I want to install a downgrade 4.4 to 4.3. I downloaded official Firmware. But after flashing i was bricked.
258 Euros are gone. I know what i was doing.
Please help me! (( :crying::crying::crying:
How bricked is it? Can you still get into recovery? Can you at least still turn it off and on?
8080-f dead as a dodo
Hi... just came across this post and searched hi and low through all forum looking for help... I too have a yoga tab bricked, B8080-f model. The only thing it can do is connect as an unknown usb device .. or if you hold power for a minute whilst usb is plugged in... (wait for it to switch off) then unplug usb lead and plug it in again whilst holding volume up Im able to get the quallcomm emergeny port loaded 9008 on com 4.... it wont switch on... wont show the power led when plugged in... its just blank... tried holding power for 60+ seconds as someone said would exit out of meta state or something?? .... its kaput.... all i remember doing is trying to run an update over ota... it found it then dloaded it and rebooted... when installing it failed ... i dloaded a qsb update file and put in sdfuse folder....installed by pressing down volume and holding power to get into lenovo recovery partition and updated that way... once rebooted it never switched on, charged?!?!
Any help would be greatly appreciated...
afaik i just need a factory rom to flash using miflash or emmc??
Related
Hi guys.
Right now I'm having some issues with my Tablet. It seems to be bricked. I was trying to flashing it and something failed, but now my PC cannot recognize it and when I tried to turn it on or go to recovery mode, it always stays in the Android Logo (Image attached)
What can I do. I was trying to use uberizer or adb but as the tablet is not recognized by my PC, I just don't know what to do.
Thanks for the help you can give me.
abottoni said:
Hi guys.
Right now I'm having some issues with my Tablet. It seems to be bricked. I was trying to flashing it and something failed, but now my PC cannot recognize it and when I tried to turn it on or go to recovery mode, it always stays in the Android Logo (Image attached)
What can I do. I was trying to use uberizer or adb but as the tablet is not recognized by my PC, I just don't know what to do.
Thanks for the help you can give me.
Click to expand...
Click to collapse
What brand is that tablet? Specs on it? Looks identical to mine. I got mine to flash by using livesuit and the faaastjb v2.5. Start livesuit, select your rom image that you choose. Make sure tablet is unplugged from usb, but plugged into charger, and it is off. Hold the volume up button, then plug the usb in (computer and tablet). Press the power button repeatedly until you hear the windows sound when you plug in a usb device. Once you hear this, stop pressing power, and let go of the volume up button. You should hear the sound in windows like its disconnected, then reconnected and then livesuit will ask if you want a complete flash (erase and flash) or upgrade. Then just let it go.
Hopefully this helps you, and if you do have the same tablet as me, I would be very grateful if you would send me a factory dump so I can get proper drivers!
Hi Guys, greetings from India!
I have a E970 which I unfortunately bricked ( in what seems to be a hard brick) during flashing an updated ROM. The phone screen now does not turn on at all, though when I connect it to my computer the power button led flickers on and off, and the PC responds as if a removable device is getting attached to it and being removed in quick succession.
In Device Manager I can see that the phone gets recognized as QHUSB_DLOAD.
When I tried to run the unbrick process via LGNPST, the phone name flashes along with the COM port name in the software, then disappears, and then comes back again. Moreover, the process errors out at 85% but pressing the power button does nothing.
Since the screen does not turn on, I am not sure whether my phone goes into a download mode or not.
So - is the phone recoverable at all or is it all over? Please help.
Thank you.
Chironx2012 said:
Hi Guys, greetings from India!
I have a E970 which I unfortunately bricked ( in what seems to be a hard brick) during flashing an updated ROM. The phone screen now does not turn on at all, though when I connect it to my computer the power button led flickers on and off, and the PC responds as if a removable device is getting attached to it and being removed in quick succession.
In Device Manager I can see that the phone gets recognized as QHUSB_DLOAD.
When I tried to run the unbrick process via LGNPST, the phone name flashes along with the COM port name in the software, then disappears, and then comes back again. Moreover, the process errors out at 85% but pressing the power button does nothing.
Since the screen does not turn on, I am not sure whether my phone goes into a download mode or not.
So - is the phone recoverable at all or is it all over? Please help.
Thank you.
Click to expand...
Click to collapse
If device mgr is seeing the phone as qhusb, you done did bricked your phone. You need to jtag it to fix it. Your best bet would be to look into this... http://mobiletechvideos.mybigcommerce.com/lg-optimus-g-jtag-brick-repair/
Hello to all,I am in a serious trouble with my samsung galaxy player 5.0 International China version . I rooted this with super one click.And it was successful and there was no problem.But as soon as I overwrote a file in lib folder of system,it got stuck.I tapped the power key and the screens light was gone.I again tapped but there was no response.So I held the power key for a while and the device restarted.But it got stuck on samsung logo and began to restart again and again.So I took it to download mode and tried to nand erase with odin,I thought it could format the device and my device would be fixed.But it took some time and I closed odin.Then I held the power key and it restarted with a black screen containing a picture of malfunctioning connection between a phone and computer at its middle.Then I again tried to t-flash it and again closed it without completion because my notebook had no charge.After that I flashed my device with the YP-G70-Kernel-r14 and it restarted with download mode.But if I hold the power key for a while it restart and again go to the brick showing screen(I heard that this brick is called soft brick).I downloaded two stock rom STOCK_G70XXKPH_G70XXKPH_XEF and G70XXKPL_G70XXKPL_XEF.I tried to flash them in my device with odin and they succeeded.But none of them could fix my problem.They remain in download mode and if I hold the power key the device again go to the soft bricked screen.My device isn't force shutting down.If I hold the power key the screen goes and again lights up with the bricked screen.Now,my device has become very hot and after 8-9 hours it has automatically turned off.But if I connect it to the charger it again lighten up with bricked screen.
Now,I am wanting to setup a clean and clear version of android 2.2/2.3.6 in my device.Is it possible?Will this fix my problem?If it does then please explain me the steps.Or if there is any other way to fix then please help me.
N.B. I am junior about andorid root,rom etc.It is the first device I rooted successfully.
Sorry for my bad and wrong English.
Please,help.I am in a bad danger.
BFahim said:
Hello to all,I am in a serious trouble with my samsung galaxy player 5.0 International China version . I rooted this with super one click.And it was successful and there was no problem.But as soon as I overwrote a file in lib folder of system,it got stuck.I tapped the power key and the screens light was gone.I again tapped but there was no response.So I held the power key for a while and the device restarted.But it got stuck on samsung logo and began to restart again and again.So I took it to download mode and tried to nand erase with odin,I thought it could format the device and my device would be fixed.But it took some time and I closed odin.Then I held the power key and it restarted with a black screen containing a picture of malfunctioning connection between a phone and computer at its middle.Then I again tried to t-flash it and again closed it without completion because my notebook had no charge.After that I flashed my device with the YP-G70-Kernel-r14 and it restarted with download mode.But if I hold the power key for a while it restart and again go to the brick showing screen(I heard that this brick is called soft brick).I downloaded two stock rom STOCK_G70XXKPH_G70XXKPH_XEF and G70XXKPL_G70XXKPL_XEF.I tried to flash them in my device with odin and they succeeded.But none of them could fix my problem.They remain in download mode and if I hold the power key the device again go to the soft bricked screen.My device isn't force shutting down.If I hold the power key the screen goes and again lights up with the bricked screen.Now,my device has become very hot and after 8-9 hours it has automatically turned off.But if I connect it to the charger it again lighten up with bricked screen.
Now,I am wanting to setup a clean and clear version of android 2.2/2.3.6 in my device.Is it possible?Will this fix my problem?If it does then please explain me the steps.Or if there is any other way to fix then please help me.
N.B. I am junior about andorid root,rom etc.It is the first device I rooted successfully.
Sorry for my bad and wrong English.
Please,help.I am in a bad danger.
Click to expand...
Click to collapse
remove your battery and wait 20 seconds plug in your charger without battery wait for 30 seconds then plug out charger then put your battery battery back then charge it try to turn it on
hope it helps
BFahim said:
Hello to all,I am in a serious trouble with my samsung galaxy player 5.0 International China version . I rooted this with super one click.And it was successful and there was no problem.But as soon as I overwrote a file in lib folder of system,it got stuck.I tapped the power key and the screens light was gone.I again tapped but there was no response.So I held the power key for a while and the device restarted.But it got stuck on samsung logo and began to restart again and again.So I took it to download mode and tried to nand erase with odin,I thought it could format the device and my device would be fixed.But it took some time and I closed odin.Then I held the power key and it restarted with a black screen containing a picture of malfunctioning connection between a phone and computer at its middle.Then I again tried to t-flash it and again closed it without completion because my notebook had no charge.After that I flashed my device with the YP-G70-Kernel-r14 and it restarted with download mode.But if I hold the power key for a while it restart and again go to the brick showing screen(I heard that this brick is called soft brick).I downloaded two stock rom STOCK_G70XXKPH_G70XXKPH_XEF and G70XXKPL_G70XXKPL_XEF.I tried to flash them in my device with odin and they succeeded.But none of them could fix my problem.They remain in download mode and if I hold the power key the device again go to the soft bricked screen.My device isn't force shutting down.If I hold the power key the screen goes and again lights up with the bricked screen.Now,my device has become very hot and after 8-9 hours it has automatically turned off.But if I connect it to the charger it again lighten up with bricked screen.
Now,I am wanting to setup a clean and clear version of android 2.2/2.3.6 in my device.Is it possible?Will this fix my problem?If it does then please explain me the steps.Or if there is any other way to fix then please help me.
N.B. I am junior about andorid root,rom etc.It is the first device I rooted successfully.
Sorry for my bad and wrong English.
Please,help.I am in a bad danger.
Click to expand...
Click to collapse
I don't have a samsung device myself but if you can get in download mode and you can from what you described. What happened is that you deleted a driver (from the lib folder) that was necessary for boot (something important). To get to stock go here http://forum.xda-developers.com/showthread.php?t=2192488 download the right Firmware for your device. And the right pit file (pit file is the partition layout of the device). Flash using the pit file you got. You will fix that. Good luck.
Stock rom and pit file downloaded
cedie said:
remove your battery and wait 20 seconds plug in your charger without battery wait for 30 seconds then plug out charger then put your battery battery back then charge it try to turn it on
hope it helps
Click to expand...
Click to collapse
So,I am in the download mode.I downloaded the firmware (XXXKPL) and the intl pit file.Now what options would be checked in odin and where will I put the firmware file(PDA or Bootloader)?The device has no charge.If I connect to the charger,it wakes up and becomes very hot than normal.And I can't turn it off.Its battery is non-removable.Thank you for your valuable help.
I tried repairing oppo joy smartphone for my cousin. The phone can turn on but remains in bootloop. Most guides said i can easily solve the problem by hard reset, holding power and volume button at same time and entering recovery mode. The problem is it won't entering the recovery mode or even the factory mode. One guide i read, the phone is essentially bricked if i am unable to access recovery mode so that makes me wonder.
However i tried another method by using software through pc. I downloaded usb driver, firmware and odin like software. I remove battery, connect usb, hold power and volume up together and pc is supposed to recognize and install driver or go through with rom installation. But nothing happened. Only a sound like a new device discovered after holding the buttons and it keeps buzzing every 2 seconds nonstop.
Please help me whether this is a sign of defeat or something can be done since i find brick is a term where a phone does not power on at all
Im sorry if this isnt the correct subforum, cant find one better as im new and in panic.
I have an Alcatel One Touch Pixi 3 (10) 8079
Recently tried to install a custom recovery with this tut: https://forum.xda-developers.com/showpost.php?p=67953659&postcount=1944 and everything was OK till it finished and then powered OFF device as there was nothing more to do...
Now it doesnt pass the start screen "Alcatel One touch powered by android" with this https://i.imgur.com/RhN9hoM.jpg IN A LOOP.
Tried to hold POWER and VOL+ even POWER and VOL- or just POWER to power off the device but theres no answer from, it just stays on the loop. If i plug the usb, windows sound of usb off and on in a loop too...
Is there something i can do? Can i get helped please? Thanks alot.
Bserda said:
Im sorry if this isnt the correct subforum, cant find one better as im new and in panic.
I have an Alcatel One Touch Pixi 3 (10) 8079
Recently tried to install a custom recovery with this tut: https://forum.xda-developers.com/showpost.php?p=67953659&postcount=1944 and everything was OK till it finished and then powered OFF device as there was nothing more to do...
Now it doesnt pass the start screen "Alcatel One touch powered by android" with this https://i.imgur.com/RhN9hoM.jpg IN A LOOP.
Tried to hold POWER and VOL+ even POWER and VOL- or just POWER to power off the device but theres no answer from, it just stays on the loop. If i plug the usb, windows sound of usb off and on in a loop too...
Is there something i can do? Can i get helped please? Thanks alot.
Click to expand...
Click to collapse
You have wrong twrp image. I had also this problem (like in your picture) and I find another twrp image and put it and now everything is OK.
If you want to use SP Flash tool you must install MTK USB Vcom drivers and also it is not bad to have Mobile_Upgrade_S_Gotu2_v5.0.6 installed (because of drivers).