flash the phone with the Samsung Galaxy Ace s5830i la fleur
Now, when the writing Logo jpg draw failed
sews all the instructions correctly.
've tried many versions of firmware.After all firmware to issue one (logo jpg draw failed)
Wipe can not do because it does not comes in the mode Recovery.
Smartphone comes only mode (this mode Odin)
driver installed on Usb.Odin Multi Loader using version Odin3 v3.07.
here's the log firmware
Spoiler
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_S5830ZXXLK3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PHONE_S5830iXXLK1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_S5830ZOXELH1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Get PIT for mapping..
<ID:0/011> Firmware update start..
<ID:0/011> boot.img
<ID:0/011> NAND Write Start!!
<ID:0/011> param.lfs
<ID:0/011> sbl.bin
<ID:0/011> system.img
<ID:0/011> userdata.img
<ID:0/011> BcmCP.img
<ID:0/011> Transmission Complete..
<ID:0/011> Now Writing.. Please wait about 2 minutes
<ID:0/011> Receive Response from boot-loader
<ID:0/011> csc.rfs
<ID:0/011> RQT_CLOSE !!
<ID:0/011> RES OK !!
<ID:0/011> Removed!!
<ID:0/011> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
and after that the logo does not appear Samsung Galaxy Ace La Fleur, instead ( ' logo jpg' draw file )
how can it be cured?
Because you install S5830i version on your Ace La Fleur . La Fleur is not appear at bootlogo. Anyway , you phone is normal run. It nothing happen to your phone if you install S5830i version without La Fleur. :fingers-crossed:
HanLand_Ace"I" said:
Because you install S5830i version on your Ace La Fleur . La Fleur is not appear at bootlogo. Anyway , you phone is normal run. It nothing happen to your phone if you install S5830i version without La Fleur. :fingers-crossed:
Click to expand...
Click to collapse
and I do not, so it was La Fleur.
in any version, but gives the same => logo jpg draw failed
logo does not want what is not
Try to flash firmware with pit files...and make sure ur on stock rom...
Sent from my GT-S5830i using xda app-developers app
Angelogc said:
and I do not, so it was La Fleur.
in any version, but gives the same => logo jpg draw failed
logo does not want what is not
Click to expand...
Click to collapse
Try to flash S5830Z firmware.
http://www.hotfile.com/dl/184136306/64dc6a1/S5830ZXXLK3_S5830ZOXELH1_SER.zip.html for ex.
S5830i Stock + Root + init.d + LightSpeed Intervention + Link2SD
ChelebiTech said:
Try to flash S5830Z firmware.
http://www.hotfile.com/dl/184136306/64dc6a1/S5830ZXXLK3_S5830ZOXELH1_SER.zip.html for ex.
S5830i Stock + Root + init.d + LightSpeed Intervention + Link2SD
Click to expand...
Click to collapse
did not help: (
Boot mode Odin .This is what is written.
Odin Mode
PRODUCT NAME: GT-S5830i
CUSTOM BIN DOWN:YES(9 counts)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Mafi91
with cooperve_0623.pit
does not work.
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830ZXXLF3_S5830ZOXELE1_RST_S5830iXXLF2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Set PIT file..
<ID:0/011> DO NOT TURN OFF TARGET!!
<ID:0/011> Get PIT for mapping..
written at the top SET Partition .this inscription over ID:COM
tick in Odin ,stand on Auto Reboot ,Re-Partition,F.Reset Time
sorry for such a great picture. do not know how to clean under the spoiler.
Do not use pit file and dont select repartition. Put firmware under PDA section of odin, not bootloader part.
S5830i Stock + Root + init.d + LightSpeed Intervention + Link2SD
ChelebiTech said:
Do not use pit file and dont select repartition. Put firmware under PDA section of odin, not bootloader part.
S5830i Stock + Root + init.d + LightSpeed Intervention + Link2SD
Click to expand...
Click to collapse
did as you wrote.
here's the log
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830ZXXLK3_S5830ZOXELH1_RST_S5830iXXLK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Added!!
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Get PIT for mapping..
<ID:0/011> Firmware update start..
<ID:0/011> sbl.bin
<ID:0/011> NAND Write Start!!
<ID:0/011> BcmCP.img
<ID:0/011> boot.img
<ID:0/011> system.img
<ID:0/011> param.lfs
<ID:0/011> csc.rfs
<ID:0/011> RQT_CLOSE !!
<ID:0/011> RES OK !!
<ID:0/011> Removed!!
<ID:0/011> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Only when you turn on your phone, a black screen and the inscription.As on the screenshot 1
Nothing has changed.
You need to get full file of stock rom . It must be work . Let i check the La Fleur Ace stock rom
Note:- I have check La fleur version stock ROM , not available . But you must download one by one file S5830i without La Fleur version
Go to this link : Firmware Sammobile
HanLand_Ace"I" said:
You need to get full file of stock rom . It must be work . Let i check the La Fleur Ace stock rom
Note:- I have check La fleur version stock ROM , not available . But you must download one by one file S5830i without La Fleur version
Go to this link : Firmware Sammobile
Click to expand...
Click to collapse
I downloaded
Ukraine 2012 November 2.3.6 S5830ZXXLK3 S5830ZOXELH1
Ukraine 2012 November 2.3.6 S5830IXXLK3 S5830IOXELH1
established. did not help, it is still logo jpg draw failed.
I need to wipe the system. To clear section which stores Boot Skrin.
Pit the file can not do it stupidly vayp.Tak hanging and not what is not there delaet.Skrin above.
in Recovery and does not go for a black screen with a Recovery nadpisyu.Tak that do not wipe out.
Angelogc said:
I downloaded
Ukraine 2012 November 2.3.6 S5830ZXXLK3 S5830ZOXELH1
Ukraine 2012 November 2.3.6 S5830IXXLK3 S5830IOXELH1
established. did not help, it is still logo jpg draw failed.
I need to wipe the system. To clear section which stores Boot Skrin.
Pit the file can not do it stupidly vayp.Tak hanging and not what is not there delaet.Skrin above.
in Recovery and does not go for a black screen with a Recovery nadpisyu.Tak that do not wipe out.
Click to expand...
Click to collapse
Try to flash the attachment in odin, place in Boot selection.
If its not work, try to flash a custom kernel then test if recovery works, then flash stock rom...
Oh ! The custom kernel ! I'm forget ! If it don't work too, send your phone to the Samsung Center Service. Like my phone , i got bricked hard and i want to unbrick my phone , it not working .Another one member is posting the thread is "Download Mode Invisible" for our phone , he post this year .I got bricked it on year 2012 . Now my phone is working because i send it to Samsung Service.
Sorry for my bad english.
ChelebiTech said:
Try to flash the attachment in odin, place in Boot selection.
If its not work, try to flash a custom kernel then test if recovery works, then flash stock rom...
Click to expand...
Click to collapse
did not help: (
Related
hi, i stupidly attempted to root my note (i realise im a bit out of my depth!) watching a youtube guide this one to be specific - CANNOT POSTS LINKS YET!
i didn't do a lot of preperation so wasnt aware what kernal i was on (although the phone is fairly new so possibly ics?) although i do know that im on version 4.0.4 thanks to odin. so i followed the video and attempted both kernals (is this bad for the phone?) one failing and on giving the green light on odin.
afterwards i tried this guide as well - CANNOT POSTS LINKS YET! although not sure how relevant this is because it didnt work after the first attempt.
please can i have a push in the right direction, i am very confused/depressed without my note! i have tried all the restore/format options through recovery mode but at least this means its not bricked if i still have the options right? all that happens when i boot up is the note screen and a yellow triangle. cheers in advance!
That boot screen means download mode. Just reboot your pc, start odin, connect your phone, flash the correct kernel.
You should flash this recovery kernel first:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
from: http://forum.xda-developers.com/showthread.php?p=24505604
Then reboot into recovery and flash a rooted ICS rom.
To do that you will have to go to the development section and find a rom you like and download to your pc, then put your sd card in your pc and move it to your sd card, then put the sd card in your phone. Then you're ready to flash.
rangercaptain said:
That boot screen means download mode. Just reboot your pc, start odin, connect your phone, flash the correct kernel.
You should flash this recovery kernel first:
from: http://forum.xda-developers.com/showthread.php?p=24505604
Then reboot into recovery and flash a rooted ICS rom.
To do that you will have to go to the development section and find a rom you like and download to your pc, then put your sd card in your pc and move it to your sd card, then put the sd card in your phone. Then you're ready to flash.
Click to expand...
Click to collapse
ok, thanks for the quick reply, will give it a go and let you know how it went
ok, this failed :S with the following message
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> cwm-touch-i717-120414.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
did everything right i think, downloaded the link u gave me, opened odin, put the file in pda, pressed the volume up button then start. did i do anything wrong?
cw00 said:
ok, this failed :S with the following message
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
did everything right i think, downloaded the link u gave me, opened odin, put the file in pda, pressed the volume up button then start. did i do anything wrong?
Click to expand...
Click to collapse
Maybe...
Are you using the stock USB cable ?
If so, are you connecting to the rear of the PC using a powered USB port ?
check these two items, then run it again....
If it fails twice, we start looking at a re-download of files, and cleaning of the PC environment....g
gregsarg said:
Maybe...
Are you using the stock USB cable ?
If so, are you connecting to the rear of the PC using a powered USB port ?
check these two items, then run it again....
If it fails twice, we start looking at a re-download of files, and cleaning of the PC environment....g
Click to expand...
Click to collapse
ah maybe thats it, im plugging it in to the front port. give it a go and let you now, cheers for the reply
one other item...
When starting Odin......right click, and "run as administrator"....
this often helps as well....g
ok definatley the stock usb cable, in the back of the pc, new error code
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> cwm-touch-i717-120414.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
what does this mean?
cw00 said:
ok definatley the stock usb cable, in the back of the pc, new error code
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> cwm-touch-i717-120414.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
what does this mean?
Click to expand...
Click to collapse
It means the PC cant open the port you are using....
Lets pick another one....you likely have 4 USB ports on the back, and it doesnt like the one you picked. no biggie, lets try another....g
run as admin trick didn't work either hmm
ok thats all 4 ports, same thing happened... its definatley the correct file?
cwm-touch-i717-120414.tar.md5
cw00 said:
ok thats all 4 ports, same thing happened... its definatley the correct file?
cwm-touch-i717-120414.tar.md5
Click to expand...
Click to collapse
Yep...the file is correct........
and with all 4 ports saying the same thing, I'm gonna have to think about this for a minute or 10..
the front port gave a standard error, and the back ports gave a no connect. So we go back to the front ports, and reboot the PC...
Now from here we have a few choices to make.
Take a break for a few...I have to drive home from work, then i'll be back to help you more..... about 20 minutes.....g
ok thanks for your dedication! its gone 12am here, will try and stay up as long as needs be lol
front two ports with restart:
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> cwm-touch-i717-120414.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> recovery.img
<ID:0/012> NAND Write Start!!
<ID:0/012>
<ID:0/012> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I'm reviewing the .tar file ...
It is likely missing something .on your end ...stand by ...g
---------- Post added at 05:16 PM ---------- Previous post was at 05:11 PM ----------
Okay .....re-download the .tar ....
It may be corrupted ....and be sure to delete the old copy from the PC ....
gregsarg said:
I'm reviewing the .tar file ...
It is likely missing something .on your end ...stand by ...g
---------- Post added at 05:16 PM ---------- Previous post was at 05:11 PM ----------
Okay .....re-download the .tar ....
It may be corrupted ....and be sure to delete the old copy from the PC ....
Click to expand...
Click to collapse
it seems to be stuck on <ID:0/012> SetupConnection..
been like that for a while and no progress
cw00 said:
it seems to be stuck on <ID:0/012> SetupConnection..
been like that for a while and no progress
Click to expand...
Click to collapse
USB connection is failing .....
I'm hoping it's not a driver issue ....
Close and restart Odin ....then try again ....g
yep still stuck on it. hmm is there another kernal i could try. like you said this one may be corrupt
Quick question ..
What antivirus software do you use ?
---------- Post added at 05:41 PM ---------- Previous post was at 05:40 PM ----------
cw00 said:
yep still stuck on it. hmm is there another kernal i could try. like you said this one may be corrupt
Click to expand...
Click to collapse
This is the one you need ...
Did you download it a second time ?
ah tried the other port on the front, this message
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> cwm-touch-i717-120414.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Get PIT for mapping..
<ID:0/011> Firmware update start..
<ID:0/011> recovery.img
<ID:0/011> NAND Write Start!!
<ID:0/011>
<ID:0/011> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
gregsarg said:
Quick question ..
What antivirus software do you use ?
---------- Post added at 05:41 PM ---------- Previous post was at 05:40 PM ----------
This is the one you need ...
Did you download it a second time ?
Click to expand...
Click to collapse
avg, sorry i have to bloody wait 5 minutes every time i post!
Hi everyone,
My S3 stucks on boot logo ,and when i connect it to the charger i have just the grey battery with cirle inside it , no grenn battery after 3 hours.I'd tried several usb cable chargers but nothing. I tried to flash it with odin throught Download mode it always fail after NAND Write Start!! .Even with stock roms or custom ones .and i can't go in recovery mode.
In Odin mode appear like :
PRODUCT NAME :GT-I9300
CUSTOM BINARY DOWNLOAD :YES (7 COUNTS)
SYSTEM STATUT: Custom
Any suggestions Please: tnx:good:
Sounds like nand damage, you can try a rescue firmware & pit:
http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6
But I wouldn't hold out too much hope.
Thank you very much, for your reply..
I'll try this night..
Regards
I followed all the instructions and always the same result No Pit partition ,here is the log :
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300_REV00_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9300XXDLJ4_368423_REV00_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9300XXDLID_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_BTU_I9300OXADLJ4_368423_MULTI_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Any others suggestions PLZ
ID:0/005> There is no PIT partition.
Destroyed PIT requires a service centre paid for repair .
jje
If you added the pit file and ticked repartition then as jje says it needs a new motherboard, sorry.
"GUIDE FOR FLASHING STOCK FIRMWARE"
1-DOWNLOAD STOCK FIRMWARE FROM BELOW LINK (TOTAL 498MB FILE) & EXTRACT IT ON YOUR DESKTOP.
https://docs.google.com/file/d/0B5ETeurHSoZNNUtUaEFXYTBObFU/edit?pli=1
2-DOWNLOAD ODIN FROM BELOW LINK & EXTRACT IT ON YOUR DESKTOP
http://www.mediafire.com/download/772dlmuaxfgm0x2/Odin307.zip
3-Download and Install Moborobo PC Suite from below link It will install Drivers for your phone
http://www.moborobo.com/products/moborobo.html
OR
YOU CAN DOWNLOAD & INSTALL USB DRIVER DIRECTLY FROM BELOW LINK
http://downloadcenter.samsung.com/c...Driver_for_Mobile_Phones_v1.5.23.0-retail.exe
4-NOW FOLLOW BELOW ACTIONS:
1).FIRST CONNECT THE PHONE TO PC IN DOWNLOAD MODE:-
PROCESS FOR DOWNLOAD MODE WRITTEN BELOW
SWITCH OFF YOUR PHONE & PRESS VOLUME DOWN + HOME + POWER TOGETHER YOU LL GET A SCREEN SHOWING WARNING NOW PRESS VOLUME UP IT WILL SHOW YOUR PHONE IS IN DOWNLOADING MODE.
2).THEN OPEN THE ODIN AND YOU LL SEE ID;COM COLOR IN BLUE (IT MEANS PHONE IS CONNECTED).
3).SELECT PDA AND GO TO DESKTOP WHERE YOU HAVE EXTRCTED THAT STOCK FIRMWARE SELECT IT - WAIT FOR CHECKING MD5 TO BE FINISHED CLICK ON START N WAIT FOR 5 MINUTES PHONE WILL BE REBOOT.
DONE YOU HAVE SUCCEFULLY FLASHED STOCK FIRMWARE ON YOUR SAMSUNG GT-S5282.
dashingdwivedi said:
"GUIDE FOR FLASHING STOCK FIRMWARE"
1-DOWNLOAD STOCK FIRMWARE FROM BELOW LINK (TOTAL 498MB FILE) & EXTRACT IT ON YOUR DESKTOP.
https://docs.google.com/file/d/0B5ETeurHSoZNNUtUaEFXYTBObFU/edit?pli=1
Click to expand...
Click to collapse
Thank you for your work, Does it support arabic language as a main language? and is this firmware specific for a country? i mean if i flash it will i have a problem with my network?
Hmmm u can flash other countey s frmware too ... ..nd can select language in setup .....
Its india s frmware.....
Sent from my GT-S5282 using xda premium
Nice work
AdibSul said:
Thank you for your work, Does it support arabic language as a main language? and is this firmware specific for a country? i mean if i flash it will i have a problem with my network?
Click to expand...
Click to collapse
It has saved my phone many times . Thanx bro for ur easy guide.
My phone is from Indonesia. When I flashed this ROM, it ended up with boot loop. Any suggestion?
Wipe user data and cache and then try it
ordinary_laks said:
My phone is from Indonesia. When I flashed this ROM, it ended up with boot loop. Any suggestion?
Click to expand...
Click to collapse
Wipe user data and cache and then try it. Hope it helps. If it doesnt help then try firmware of your country
works like a charm! thanks!
rahulsinghal said:
Wipe user data and cache and then try it. Hope it helps. If it doesnt help then try firmware of your country
Click to expand...
Click to collapse
Hit like button is better than commentinf
Sent from my GT-S5282 using Tapatalk
this is odex or deodex!!!
spidys02 said:
this is odex or deodex!!!
Click to expand...
Click to collapse
Odexed
Remember by name Rahul Singhal , thats enough for me
Odexed dude.
Sent from my GT-S5282 using xda app-developers app
My phone is keep booting will it work for me??
Flashed successfuly but net connection is not turning on
What to do?? Plzz help
stock firmware download
Sir GOOD DAY. can you help me. i downloaded ur stock firmware for 4times and its always says unconfirmed network error. does it mean that the file is no longer there?. thanks a lot.
Flashing Stock Firmware on S5282
Dear Dwivedi,
I tried to flash stock firmware on GT-S5282, by following exactly the steps suggested by you. However I did not succeed as ODIN stuck at "<ID:0/010> NAND Write Start!!" for hours together. I tried the procedure with ODIN 3.09 and 3.10 with different compatible stock ROM but ended with same result. Messages as displayed in the status box of ODIN are as under:
Odin 3.07
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5282XXAMEA_S5282ODDAME5_S5282DDAME2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> SPRDDSP.img
<ID:0/010> NAND Write Start!!
Odin 3.09
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5282XXANA2_S5282ODDANA1_S5282DDAMH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> SingleDownload.
<ID:0/010> SPRDDSP.img
<ID:0/010> NAND Write Start!!
Will be thankful you if you could kindly suggest some way out in this regard. In fact the handset could not be upgraded through KIES and the display now stuck at " try emergency recovery through KIES" with yellow triangle above.
Thanks,
T. Prasad
Need Help!!!!
@dashingdwivedi
i did all the steps as mentioned, once phone rebooted, it has attached error, it's in "Factory Mode", dont know how to remove this, also IMEI no is 0000000000000000, Power button is not working.
Please help
try to flash the stock rom again before doing reset ur device..... it will work
by the way from past two years m not using it anymore
atulsaini_22 said:
@dashingdwivedi
i did all the steps as mentioned, once phone rebooted, it has attached error, it's in "Factory Mode", dont know how to remove this, also IMEI no is 0000000000000000, Power button is not working.
Please help
Click to expand...
Click to collapse
for this issue you can flash pre_rooted_stock firmware provided by @Chirtagh ....it has happend to me also so flashed @Chirtagh's prerooted firmware...
tpsonwani said:
Dear Dwivedi,
I tried to flash stock firmware on GT-S5282, by following exactly the steps suggested by you. However I did not succeed as ODIN stuck at "<ID:0/010> NAND Write Start!!" for hours together. I tried the procedure with ODIN 3.09 and 3.10 with different compatible stock ROM but ended with same result. Messages as displayed in the status box of ODIN are as under:
Odin 3.07
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5282XXAMEA_S5282ODDAME5_S5282DDAME2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> SPRDDSP.img
<ID:0/010> NAND Write Start!!
Odin 3.09
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5282XXANA2_S5282ODDANA1_S5282DDAMH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> SingleDownload.
<ID:0/010> SPRDDSP.img
<ID:0/010> NAND Write Start!!
Will be thankful you if you could kindly suggest some way out in this regard. In fact the handset could not be upgraded through KIES and the display now stuck at " try emergency recovery through KIES" with yellow triangle above.
Thanks,
T. Prasad
Click to expand...
Click to collapse
great. I really need it for my dad's phone.
very very good man very thx
Hi all,i have Galaxy s3 i9300 with problem.The phone open and i see on the screen only this (Samsung galaxy s3 i9300) and 10 seconds after i see the samsung logo.The phone enter normal in download mode and i flash one rom with odin but i see this message on odin.
<ID:0/019> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGMK6_I9300OXXGML1_I9300XXUGMK6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/019> Odin v.3 engine (ID:19)..
<ID:0/019> File analysis..
<ID:0/019> SetupConnection..
<ID:0/019> Initialzation..
<ID:0/019> Get PIT for mapping..
<ID:0/019> Firmware update start..
<ID:0/019> boot.img
<ID:0/019> NAND Write Start!!
<ID:0/019>
<ID:0/019> Complete(Write) operation failed.
<ID:0/019> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I flash 4-5 roms but i see the same
Please help !!!
Can you reboot into recovery and flash another ROM ?
Andr3y29 said:
Can you reboot into recovery and flash another ROM ?
Click to expand...
Click to collapse
no entered in recovery mode..the phone is rooted
emmc is either corrupt or damaged, try the rescue firmware from general forum else new motherboard.
boomboomer said:
emmc is either corrupt or damaged, try the rescue firmware from general forum else new motherboard.
Click to expand...
Click to collapse
what is the general forum ?
Any idea ?i see this message on ODIN
<ID:0/019> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGMK6_I9300OXXGML1_I9300XXUGMK6_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/019> Odin v.3 engine (ID:19)..
<ID:0/019> File analysis..
<ID:0/019> SetupConnection..
<ID:0/019> Initialzation..
<ID:0/019> Get PIT for mapping..
<ID:0/019> Firmware update start..
<ID:0/019> boot.img
<ID:0/019> NAND Write Start!!
<ID:0/019>
<ID:0/019> Complete(Write) operation failed.
<ID:0/019> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Try reading the answer you were given, if it doesn't work then pay for a repair/new phone.
Sent from my GT-I9300 using Tapatalk
hi
Iam in 4.3 i want to flash Odin rom 4.3 To refresh my rom when i do it i see this
PHP:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXUGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXUGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9300XXUGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9300XXUGMJ9_1902166_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
then i try to do a CF Root with this file : CF-Auto-Root-d2spr-d2spr-sphl710
and i can disable the knox
i try to enter the recovery mode but it show me black screen ،، i try i lot of recovery's but problem is still
thanks and i hope found a good help
ahmedsaber20005 said:
hi
Iam in 4.3 i want to flash Odin rom 4.3 To refresh my rom when i do it i see this
then i try to do a CF Root with this file : CF-Auto-Root-d2spr-d2spr-sphl710
and i can disable the knox
i try to enter the recovery mode but it show me black screen ،، i try i lot of recovery's but problem is still
thanks and i hope found a good help
Click to expand...
Click to collapse
Nand write fail usually means Nand is corrupt flash this recovery firmware >> http://forum.xda-developers.com/showpost.php?p=30087735 << if that fails service repair new motherboard required.
Also there is no knox in 19300
tallman43 said:
Nand write fail usually means Nand is corrupt flash this recovery firmware >> http://forum.xda-developers.com/showpost.php?p=30087735 << if that fails service repair new motherboard required.
Also there is no knox in 19300
Click to expand...
Click to collapse
my phone is live but not able to take a new firmware ،، i try this I9300XXUGNA7_I9300OJVGNA1_XSG (( one file ))
and this (( GT-I9300XXUGMJ9 4.3 )) 4 files} and i see this
PHP:
<ID:0/004> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGNA7_I9300OJVGNA1_I9300XXUGMK6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
i will try your firmware you but the link put it it supported Arabic UI ?? >>>>4.3
GT-I9300XXUGMJ9_KOR_MULTI_FACTORY
ahmedsaber20005 said:
my phone is live but not able to take a new firmware ،، i try this I9300XXUGNA7_I9300OJVGNA1_XSG (( one file ))
and this (( GT-I9300XXUGMJ9 4.3 )) 4 files} and i see this
i will try your firmware you but the link put it it supported Arabic UI ?? >>>>4.3
GT-I9300XXUGMJ9_KOR_MULTI_FACTORY
Click to expand...
Click to collapse
Sorry when you say is live do you mean you can boot up ok and that you just have problems installing a new rom? If that is the case do not use the emergency firmware it is only to be used as a last resort if you can't boot your rom...
tallman43 said:
Sorry when you say is live do you mean you can boot up ok and that you just have problems installing a new rom? If that is the case do not use the emergency firmware it is only to be used as a last resort if you can't boot your rom...
Click to expand...
Click to collapse
yes i can boot to my phone but recovery not working and i cant install any new Firmware
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
ahmedsaber20005 said:
Click to expand...
Click to collapse
What phone have you got your picture shows you have a SGH-1747 this is the 19300 forum flashing anything from here to your phone can seriously damage it.
Edit
Looks like you have been trying to flash 19300 firmware on your SGH-1747
tallman43 said:
What phone have you got your picture shows you have a SGH-1747 this is the 19300 forum flashing anything from here to your phone can seriously damage it.
Edit
Looks like you have been trying to flash 19300 firmware on your SGH-1747
Click to expand...
Click to collapse
Yes I noticed that and I was just at startup writes ،،، i want the stock image (( kernel )) can you give me a one? because now i flesh kernel for i9300 and it is not boot to system :crying:
ahmedsaber20005 said:
Yes I noticed that and I was just at startup writes ،،، i want the stock image (( kernel )) can you give me a one? because now i flesh kernel for i9300 and it is not boot to system :crying:
Click to expand...
Click to collapse
Sorry to hear that..[emoji33]
I'm not at my computer now but ask in the SGH1747 thread and see if they have some sought of rescue firmware like we do [emoji106]
tallman43 said:
Sorry to hear that..[emoji33]
I'm not at my computer now but ask in the SGH1747 thread and see if they have some sought of rescue firmware like we do [emoji106]
Click to expand...
Click to collapse
thanks ،،، i will do
I flash cm11 and all is OK