i tried to flash 2.2 using odin but i cant select reboot or any other command on the list.. what do i do? or is my phone done?
Lavundra21 said:
i tried to flash 2.2 using odin but i cant select reboot or any other command on the list.. what do i do? or is my phone done?
Click to expand...
Click to collapse
No sir, you should be just fine, try to reflash back to stock using odin, pull the battery remove the sim and sd card, and then go into downloader mode, and try again.
stock FW here, good luck.
Lavundra21 said:
i tried to flash 2.2 using odin but i cant select reboot or any other command on the list.. what do i do? or is my phone done?
Click to expand...
Click to collapse
Read the froyo thread you need to adb reboot
Sent from my SGH-T959 using XDA App
still cant get it to work... i dunno what im doing wrong. but it seems like all the files needed arent in the link from above.
Keep trying
Try enter "downloading mode" with the sd card in the phone(after many attempts it worked for me), there is a thread in this forum about how to enter "downloading mode" and flash the phone.
still cant get out of the android system recovery mode.. ive tried holding buttons down while turning the phone on and off and theres nothng happening. still cant use the power button as the ok.
i got the same problem i cant use any button as ok
is there a way to get the ok button, or what i can do to get over this problem
thanks in advance
Let me know if these steps help:
Here is a couple of methods to get into download mode. Once you get to
download mode, follow the directions in second part of my post...
First Method
1) Pull the battery, sim card, and sd card.
2) Reinsert battery but do not press any buttons.
3) Plug into usb that is connected to your computer. If something shows up
on the screen (charging logo) then you should be golden.
4) Hold the vol up, vol down, and power until the screen comes on,
immediately release the power button but not the other two. Hopefully it
will boot into download mode and than you can use Odin to get back to stock.
Second Method
1) Another method that seems to work for some people is to pull the battery,
sim, sd card.
2) Reinsert battery and hold both volume buttons but do not press power
button.
3) Then plug in usb. The phone should boot into download.
Third Method
1) You will need the samsung ADB drivers installed for your phone and ADB.
Samsung Drivers for 32 bit Windows: http://files.androidspin.com/downlo...=SAMSUNG_USB_Driver_for_Mobile_Phones_x86.exe
Samsung Drivers for 64 bit Windows: http://files.androidspin.com/downlo...ung/vibrant/&file=usb_drivers_GalaxyS_x64.zip
2) Remove sim card and sd-card. Remove the battery.
3) Hold buttons vol up, vol down, and power.
4) While holding down those 3 buttons put the battery back in and keep
holding all 3 buttons until the vibrant disappears and reappears. Once it
reappears, release all 3 buttons.
5) Now connect your phone to your pc via USB cable.
6) Open a cmd prompt and navigate to the folder with ADB and type "ADB
REBOOT DOWNLOAD" caps are not necessary.
7) Your phone will reboot into the download
How to get back to stock once in Download Mode:
Download the files in the linked thread and follow the directions there or
the ones in my post below.
Odin and Files Needed Available Here: http://forum.xda-developers.com/showthread.php?t=734475
1) Open Odin and verify that one of the Com ports shows a device connected.
If it doesn't try using a different usb port.
2) Load the .pit and pda files. It should be pretty obvious how to do that
once you are in Odin.
3) Make sure that the option to partition is unchecked. The other two
options should be checked.
4) Hit start and wait.
5) Your phone will restart when Odin is done and you will be good to go.
Seems to be the same issue
I just tried upgrading to 2.2 using Odin and this seems to be the same problem. It seems that every solution starts with, "Enter Into Download Mode..." but no method seems to work.
I wouldn't say the phone is "bricked" as when it is plugged into a computer it will install the drivers and Odin sees it, but I can't get it into anything but recovery mode.
The buttons seem to be strangely mapped, the up and down buttons are reversed and the power button doesn't seem to be working as the "Ok" button. The menu toggles the recovery screen and the <!> graphic with the Android. Anyone figured out how to solve this? In the meantime I will continue attempting to get into download moad.
Hi, I have the same exact problem. Stuck in system recovery. Volume buttons reversed. Power button does nothing. Cannot get into download mode. Please Help
what happened?
I just got the same issue :S
the volumes buttons are wrong and the power (OK) button is not working on system recovery mode...
any help?
same problem - samsung galaxy vibrant
brianking21 said:
Hi, I have the same exact problem. Stuck in system recovery. Volume buttons reversed. Power button does nothing. Cannot get into download mode. Please Help
Click to expand...
Click to collapse
can't mount /dev/block/mmcblk0p1
(invalid argument)
e:copya_dbdata_media:can't mount SDCARD:
your storage not prepared yet, please use UI menu for format and reboot actions
copy default media content failed
Folks, any update regarding this problem. I got very same problem, and could not find a solution yet.
hints?
I have the same problem also. I got into the problem by following a thread down grading to 2e version from 3e version. I've tried lots of things including going back to stock--or what I think is stock. I now have the 3e version again but when I bring up recovery mode the up/down buttons are backwards and the ok (power) key doesn't work.
Suggestions? HELP?
We can get into root console and manually tweak files if that will help.
UPDATE----SOLUTION
I got this working by reloading the stock t-mobile kernel from http androidspin.com/2010/08/09/how-to-restore-or-recover-your-samsung-vibrant/. This link provided at that site is single file so just use the pda and pit boxes in odin. In desperation I selected re-partion and Phone bootloader update.
I was unable to get into the recovery console with hitting any keys but adb did the trick. Volumn-up and power gets into the flash download
Finally Fixed it
I finally was able to get the phone into download mode by holding down the volume up key, the search key and the power key.
It seems the key mapping was just messed up.
After it entered download mode I followed the guide on androidspin /2010/08/09/ how-to-restore-or-recover-your-samsung-vibrant (add the .com to androidspin, forum won't let me post links yet)
Hi How did you hold the search key. It does not light up till the vibrant shows on screen. Can you please explain how to managed to hold vol up, power and search together? thanks
Sivaavis its only a 3-button combo, not 4. Why u holding down search? Its up,down volume and power and then when the vibrant logo shows u let go of power.
Sent from my SGH-T959 using XDA Premium App
If you are in recovery mode just go into adb and type in:
adb reboot download
You should be in download mode
ok look heres what i did straight to the point am i soft are hard bricked? I got to 99.99% of the sbf flash then failed I get code 0x1000 Failed to boot cant load OS But But heres the hope I get like 9 options i can put the phone in on this black screen with white writing options like RSD mode Fastboot NvFlash and others to select one i press the up button i ran sbf flash again in Rs mode but it just fails soon as i hit start my question is can this be fixed with sat fastboot adb and if so what file do i use any links thanks and my Atrix was on 2.3.4 4.5.91
Thanks in Advanced
Were you flashing pudding?
nucentury08 said:
ok look heres what i did straight to the point am i soft are hard bricked? I got to 99.99% of the sbf flash then failed I get code 0x1000 Failed to boot cant load OS But But heres the hope I get like 9 options i can put the phone in on this black screen with white writing options like RSD mode Fastboot NvFlash and others to select one i press the up button i ran sbf flash again in Rs mode but it just fails soon as i hit start my question is can this be fixed with sat fastboot adb and if so what file do i use any links thanks and my Atrix was on 2.3.4 4.5.91
Thanks in Advanced
Click to expand...
Click to collapse
live4nyy said:
Were you flashing pudding?
Click to expand...
Click to collapse
yes i was is that right
I'm assuming you were coming from the OTA 2.3.4. Is that right?
If so, then it is a soft brick and you just need to power it down and then plug it back in to the computer and it should turn on by itself. As soon as the menu comes back up, use the VOL down to navigate to Fastboot and then press VOL up to select. Once in Fastboot protocol, you can just reenter the fastboot unlock commands, make sure you enter your uniqueID exactly
nucentury08 said:
yes i was is that right
Click to expand...
Click to collapse
live4nyy said:
I'm assuming you were coming from the OTA 2.3.4. Is that right?
If so, then it is a soft brick and you just need to power it down and then plug it back in to the computer and it should turn on by itself. As soon as the menu comes back up, use the VOL down to navigate to Fastboot and then press VOL up to select. Once in Fastboot protocol, you can just reenter the fastboot unlock commands, make sure you enter your uniqueID exactly
Click to expand...
Click to collapse
can you link me to the fastboot unlock zip
Just download this and use option 3.
http://forum.xda-developers.com/showthread.php?t=1182871
nucentury08 said:
can you link me to the fastboot unlock zip
Click to expand...
Click to collapse
Hi there guys, first of all thank you all so much for the support here.
I have a problem with my atrix, i googled a lot before posting, but i still can't find a solution:
I have a atrix 4G, unlocked, was running successfully neutrino 2,8 version.
After 2 months of being (almost) fully functional, the phone crashed(i didn't do anything particular at that time, i think that i was browsing google maps) suddenly and now i have continuous boot loop, i get only the classic red dual core logo, with the "unlocked" notification over it, and then after 10-15 sec it reboots.
I try to open it with holding volume down, to enter recovery, nothing happens. It reboots again. The computer doesn't see it, in this case.
I reboot it with holding volume up, says "starting RSD protocol suppport", and pc sees it and i get the cling-clong sound of usb.
I would do the recovery using rsd, but i read that it is not for unlocked devices, is this so? What can i do in this case? Thanks a lot!!!
ergotelis said:
Hi there guys, first of all thank you all so much for the support here.
I have a problem with my atrix, i googled a lot before posting, but i still can't find a solution:
I have a atrix 4G, unlocked, was running successfully neutrino 2,8 version.
After 2 months of being (almost) fully functional, the phone crashed(i didn't do anything particular at that time, i think that i was browsing google maps) suddenly and now i have continuous boot loop, i get only the classic red dual core logo, with the "unlocked" notification over it, and then after 10-15 sec it reboots.
I try to open it with holding volume down, to enter recovery, nothing happens. It reboots again. The computer doesn't see it, in this case.
I reboot it with holding volume up, says "starting RSD protocol suppport", and pc sees it and i get the cling-clong sound of usb.
I would do the recovery using rsd, but i read that it is not for unlocked devices, is this so? What can i do in this case? Thanks a lot!!!
Click to expand...
Click to collapse
You'll probably need to flash a new recovery partition. Check out this thread:
http://forum.xda-developers.com/showthread.php?t=1950307
RaiderDuck said:
You'll probably need to flash a new recovery partition. Check out this thread:
http://forum.xda-developers.com/showthread.php?t=1950307
Click to expand...
Click to collapse
Thanks, but the problem is that this guy can get into the recovery with powering up+holding volume down button, if i understood well.but I can't!
ergotelis said:
Thanks, but the problem is that this guy can get into the recovery with powering up+holding volume down button, if i understood well.but I can't!
Click to expand...
Click to collapse
flasing a recovery is done via fastboot so you don't have to enter recovery but fastboot (hold power and volume down till it shows fastboot, then press up) .
look at this post: http://forum.xda-developers.com/showpost.php?p=33137046&postcount=10
Fix
ergotelis said:
Hi there guys, first of all thank you all so much for the support here.
I have a problem with my atrix, i googled a lot before posting, but i still can't find a solution:
I have a atrix 4G, unlocked, was running successfully neutrino 2,8 version.
After 2 months of being (almost) fully functional, the phone crashed(i didn't do anything particular at that time, i think that i was browsing google maps) suddenly and now i have continuous boot loop, i get only the classic red dual core logo, with the "unlocked" notification over it, and then after 10-15 sec it reboots.
I try to open it with holding volume down, to enter recovery, nothing happens. It reboots again. The computer doesn't see it, in this case.
I reboot it with holding volume up, says "starting RSD protocol suppport", and pc sees it and i get the cling-clong sound of usb.
I would do the recovery using rsd, but i read that it is not for unlocked devices, is this so? What can i do in this case? Thanks a lot!!!
Click to expand...
Click to collapse
hello i had this problem yesterday, it happens in neutrino rom to alot of people!
and btw i could not open recovery either
ill explain what i had to do
i had to use moto-fastboot and install a new recovery, basically your recovery is dead and your rom is unbootable
heres the steps
download the moto drivers and install
http://forum.xda-developers.com/attachment.php?attachmentid=1381183&d=1349549067
then download the motofastboot zip http://forum.xda-developers.com/attachment.php?attachmentid=1381414&d=1349555102
and create a new folder in C: (computer) called Android and then drag the files from the moto zip into android
Then download a new recovery http://www.mediafire.com/?6ww8wrjrdqq9m97
place the recovery.img into the android folder
now you have all the files needed to reflash your new recovery and fix your phone the whole idea is to reinstall recovery so you can access it and wipe and install the rom fresh again
now you need to do these steps
1) Attach your phone to the PC via USB (use a port closest to the power supply)
2) Reboot phone while holding volume down until you see "fastboot"
3) Press volume up to initiate fastboot
4) On your PC click the Start menu, then in the search box type "cmd"
5) In the command prompt type the following commands (no quotes, hit enter after each command)
6a) "cd c:/android"
6b) "moto-fastboot devices"
your CMD promt should show something like this
C:\Users\Me>cd c:/android
c:\Android>fastboot devices
TA20703SX9 fastboot
c:\Android>
now if that has all worked type the following phrases
moto-fastboot erase recovery
moto-fastboot flash recovery recovery-clockwork-6.0.1.4-maguro.img
moto-fastboot reboot
now the phone should reboot, unplug the usb and pull battery out.
put battery back in and then try to boot into recovery like you normally would (power button + Vol Down)
and your new recovery should load!
from here you can wipe your whole system which i would reccomended as your current one is corrupt and install a new rom or reflash your current on onto a clean wipe. if you dont understand how to clean wipe do all of these steps, factory reset, clear cache, clean dalvik cache then go to mounts > storage and format data + format cache + format system
now install new rom and let it boot up, should bootloop a couple of times then start! if not unplug battery from phone and ask for further assitance
Pixelguy said:
1) Attach your phone to the PC via USB (use a port closest to the power supply)
2) Reboot phone while holding volume down until you see "fastboot"
3) Press volume up to initiate fastboot
Click to expand...
Click to collapse
Thank you for your help, the problem is exactly here, i put on the usb, i power up the phone by pressing the volume down, and the phone does nothing,doesn't show the fastboot,and after 10-15 secs starts rebooting again. This is my problem!
The only response from my phone is when powering up, and pressing the volume up, it says "starting rsd protocol support"
Is there any case that my volume down is dead?
ergotelis said:
Thank you for your help, the problem is exactly here, i put on the usb, i power up the phone by pressing the volume down, and the phone does nothing,doesn't show the fastboot,and after 10-15 secs starts rebooting again. This is my problem!
The only response from my phone is when powering up, and pressing the volume up, it says "starting rsd protocol support"
Is there any case that my volume down is dead?
Click to expand...
Click to collapse
unplug usb
remove battery, then put battery back in make sure phone off (no green light)
then hold power button and vol down at the same time for a few seconds
Fastboot should appear in white writing then press up volume and it should say starting rsd protocal or something similiar
then plug in usb and follow the steps i have written above
i do exactly what you said, but doesn't show fastboot. from switched off, if i press volume up with power button, i see the message "starting rsd protocol support" .but no fastboot option!
Is there any chance that you can access adb after bootscreen? than you can use "adb reboot recovery" to get there...
jorno88 said:
Is there any chance that you can access adb after bootscreen? than you can use "adb reboot recovery" to get there...
Click to expand...
Click to collapse
When i start up phone, the only combination possible to stop restarting is by pressing power+vol up to show that with RSD. There is no other option then selectable. Power + volume down does not work, doesn't show anything, has anyone of you experienced this thing?
If the only working option you have is RSD, then I'm afraid you're stuck with having to flash a stock SBF. I hope you know/remember exactly what stock version you had installed before any modding or flashing, because the SBF has to match exactly. Choose wisely and read up as much as you can before flashing.
I have over a year now with custom roms, and i can't remember which version i had. Why do i have to find exactly the version that i had? The latest stock version won't work with rsd? It will make it hard brick?If i manage at least to recover the fastboot menus etc it would be great!
I will later also try to open it, to see if the side button "volume down" is not working,.
I have another question, in your moto atrix, if you press on startup power+vol up, are you also seeing the "starting RSD" etc option??
ergotelis said:
I have over a year now with custom roms, and i can't remember which version i had. Why do i have to find exactly the version that i had? The latest stock version won't work with rsd? It will make it hard brick?If i manage at least to recover the fastboot menus etc it would be great!
Click to expand...
Click to collapse
Yes, flashing a wrong SBF will most likely hardbrick your device.
ergotelis said:
I have another question, in your moto atrix, if you press on startup power+vol up, are you also seeing the "starting RSD" etc option??
Click to expand...
Click to collapse
Can't try right now, but as far as I know, yes, that is a standard way to enter RSD mode.
thank you, so, i know that at least my phone responds to some instructions.
Is there anyone else to suggest me to do anything else?
IN rsd mode, (other than flashing a stock random rom with chance of hardbricking,)the phone can be read by usb, can i do anything there?
ergotelis said:
IN rsd mode, (other than flashing a stock random rom with chance of hardbricking,)the phone can be read by usb, can i do anything there?
Click to expand...
Click to collapse
Sadly no. The RSD mode can only ever be used to flash SBFs. That's it. Nothing less, nothing more.
I will now try to open it to see if vol down is not working well. If it does work, i will select a stock rom 1 year old and i will flash it using rsd, and whatever happens....:good:
I disassembled the phone, the button seems to operate fine(?).
I flashed with RSDlite the 2.3.6 version, the RSD stuck to waiting for phone to restart.
The phone restarted, the "unlocked" logo disappeared.
Starts normally, passes the red motorola logo, shows the graphic of AT&T, and after ~10sec starts restarting again. Bootloop again!
At boot, pressing power+vol up, i can still get the RSD support. Pressing power+vol down does nothing, I don't see any error messages, like the ones in hard brick.
What can i do now, any ideas please!!!
try this
ergotelis said:
I disassembled the phone, the button seems to operate fine(?).
I flashed with RSDlite the 2.3.6 version, the RSD stuck to waiting for phone to restart.
The phone restarted, the "unlocked" logo disappeared.
Starts normally, passes the red motorola logo, shows the graphic of AT&T, and after ~10sec starts restarting again. Bootloop again!
At boot, pressing power+vol up, i can still get the RSD support. Pressing power+vol down does nothing, I don't see any error messages, like the ones in hard brick.
What can i do now, any ideas please!!!
Click to expand...
Click to collapse
Yesterday I had a hard time getting my phone into fastboot mode, after loading a bad SV kernel,it only wanted to start the RSD protocol mode. I eventually got into fastboot by plugging into the wall charger, then removing and installing the battery while holding the vol button. When fastboot appears, unplug the charger to allow sd access.
Thanks for the suggestion, i tried even this,it didn't work. The funny thing is that it shows the battery charging level full screen if i connect the charger, as it starts.
I noticed also that when i press vol down now, it takes longer to start and continue to the moving red logo, it stays for a while stable red,feels like it is thinking whether to start or not lol (if i don't press vol down, on the power up the red moto logo immediately starts the classic "waving" effects)
Anyone having any kind of suggestion?I guess you don't, right?
Hi Guys
I flashed my phone awhile bk with XXELLB/A off sammobile. I have now decided to root my s3. I hold Home,Vol + then power., it enter recovery mode, not download mode and therefore odin isnt picking my phone up. If i boot into android connect my phone up, Odin picks it up etc but obviously am unable to do anything further.
Any suggestions as to what i can do?:crying:
travismailsa said:
Hi Guys
I flashed my phone awhile bk with XXELLB/A off sammobile. I have now decided to root my s3. I hold Home,Vol + then power., it enter recovery mode, not download mode and therefore odin isnt picking my phone up. If i boot into android connect my phone up, Odin picks it up etc but obviously am unable to do anything further.
Any suggestions as to what i can do?:crying:
Click to expand...
Click to collapse
Download mode is Volume down + Power + Home
zoot1 said:
Download mode is Volume down + Power + Home
Click to expand...
Click to collapse
That takes me into some weird "recovery mode" where by odin doesnt read the phone. Not into "download mode"
travismailsa said:
That takes me into some weird "recovery mode" where by odin doesnt read the phone. Not into "download mode"
Click to expand...
Click to collapse
Press volume up once you are in download mode
I'm guessing you didn't read what that "weird" recovery screen said
slaphead20 said:
Press volume up once you are in download mode
I'm guessing you didn't read what that "weird" recovery screen said
Click to expand...
Click to collapse
heres a picture taken with another stock S3 with the same issue.
*image-share.com/upload/2121/298.jpg
add the www as im not allowed to post outside links yet
That is stock recovery, you need volume DOWN/home/power, and keep holding them
travismailsa said:
heres a picture taken with another stock S3 with the same issue.
*image-share.com/upload/2121/298.jpg
add the www as im not allowed to post outside links yet
Click to expand...
Click to collapse
You entering into stock recovery by pressing vol up+Power+home..
You need to press Vol Down+Power+Home..
Check out the videos in this thread if you don't know how to press a button..
http://forum.xda-developers.com/showthread.php?t=1655397&highlight=totallydubbed
Hi i have small problem with my phone my phone is at 4.0.4and i installed newest miui and now my kernel is messed up.
I cant open ap fastboot or any else tool there it results black screen is it possible to restore kernel any other way like trough safestrap?
Is there anywhere original kernel for ics that i could install trough cwm??
Ihmejampah said:
Hi i have small problem with my phone my phone is at 4.0.4and i installed newest miui and now my kernel is messed up.
I cant open ap fastboot or any else tool there it results black screen is it possible to restore kernel any other way like trough safestrap?
Click to expand...
Click to collapse
So you tried to install the MIUIv5 on a ICS based phone? That wasn't very smart as there is clearly stated you must be on 4.1.2!
Usually there is no chance to mess up your kernel by flashing a custom rom - our bootloader is locked which makes things like that more difficult.
It looks like a problem with the bootloader and not a messes up kernel - even when I cannot imagine why this happended because you are using Safestrap! Except you were using an old SS version - there would be no guarantee for potential issues when mixing old stuff with new stuff..
If you cannot enter AP fastboot mode it looks really bad for you... Are you sure you cannot enter fastboot??
Force reboot by pressing and holding Power key + Vol Down key, then immediately press and hold BOTH Vol keys when the screen goes off???
Otherwise when you are still able to enter SS you should be able to switch to your stock slot and boot up your stock rom?
dtrail1 said:
So you tried to install the MIUIv5 on a ICS based phone? That wasn't very smart as there is clearly stated you must be on 4.1.2!
Usually there is no chance to mess up your kernel by flashing a custom rom - our bootloader is locked which makes things like that more difficult.
It looks like a problem with the bootloader and not a messes up kernel - even when I cannot imagine why this happended because you are using Safestrap! Except you were using an old SS version - there would be no guarantee for potential issues when mixing old stuff with new stuff..
If you cannot enter AP fastboot mode it looks really bad for you... Are you sure you cannot enter fastboot??
Force reboot by pressing and holding Power key + Vol Down key, then immediately press and hold BOTH Vol keys when the screen goes off???
Otherwise when you are still able to enter SS you should be able to switch to your stock slot and boot up your stock rom?
Click to expand...
Click to collapse
Yeah the mistake happened when i hastly just downloaded the rom and installed it. Never tought it would harm my phone..
My phone works normaly and boots but fastboot does not work :/
Or could the problem come from exessive use of force shutdown? My power button does not work and oftenly i have to force shutdown to open my screen??
Ihmejampah said:
Yeah the mistake happened when i hastly just downloaded the rom and installed it. Never tought it would harm my phone..
My phone works normaly and boots but fastboot does not work :/
Or could the problem come from exessive use of force shutdown? My power button does not work and oftenly i have to force shutdown to open my screen??
Click to expand...
Click to collapse
I don't have any idea why this happened. But you can test something.
1. From recovery's reboot options select "bootloader".
2. Install BMM app (only the app if you're SS user!), open the BMM rebooter and select bootloader or fastboot (if existing).
3. Use RSD lite and your phones fastboot package. Remove everything from its xml file except the kernel - we need something to flash via fastboot for using purposes without messing up your current system. Plug in your phone while being on main system (booted), wait until your phone is being recognized by the computer and press "flash" in RSD lite. Usually RSD boots your phone into fastboot automatically.
Gesendet von meinem XT910 mit Tapatalk 4
Again small problem what makes this hard i cant select the recoverys reboot options the selecting button is power button and it doesnt work.
Maby i throw phone to service mans face and tell him to fix power button
bigger problem
Ihmejampah said:
Again small problem what makes this hard i cant select the recoverys reboot options the selecting button is power button and it doesnt work.
Maby i throw phone to service mans face and tell him to fix power button
Click to expand...
Click to collapse
I kind of have a bigger problem. Under BMM I played 2 ROMS in KEXEC. I wanted to change the names of the ROMS in BMM but BMM indicated problems and asked to undelete. I did and restarted, but now I cannot enter the phone.
Tried to fastboot under RSD but my fastboot file led to "FAIL".
Ran an old "ubrick routine" which helped me before http://forum.xda-developers.com/showthread.php?p=39247094#post39247094 which booted the phone and keeps booting in the JBX logo
In the meantime I tried a number of old fastboot files but all failed.
http://forum.xda-developers.com/showthread.php?t=2231289 did the trick