Hi. as title, my X10 wont turn on or charge or being detected by PC companion.
before this happens, my battery was having problem of not charging or difficulty to charge.. when the battery was low, i was in xrecovery(accidently) and then rebooted it. so right now i cant turn on or even charge or being detected by Pc companion.. no green/red light flashing..
any help here please? thanks!
Hey, did you try with another battery of another xperia x10?
did you try to connect to flashtool?
Just to start a little troubleshooting
vichoh said:
Hey, did you try with another battery of another xperia x10?
did you try to connect to flashtool?
Just to start a little troubleshooting
Click to expand...
Click to collapse
hey
i have the same problem
wont respond on usb, tried different battery ( bought a new one ) tried to connect to flashtool
" 05/000/2012 19:00:22 - ERROR -
05/000/2012 19:00:22 - ERROR - Error flashing. Aborted
05/000/2012 19:00:24 - ERROR - Drivers need to be installed for connected device.
05/000/2012 19:00:24 - ERROR - You can find them in the drivers folder of Flashtool.
05/000/2012 19:00:25 - INFO - Device disconnected "
Tried installing the drivers, still didnt work, any suggestions ?!
goodbye x10..
just went to xperia service centre.. maybe a problem with the motherboard of the phone.. owh well..
semirkos said:
hey
i have the same problem
wont respond on usb, tried different battery ( bought a new one ) tried to connect to flashtool
" 05/000/2012 19:00:22 - ERROR -
05/000/2012 19:00:22 - ERROR - Error flashing. Aborted
05/000/2012 19:00:24 - ERROR - Drivers need to be installed for connected device.
05/000/2012 19:00:24 - ERROR - You can find them in the drivers folder of Flashtool.
05/000/2012 19:00:25 - INFO - Device disconnected "
Tried installing the drivers, still didnt work, any suggestions ?!
Click to expand...
Click to collapse
Everytime on the same PC? Did you try connect another? or WinXP and Win 7?
Did u try a SEUS repair?
Take battery out
Load SEUS and select model x10
When it says plug in holding back button attach USB only
Now hold back button while inserting battery
Green light?
If no try another USB cable
If that still doesn't work, id say it's a dead USB port on your phone
Sent from my Xperia X10 using xda premium
Related
Hi, I bricked my SE Xperia X10 Mini pro(u20i). I have root, recovery(CWM) and CyanoComb v1.4. When I rebooted phone, unlocked screen it shows errors about apps that they closed and than the phone rebooted. I can't do nothing, go to recovery is impossible. I tried flashtool but it's need to enable uknown sources an debugging but i can't go to system. SEUS didn't respond when i connect the phone with back button... HELP ME! Thanks
Edit: Now i see that the Flasher shows error after plugin phone in flash mode. HELP!
I looked into my magic glass bowl and saw that you did something and my future cards said you will have gotten some help. But not specifically.
I hope this disburdens yourself a bit.
Now after you cooled down and recognized that the information(s) you gave us is too unspecific you can go on to give more informations.
But first:
Doi you have the correct ftf file(s) for flashtool? Flashtool does not need to have anything enabled on your phone. Also SEUS should work. If not you bricked your phones hardware.
My guess is you did not correctly follow the instructions to use SEUS. Follow them step by step. They are well explained. Possibly you haven't the correct driver on your PC... But this did not tell me my glass bowl, this stupid thing. May you tell us what operating system you use? Maybe reinstalling SEUS will help. Do you have the actual VFewrson of SEUS? I guess SEUS is the better choice then flashtool for you. (both do the same but flashtool can flash other roms)
Good luck.
I have W7 and XP, i tried SEUS and Flashtool on both. I downloaded UK 2.1 ROM and than I did .ftf file. After i enter flash mode in Flashtool it say: Error Flashin Aborted, Now unplug your device and power it on, turn on Uknown sources and Debugging.
In SEUS, when it ask to turn in flash mode, I do it but SEUS didn't recognize my device.
26/007/2011 21:07:38 - INFO - Preparing files for flashing
26/007/2011 21:07:45 - INFO - Searching Xperia....
26/007/2011 21:07:46 - ERROR - Please plug you device in flash mode
26/007/2011 21:07:47 - INFO - Searching Xperia....
26/007/2011 21:07:47 - ERROR - Please plug you device in flash mode
26/007/2011 21:07:48 - INFO - Searching Xperia....
26/007/2011 21:07:49 - ERROR - Please plug you device in flash mode
26/007/2011 21:07:50 - INFO - Searching Xperia....
26/007/2011 21:07:50 - ERROR - Please plug you device in flash mode
26/007/2011 21:07:51 - INFO - Searching Xperia....
26/007/2011 21:07:51 - INFO - Found at USB\VID_0FCE&PID_ADDE\5&F9CB627&0&1
26/007/2011 21:07:51 - INFO - Start Flashing
26/007/2011 21:07:51 - INFO - VER="R8A026";DATE="20100412";TIME="11:41:00";
26/007/2011 21:07:55 - ERROR - Error flashing. Aborted
26/007/2011 21:07:55 - INFO - Now unplug the device and power it on
26/007/2011 21:07:55 - INFO - Then go to application settings
26/007/2011 21:07:55 - INFO - turn on Unknown Sources and Debugging
@wOrHeR SvK: i had the same behaviour with Flashtool, so i powered off the device, powered on in flash mode and reflashed with FlashTool, after that it was flashed fine (don't follow the ending message to activate unknown sources and other crap, you don't need it... focus only at flash stage, that's what you need).
By the way Snoopo is right, flashing with SEUS (open application and search for "repair your phone" or something like that) does the job in every circumstance but hardware failure.
Good luck!
nothing... I turned on in flash mode and than click flash in Flashtool. Same problem... SEUS can't recognize... I Don't know why but before it was OK
tommorow i will go to my friend and try it at his PC
redownload the ftf file... did you possibly load a mini (u10) file instead a x10 mini pro (u20)?
did you use the right version of Flashtool? The one from Androxyde/Bin4ry [http://forum.xda-developers.com/showthread.php?t=920746]?
Use SEUS to reinstall your ROM
yeah, tried 0.2.8 and 0.2.9.1. SEUS still not working...
Correct Flashfiles are here: http://forum.xda-developers.com/showthread.php?t=826455
And SEUS also should work. What are the error messages? Make sure your phone is really OFF, start SEUS choose "x10 mini pro" (NOT "mini pro" without "x10" - this is a coplete new model and not really released yet) and go through the process until it says you have to connect your phone and do it exaclty like it is explained: hold the back-button while you are connecting your phone hold it down as long as it is looking for your phone when it starts flashing you can release the button. there should be the green indicator LED showed while the restore is running.
The Flashtool ones you pasted look like the flashmode is started successfully but it is possibly a wrong flash file. So try the correct one(s) (rename the .rar file downloaded from page above into .ftf)
otherwise you really bricked your boot partition and can try if SE wants to rescue your phone or if it says that your warranty is void...
SEUS still nothing, tried everything... Flashtool: when i first turn phone on to flash mode and than click flash in flashtool, it say Start Flashing and than the Error but when it says the error the green led is off and the phone is going to start... any idea ?
also SEUS isn't showing any errors, just say that i have to connect phone in flash mode...
I can boot to system but in system it showing errors about apps thah must close.... That isn't bricked boot patriton i think.
wOrHeR SvK said:
SEUS still nothing, tried everything... Flashtool: when i first turn phone on to flash mode and than click flash in flashtool, it say Start Flashing and than the Error but when it says the error the green led is off and the phone is going to start... any idea ?
also SEUS isn't showing any errors, just say that i have to connect phone in flash mode...
I can boot to system but in system it showing errors about apps thah must close.... That isn't bricked boot patriton i think.
Click to expand...
Click to collapse
You have DEFINATLY got the device drivers?
Dev area
should be moved, but noobs dont read the stickies
I have installed drivers with ggsetup
I asked ide Dev area beacause this area read more people than Question area
wOrHeR SvK said:
I have installed drivers with ggsetup
I asked ide Dev area beacause this area read more people than Question area
Click to expand...
Click to collapse
not for brick questiions ! The ansers always the same to noobs seus is not pc companion
i know what is SEUS and what is PC Companion I'm no n00b but SEUS and FlashTool is not working for me, i try it on another PC, with another USB cable...
wOrHeR SvK said:
I have installed drivers with ggsetup
I asked ide Dev area beacause this area read more people than Question area
Click to expand...
Click to collapse
its driver problem
ggsetup driver wont work with flash tool or sony update
remove driver then install seus
download seus from here http://www.sonyericsson.com/cws/support/mobilephones/downloads/subject/updateservice/xperiax10minipro?cc=us&lc=en
its Update Service not pc companion
it will work 100 % if you have right driver and not failed phone hardware
USB Driver for x10mini
download USB driver from here
http://developer.sonyericsson.com/wportal/devworld/downloads/download/dw-x10minidrivers?cc=gb&lc=en
wOrHeR SvK said:
i know what is SEUS and what is PC Companion I'm no n00b but SEUS and FlashTool is not working for me, i try it on another PC, with another USB cable...
Click to expand...
Click to collapse
Hmmmmmmm.
Hello everyone,
I am a noob and I tried to update my X10a (Rogers) from PC Companion and it wouldn't work even though I am at firmware 2.1.
Then I decided to do an update with flashtool. But everytime I connect to flashtool it gives me this error:
18/024/2011 19:24:39 - ERROR - Error flashing. Aborted
18/024/2011 19:24:39 - INFO - Now unplug the device and power it on
18/024/2011 19:24:39 - INFO - Then go to application settings
18/024/2011 19:24:39 - INFO - turn on Unknown Sources and Debugging
18/024/2011 19:24:39 - INFO - Device connected in flash mode
18/026/2011 19:26:13 - INFO - Device disconnected
and I have turned on the Unknown Sources and USB Debugging on the phone yet it keeps giving me the same error over and over again.
Even when I tried to upgrade it to the Generic 2.3 it would still give me this error.
I don't know what I am doing wrong or if it is just my stupid phone.
I downloaded all the .ftf files from here.
I also downloaded the flashtool from here.
Please help me. I would really appreciate it.
goto driver folder in flashtool folder and run ggsetup then try again
Redownload file and try again
AND
When flashtool says to connect in flashmode put the phone in flash mode that time
Don't put it in flashmode before it
i did both...still not working
one thing i do notice is that everytime I connect my phone with the USB I get the pop-up "Connect phone/Install PC Companion/Charge Phone"
If I select Connect phone and a few seconds later I take out the USB and plug it back in I get that popup in the phone again...could this be a problem?
Someone help me please, I was trying to re-lock the boot loader on my xperia s with flashtool 0.8.6.0 folowing the guide on here and now I'm stuck in flashmode I've tried a hard reset, flashing stock ftf and nothing's working flashtool just say's --flashing finished
-please wait phone will reboot
-for flashtool unknown sources and debugging must be checked in the phone settings
-device connected in flashmode
I really hope the phone is not bricked any help very much appreciated guys
Simon
super hans said:
Someone help me please, I was trying to re-lock the boot loader on my xperia s with flashtool 0.8.6.0 folowing the guide on here and now I'm stuck in flashmode I've tried a hard reset, flashing stock ftf and nothing's working flashtool just say's --flashing finished
-please wait phone will reboot
-for flashtool unknown sources and debugging must be checked in the phone settings
-device connected in flashmode
I really hope the phone is not bricked any help very much appreciated guys
Simon
Click to expand...
Click to collapse
Did you try to post in the same thread you got the instruction?
So have unplug the device but the LED green light is on? the Vol+ & power together till three vibrates didn't work?
Yes thats right if i unplug the device the LED goes out but when i push the power button it just flashes green and nothing happens, I've tried the volume up + power it vibrates 3 times like normal but when i push the power button the same happens green LED flash
no I haven't tried that I'll post it in there now cheers for the advice
flash the firmware again, and when you plug in the phone, hold the volume down button only, you dont have to hold the power one, it should go into flash mode now
super hans said:
Yes thats right if i unplug the device the LED goes out but when i push the power button it just flashes green and nothing happens, I've tried the volume up + power it vibrates 3 times like normal but when i push the power button the same happens green LED flash
no I haven't tried that I'll post it in there now cheers for the advice
Click to expand...
Click to collapse
unplug the cable from your phone, then hold the vol + and power till vibrates three times. now your phone is off,
lunch flashtool and initiate the flashing process with ICS firmware and hold vol - and plug the phone in, see if that works.
Sony developer on the forum believe that no one could hardly brick a Sony phone.
it wont let me flash ftf as it keeps dropping out of flashmode then re entering it flashtool is saying
-ERROR flashing aborted
-device disconnected
-device connected in flashmode
over and over again, I can get it into fastboot mode is there anyway I can re flash ftf in fastboot through cmd?
I think the battery might be dead now when I connect it all i get is a red LED
Hello!
It appears I have the same issue with xperia pro. After flashing the official 4.0.4 rom with flashtool the log says:
Code:
27/032/2012 15:32:18 - INFO - Flashing finished.
27/032/2012 15:32:18 - INFO - Please wait. Phone will reboot
27/032/2012 15:32:18 - INFO - For flashtool, Unknown Sources and Debugging must be checked in phone settings
27/032/2012 15:32:18 - INFO - Device connected in flash mode
The phone doesn't respond, the green led is on.
Have you been able to restore the phone functioning?
---------- Post added at 02:56 PM ---------- Previous post was at 02:40 PM ----------
Ah, it's okay. I re-flashed the phone with a different rom and now it is working fine.
Hi.
I had a similar issue on a Xperia Play. Try this: http://forum.xda-developers.com/showthread.php?t=1126358
relocked bootloader trough flashtool to see if i could get bravia engine 2 working and now my phone won't start, just vibrates one time and green led light and thats it.
help please!!!!!
hackerpower said:
relocked bootloader trough flashtool to see if i could get bravia engine 2 working and now my phone won't start, just vibrates one time and green led light and thats it.
help please!!!!!
Click to expand...
Click to collapse
try to flash a new stock rom.
my phone stucked on flash mode and the problem is i cant get it on like usual.. im using xperia u.. and before flashing i forgot to enable usb debuging and now its stuck on flash mode!
HELP
Ali Suhaimi said:
my phone stucked on flash mode and the problem is i cant get it on like usual.. im using xperia u.. and before flashing i forgot to enable usb debuging and now its stuck on flash mode!
HELP
Click to expand...
Click to collapse
Calm down dude. Grab flashtool. Set flashmode and choose your stock ROM. And just flash it through vol down key and plug in USB to your phone. It is just a soft-brick. No need to worry much.
Sent from my ST25i using Tapatalk 2
the problem is i didnt enable my usb debugging before that so when i connect to laptop its says that the device malfunctioned.. so what to do??
Ali Suhaimi said:
the problem is i didnt enable my usb debugging before that so when i connect to laptop its says that the device malfunctioned.. so what to do??
Click to expand...
Click to collapse
YOU DON'T NEED TO ENABLE USB DEBUGGING IF YOU'RE GOING TO BOOT FLASHTOOL!!!
Sent from my ST25i using Tapatalk 2
Ali Suhaimi said:
my phone stucked on flash mode and the problem is i cant get it on like usual.. im using xperia u.. and before flashing i forgot to enable usb debuging and now its stuck on flash mode!
HELP
Click to expand...
Click to collapse
Fiest thing first, what phone is it?
Try to explain exactly what have you done, and how do you tell it's in flashmode?
Okay.. im using xperia u.. im trying to downgrade it to GB.. and im using flashtool.. but when i
connect it,it says that 'The last USB device you connected to this computer malfunctioned,and windows does not recognize it'.. and the flashtool says that devide connected in flashmode..
04/045/2013 10:45:44 - INFO - Device connected in flash mode
04/045/2013 10:45:46 - INFO - Device disconnected
04/046/2013 10:46:03 - INFO - Device connected with USB debugging off
04/046/2013 10:46:07 - INFO - Device disconnected
04/048/2013 10:48:26 - INFO - Selected st25i_2.3.7_t-mobile hu_6.0.b.3.184.ftf
04/048/2013 10:48:26 - INFO - Preparing files for flashing
04/048/2013 10:48:40 - INFO - Searching Xperia....
04/048/2013 10:48:40 - ERROR - Please plug you device in flash mode
04/048/2013 10:48:41 - INFO - Searching Xperia....
04/048/2013 10:48:41 - ERROR - Please plug you device in flash mode
04/048/2013 10:48:42 - INFO - Searching Xperia....
04/048/2013 10:48:42 - ERROR - Please plug you device in flash mode
04/048/2013 10:48:43 - INFO - Searching Xperia....
04/048/2013 10:48:43 - ERROR - Please plug you device in flash mode
04/048/2013 10:48:44 - INFO - Searching Xperia....
04/048/2013 10:48:44 - ERROR - USB\VID_0FCE&PID_ADDE\5&9854CDB&0&1
04/048/2013 10:48:45 - INFO - Device connected in flash mode
04/048/2013 10:48:45 - INFO - Searching Xperia....
04/048/2013 10:48:45 - ERROR - USB\VID_0FCE&PID_ADDE\5&9854CDB&0&1
04/048/2013 10:48:46 - INFO - Searching Xperia....
04/048/2013 10:48:46 - ERROR - USB\VID_0FCE&PID_ADDE\5&9854CDB&0&1
04/048/2013 10:48:47 - INFO - Device disconnected
04/048/2013 10:48:47 - INFO - Searching Xperia....
04/048/2013 10:48:47 - ERROR - Please plug you device in flash mode
04/048/2013 10:48:48 - INFO - Searching Xperia....
04/048/2013 10:48:48 - ERROR - Please plug you device in flash mode
and now when im trying to turn on my phone the green light flashes but the screen only show ! sign in a triangle with a phone.. then it turns off..
@Ali Suhaimi
Id the phone turned off before you start flashing?
Did you install the drivers from flashtool located in drivers directory? You need to install 4, the one for Sola and flash and fastboot mode that are at the bottom of the list.
Before you flash just leave flashtool open and connect in flash mode, and see it stays connected for about 45 seconds.
Yes i've done all.. but the problem is i forgot to enable USB Debugging before flashing it.. and now the flashtool need the USB debugging to be enabled and i cant turn on the phone,.
Ali Suhaimi said:
Yes i've done all.. but the problem is i forgot to enable USB Debugging before flashing it.. and now the flashtool need the USB debugging to be enabled and i cant turn on the phone,.
Click to expand...
Click to collapse
Bo USB devugging has absolutely nothing to do with flasg mode as was posted before vy Little Zed.
What is your windows version?
Please post a log of dlashtool fr connecting in flash mode. Do not flush anything just open flashtool and connect in flash mode.
yesterday I got xperia p with boot problem
it keeps rebooting after Xperia logo
I tried to flash it with Flashtool and SEtool but when I start falshing with flashtool it will stuck in reading device info
14/028/2012 13:28:17 - INFO - Device connected in flash mode
14/028/2012 13:28:45 - INFO - Selected LT22i_6.0.B.3.162_NCB.ftf
14/028/2012 13:28:45 - INFO - Preparing files for flashing
14/028/2012 13:28:54 - INFO - Please connect your device into flashmode.
14/028/2012 13:28:56 - INFO - Opening device for R/W
14/028/2012 13:28:56 - INFO - Reading device information
Click to expand...
Click to collapse
and when I try to flash it or getting device info with SEtool box it will stuck in "push volume down or back key and connect your device via usb" and the green bar get full and blank
it seems to be drivers problem so I installed all flashmode, fastboot and Xperia P adb drivers from flashtool drivers package
I also tried 2 windows PCs
1- Win 7 , 32 bit
2- Win XP
but no result
thanks in advance for all your helps
try to install pda.net it will re-install your driver.
mharckk said:
try to install pda.net it will re-install your driver.
Click to expand...
Click to collapse
I tried pdanet to re-install my drivers but its about adb drivers not flashmode
I also tried SUS and now I'm almost sure that this problem comes from Drivers cuz SUS doesn't recognize my device when the green led is on and in device manager my phone is named SEMC flash device and here I also changed the driver manually to STE8500.inf from flashtool driver
and there is no good result till now :|
Drivers
Its all about the drivers. Install SUS, Gordons Gate Flash Drivers, The Flash drivers from flash tool and finally turn off the phone holding power button and volume up for 30 seconds and try flashing it again
DavidMKD said:
Its all about the drivers. Install SUS, Gordons Gate Flash Drivers, The Flash drivers from flash tool and finally turn off the phone holding power button and volume up for 30 seconds and try flashing it again
Click to expand...
Click to collapse
Hi again
I do all things which might help updating drivers and so on
but no answer from phone
I thought that this might be because of boot problem
is there any way not use jtag or other ways of boot repair to do this job?
Hello everyone, it's noob number #16723009. This poor noob in question was so fascinated by the world of rooting , kernels and roms, so he got a bit too far ahead of himself! So I experimented with rooting my Sony Xperia Go and trying a few different Rom's. End result: Sony bootscreen brick.
And unfortunately no backups were made.
So this is order of actions:
1) root with Root_with_Restore_by_Bin4ry_v18 XDA link
2) installed Clockwork Mod recovery XDA link
3) in CWM Recovery wipe data/factory reset, wipe cache partition, wipe dalvik cache
4) in CWM Recovery install zip from sdcard: Speedydroid v15 XDA link , in Aroma I deleted "unnecessary" bloatware (resulting with a semi-functional rom, nice fast and snappy but for instance pictures didn't open)
5) Same procedure as nr 3.
6) in CWM recovery install zip from sdcard: TheBrainsRom v4 XDA link , (resulting in a continous loop between sony and the rom bootscreen).
7) PANIC PANIC! in CWM recovery under mounts and storage menu : format system or format cache (don't remember)
Finally resulting me with a phone, which hangs at SONY logo. Volume up + powerbutton reset works.
I tried Flashtool's flashmode to install the stockrom, resulting in red" ERROR, flash aborted" in the log. Sometimes the Sony PC companion popup with " Sony xperia go connected" comes up while I'm trying to flash, but it disappears in ~5 secs. So when I hold the Volume Down button when I connect the usb cable, the indicator light does go Green, but it turns red in ~5 sec and the phone goes back to the SONY logo
Log:
26/042/2013 16:42:00 - INFO - Selected st27i_6.0.B.3.184_Original.ftf
26/042/2013 16:42:00 - INFO - Preparing files for flashing
26/042/2013 16:42:07 - INFO - Please connect your device into flashmode.
26/042/2013 16:42:26 - INFO - Device connected in flash mode
26/042/2013 16:42:26 - INFO - Opening device for R/W
26/042/2013 16:42:26 - INFO - Start Flashing
26/042/2013 16:42:26 - INFO - Processing loader
26/042/2013 16:42:26 - INFO - Checking header
26/042/2013 16:42:26 - INFO - Ending flash session
26/042/2013 16:42:26 - ERROR -
26/042/2013 16:42:26 - ERROR - Error flashing. Aborted
26/042/2013 16:42:26 - INFO - Device connected in flash mode
26/042/2013 16:42:34 - INFO - Device disconnected
I also tried PC companion "repair my phone" option. Nothing just happens after Vol Down + usb cable in procedure.
Also the same problem with Sony Update Service.
I have googled and read stuff about this issue for solid 8 hours, no one seems to have the same exact issue. Should I start thinking of it as paperweight or is there hope ?
U r not connecting the phone properly while flashing
Make sure phone is off and disconnected
Go to flashtool and select ur file and click flash
Now it will prepare files and ask u to connect ur phone
When it asks ,make sure ur phone is switched off
Just press the volume down button ( keep it pressed) and connect to usb and wait for flashing to b finished
drsanket_xperia_u said:
U r not connecting the phone properly while flashing
Make sure phone is off and disconnected
Go to flashtool and select ur file and click flash
Now it will prepare files and ask u to connect ur phone
When it asks ,make sure ur phone is switched off
Just press the volume down button ( keep it pressed) and connect to usb and wait for flashing to b finished
Click to expand...
Click to collapse
I am actually doing it the exact way you described. Still no use.
please , suggest some solution... i have same problem with my xperia sola.. pllzzzzzzzzzzzzzzz help
Which os on computer?? Did u installed flashmode drivers?
I get the same problem sometimes. I usually fixed it by using a different USB port. Try that
Sent from my Xperia Yoo
CrazyXperiaA said:
I get the same problem sometimes. I usually fixed it by using a different USB port. Try that
Sent from my Xperia Yoo
Click to expand...
Click to collapse
My OS is Win 8 64 bit, yes I do have Flashmode drivers installed, I will try different usb ports, thanks!
EDIT: It did not work on any USB 3.0 port on my asus n56vz. I installed flashtool, copied the tft to my old win7 lenovo x61s laptop with usb 2.0 ports, 3 tries and it worked ! Thanks fellas!