bp, lol..all other usb functions work well on my pc.. only way it boots is android no bp mode.
Sent from my MB860 using XDA[/QUOTE]
Correction..... qhsusb_dload ...
Sent from my MB860 using XDA
Also tried it on a 32 bit system with same switching error on phone but no driver info .. same stall and fail at usually 98%..
Sent from my MB860 using XDA
Related
I'm trying the flash the 1.83 update to my Atrix and I'm having no trouble with the file or anything but I cannot for the life of me get RSD to recognize my phone.
I'm using Vista 64 bit, yes I have current drivers installed.
USB Debugging is on, USB connection set to none
I'm using RSD 5.0
I'm following all the steps but I can't seem to get it to work.
thezoolander said:
I'm trying the flash the 1.83 update to my Atrix and I'm having no trouble with the file or anything but I cannot for the life of me get RSD to recognize my phone.
I'm using Vista 64 bit, yes I have current drivers installed.
USB Debugging is on, USB connection set to none
I'm using RSD 5.0
I'm following all the steps but I can't seem to get it to work.
Click to expand...
Click to collapse
Did you try a different version of RSD?
Have you also tried this?
" While turning the phone on, hold the Volume Up button until it acknowledges RSD
Your device will say “Starting RSD protocol support”"
Start RSD and see if the phone is there.
I used a couple of the previous versions to no avail and finally tried 5.0
Yes I am booting it into the RSD protocol.
Like I said, I've followed the guide step by step, I've done everything I can think of and have read of and still no luck.
thezoolander said:
I used a couple of the previous versions to no avail and finally tried 5.0
Yes I am booting it into the RSD protocol.
Like I said, I've followed the guide step by step, I've done everything I can think of and have read of and still no luck.
Click to expand...
Click to collapse
You can try the IRC channel. A few people in there might have had the same problem. You can try asking there..
are you using a stock charging cord
and did you try plugging it in the back of the comp
Yes stock cord and back of the comp,I've tried every port I have.
what does this mean? fast boots not working and instead of the device name it just says fastboot. phone works fine im still on 2.2.2 but sbf fails. I've done it before.
help?
what did you do to get this screen?
Sent from my MB860 using XDA App
um the screen is the normal fastboot screen im trying to load an sbf but it keeps failing, phone boot up fine so im thinking its the cable but i have nothing to back this up
full message from the RSD is "unable to retrieve interface handle. (0x7027)"
Maybe try a fruitcake?
Sent from my MB860 using XDA App
Javi97100 said:
Maybe try a fruitcake?
Sent from my MB860 using XDA App
Click to expand...
Click to collapse
the RSD program keeps failing, is their another way to load an sbf. the one thing thats out of place is the name, when i plug the device in the RSD program says device is connected but it also says the device name is fastboot, this should instead show the name of the device connected right?
blackghost1010 said:
the RSD program keeps failing, is their another way to load an sbf. the one thing thats out of place is the name, when i plug the device in the RSD program says device is connected but it also says the device name is fastboot, this should instead show the name of the device connected right?
Click to expand...
Click to collapse
As I know of no, you are holding down vol up+ power right? To get into rsd?
Sent from my MB860 using XDA App
USB debugging enabled?
Updated USB drivers?
Try new computer or cable?
Sent from my MB860 using Tapatalk
Gents
I need your advise.I tried to upgrade my XT910 from GB 2.3.6 to 4.0.4 through RSD.Everything went OK but my XT910 did not start after upgrade.It always stuck on Motorola Logo and try to boot but again going to black screen and then again Motorola logo apperas.
I tried to enter in AP Mode pressing Power+Vol Up+Vol down but it is not going in Recovery and just blinking and then Motorola Logo apperas.
My PC is also not detecinting XT910.It detects only as USB drive.One Driver calls MTP always trying to install on my PC and failed.
Can anyone assist me how to recover it.
masaud said:
Gents
I need your advise.I tried to upgrade my XT910 from GB 2.3.6 to 4.0.4 through RSD.Everything went OK but my XT910 did not start after upgrade.It always stuck on Motorola Logo and try to boot but again going to black screen and then again Motorola logo apperas.
I tried to enter in AP Mode pressing Power+Vol Up+Vol down but it is not going in Recovery and just blinking and then Motorola Logo apperas.
My PC is also not detecinting XT910.It detects only as USB drive.One Driver calls MTP always trying to install on my PC and failed.
Can anyone assist me how to recover it.
Click to expand...
Click to collapse
restart your PC.
Make sure u have all the required drivers for your phone.
Make sure u have the latest RSD.
If possible, try to re-download the fastboot file again.
I hope you are not flashing a ROM through RSD.
All the best.
circleofomega said:
restart your PC.
Make sure u have all the required drivers for your phone.
Make sure u have the latest RSD.
If possible, try to re-download the fastboot file again.
I hope you are not flashing a ROM through RSD.
All the best.
Click to expand...
Click to collapse
Thanks for your advise.I already tried this way but problem is that RSD is not reconsizing XT910.As I mention earlier I can not go in Recovery mode and my PC is also not reconizing XT910.It only reconize it as USB Device and trying to install one driver called MTP but always failed.
masaud said:
Thanks for your advise.I already tried this way but problem is that RSD is not reconsizing XT910.As I mention earlier I can not go in Recovery mode and my PC is also not reconizing XT910.It only reconize it as USB Device and trying to install one driver called MTP but always failed.
Click to expand...
Click to collapse
Then u can do two things. Get hold of another PC, friend, cousin, X GF anyone. And try everything again on that PC.
Also, try to get a new cable. USB cable could be faulty too.
Also , u have written ur phone didn't start after the upgrade. What was the message showing in RSD exactly. And what fast boot files did u use?
Could u post the link??
Sent from my XT910 using Xparent ICS Blue Tapatalk 2
circleofomega said:
Then u can do two things. Get hold of another PC, friend, cousin, X GF anyone. And try everything again on that PC.
Also, try to get a new cable. USB cable could be faulty too.
Also , u have written ur phone didn't start after the upgrade. What was the message showing in RSD exactly. And what fast boot files did u use?
Could u post the link??
Sent from my XT910 using Xparent ICS Blue Tapatalk 2
Click to expand...
Click to collapse
Thanks.I will try using other PC today.I already tried changing other USB cable but result is same.RSD is not reconizing XT910 and MTP driver falied everytime to install when ever I connect XT910 to my PC.
Whenever I connect XT910 to my PC now.It only shows USB of XT910 and ask me to install moto cast from USB.
I downloaded Fastboot file from below link
http://www.eternityproject.eu/topic...-official-fastboot-package-for-motorola-razr/
Look for this thread:
Re: 676.226.3.en.EU (For Retail EU) ICS Leak [UPDATE]
Download the fast boot files from here. U have XT910, GSM RaZr right??
Sent from my XT910 using Xparent ICS Blue Tapatalk 2
My Motorola XT910 did not start after upgrade
Dear All ,
I have the same problem mentioned below
im tring to power on the phone from the power key but nothing happen. when pressing Power+Vol Up+Vol down, It always stuck on Motorola Logo and try to boot but again going to black screen and then again Motorola logo apperas.
have any one a solution for that problem??
"I need your advise.I tried to upgrade my XT910 from GB 2.3.6 to 4.0.4 through RSD.Everything went OK but my XT910 did not start after upgrade.It always stuck on Motorola Logo and try to boot but again going to black screen and then again Motorola logo apperas.
I tried to enter in AP Mode pressing Power+Vol Up+Vol down but it is not going in Recovery and just blinking and then Motorola Logo apperas.
My PC is also not detecinting XT910.It detects only as USB drive.One Driver calls MTP always trying to install on my PC and failed.
Can anyone assist me how to recover it."
I had a problem like this on my xt910 ics. I eventually worked out that I had filled the storage (damn you Gameloft). A full wipe/restore fixed it. I used this utility from droidrzr(dot)com developed mattlgroff. droid-razr-utility-182. Sorry, I can't post links yet...
Sent from my Nexus 7 using xda app-developers app
okay having flash problems with this phone now :S not sure what to do the phone powers on with
SVF:105:1:2
Failed to boot 0X1000
no OS detected going in to RSD mode
this is fine i can select the boot mode whith the loader but when i load the RSD lite flashing
program i load the 4547-fix-try2.sbf file i downloaded from a thred on teh forums.
i start the flash then it gets to part where is needs bypass mode it will not auto select the
bypass mode it needs, so i CAN select it for the divice then after the BP mode it needs to returen to RSD
Mode however the divice does not reset this time so that i cannot reset the phone RSD mode and
thus the phone flashing fails......
However some times it fails on the BP mode as i select to the wrong one at the end of the day the RSD flash tool is
suposed to do this for me and atm it is not doing so.
so currently i am left with a fancy door stop till i can get some help
is there any one that can offer me some advice on this as i carnt think or find a way arround this...
many thanx guys
Only thing I can think of is make sure you haven't plugged into a USB 3.0 jack, it will cause some flaky reactions to the connection
Sent from my MB860 using xda app-developers app
AnotherBill said:
Only thing I can think of is make sure you haven't plugged into a USB 3.0 jack, it will cause some flaky reactions to the connection
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
I wish this laptop is USB2 only mate
I am using WIndows 10 (Maybe that's the problem) and trying to flash stock firmware onto an XT912 via RSD Light. 64bit Moto driver (6.4) were installed. I put the phone into boot mode, and then connect the USB cable, but nothing happens - After awhile it reboots and the computer sees the phone, but I doesn't get seen by RSD. It seems like it is not connecting via the Motot drivers but just the stock ones. I went into Device manager and made sure all the drivers were updated but can't get it to connect. ANy thoughts o what I can do. I have tried reinstalling the drivers multiple times and they seem to be there, phone is just seeing them.
guitar1969 said:
I am using WIndows 10 (Maybe that's the problem) and trying to flash stock firmware onto an XT912 via RSD Light. 64bit Moto driver (6.4) were installed. I put the phone into boot mode, and then connect the USB cable, but nothing happens - After awhile it reboots and the computer sees the phone, but I doesn't get seen by RSD. It seems like it is not connecting via the Motot drivers but just the stock ones. I went into Device manager and made sure all the drivers were updated but can't get it to connect. ANy thoughts o what I can do. I have tried reinstalling the drivers multiple times and they seem to be there, phone is just seeing them.
Click to expand...
Click to collapse
what does it say on phone, in AP Fastboot, complete text?
Sent from my XT912 using Tapatalk
sd_shadow said:
what does it say on phone, in AP Fastboot, complete text?
Sent from my XT912 using Tapatalk
Click to expand...
Click to collapse
Boot Mode Selection Menu (0A.77)
Vol Up Selects, Volume Down Scrolls
Normal Powerup
Recovery
AP Fastboot
BP SBF Flash
BP Only
BP HW Diag & Boot AP
BP Tools
AP Fastboot:
AP Fastboot Flash Mode (S)
0A.77
eWC Info: Size 16G
to return to normal mode - first press power key to power down
Device is LOCKED Status Code : 0
Battery OK
OK To Program
Transfer Mode
USB Connected
When I connect the USB it makes the windows connection sound
guitar1969 said:
Boot Mode Selection Menu (0A.77)
Vol Up Selects, Volume Down Scrolls
Normal Powerup
Recovery
AP Fastboot
BP SBF Flash
BP Only
BP HW Diag & Boot AP
BP Tools
Click to expand...
Click to collapse
no that's the boot menu
select AP Fastboot
Sent from my XT912 using Tapatalk
sd_shadow said:
no that's the boot menu
select AP Fastboot
Sent from my XT912 using Tapatalk
Click to expand...
Click to collapse
I listed it below right after posting original
guitar1969 said:
I listed it below right after posting original
Click to expand...
Click to collapse
which moto drivers version?
rsd lite version?
Sent from my XT912 using Tapatalk
sd_shadow said:
which moto drivers version?
rsd lite version?
Sent from my XT912 using Tapatalk
Click to expand...
Click to collapse
I believe I got the issue resolved. I ended up just using a different method completely(DROID RAZR Utility XT912 Jellybean) skipping the use of RSD Lite and the whole moto driver. From my research it looks like the moto drivers do not work with Win 8.1, so definitely not Win 10 at this time.
You can close the thread.
Thanks for the help.
guitar1969 said:
I believe I got the issue resolved. I ended up just using a different method completely(DROID RAZR Utility XT912 Jellybean) skipping the use of RSD Lite and the whole moto driver. From my research it looks like the moto drivers do not work with Win 8.1, so definitely not Win 10 at this time.
You can close the thread.
Thanks for the help.
Click to expand...
Click to collapse
the utility requires the same drivers.
Sent from my XT912 using Tapatalk