Hi !
Today the screen of my Cubot One went black, when I turn it on and off the problem remains, I can still lock the screen.
I downloaded a ROM and I tried installing it with both "Smart Phone Flash Tool" and "SP Flash tool" (Or maybe it is 2 different versions of the same software).
I load the scatter file but when I hit the "download' button nothing happens...
Can you please help me with my problem ?
Edit: Now I get this message: "ENABLE DRAM FAILED!"
rscredin The
up
My phone is experimenting some similar issue
I tried to change the recovery in my cubot one (the grey one), supossedly it has the mt6589t SoC, but every try failed, then I thought to change the firmware (the firmware the phone had was G800_CUBOT_D1_V1.3_"some_number_here"_MJK), with the firmware G800_CUBOT_D1_V0.8_20140124_MJK, i employed the SP tools without problem, the download was succefully, the i put the battery on again, then i switched it on, the telephone started, the screen lites on, but the screen keeps black, it sounds like boots normally, even the unlock screen sound normal, but there is no image in the screen, I've looked for the newer firmware everywhere but I did not found it, somebody could help me, please!!!
The firmware I used to flash the phone succesfully was the cubot one turbo available in the needrom page. Maybe the newer versions of cubot one have a new graphic chip or something different.
The error...
Alastor56 said:
Hi !
Today the screen of my Cubot One went black, when I turn it on and off the problem remains, I can still lock the screen.
I downloaded a ROM and I tried installing it with both "Smart Phone Flash Tool" and "SP Flash tool" (Or maybe it is 2 different versions of the same software).
I load the scatter file but when I hit the "download' button nothing happens...
Can you please help me with my problem ?
Edit: Now I get this message: "ENABLE DRAM FAILED!"
Click to expand...
Click to collapse
The cause of this error is trying to flasn an incorrect ROM image in the device, there are a lot of versions of cubot one, did you tried the roms in needrom_com?
Same prob.
I've same problem. Only black screen (but sounds like boot normally). Did anyone resolve this issue?
any solution found?
abanuelosh said:
The cause of this error is trying to flasn an incorrect ROM image in the device, there are a lot of versions of cubot one, did you tried the roms in needrom_com?
Click to expand...
Click to collapse
hi i have same problem, i install the rom that download of needrom but not work fine, i install the rom succesfull but my screen is black, phone turns on, I can unlock and lock it, volume buttons work, but there is simply no image.
are you have any solution?
Hello people.
I have KINGZONE SM-N9002 (Clone of Samsung Galaxy Note 3) MTK6582 and today I tried to install this ROM (Android 4.4 KitKat) -> needrom.com/download/am3-kk-v1-0-for-kingzone-sm-n9002 . I did everything, wiped data/cache/ everything I needed to and installed it . Then clicked on Reboot, and what happened is that my phone doesn't reach the menu, it just reboots showing the logo screen every time constantly!!!! I clicked on restore on Recovery mode, but it seems there are no files there. I tried to to reflash my ROM using this -> needrom.com/download/kingzone-sm-n9002-mt6582 but when I do it using Flash Tools, I get the error Invalid scatter file format. Please help! I'm in terrible need of my phone and since it is a clone, I will have to send it back to China and wait ages for it get back. Plus, I'm leaving for Scotland in two weeks time so I'm in desperate need of my phone. I cannot do anything!!! I have Flash Tools and MTK Droid Tools on my PC, so can you suggest anything that can save me????
I finally managed to flash my ROM using SP Flash tools but now my screen shows something like green pixels and it doesn't respond to anything!!!! It's like my display is completely "broken".... Please help!
Hi all
I managed to find a proper CWM recovery for my device Karbon A8 which has no glitches, flashes and works properly.
So I wanted to add custom icon to it. On flashing the downloaded recovery it works correctly whereas on changing the images it doesn't work and is stuck at boot screen
So I unpacked it and then went to ramdsik-contents->res->images and replaced the icon_clockwork.png with desired file and repacked it using kitchen without receiving any errors.
After that I flashed it and rebooted the phone. Phone after showing Karbonn (splash screen) screen goes into a black screen and is stuck there :crying:
I didn't do anything else, didn't change any values just the .png's and flashed.
After that I tried many unpacking and repacking tools but no success. Same problem unpacks and repacks without erros but after flashing stuck at black screen
Can anyone please have a look at this and help.
Please help really need help.
Thanks in advance.!
I use Windows 7 (x64) on my laptop. If someone can try unpacking and adding these images and repacking in ubuntu that might solve the problem. Please anyone help Thanks
Links to images I want to add : icon_clockwork.png
stitch.png
Working Recovery.img (untouched) : Recovery.img
Recovery after repacking : New-Image.img
so you are not stuck, just flash the working recovery, pretty dramatic post imo and wrong forum.
Hello buddies,
Greetings to all from Venezuela. I have a problem with a Contixo Q103 tablet that I was messing with.
I was trying to flash a custom recovery to it and i ended up bricking the tablet. I did it accidentally with a program called Zeus Tool, wich loaded a recovery to it but the thing is that i didn't notice that it was for an A10 Processor. The tablet only shows now the Contixo logo and stays there forever.
I have searched on the internet for several days for the stock .img file for this tablet for flashing with Phoenix Suit or PhoenixCard but i haven't found anything.
I really need your help!!!
Thank You!!!
Hi
I'm new her and sorry for my bad English
I have a wiko lenny phone a few days ago my phone stuck on wiko logo on welcome screen and blocked there even if I tried to charge it battery logo appears without percentage of charging and the screen always power on and red led not working so i flashed it by sp flash tool but didn't work although sp flash tool program said phone flashed successfully!!
I can't hard reset it because it says : CANNOT GET ENCRYPT STATE
so please anyone can help me...
thanks
any help please...
I'm still waiting...
Flash
Flash the stock rom again :3 search for it on needrom
Give a flash with latest STOCK ROM for your device, after flashing still getting boot-loop give a hard reset It should work after reset.
For Flashing U need
1-USB drivers
2-Latest Flashing Tool
3-Latest Stock ROM
STOCK ROM check HERE
2nd LINK HERE
Also please provide us Complete info of your device.
Thanks