Hi All
I really hope one of you can help me..
i tried this:
http://forum.xda-developers.com/showthread.php?t=2249077&page=1
My bootloader is unlocked.
So i flashed the ICS kernel, ThP via the command: fastboot flash boot kernel-unsigned.elf
It gave the result: (bootloader) Flash operation complete
But then this step came: Flash the zip and power off the device from recovery
I thought that i needed to reboot my phone, and go into the startup mode i used to have on my CM10.1, so I turned off the phone..
But no boot at all now, and when i try to go into flash mode, nothing happens Only when i prest both the power + vol. up the diode light becomes purple for a short time, but it turns off Again, and my pc dont see the phone, not even a "Windows got a new usb device" sound comes
What do I do now? Is there anyway to bring it back to life?
I really hope someone can help
Kind regards
Juel
Uhh an update, after holding all buttons in several secunds, it vibrates 3 times, and now i can get it in to flash mode..
So ill try a FreeXperia rom and see if it Works..
wardly antatura
TADAA Its working Again, i used Sony's Emma program..
Bro, as much as i see you refer to posts regarding Xperia P, not Go - thats why your phone has been bricked. Read carefully next time.
I made a HUGE thread on getting my xGO rooted. It may not be what you're looking for, but read up on my adventure, it may help you if you get lost or messed up just in case
Related
Hey, I know this is not correct place for Xperia X10 issue's, but i need to display it in general section, as this one is getting critical..
I uploaded a custom rom on my xperia x10, for that i unlockd the bootloader and stuff..
Now, my phone is switched off since 15 days, when ever i try to switch it on, it vibrates once and nothing at all afterwards...if i press power button again, it won't vibrate, unless and untill i remove the battery and reinsert it in phone..
i see three red flashes of light, when connected to PC..
1. PC Companion for update, repair and custom repair is not working...most of the time phone is not detected..
2. SE-update service is also not working and phone is shown as Xperia arc..
3. Flashtool, doesn't recognize the handset
4. few, technician told me box flash would work, but again, it didn't work out
Now, i don't know much about this, but i do understand that hardware seems to be good, till now, the only issue is software and that to initial boot process i.e. bootloader.
is there any other way i can upload a new custom rom on my xperia ??
or any other solution, will be appreciated..
I'm assuming download mode didn't work? Pull battery and insert cord/battery/press back button at same time while aytempting to flash through flashtools?
I have tried flash tools with this method, but doesn't helps..
I don't know about download mode, is it the same done through PC companion..
Thanks
icenight89 said:
I'm assuming download mode didn't work? Pull battery and insert cord/battery/press back button at same time while aytempting to flash through flashtools?
Click to expand...
Click to collapse
I had the xact same problem and this worked for me..THANKS A LOT..i owe you one
Same issue
I have a similar issue.
When I try to flash it through flashtool, I get this error
"ERROR - ERR_SEVERITY="MAJOR";ERR_CLASS="SECURITY_CLASS";ERR_DYNAMIC="SIN header verification failed""
Plus the phone is not also going in the recovery mode.
Please please help me.
Guys, i was upgrading the ROM but this time i used this software, UNIFLASH , it showed some cmd windows, later phone automatically booted to cwm, and then turned off! since then its not turning on neither blinking any LED! guys, please show me a ray , help me! phone is not getting recognized by flashtool either :'( and same with seus
try to hold down power + volume up at the same time until you get the phone to vibrate 3 times, after that try to boot or get it into flashmode with flashtool..
remember.. flashtool is the way to go !
kindly report back or even pm me
realfelix said:
try to hold down power + volume up at the same time until you get the phone to vibrate 3 times, after that try to boot or get it into flashmode with flashtool..
remember.. flashtool is the way to go !
kindly report back or even pm me
Click to expand...
Click to collapse
already tried that, googled a lot already, nothing is helping!
also tried doing what you said with USB connected through my pc, windows kept playing that system sound which comes up when we plus out a device! in particular time intervals, like 3 4 seconds.
bhuvangaur said:
already tried that, googled a lot already, nothing is helping!
also tried doing what you said with USB connected through my pc, windows kept playing that system sound which comes up when we plus out a device! in particular time intervals, like 3 4 seconds.
Click to expand...
Click to collapse
have you tried the fastboot method, it´s in android development, "all you need to know..."
try to flash official stock fw like .452 or .45 with flashtool..try to connect the phone in flashmode....hopefully everything will be alright...
PEACE
guys, phone is not able to boot in any mode, it be fastboot or flashmode! its completely dead thats what i meant earlier. After a lot of researching the whole night, i was able to figure out that the bootloader is that the UNIFLASH corrupted the bootloader. So how to fix that?
try this: make sure you have enough charge and the drivers of your phone are installed correctly. (flashtool drivers)
power+volume up wait till vibrates three times,
then connect your phone to pc.
run the flashtool and prepare the firmwares youre going to flash,
a screen will appear and says turn off your phone....etc
hold power button + volume up wait till vibrates three times
then quickly hold power button + volume down.
it will flash the firmware.
just keep on trying.
mharckk said:
try this: make sure you have enough charge and the drivers of your phone are installed correctly. (flashtool drivers)
power+volume up wait till vibrates three times,
then connect your phone to pc.
run the flashtool and prepare the firmwares youre going to flash,
a screen will appear and says turn off your phone....etc
hold power button + volume up wait till vibrates three times
then quickly hold power button + volume down.
it will flash the firmware.
just keep on trying.
Click to expand...
Click to collapse
its simply not vibrating! i held that combination for like 5 minutes continuous last night, phone has to enter either fastboot or flashmode for flashtool to detect! none of them is coming up, and no LED again when its on charging. complete dead complete mess!
By the way, anyone knows how service center people update the phone's software?
bhuvangaur said:
its simply not vibrating! i held that combination for like 5 minutes continuous last night, phone has to enter either fastboot or flashmode for flashtool to detect! none of them is coming up, and no LED again when its on charging. complete dead complete mess!
By the way, anyone knows how service center people update the phone's software?
Click to expand...
Click to collapse
Go to repair center or phone shop! These guys know how to rewrite ur bootloader through JTAG! Don't worry, u'll get it back once it's done!
Sent From my Lt26i, Hit thank whenever u like!
I think you hard bricked your device... Go to service centre ...
Sent from my LT22i using xda premium
i appreciate you guys for your replies! gave the phone to them yesterday, good to hear about JTAG, will surely revert here and let ya'll know about it! this might happen with any one in future, might help him too!
PS, since the company is no more ericsson based, new service center are SONY one only, where all sony products are welcomed, really good service center now! earlier it was sh*tty since years! i loved the experience this time
bhuvangaur said:
i appreciate you guys for your replies! gave the phone to them yesterday, good to hear about JTAG, will surely revert here and let ya'll know about it! this might happen with any one in future, might help him too!
Click to expand...
Click to collapse
would you please enplane what is JTAG and how it works ?
Had the same problem yesterday!
Maybe a noob advice but here what was my mistake: after switch off the phone with volume up, wait for like 30 second before trying to connect in flash mode. Though my phone was dead but just had to wait a little bit before trying the flash mode. Flashtool heal it!
Sorry for my poor english, I'm french and this is my first post, but I follow xda since a long time!
Bye!
Napolee said:
would you please enplane what is JTAG and how it works ?
Click to expand...
Click to collapse
It a type of connector that is use to connect directly to the phone mainboard. It use to transfer some specific data such as bootloader!
Sent From my Lt26i, Hit thank whenever u like!
this is hilarious!!! a replacement! brand new xperia s! yay!
Trying to Survive my LT26i
I have rooted my phone
put recovery and flashed my rom to xxperience
so everything was ok
using for 2days
so i saw how to overclocked to 1.8ghz and flash via cwm the kernel
after restart from cwm not either the screen turn on
just green light when i put cable on
and when i tried to flash via flash tool given error for error
so i done as say here to hold power + volume up, and the same
so i waited for a little time and try again and its flashing now...
hope it works
Hey guys!
I'm not allowed to post this into the development section for the xperia p, so I have to do it here.
I've decided to root my xperia p. So, I unlocked the bootloader and rooted my device following these instructions using flashtool method: http://forum.xda-developers.com/showthread.php?t=1900172. Right after that, I flashed over this kernel: http://forum.xda-developers.com/showthread.php?t=1894463.
I was pretty happy with this setup until I realised, that this kernel still has some bugs that need fixing and is not ready for stable everyday-use. (In my opinion..)
What I did next was flashing back to the stock kernel, which can be found in the same thread in the first post (for people who want stock kernel with custom CWM) and now my p is in a constant bootloop, turning on and off, without showing any logo and not giving me any access to recovery. I can't even initiate fastboot.. WHAT DO I DO NOW? I really need your help with this..
AND by the way, I have a lot of experience in the matter of flashing and android development, but this is the first time I really don't know what to do to fix this issue!
ace.infinity said:
Hey guys!
I'm not allowed to post this into the development section for the xperia p, so I have to do it here.
I've decided to root my xperia p. So, I unlocked the bootloader and rooted my device following these instructions using flashtool method: http://forum.xda-developers.com/showthread.php?t=1900172. Right after that, I flashed over this kernel: http://forum.xda-developers.com/showthread.php?t=1894463.
I was pretty happy with this setup until I realised, that this kernel still has some bugs that need fixing and is not ready for stable everyday-use. (In my opinion..)
What I did next was flashing back to the stock kernel, which can be found in the same thread in the first post (for people who want stock kernel with custom CWM) and now my p is in a constant bootloop, turning on and off, without showing any logo and not giving me any access to recovery. I can't even initiate fastboot.. WHAT DO I DO NOW? I really need your help with this..
AND by the way, I have a lot of experience in the matter of flashing and android development, but this is the first time I really don't know what to do to fix this issue!
Click to expand...
Click to collapse
dont panic if you have boot loop all you need to do is hard reset the phone this is dont by holding power button and vol+ till it vibrates 3 times this will switch the phone off and allow you fastboot to flash cwm recovery again and then you can recover your backup
Xperia P.... has a removable battery right, if I recall.
Remove battery, hold vol up, place battery. Phone should vibrate 3 times.
Keep finger on vol up, shove USB port in. You should get into fastboot.
If you're aiming to go back to stock, then just go into flashboot (vol down), and flash a stock ftf file.
Snowstormzzz said:
Xperia P.... has a removable battery right, if I recall.
Remove battery, hold vol up, place battery. Phone should vibrate 3 times.
Keep finger on vol up, shove USB port in. You should get into fastboot.
If you're aiming to go back to stock, then just go into flashboot (vol down), and flash a stock ftf file.
Click to expand...
Click to collapse
sorry i thort it was hard battery ( my apologies) once you have it in flash mode you can do stock ftf and cwm as you did before
Xperia P doesn't have a removable battery, the innards of the phones are about as accessible as the iphone
MadManMark said:
Xperia P doesn't have a removable battery, the innards of the phones are about as accessible as the iphone
Click to expand...
Click to collapse
Didnt think it did but I don't have one . To the open just follow my first post
Sent from my Xperia Go using xda premium
My bad my bad. Google images got me confused over the U.
have you tried hard reboot ?
keeping d power+ volume up +volume down button pressed until the fone vibrates thrice ?
if this happens that means ur phone can enter into fastboot by connecting the usb while holding the vol up button
and u can flash this kernel
http://forum.xda-developers.com/showthread.php?t=1841613
works pretty good with stock ics firmware
have tried it myself
njoi
and all the best
Hey guys,
I've got the xperia z tablet (16gb wifi only)
and I had unlocked it, the other day I saw it finally got an OTA update, so I let it update.
apparently that was a bad idea?, I was stuck with the broken android symbol every time i attempted to start the tablet..
I tried the sony software, the recovery thing it has. That has only made things worse, now the tablet refuses to start whatsoever.
Can anyone point me in the right direction? I'd appreciate it very much.
dempster said:
Hey guys,
I've got the xperia z tablet (16gb wifi only)
and I had unlocked it, the other day I saw it finally got an OTA update, so I let it update.
apparently that was a bad idea?, I was stuck with the broken android symbol every time i attempted to start the tablet..
I tried the sony software, the recovery thing it has. That has only made things worse, now the tablet refuses to start whatsoever.
Can anyone point me in the right direction? I'd appreciate it very much.
Click to expand...
Click to collapse
Tried to flash with fastboot an boot.img from CM or an other AOSP ROM, and then enter recovery...
zeus2602 said:
Tried to flash with fastboot an boot.img from CM or an other AOSP ROM, and then enter recovery...
Click to expand...
Click to collapse
My tablet won't give me so much as an led indicator of it charging.
dempster said:
My tablet won't give me so much as an led indicator of it charging.
Click to expand...
Click to collapse
If your not able to flash with fastboot (connect tablet over usb (push the boot button) an load an image file on the Tablet.
HARD-BRICK!!!
dempster said:
My tablet won't give me so much as an led indicator of it charging.
Click to expand...
Click to collapse
Yould could try and have a look at the following thread:
http://forum.xda-developers.com/showthread.php?t=1849170
Hi
I had the same issues when I flashed the wrong ROM. Nothing worked no power light or anything.
Now I can't remember exactly what I did but I started to press buttons and I'm sure that holing the power button and the vol up for a while made it start again and it displayed an error and then went into flash mode .
As I said I'm not sure which buttons I pressed but I know that I held them in for a while
Try using Flashtool... Im pretty sure you can rcover it by flashing a FTF file.
Z Ultra Z1 hardbrick
http://forum.xda-developers.com/showthread.php?t=2646405 :good:
So there is hope. :highfive:
I think I found the testpin. My sgp311 has started to blink after being dead since November, when I bricked it.
I don't have the device pack though.. Do you have any clue on how to find it? I think I just need the sgp311 SEMC package to resuscitate it now... Hopefully...
Sent from my Galaxy Nexus using Tapatalk 4
get the stock ftf file and flash it using flashtools, I was in a bootloop and it worked
i know its an old post but i have to try
i m in a boot loop and i want to find the Fed file in order to do a fastboot....
Can someone give them??
I test my tablet SGP321 with many ROMs.. I end up going to boot loop... Crashes and stuff but I always recover from it.
The things I do before doing anything insane with my tablet
1. Take backup off apps/data
2. Always enable debugging and Unknown Sources
3. Keep the backup of the ROMs
4. Always have the xperia flashtool on my computer
Here's what you can do..
Press and hold the Power button and the Volume Up button for ten seconds until you see a white light flashing three times. While doing this somewhere around in 5 seconds you'll see white led flashing once, but keep on pressing those buttons till it flashes next three times.
After that your tablet will be turned Off.
You can put your device in flash mode and flash a new ROM from Xperia flash tool.
If you get the error "Unknown sources and USB debugging must me enable for flash mode, then your option can be to flash the ROM from fastboot.
Download a ROM (CyanogenMod or any with custom recovery).
Flash the boot.img via fastboot and reboot your device.
Once done you should see a led lit up while the device is booting (pink/magenta color in case of CyanogenMod).
Press the volume up/down button and you should be able to go to recovery mode.
From here you can recover your device easily
And before you do anything make sure you've charged your device well.
Good luck
Hello guys.
Hoping on your truly support. Have the problem, which cannot solve by myself.
Was trying to flash boot.img from CWM recovery 6.0.3.0 via fastboot. It flashes succesfully, but after rebooting the tablet it doesnt show any signs of life. Was trying EMMA for solving , Flashtool to change kernel, but when plug it through usb, it haven't launched and PC don't recognize any device connected. When i press Vol+ Vol- Power at the same time LED lights with white 3 times and that all.
Was using rooted Lollipop 5.1.1 with unlocked bootloader.
Is there any possibility to reanimate it or its finished totally.
Regards.
Edit.
Many thnx 2 Alok Bajaj for his solution:
Here's what you can do..
Press and hold the Power button and the Volume Up button for ten seconds until you see a white light flashing three times. While doing this somewhere around in 5 seconds you'll see white led flashing once, but keep on pressing those buttons till it flashes next three times.
After that your tablet will be turned Off.
You can put your device in flash mode and flash a new ROM from Xperia flash tool.
If you get the error "Unknown sources and USB debugging must me enable for flash mode, then your option can be to flash the ROM from fastboot.
Download a ROM (CyanogenMod or any with custom recovery).
Flash the boot.img via fastboot and reboot your device.
Once done you should see a led lit up while the device is booting (pink/magenta color in case of CyanogenMod).
Press the volume up/down button and you should be able to go to recovery mode.
From here you can recover your device easily
And before you do anything make sure you've charged your device well.
Good luck
Cheers mate!
hi,
thanks for the tutorial, I try it but*don`t see the second three blue blinks how long usually*takes to wait for them
Hi there! I think I have hardbricked my tablet (SGP321) too. The thing is, mine won't start, no matter what I press and do. If I press the power button it blinks white and if I press the UP button with it, it blinks three times. After that nothing happens. If I connect a USB to it, it just flickers first red and then green. And thats it.
I tried to flash [7.1] CyanogenMod 14 [POLLUX/POLLUX_WINDY][UNOFFICIAL] by CaHbKaUp and chose the Pollux Version from this thread http://forum.xda-developers.com/xperia-tablet-z/general/rom-cyanogenmod-14-t3496758. I also flashed the recommended GApps.
I whiped the sd-card in recovery (twrp) first and then flashed the new rom and GApps.
I think I chose the wrong version, maybe? I flashed my tablet once and I thought I could do it again, the same way as before. Guess I was wrong.
If there is anything I can do to get this back to work, please respond!
with regards
PsyPax
seems like no one is looking at this thread anymore.
edit: Solution found. forgot to unlock bootloader... ^^;
Hardbrick too
PsyPax said:
seems like no one is looking at this thread anymore.
edit: Solution found. forgot to unlock bootloader... ^^;
Click to expand...
Click to collapse
Just ran into the same problem. So there are stil people looking
Didn't know about the bootloader.
Has Android 5.1.1 Stock rom,
rooted it
installed XZDualrecovery from here:
https://forum.xda-developers.com/showthread.php?t=2261606
Then it showed up twrp and I flashed lineage-14.1-20170417-UNOFFICIAL-pollux.zip
ticked "reboot" and ??? nothing
So what are the steps now to get it running again?
baarbaar said:
So what are the steps now to get it running again?
Click to expand...
Click to collapse
Reflash device with Flashtool.
You can't flash custom ROMs with XZDR recovery.