Related
I unlocked my phone with the htc method. I had root, and superuser. titanium backup worked fine. I made a nandroid backup before I started messing with ROMS. I decided to flash infected's ROM first. Everything seemed to be going ok. It rebooted, and I got the cool beats animation. Then I got the htc splashscreen. then it just flipped back and forth between them for a half hour or so. something was obviously wrong. I tried rebooting the phone: same results. I can get into bootloader, both by holding volume down while powering up, and through the command prompt, via adb. I have a nandroid backup through twrp recovery, so no problem, right? well, it didn't work. So now, I can boot into the bootloader screen, but nothing else. I tried flashing a different ROM, but to no avail. Eventually, I noticed that I had htc sync running while I did all this. Did that wreck me? Any ideas what I can do now? I just tried to restore my nadroid backup again, without htc sync running, but all I get is a white htc screen. Please help me unbrick my phone!!!
whenever I try to flash ANY other rom, I get to the part where I have to use fastboot to flash the boot.img, and it says "sending boot" and just stays there forever.
Tried flashinf recovery.img, and the same thing happens. "sending recovery" and screen pause
God I hope someone smarter than me feels generous enough to help here...
Are you on windows? Did you install htc drivers?
Sent from my PG86100 using XDA App
I am on windows 7, and I have the htc drivers installed. Like I said, I successfully completed the htc unlock method. I had no problems until I tried to flash a rom
So you hold volume down and power to enter fastboot. Select fastboot by hitting power again. Then plugin usb and it should say fastboot usb. Then what command do you type after that?
Sent from my PG86100 using XDA App
now it wont even go into hboot. not with vol down and power, or through command prompt. before, it was going into hboot just fine, and I was using fastboot flash boot boot.img to flash the rom, but everything froze
now when I plug it in and use the command prompt to enter adb reboot bootloader, it just says device not found. holding power and vol does nothing
Hmmm.. Not sure why you can't get into fastboot but your using the wrong command. You want to type fastboot boot recovery.img. Recovery being the name of the recovery image in your folder.
Sent from my PG86100 using XDA App
thanks. I'll try that if I can get back into the bootloader
What you did works for that only installs the kernel. Then you need to flash the rom. I never did it that way nor do I use twrp
Sent from my PG86100 using XDA App
I did flash the rom.zip from twrp recovery. when it rebooted, it started to work, then just went into a boot loop. then I started trying to fix it, now it wont even come on
For now, I'm hoping that the battery just discharged during the process. I'm gonna let it charge for a few hours, and see what happens. I'm afraid that I might have done a battery pull in the middle of the process, though. When I first flashed the InfectedROM, the phone rebooted and got stuck in a loop between the beats graphics, and the htc quietly brilliant screen. it just kept going from one to the other. It went on for quite a while, and eventually, I think I pulled the battery to stop it. However, I was still able to get into the bootloader after this. I tried to reflash the rom, and a couple of others to no avail. When I decided to try to reflash recovery.img, is when it hit the fan, so to speak. after that, I was unable to boot into fastboot, or even get adb to recognize that there was a device there at all. Man, I hope letting the battery charge works. Like a moron, I don't have any insurance on my phone.
when I plug it in, windows intermittently makes the gong noise that something is connecting or disconnecting, and windows explorer briefly recognizes that a removeable drive is present, but I can't get the thing to charge, or turn on at all, and adb refuses to recognize that it connected, so I still cant manually put it into fastboot
well, I left the phone plugged in for about 7 hours. I hooked it up to the computer and once again tried to get into bootloader through adb. The computer said that the "daemon was started successfully" then goes right back to device not found. I guess Im screwed if no one else knows any tricks or ideas..
izzy spun said:
well, I left the phone plugged in for about 7 hours. I hooked it up to the computer and once again tried to get into bootloader through adb. The computer said that the "daemon was started successfully" then goes right back to device not found. I guess Im screwed if no one else knows any tricks or ideas..
Click to expand...
Click to collapse
Pull the battery
Wait 2 minutes.
Put battery back in.
Hold down Vol - and power.
Do not be connected to anything. And are you SURE your battery is good?
PM me if you see this and I dont answer.
I pulled the battery and waited. I even grabbed the battery out of my girl's evo3d. I can get into bootloader via the vol down, and power, but it stopas and asks if I want to update. If I say no, it just reboots to the htc screen. If I say yes, it says updating, then says press power to reboot. Then it goes directly to the htc screen and freezes. While it's in the htc screen, I can use command prompt to get it back into bootloader via the "adb reboot bootloader" command, but I can't get to my recovery menu. I was going to mount usb storage, and put another rom on the sd card, then re-flash, but it won't allow me to get to recovery
izzy spun said:
I pulled the battery and waited. I even grabbed the battery out of my girl's evo3d. I can get into bootloader via the vol down, and power, but it stopas and asks if I want to update. If I say no, it just reboots to the htc screen. If I say yes, it says updating, then says press power to reboot. Then it goes directly to the htc screen and freezes. While it's in the htc screen, I can use command prompt to get it back into bootloader via the "adb reboot bootloader" command, but I can't get to my recovery menu. I was going to mount usb storage, and put another rom on the sd card, then re-flash, but it won't allow me to get to recovery
Click to expand...
Click to collapse
Ok, soundslike you have a "PG86IMG.ZIP" on the root of your SD card. Dont worry, just swap cards with your old lady but put the ROM on it first.
You wont be able to do anything until you swap Sd cards or otherwise delete the PG86IMG.zip.
when I use command prompt to enter bootloader, I get the opening menu: bootloader, reboot, reboot booloader, and power down. If I press power to choose booloader rather than fastboot, the phone immediately goes back to asking me if I want to update, and no matter what I choose, the results are the same. it reboots to the htc screen
Hi there guys, first of all thank you all so much for the support here.
I have a problem with my atrix, i googled a lot before posting, but i still can't find a solution:
I have a atrix 4G, unlocked, was running successfully neutrino 2,8 version.
After 2 months of being (almost) fully functional, the phone crashed(i didn't do anything particular at that time, i think that i was browsing google maps) suddenly and now i have continuous boot loop, i get only the classic red dual core logo, with the "unlocked" notification over it, and then after 10-15 sec it reboots.
I try to open it with holding volume down, to enter recovery, nothing happens. It reboots again. The computer doesn't see it, in this case.
I reboot it with holding volume up, says "starting RSD protocol suppport", and pc sees it and i get the cling-clong sound of usb.
I would do the recovery using rsd, but i read that it is not for unlocked devices, is this so? What can i do in this case? Thanks a lot!!!
ergotelis said:
Hi there guys, first of all thank you all so much for the support here.
I have a problem with my atrix, i googled a lot before posting, but i still can't find a solution:
I have a atrix 4G, unlocked, was running successfully neutrino 2,8 version.
After 2 months of being (almost) fully functional, the phone crashed(i didn't do anything particular at that time, i think that i was browsing google maps) suddenly and now i have continuous boot loop, i get only the classic red dual core logo, with the "unlocked" notification over it, and then after 10-15 sec it reboots.
I try to open it with holding volume down, to enter recovery, nothing happens. It reboots again. The computer doesn't see it, in this case.
I reboot it with holding volume up, says "starting RSD protocol suppport", and pc sees it and i get the cling-clong sound of usb.
I would do the recovery using rsd, but i read that it is not for unlocked devices, is this so? What can i do in this case? Thanks a lot!!!
Click to expand...
Click to collapse
You'll probably need to flash a new recovery partition. Check out this thread:
http://forum.xda-developers.com/showthread.php?t=1950307
RaiderDuck said:
You'll probably need to flash a new recovery partition. Check out this thread:
http://forum.xda-developers.com/showthread.php?t=1950307
Click to expand...
Click to collapse
Thanks, but the problem is that this guy can get into the recovery with powering up+holding volume down button, if i understood well.but I can't!
ergotelis said:
Thanks, but the problem is that this guy can get into the recovery with powering up+holding volume down button, if i understood well.but I can't!
Click to expand...
Click to collapse
flasing a recovery is done via fastboot so you don't have to enter recovery but fastboot (hold power and volume down till it shows fastboot, then press up) .
look at this post: http://forum.xda-developers.com/showpost.php?p=33137046&postcount=10
Fix
ergotelis said:
Hi there guys, first of all thank you all so much for the support here.
I have a problem with my atrix, i googled a lot before posting, but i still can't find a solution:
I have a atrix 4G, unlocked, was running successfully neutrino 2,8 version.
After 2 months of being (almost) fully functional, the phone crashed(i didn't do anything particular at that time, i think that i was browsing google maps) suddenly and now i have continuous boot loop, i get only the classic red dual core logo, with the "unlocked" notification over it, and then after 10-15 sec it reboots.
I try to open it with holding volume down, to enter recovery, nothing happens. It reboots again. The computer doesn't see it, in this case.
I reboot it with holding volume up, says "starting RSD protocol suppport", and pc sees it and i get the cling-clong sound of usb.
I would do the recovery using rsd, but i read that it is not for unlocked devices, is this so? What can i do in this case? Thanks a lot!!!
Click to expand...
Click to collapse
hello i had this problem yesterday, it happens in neutrino rom to alot of people!
and btw i could not open recovery either
ill explain what i had to do
i had to use moto-fastboot and install a new recovery, basically your recovery is dead and your rom is unbootable
heres the steps
download the moto drivers and install
http://forum.xda-developers.com/attachment.php?attachmentid=1381183&d=1349549067
then download the motofastboot zip http://forum.xda-developers.com/attachment.php?attachmentid=1381414&d=1349555102
and create a new folder in C: (computer) called Android and then drag the files from the moto zip into android
Then download a new recovery http://www.mediafire.com/?6ww8wrjrdqq9m97
place the recovery.img into the android folder
now you have all the files needed to reflash your new recovery and fix your phone the whole idea is to reinstall recovery so you can access it and wipe and install the rom fresh again
now you need to do these steps
1) Attach your phone to the PC via USB (use a port closest to the power supply)
2) Reboot phone while holding volume down until you see "fastboot"
3) Press volume up to initiate fastboot
4) On your PC click the Start menu, then in the search box type "cmd"
5) In the command prompt type the following commands (no quotes, hit enter after each command)
6a) "cd c:/android"
6b) "moto-fastboot devices"
your CMD promt should show something like this
C:\Users\Me>cd c:/android
c:\Android>fastboot devices
TA20703SX9 fastboot
c:\Android>
now if that has all worked type the following phrases
moto-fastboot erase recovery
moto-fastboot flash recovery recovery-clockwork-6.0.1.4-maguro.img
moto-fastboot reboot
now the phone should reboot, unplug the usb and pull battery out.
put battery back in and then try to boot into recovery like you normally would (power button + Vol Down)
and your new recovery should load!
from here you can wipe your whole system which i would reccomended as your current one is corrupt and install a new rom or reflash your current on onto a clean wipe. if you dont understand how to clean wipe do all of these steps, factory reset, clear cache, clean dalvik cache then go to mounts > storage and format data + format cache + format system
now install new rom and let it boot up, should bootloop a couple of times then start! if not unplug battery from phone and ask for further assitance
Pixelguy said:
1) Attach your phone to the PC via USB (use a port closest to the power supply)
2) Reboot phone while holding volume down until you see "fastboot"
3) Press volume up to initiate fastboot
Click to expand...
Click to collapse
Thank you for your help, the problem is exactly here, i put on the usb, i power up the phone by pressing the volume down, and the phone does nothing,doesn't show the fastboot,and after 10-15 secs starts rebooting again. This is my problem!
The only response from my phone is when powering up, and pressing the volume up, it says "starting rsd protocol support"
Is there any case that my volume down is dead?
ergotelis said:
Thank you for your help, the problem is exactly here, i put on the usb, i power up the phone by pressing the volume down, and the phone does nothing,doesn't show the fastboot,and after 10-15 secs starts rebooting again. This is my problem!
The only response from my phone is when powering up, and pressing the volume up, it says "starting rsd protocol support"
Is there any case that my volume down is dead?
Click to expand...
Click to collapse
unplug usb
remove battery, then put battery back in make sure phone off (no green light)
then hold power button and vol down at the same time for a few seconds
Fastboot should appear in white writing then press up volume and it should say starting rsd protocal or something similiar
then plug in usb and follow the steps i have written above
i do exactly what you said, but doesn't show fastboot. from switched off, if i press volume up with power button, i see the message "starting rsd protocol support" .but no fastboot option!
Is there any chance that you can access adb after bootscreen? than you can use "adb reboot recovery" to get there...
jorno88 said:
Is there any chance that you can access adb after bootscreen? than you can use "adb reboot recovery" to get there...
Click to expand...
Click to collapse
When i start up phone, the only combination possible to stop restarting is by pressing power+vol up to show that with RSD. There is no other option then selectable. Power + volume down does not work, doesn't show anything, has anyone of you experienced this thing?
If the only working option you have is RSD, then I'm afraid you're stuck with having to flash a stock SBF. I hope you know/remember exactly what stock version you had installed before any modding or flashing, because the SBF has to match exactly. Choose wisely and read up as much as you can before flashing.
I have over a year now with custom roms, and i can't remember which version i had. Why do i have to find exactly the version that i had? The latest stock version won't work with rsd? It will make it hard brick?If i manage at least to recover the fastboot menus etc it would be great!
I will later also try to open it, to see if the side button "volume down" is not working,.
I have another question, in your moto atrix, if you press on startup power+vol up, are you also seeing the "starting RSD" etc option??
ergotelis said:
I have over a year now with custom roms, and i can't remember which version i had. Why do i have to find exactly the version that i had? The latest stock version won't work with rsd? It will make it hard brick?If i manage at least to recover the fastboot menus etc it would be great!
Click to expand...
Click to collapse
Yes, flashing a wrong SBF will most likely hardbrick your device.
ergotelis said:
I have another question, in your moto atrix, if you press on startup power+vol up, are you also seeing the "starting RSD" etc option??
Click to expand...
Click to collapse
Can't try right now, but as far as I know, yes, that is a standard way to enter RSD mode.
thank you, so, i know that at least my phone responds to some instructions.
Is there anyone else to suggest me to do anything else?
IN rsd mode, (other than flashing a stock random rom with chance of hardbricking,)the phone can be read by usb, can i do anything there?
ergotelis said:
IN rsd mode, (other than flashing a stock random rom with chance of hardbricking,)the phone can be read by usb, can i do anything there?
Click to expand...
Click to collapse
Sadly no. The RSD mode can only ever be used to flash SBFs. That's it. Nothing less, nothing more.
I will now try to open it to see if vol down is not working well. If it does work, i will select a stock rom 1 year old and i will flash it using rsd, and whatever happens....:good:
I disassembled the phone, the button seems to operate fine(?).
I flashed with RSDlite the 2.3.6 version, the RSD stuck to waiting for phone to restart.
The phone restarted, the "unlocked" logo disappeared.
Starts normally, passes the red motorola logo, shows the graphic of AT&T, and after ~10sec starts restarting again. Bootloop again!
At boot, pressing power+vol up, i can still get the RSD support. Pressing power+vol down does nothing, I don't see any error messages, like the ones in hard brick.
What can i do now, any ideas please!!!
try this
ergotelis said:
I disassembled the phone, the button seems to operate fine(?).
I flashed with RSDlite the 2.3.6 version, the RSD stuck to waiting for phone to restart.
The phone restarted, the "unlocked" logo disappeared.
Starts normally, passes the red motorola logo, shows the graphic of AT&T, and after ~10sec starts restarting again. Bootloop again!
At boot, pressing power+vol up, i can still get the RSD support. Pressing power+vol down does nothing, I don't see any error messages, like the ones in hard brick.
What can i do now, any ideas please!!!
Click to expand...
Click to collapse
Yesterday I had a hard time getting my phone into fastboot mode, after loading a bad SV kernel,it only wanted to start the RSD protocol mode. I eventually got into fastboot by plugging into the wall charger, then removing and installing the battery while holding the vol button. When fastboot appears, unplug the charger to allow sd access.
Thanks for the suggestion, i tried even this,it didn't work. The funny thing is that it shows the battery charging level full screen if i connect the charger, as it starts.
I noticed also that when i press vol down now, it takes longer to start and continue to the moving red logo, it stays for a while stable red,feels like it is thinking whether to start or not lol (if i don't press vol down, on the power up the red moto logo immediately starts the classic "waving" effects)
Anyone having any kind of suggestion?I guess you don't, right?
Hello, today I wanted to restore my previous CWM backup. So i started with cleaning partitions before restoring. I've begun with system and my phone hang. I waited about 30 minutes, then pulled out battery with hope I'll try again via CWM. The thing is - I can't boot it into recovery: Volume Up/Volume Down+Power leads to normal start up (LG screen and nothing further). So i connected it to PC and wanted to make it right via ADB. Unfortunely it seems I had USB Debugging turned off, and ADB isn't recognizing my phone now... What should I do now?
I have rooted D620r with unlocked bootloader.
silent_hunter said:
Hello, today I wanted to restore my previous CWM backup. So i started with cleaning partitions before restoring. I've begun with system and my phone hang. I waited about 30 minutes, then pulled out battery with hope I'll try again via CWM. The thing is - I can't boot it into recovery: Volume Up/Volume Down+Power leads to normal start up (LG screen and nothing further). So i connected it to PC and wanted to make it right via ADB. Unfortunely it seems I had USB Debugging turned off, and ADB isn't recognizing my phone now... What should I do now?
I have rooted D620r with unlocked bootloader.
Click to expand...
Click to collapse
You must never delete partitions before restoring a backup especially system!!
CWM will do that for you...
Boot your device in factory reset mode (which simply boots CWM) by doing the following key combination: (while your device is off - pull and plug the battery to be sure) press and hold Vol - and power, when you see the LG logo, release the power button and press it again. Hold them until you see the facory reset mode, then simply enter YES. It will reboot to CWM.
Vagelis1608 said:
You must never delete partitions before restoring a backup especially system!!
CWM will do that for you...
Click to expand...
Click to collapse
Weird, I was always doing this when I had HTC Desire S
Used this countless times and always worked!
Ok, i've done as You said, something like CWM loading screen appeared, and then went back to LG Screen. LG Screen standing still and nothing happens
The only good thing is that I can access ADB for 20 seconds when CWM is "loading", but no action can be executed - every command ends up with "waiting for device".
Thanks for Your reply, though! :highfive:
EDIT:
I solved my problem by using "Emergency software restore" mode featured in "LG User Support Tool". I got clean, unrooted system now and I need to modify it again but...
...THAT'S WHY I REGISTERED HERE!
Lock bootloader
Hello everyone.
I was just going to try out CM11, but got one question. Is it possible to lock the bootloader and revert everything to stock? There were some talks about new stock ROMs coming out and they might not work after a custom ROM.
i soft bricked my phone when installing the cyanangen 12 rom, it quit during the setup wizzard. The button combination of down and power release when seeing lg and repressing is not working. PleASE TELL ME i can enter twrp without having to restore my phone to stock. The phone will receive phone calls but that is all it does. otherwise it says setup wizzard quit and endlessly says this when you press ok. please help, despite being in los angeles, i have not found anybody capable of helping me.
Patrick--in so much need...
What is the repressing step? I've never heard of that. Isn't it just vol down and power, then release power while still holding vol down until recovery boots?
Also, do you have adb or fastboot installed on a pc? If so, adb reboot recovery from CMD if in android, or fastboot reboot recovery if in bootloader. Have you tried those?
patrick73csun said:
i soft bricked my phone when installing the cyanangen 12 rom, it quit during the setup wizzard. The button combination of down and power release when seeing lg and repressing is not working. PleASE TELL ME i can enter twrp without having to restore my phone to stock. The phone will receive phone calls but that is all it does. otherwise it says setup wizzard quit and endlessly says this when you press ok. please help, despite being in los angeles, i have not found anybody capable of helping me.
Patrick--in so much need...
Click to expand...
Click to collapse
You don't have to release the buttons, idk why so many people keep saying this. Should be the same as mine.. With the phone off just hold both power and volume down until you see it say Recovery Mode loading, then release. If that doesn't work then try the adb command while plugged in to your computer.
Barshalen said:
You don't have to release the buttons, idk why so many people keep saying this. Should be the same as mine.. With the phone off just hold both power and volume down until you see it say Recovery Mode loading, then release. If that doesn't work then try the adb command while plugged in to your computer.
Click to expand...
Click to collapse
Yup. Thats the same thing i was wondering. I had to use it last night. Just hold both. Easy.
Sent from rotary technology Phone
"Also, do you have adb or fastboot installed on a pc? If so, adb reboot recovery from CMD if in android, or fastboot reboot recovery if in bootloader. Have you tried those? "-----------
How do you get into bootloader if phone is bricked? It sees the phone, but it won't open up and let me look inside? Thank you
A window comes up and says that the kernal cracked.. My phone is having a hard time getting charged, could this be related?
I have an XT1526 from Freedompop. It came prerooted with TWRP installed, however SuperSU was removed. I tried to install SuperSU via Google Play, and after that the phone would not start. It would be stuck on the Moto logo. I tried to reinstall supersu via TWRP . I used this package:
SR1-SuperSU-v2.79-SR1-20161221223537.zip . The install went through, but the phone still does not start.
I tried to do something via adb/fastboot.
adb devices does not show the phone connected, however fastboot devices sees the phone connected.
fastboot reboot works too.
What should I do now?
Currently only bootloader and TWRP work. TWPR sees the content on the SD card
mzel said:
I have an XT1526 from Freedompop. It came prerooted with TWRP installed, however SuperSU was removed. I tried to install SuperSU via Google Play, and after that the phone would not start. It would be stuck on the Moto logo. I tried to reinstall supersu via TWRP . I used this package:
SR1-SuperSU-v2.79-SR1-20161221223537.zip . The install went through, but the phone still does not start.
I tried to do something via adb/fastboot.
adb devices does not show the phone connected, however fastboot devices sees the phone connected.
fastboot reboot works too.
What should I do now?
Currently only bootloader and TWRP work. TWPR sees the content on the SD card
Click to expand...
Click to collapse
Press and hold the power button on the boot animation screen until the phone is forced restarted again.... Do this until it boots completed
If the problem doesn't stop, try different version of SuperSU.... Also tell more about your ROM?
Assassin's Blood said:
Press and hold the power button on the boot animation screen until the phone is forced restarted again.... Do this until it boots completed
If the problem doesn't stop, try different version of SuperSU.... Also tell more about your ROM?
Click to expand...
Click to collapse
I have restarted the phone this way many times and it never comes past the logo. Also on the long press it does not shut down, it only restarts.
What is the version of SuperSU suitable for this phone?
I have not changed the ROM. It is whatever it came with. How can I check?
A
mzel said:
I have restarted the phone this way many times and it never comes past the logo. Also on the long press it does not shut down, it only restarts.
What is the version of SuperSU suitable for this phone?
I have not changed the ROM. It is whatever it came with. How can I check?
A
Click to expand...
Click to collapse
Check it in your settings or bootloader.... Turn off the phone and press down+ power simultaneously....
Assassin's Blood said:
Check it in your settings or bootloader.... Turn off the phone and press down+ power simultaneously....
Click to expand...
Click to collapse
With power+Volume up it goes to the Moto logo. With power+Volume Down it goes to the bootloader and shows some info. No word about the ROM. What is strange - baseband NULL.
I suppose it is some Boost ROM, but this is just my guess
Wiping the phone via TWRP and flashing the https://s3-us-west-2.amazonaws.com/supersu/download/zip/SuperSU-v2.79-201612051815.zip helped.
Thanks a lot!