hello everyone
I have samsung galaxy ace gt-s5830i. and it had crashed and only what can i see is Samsung logo running again and again in a loop.
I tried to do factory reset from recovery mood but it didn't work, even i tried to setup new firmware by using Odin and it dint work too.
please advice if anyone have a solution for my issue ill be very thankful.
bootloop
ah2mhm said:
hello everyone
I have samsung galaxy ace gt-s5830i. and it had crashed and only what can i see is Samsung logo running again and again in a loop.
I tried to do factory reset from recovery mood but it didn't work, even i tried to setup new firmware by using Odin and it dint work too.
please advice if anyone have a solution for my issue ill be very thankful.
Click to expand...
Click to collapse
hey ur cell is is bootlooping.... try to wipe all. then try to flash stock firmware via odin. and again wipe all.. it works..
lpradol said:
hey ur cell is is bootlooping.... try to wipe all. then try to flash stock firmware via odin. and again wipe all.. it works..
Click to expand...
Click to collapse
I tried already, it is not able even to wipe!! when i apply "wipe data/factory reset" from the recovery list sometimes hang and hold the screen and other times keep restarting and gives me Samsung Galaxy Ace GT-S5830i logo.
And when I use Odin3 v3.07 to install new stock firmware it gives me the following and the same result again, keep restarting and gives me Samsung Galaxy Ace GT-S5830i logo without any success
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830iXXMC1_S5830iOXXLL1_RST_S5830iXXMB2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> BcmCP.img
<ID:0/003> boot.img
<ID:0/003> system.img
<ID:0/003> param.lfs
<ID:0/003> csc.rfs
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/004> Removed!!
<ID:0/004> Removed!!
<ID:0/004> Removed!!
<ID:0/004> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
??
ah2mhm said:
I tried already, it is not able even to wipe!! when i apply "wipe data/factory reset" from the recovery list sometimes hang and hold the screen and other times keep restarting and gives me Samsung Galaxy Ace GT-S5830i logo.
And when I use Odin3 v3.07 to install new stock firmware it gives me the following and the same result again, keep restarting and gives me Samsung Galaxy Ace GT-S5830i logo without any success
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830iXXMC1_S5830iOXXLL1_RST_S5830iXXMB2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> BcmCP.img
<ID:0/003> boot.img
<ID:0/003> system.img
<ID:0/003> param.lfs
<ID:0/003> csc.rfs
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/004> Removed!!
<ID:0/004> Removed!!
<ID:0/004> Removed!!
<ID:0/004> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
are you tried nandroid restore...
ah2mhm said:
I tried already, it is not able even to wipe!! when i apply "wipe data/factory reset" from the recovery list sometimes hang and hold the screen and other times keep restarting and gives me Samsung Galaxy Ace GT-S5830i logo.
Click to expand...
Click to collapse
man use the pit file while flashing...and tick re-partition !!
pit file is in odin folder
Sent from my GT-S5830i using xda app-developers app
nothing work
lpradol said:
are you tried nandroid restore...
Click to expand...
Click to collapse
please, can you tell me how to use Android restore?
nothing work too
srt99 said:
man use the pit file while flashing...and tick re-partition !!
pit file is in odin folder
Sent from my GT-S5830i using xda app-developers app
Click to expand...
Click to collapse
thanks for advice man, I tried but nothing work too, its the same result.
please advice if there is another way?
ah2mhm said:
thanks for advice man, I tried but nothing work too, its the same result.
please advice if there is another way?
Click to expand...
Click to collapse
Use odin v1.84
Use multi pakage firmware
Use pit file hope it will solve :fingers-crossed::laugh:
go into recovery then factory data reset again and clear your cache partition. If you have CWM recovery than also wipe your dalvik cache. another thing you might want to try is to take out the battery for 30 secs than re-insert it. take out the SIM card and the micro SD card as well. If all of those do not work than maybe look for more threads like this or Google your problem. oh I just got another idea when you go into recovery mode and select reboot device look at the bottom to see log information and than Google that problem. I will be honest with you your not the only one which has/d the same problem...one day I was playing a game called 'vector' and when I opened it up it came up with a sign saying that the game used arcitecture ARM7 and Ace-i is arcitecture ARM6. It also said tat it was likely to crash but I played It anyway. I had played It for along while and got really far but one time I had completed another level (I was at school at the time) and the screen went black so I got the screen active again and did my lock screen pattern but it just froze there for a really long time than the screen blacked out for no reason again and BAM im in a bootloop... my mum had eventually found out and the problem so with out me knowing she sent it back to the repair center even though I could have flashed a stock ROM via Odin! (It was under warranty thankfully)
Related
First, I know you are going to ask me to search threads started by other people. I did.
And almost every single one of them wanted me to go to "download mode". The problem is I cant go into download mode no matter how long i pressed the 3 button combination.
So, I tried to root my Samsung Galaxy SII, and things got out of control. It went to "Firmware upgrade encountered an issue..."
I've tried other methods in the forums too, and nothing works. Flashing firmwares dont work for me too.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9100_SIN_I9100DXLP9_I9100OLBLP9_I9100DXLP9.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
Can anyone help me?
chipzx said:
First, I know you are going to ask me to search threads started by other people. I did.
And almost every single one of them wanted me to go to "download mode". The problem is I cant go into download mode no matter how long i pressed the 3 button combination.
So, I tried to root my Samsung Galaxy SII, and things got out of control. It went to "Firmware upgrade encountered an issue..."
I've tried other methods in the forums too, and nothing works. Flashing firmwares dont work for me too.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9100_SIN_I9100DXLP9_I9100OLBLP9_I9100DXLP9.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
Can anyone help me?
Click to expand...
Click to collapse
I had the Exact same problem as you this is what you need to do.
1. Take everything out of your phone micro sd ,sim battery disable kies process as well
2.Get your Usb Port and connect the first side to your pc but not to the phone
3.Insert Battery
4.Hold the vol down butt and at the same time connect the Other side of the cable into the phone then you will see
DOWNLOAD MODE!!!!!
5.From there install your stock rom again using samfirmware.com
6.Done
For 2 minutes it worked, then this came out
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.img
<ID:0/003> NAND Write Start!!
<ID:0/003> factoryfs.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Is it just because my phone has low battery?
THANKS, IT WORKED
Have been fixing it for one whole day, THANKS!!!
custom kernel
chipzx said:
For 2 minutes it worked, then this came out
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.img
<ID:0/003> NAND Write Start!!
<ID:0/003> factoryfs.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Is it just because my phone has low battery?
Click to expand...
Click to collapse
Why don't you install custom kernel..
Go gokhanmoral.com then download latest S2 4.1+ for ICS and JB...
mizzeeboy said:
I had the Exact same problem as you this is what you need to do.
1. Take everything out of your phone micro sd ,sim battery disable kies process as well
2.Get your Usb Port and connect the first side to your pc but not to the phone
3.Insert Battery
4.Hold the vol down butt and at the same time connect the Other side of the cable into the phone then you will see
DOWNLOAD MODE!!!!!
5.From there install your stock rom again using samfirmware.com
6.Done
Click to expand...
Click to collapse
you are GOD!!!
my galaxy s2 is working again, not anymore a dummy
thanks
eheheh said:
you are GOD!!!
my galaxy s2 is working again, not anymore a dummy
thanks
Click to expand...
Click to collapse
glad to help
Hi all,
I have a Samsung Galaxy S3 with a default ROM, rooted and with clockworkmod installed.
Yesterday night I let it charging and working fine. This morning was freezed on the startup screen, the one that says "Samsung Galaxy SIII GT-I93000" and was not possible to go over it. I checked for similar posts in the forum but no one had the same characteristics, all could go further the starting screen.
I tried the next:
- Normal restart: Nothing, same screen
- Take out the battery: Nothing, same screen
- Try to enter in recovery mode (power+home+vol up): Nothing, same screen
- Try to enter in download mode (power+home+vol down): Success, i'm download mode.
What can I do now? there is any chance to enter without re-installing rom and wiping the whole content?
Please, any help is welcome. I'm without mobile meanwhile
Thank you in advance
If the phone does not start in normal mode and recovery mode but it starts in download mode, try to flash a rom Samsung not wipe, if it fails to start still not done with the full wipe rom SAMSUNG
AndroidGaalaxy said:
If the phone does not start in normal mode and recovery mode but it starts in download mode, try to flash a rom Samsung not wipe, if it fails to start still not done with the full wipe rom SAMSUNG
Click to expand...
Click to collapse
Hi, thank you for the fast answer.
I just found the original stock image that i had:
Country/Carrier: Poland (Play)
Date:2012 July
Android: 4.0.4
PDA:I9300XXBLFB
CSC:I9300PRTBLG1
I will turn the phone in download mode and I will connect with Odin.
Sorry about the newbie question: How I flash a new ROM on the phone without wiping all?
Best Regards
Hi,
I try to install flash again the stock ROM and I got this message in Odin.
Code:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLFB_I9300PRTBLG1_I9300XXLFB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007>
<ID:0/007> There is no PIT partition.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I found another post with the same problem: http://forum.xda-developers.com/showpost.php?p=30060308&postcount=23
I tried to restore a PIT file but is failing the whole time
At the end the user told that he brought it to a Samsung service and they changed the "charging regulator" and now the phone is working. :http://forum.xda-developers.com/showpost.php?p=31105754&postcount=34
I don't have any service shop here were I live
Any other idea that I could try?
Thank you in advance
lastminuteproject said:
Hi,
I try to install flash again the stock ROM and I got this message in Odin.
Code:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLFB_I9300PRTBLG1_I9300XXLFB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007>
<ID:0/007> There is no PIT partition.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I'm totally lost now.
any idea?
Thank you in advance
Click to expand...
Click to collapse
Firm Odin, unplugged the USB cable
Open Odin again Selects the file
restart again the phone to download
replug USB cable and try again
And if it still does not try to flash a recovery and tried to boot into recovery mode
lastminuteproject said:
Hi,
I try to install flash again the stock ROM and I got this message in Odin.
Code:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLFB_I9300PRTBLG1_I9300XXLFB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007>
<ID:0/007> There is no PIT partition.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I'm totally lost now.
any idea?
Thank you in advance
Click to expand...
Click to collapse
Did you try to install a .pit file?
RoelVB said:
Did you try to install a .pit file?
Click to expand...
Click to collapse
This is what causes problem apparently...
Hi
I tried several different PIT files and I always get the same message in Odin:
Code:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007>
<ID:0/007> Re-Partition operation failed.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
@AndroidGaalaxy: I can't enter in recovery mode, just in download mode
I don't know what else to try, please help, some other ideas?
lastminuteproject said:
Hi
I tried several different PIT files and I always get the same message in Odin:
Code:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007>
<ID:0/007> Re-Partition operation failed.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
@AndroidGaalaxy: I can't enter in recovery mode, just in download mode
I don't know what else to try, please help, some other ideas?
Click to expand...
Click to collapse
Try to flash a ROM Samsung Jelly Bean (They Do Requires PDA only normally) and do not put anything in pit
Personally I no longer believe too
Yeah Im having the same problem...
apparently the chip that stores boot got non-functional data or something...missed-up in other words
anyhow...from several threads I looked up,,,,only 2 things can solve this , either Jtag repair the phone (check google) or service the phone, but if the flash counter shows in download mode they might not do it on warranty...
my phone has been in service for 3 days now, still didn't tell me if they'll service on warranty or not, luckily I used triangle reset before, everything shows as official samsung except custom rom.
Thank you for the replies.
Regarding bringing it to the service, I have another small issue. I got my mobile in PL. A friend wanted an internet contract there and with that contract the phone was really cheap, so I pay the phone and he kept the SIM....and I live in Germany
I will try to bring it to any shop, let's see what they tell me.
Another question now: I had an original stock ROM, but I just root it to be able to make full backups. They can realize about this entering just in download mode? Is normal that I see "Odin Mode" when I enter in download mode?
Thank you all
lastminuteproject said:
Thank you for the replies.
Regarding bringing it to the service, I have another small issue. I got my mobile in PL. A friend wanted an internet contract there and with that contract the phone was really cheap, so I pay the phone and he kept the SIM....and I live in Germany
I will try to bring it to any shop, let's see what they tell me.
Another question now: I had an original stock ROM, but I just root it to be able to make full backups. They can realize about this entering just in download mode? Is normal that I see "Odin Mode" when I enter in download mode?
Thank you all
Click to expand...
Click to collapse
Download mode is already integrated in the smartphone by cons they may know that you have changed the phone because this flash counter in download mode they would have had to turn away a triangle reset the counter but hey it is not possible because you can not start the phone
Download Mode
AndroidGaalaxy said:
Download mode is already integrated in the smartphone by cons they may know that you have changed the phone because this flash counter in download mode they would have had to turn away a triangle reset the counter but hey it is not possible because you can not start the phone
Click to expand...
Click to collapse
In my situation, my S3 is in download mode but the computer can not see it through a com (up-to-date Odin and Kies can not see my GS3). What should I do?
Messing with PIT maybee ruined your phone.
If it s in warranty maybee they flash it for you. I´ve experienced that before with no problems but I know that it voyds the warranty flashing PIT and rooting.
Maybee you re lucky in the samsung service, in your position I was that way. Jtag is very risky and voyds warranty forever. If you pay in samsung for the boot repair you continue to have your warranty again and for the price of a Jtag intervention I would pay a bit more and continue having warranty.
S3 frozen on boot screen while rooting
Hello everyone,
I'm new around here and i apologize if posting in the wrong place....
I have a similar problem: I decided to root my S3 (UK unlocked) and followed one of many tutorials on YouTube (made by galaxys3root). Everything seemed to be easy and started well until at the point when the S3 must reboot. At that point the phone got stuck, and the only thing i can do is to go in downloading mode.
Odin gives me this
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
<ID:0/003> param.bin
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
While the phone is stuck on the boot screen my PC (Win 7 Ultimate) does not recognize the device, while if the phone is in downloading mode, the PC has the driver for it.
I went through a few more topics on this forum which described something similar, tried a few of the suggestions made by others but nothing seems to work.
Does anyone has a solution for this or I should take the phone in service?
I would appreciate any advise!
I'm quite the beginner so if you could use a technical "friendly" language it would be great
Coming from LiquidSmooth 2.9
Ran triangleaway, then went into download mode, and flashed
KIES_HOME_I9300XXEMG4_I9300OXAEMG4_1314436_REV00_user_low_ship.tar.md5
Odin reported:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I9300XXEMG4_I9300OXAEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> modem.bin
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> sboot.bin
<ID:0/003> tz.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
Click to expand...
Click to collapse
Phone rebooted and now I'm just getting the Samsung logo continuously..
Power on, swirly logo, SAMSUNG, swirly logo, SAMSUNG etc..
Help Please.
How do I get this back to stock ?
Thanks
Basic faqs and guides .
http://forum.xda-developers.com/showthread.php?t=2344125
Critical you read the first two posts .
Probable fail to wipe phone .
Factory reset flash rom again
JJEgan said:
Basic faqs and guides .
http://forum.xda-developers.com/showthread.php?t=2344125
Critical you read the first two posts .
Probable fail to wipe phone .
Factory reset flash rom again
Click to expand...
Click to collapse
Thanks
Obviously should have read this before I started.
Can you advise the best way forward now. ?
Do I try again using Odin and the same file ?
Thanks
Probably should mention I was following this guide:
[Tut] Unroot the Galaxy SIII (for stock updates/warranty)
I would try flashing recovery and then wiping the phone .
JJEgan said:
I would try flashing recovery and then wiping the phone .
Click to expand...
Click to collapse
I managed to get into recovery and that told me it applied BTU.
I've cleared the data/factory reset and cache.
Phone has rebooted and now it appears to have loaded
Thanks
Hi everyone,
I'm having a great problem. Recently got rooted SIII with CF-CWM and ICS Rom. I tried to install recent update of official 4.3 announced for UK (BTU) downloaded from SamMobile.
I used ODIN 3.7 for this process. All went successfully. ODIN automatically did a factory reset but after reset phone is on Samsung logo. Logo and LED light are blinking but not going any further. And I'm unable to go into recovery as well.
Please someone help me out in this matter. I searched here but found nothing relevant. And by the way I'm in Pakistan.
Here is the log of ODIN:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGMJ9_I9300OXAGMJ9_I9300XXUGMJ9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> tz.img
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> modem.bin
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Odin does not do factory reset, boot into recovery and do it again.
Sent from my GT-I9300 using Tapatalk
boomboomer said:
Odin does not do factory reset, boot into recovery and do it again.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
thanks a lot brother
my problem is resolved.
please tell me how can I close this thread now?
How to root?
one more things.
Please guide me will the CF-Auto Root for SIII v6.4 by ChainFire work with 4.3 stock rom or not?
Check out CF's thread, I'm sure it will.
CF's Thread?
boomboomer said:
Check out CF's thread, I'm sure it will.
Click to expand...
Click to collapse
Would you like to tell me which one is CF's thread? any link for that?
faakher said:
Would you like to tell me which one is CF's thread? any link for that?
Click to expand...
Click to collapse
In development or found via the faqs and guides .
I have a Samsung Galaxy S2 i9100G model which was running Cyanogenmod Kitkat version. I wanted to get it on stock firmware. So I downloaded the stock Indian firmware (I9100GDDLS3_I9100GODDLS3_INU) and via ODIN flashed the PD file. Everything went fine according to ODIN but now my phone is just rebooting with the Samsung logo. Can anyone help me what went wrong here? Here is the details of Odin process.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GDDLS3_I9100GODDLS3_I9100GDDLS2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> MLO
<ID:0/003> NAND Write Start!!
<ID:0/003> factoryfs.img
<ID:0/003> param.lfs
<ID:0/003> Sbl.bin
<ID:0/003> zImage
<ID:0/003> modem.bin
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
choosymoron said:
I have a Samsung Galaxy S2 i9100G model which was running Cyanogenmod Kitkat version. I wanted to get it on stock firmware. So I downloaded the stock Indian firmware (I9100GDDLS3_I9100GODDLS3_INU) and via ODIN flashed the PD file. Everything went fine according to ODIN but now my phone is just rebooting with the Samsung logo. Can anyone help me what went wrong here? Here is the details of Odin process.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GDDLS3_I9100GODDLS3_I9100GDDLS2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> MLO
<ID:0/003> NAND Write Start!!
<ID:0/003> factoryfs.img
<ID:0/003> param.lfs
<ID:0/003> Sbl.bin
<ID:0/003> zImage
<ID:0/003> modem.bin
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
Just reboot to stock recovery and wipe data (factory reset) and wipe cache, and the phone will boot fine
MigoMujahid said:
Just reboot to stock recovery and wipe data (factory reset) and wipe cache, and the phone will boot fine
Click to expand...
Click to collapse
Yeah I guess that's the step missing, I will do that the only issue is my HOME button is not working right now will get it repaired and then try the same. Thanks for the reply.
Yeah booted my phone properly into stock. So for anyone who will be stuck in future and would be wondering what to do.. Wiping the data and clearing the cache is the way to go.
Thanks for the help.
greetings. this did not work for me. iv tried to wipe data and wipe cache, and even reflashed the sgs2 but nothing happened. i tried a suggestion in another forum to flash a custom recovery so that i could also wipe the dalvik cache but nothing changed. i can go into recovery just fine and i can install a custom rom as long as the zip file is in the phone memory but not on an external sd card. please help