AFTER FLASH IPL/SPL MY DEVICE IS BOOT IPL 3.08.1, SPL 2.18.0001 AND AFTER RESTART IS DEAD.
HOW TO FLASH BACK IPL/SPL TO 2.18.0001?
PLEASE HELP!
According to your spl, you have a G4 device. What rom did you flash?
So you are saying that the phone does NOT turn no now and all you see is a black screen when you start it?
The phone not turn on , totaly dead!
What can i do to alive again?
My phone is G4 but i flash ipl whit G3 flash and after reboot is dead.
If you flash a G4 phone with a ROM that contains IPL/GPL (as you did), you will brick your phone. Sorry, there isn't anything you can do to revive it. You can try calling your provider or whoever sold you the phone, but chances are slim as you've probably violated the warranty.
Insurance
I knew from your first post that it was bricked (became a brick) meaning it is no longer functional. The only way you can get pass this is by getting a new one if you have insurance that has accidental coverage as this was an accident.
So you knew you were flashing a G3 before you did?
hy anyone have solution for this problem?
fachry said:
hy anyone have solution for this problem?
Click to expand...
Click to collapse
There is no solution for this, it is bricked... sorry
are you sure that???
i have same problem
do we replace the flash???
tvpham said:
are you sure that???
i have same problem
do we replace the flash???
Click to expand...
Click to collapse
i'm revive with JTAG, but when upgrading software, i flash wrong Wizard G3 ipl and spl, now i have tri color boot loader, When flashing Original Firmware, it says vendor id wrong Stupid flasher. noID flasher stuck 80%
Guys, I'm frustrated now. I've refreshed the ROM of my G4 version of Dopod 818pro (2.15.0001 or something I just can't remember). Unfortunately it fails and I cannot even turn the power on. My WinCE colleague told me that the Boot Loader was damaged. I am now seeking for some place to re-program the chip and hope if someone can provide me boot loader program. I really appreciate your guys help!!!
Are your Bootloader Realy damage? You mean you cant enter it? Or you havent Power to start your Device?
SD Flashing doesnt work without Bootloader!!
JTAG Flashing (hardware nearest Flashing!!) isnt developed for G4 Plattform. (i think so ... look in the Wizard board ... they talk about JTAG flashing and Wizard G4 must simulare like Prophet G4!!)
the bootloader really damaged, I cannot enter the three stripe screen by holding CAM, PWR button and hit reset hole. Do you mean that I even cannot use JTag to burn the chip???
I do have two fully charged batteries. But it should not be a problem of battery, I tried to connect it to charger but it gives no response, no LED
Using JTAG to revive a wizard is either a myth, or an undiscovered secret. If you cant get into bootloader, your chances of reviving your device are slim.
JTAG isnt a secret ... its more like ... hardware knowlage. If you know what IC is your ROM. You can found over the IC Spec the right Pins for JTAG Programming. If i can get a G4 S200, i can try my best.
yes, I know that using Jtag to rewrite boot loader is complex, but it seems like it's my last chance. NetrunnerAT I really appreciate your help but I'm in Shanghai, China so I have to find someone locally who can help me with that. Wish me good luck and I'll keep you guys updated about the result
If I can find someone who can help Jtag my phone, where can I find the correct bootloader program for my cell? is it downloadable?
guys, I finally found a place to revive my prophet. However, they don't know how to jtag it either, neither do they have a programer to rewrite the chip because they say the programer is very very very expensive. They just changed the old chip with one which has correct ROM and now my G4 Prophet turns to a G3 one...anyway, I can use it now.
Thx!
You have change your rom and it is now G3!!
Can you say me what IC they have exchange! If i know it ... and get a damage device, its possible to found a solution for all Prophet users!
No problem, I kept the damaged IC at home, I'll check the model No. and will let you know
er... One more question, I want to dump the current ROM to my SD card, however the wiki doc says it needs to unlock G3 first. But another doc also says unlocking G3 will downgrade my OS to 1.0.13.21. It's like a kind of deadlock, can I just unlock G3 without changing OS?
uhm ... i think you must downgrade your OS first to CID unlock ... after that you can upgrade to your rom and make SD-Dump!
ok, then that is to say i'll never be able to get a backup of the ROM I currently have.
I'll wait for some weeks and will try to "torture" my prophet again. It was just fixed and I'm supposed to "rest" it for some days, but sooner or later it'll be unlocked, hey heyhey....
Hi, I'm back, the chip is a "M-System MD8832-d16-v3-xp" with a clearly name "Disk On Chip" on it, hope this can help you locate the chip
http://www.m-systems.com/NR/rdonlyr.../0/EOL_DOC_G3_P3.pdf|EOL_DiskOnChip_G3_P3.pdf
Cool ... i read some PDFs ... this is are very nice entry in the PDF!
Compatibility Issues
The recommended replacement, DiskOnChip G4 1Gb/2Gb 9x12mm FBGA, and H1 2Gb
12x18mm FBGA are ball to ball compatible with DiskOnChip G3/P3 7x10mm, 9x10mm FBGA
products that are being discontinued. It is necessary to upgrade software based on TrueFFS 6.2.x
to TrueFFS 6.3.2 and above when upgrading to DiskOnChip G4.
If the different betwen G3 and G4 is the TrueFFS Driver and the G4/H1 is Pin Conpatibel ... possible if i get a half damage device i try to solder a H1 DOC on the PBC and reformat it.
[edit]Holly ****! THX i have found the Migration Document with JTAG Pins!!!
http://www.m-systems.com/NR/rdonlyr...MigrationGuideDOC_G4_1Gb_to_H3_1Gb_Rev0.2.pdf
how are you going to access the pins on a FBGA?
yanuk said:
how are you going to access the pins on a FBGA?
Click to expand...
Click to collapse
you dont. you take a bricked one, de-solder it, and manually trace them to somewhere on the motherboard using a multimeter.
can any body help me with a jtag points for a g4 wizard doomed with a incorrect ipl
Give me a damage Wizard board and i say the JTAG Pins! G4 and G3 have the same JTAG Pins.
I search for a damage Prophet to but i doesnt want pay over 80€ for a community project without any payment. It some on give me a wizard or prophet Board ... i desolder the IC ... search for JTAG Pins ... and reflash it ... send it back but working :->
the device doesnt damage if i resolder the DOC ... i have the right soldering mashine.
NetrunnerAT
Where you saw on DOC points jtag ?
You need the signals TDO TCK TMS TRST TDI.
DOC only memory and there no these signal.
What jtag you will use? And no program for flash DOC through jtag - see about Universal jtag.
Greetings,
Strange HTC device came to me.. It's a GENE HT7xxx
doesnt turn on.. I've readed forums, using search button and applied things that I learn, but this is the problem:
ONBL 0.87.1000
SPL 1.07.1000 MFG
I applied everything: Nothing works.
Using RUU with HSPL Orekof / Olipro..... Nothing!! (says INVALID COMMAND)
Some help to fix it ?
I dont know if the device is strange or not, but its onbl is certainly messed up and cant be repaired without taking it to the service center.
Or through the JTAG method.
well, i ve tried JTAG method but I think im missing something.. I get no luck with that
hi,
does anyone can help please?
i have done hardspl and then tryed to permanent unlock cid.
after it failed, my phone only starts in bootloader mode.
i tryed to flash many roms, but phone doesn't start.
only bootloader appears.
what can i do? please help me. anyone must know what to do...please don't let me kick the phone on the wall
greetz
I told you in the other thread “YOU BRICKED YOUR PHONE” the warning was clear that you had to remove the hard SPL and you didn’t, so now you have an expensive paper weight.
Sorry to say, nobody has been able to recover from this.
bricked is not pemanent
The only way to truly brick it is if it dont boot at all, if u have red green blue boot loader on u can flash [wizard love rom] worked for me.
deadredn209 said:
The only way to truly brick it is if it dont boot at all, if u have red green blue boot loader on u can flash [wizard love rom] worked for me.
Click to expand...
Click to collapse
You obviously didn’t brick your phone, however lenzen24 did.
lenzen24 has a G4 IPL and a G3 SPL this equals a brick, unless someone can get a G4 SPL back in the phone it can’t be recovered.
To my knowledge nobody has recovered from this.
I lent this P7510 to a friend who has hard bricked it. Sorted APX driver and installed nvflash. Now getting 'rcm version 0X4' when running 'nvflash --sync' which I guess means the bootloader is locked? Can anyone help me out further with this please?
Thanks.