Related
Phone: Htc TyTN
Basically I upgraded, and everything went well, using radio 1.43 and vp3g's wm6 rom...
Phone works very well compared to the previous 1.2x radio and now it shows "Edge" in the connection instead of "G" like it did previously...
The only problem I have is my wireless data connection no longer works...
I have 3 other TyTN's that are setup with the factory default configuration, so if data is required from them in order to setup the new one, it can be attained.
I have noticed that while using vxutil on both the new rom and the factory one, the "cellular line" modem adapter entry looks fine, all ip's are good, but there is a second one on the wm6 device, it says "cellular line 2" and this does not exist on the factory unit.
Also using the vxutil "get hmtl" function on the wm6 device works fine, it will successfully retrieve html, but when I try to browse with IE it does not work and hangs on "locating...".
Any suggestions?
Possible solution
Go to Start - Settings - Click connections in Connections tab
Create a new connection under My Work network as per instructions from ur service provider
Saved Connection ? OK!
Click on Connections again - There would be 2 tabs - Tasks and Advanced
Click advanced
Click "Select Network"
Check both the network selected are "MY WORK NETWORK"
OK
Soft Reset ur device
and u r done!!
Good Luck
Jaggi
nope, still the same problem...
I tried exporting the registry settings for the connection manager from the working TyTN to mine and it wouldn't even connect to its voice service after!
;0
I'm sure there are some specific settings in there that need to be changed (hklm\comm\comnnmgr\providers ??), I noticed that alot of the settings are for cingular...
I've got the same problem. i'm with t-mobile uk. any advice welcomed.
I've got the same problem. i'm with t-mobile uk. any advice welcomed.
found out what it was!!
I had used the first rom I came across, the vp3g with the cingular extended rom!! doh.
I just installed pro_black_3.0.1 and the newest radio 1.4.7, setup my connection as per my provider's suggetsion, and everything works 100%!!
i get 2900kbps when i'm on 3g and about 140kbps on edge, call quality is pristine and the time to live on a call is instant compared to my 1.3x radio!
highly recommended for anybody on rogers using a TyTN!! (rogers is starting to retail it now for 299$ with a contract!!)
[continued...]
1) back up everything using PPCPimBackup or similar
2) upgrade the bootloader to hard-spl-v7
3) upgrade your Radio ROM to 1.47.00.10
4) upgrade your System ROM to pro_Black_3.0.1
5) setup your rogers wireless internet connection:
cellular 3g, gprs
access point: internet.com
username: wapuser1
password: wap
6) re-run pimbackup and restore your contacts/schedule/emails/etc
7) laugh at others who are still using the rogers wm5 build from mid 2006 and the 1.3x radio that came with it.
haha funny do tell me if ur name display works with WM6
i know mine still works with WM5 had to get my phone replaced by rogers after WM6 flash
mazdaspeed said:
haha funny do tell me if ur name display works with WM6
i know mine still works with WM5 had to get my phone replaced by rogers after WM6 flash
Click to expand...
Click to collapse
lol, no everything works fine.
1.48
Actually- Radio Rom 1.48 works very well- I've been using it for a few days now. Good battery life (I recommend using a comm-manager or data app to kill HSDPA during idle standby because it does make it run out faster)
1.48 really grabs a signal and holds it- good voice quality too.
But- truth be told- 1.42 that came with it was probably just as good....
If your phone was hanging on Locating and you were using the VP3G ROM, you probably didn't disable the proxy.
VP3G cooks ROMs for AT&T use and AT&T use a proxy to connect to the internet. Rogers does not.
Theres a simple program in Programs/Proxy Manager just run it once and presto.... proxy gone and wifi as well as Rogers works fine.
Its well documented in the wiki as well.
I've used the Black ROMs and the VP3G V3 is far superior in speed and stability. Black has lots of bling but seems far to experimental for serious use.
most all threads are on how to use a 6800 as a modem for a lap top.
I need to use it for a modem on my pc. I have tried the internet sharing thing and it didnt work (probably me). what im looking for is a blow by blow breakdown on how to use it here at the house.
My wife has a few courses she is taking on line and neither of us can get on to the web site but i can using my phone so i was trying to use it as a modem so she dosent have to go anywhere to do her class.
Tregrad said:
most all threads are on how to use a 6800 as a modem for a lap top.
I need to use it for a modem on my pc. I have tried the internet sharing thing and it didnt work (probably me). what im looking for is a blow by blow breakdown on how to use it here at the house.
My wife has a few courses she is taking on line and neither of us can get on to the web site but i can using my phone so i was trying to use it as a modem so she dosent have to go anywhere to do her class.
Click to expand...
Click to collapse
The ICS thing works great and is pretty easy. Launch ICS, plug USB cable in and hit connect on 6800. Look at status on 6800 and see if it says 'connected' or 'check usb cable'. If connected then enjoy, if 'check usb cable then look in device manager on PC and figure out why , then it should work good. Or get WMWifirouter and a WIFI card for your PC and do it wireless.
Tregrad said:
most all threads are on how to use a 6800 as a modem for a lap top.
I need to use it for a modem on my pc. I have tried the internet sharing thing and it didnt work (probably me). what im looking for is a blow by blow breakdown on how to use it here at the house.
My wife has a few courses she is taking on line and neither of us can get on to the web site but i can using my phone so i was trying to use it as a modem so she dosent have to go anywhere to do her class.
Click to expand...
Click to collapse
Laptop or PC.. it works the same.
1. Make sure you have a data plan with your carrier. (No data, no go)
2. Use Internet Sharing program on 6800 - (on sprint make sure Sprint PCS is selected at network connection). Click connect
3. Connect USB cable to 6800 and PC
4. Windows XP or Vista should detect and connect automatically
5. Bring up IE or Firefox to verify and surf away.
the process is the exact same whether on a laptop or desktop. they're both computers...
as long as you have a USB port and the right drivers for your OS, you're fine. works the same.
ok cool ill give it a shot and thanks for the input. I just had no idea if they were the same or not so thanks again.
got it to work but after a bit active sync comes up and ruins it. Im getting sick of active sync getting in the way all the time, it severely gets in the way of my regular connection and basically shuts down my connection untill I unplug my phone.
Anyway, back on topic, i keep getting this error "the romote party has endd this connection.
I have and unlimited data plan with sprint.
Search for app Kill Activesync.
now im getting an error code "67 registration code error your pcs vision username and or password may be incorrect"
then this pops up....."the romote party has end this connection.
activesync is not running
Tregrad said:
now im getting an error code "67 registration code error your pcs vision username and or password may be incorrect"
then this pops up....."the romote party has end this connection.
activesync is not running
Click to expand...
Click to collapse
are you on the 3.27 radio? What rom are you on? I know DCD deletes the necessary reg keys already, so i'm guessin you are on a 3.27 radio.
3.16 rom with the 3.27 radio
when i get this error
"your pcs vision username and or password may be incorrect"
where do i put my password and username in, in the phone?
Tregrad said:
when i get this error
"your pcs vision username and or password may be incorrect"
where do i put my password and username in, in the phone?
Click to expand...
Click to collapse
Are you running Internet Sharing (Use Spint PCS connection) BEFORE you plug in your USB cable? If not, Active sync will usually automatically run.
Do a SOFT reset and try it again.
the problem is with the radio. IT's crap for internet. Go back to 2.17 if Internet connection is important.
1999TL said:
the problem is with the radio. IT's crap for internet. Go back to 2.17 if Internet connection is important.
Click to expand...
Click to collapse
I'm running 3.16 and Internet no problem.
I'm a sprint SERO user which I'm sure matters...
Back with the 2.16/2.17 versions I used USB Modem for tethering with USB and bluetooth. However I noticed the latest 3.35 and even DCD 3.0.1 I can't seem to get bluetooth tethering going at all.
Anyone figure out how to get this configuration going? I can get USB Modem to work with 3.35 but not 3.0.1 in USB mode. It gets strange 67 errors.
I tried WModem from PPC Geeks, but those instructions only seem to be applicable for Sprint's ROM.
USB Modem for either version simply refuses to enable in bluetooth mode..
I want to ditch the Sprint 3.35 ROM because it is so ridiculously slow, that it's unusable.
hceuterpe said:
I'm a sprint SERO user which I'm sure matters...
Back with the 2.16/2.17 versions I used USB Modem for tethering with USB and bluetooth. However I noticed the latest 3.35 and even DCD 3.0.1 I can't seem to get bluetooth tethering going at all.
Anyone figure out how to get this configuration going? I can get USB Modem to work with 3.35 but not 3.0.1 in USB mode. It gets strange 67 errors.
I tried WModem from PPC Geeks, but those instructions only seem to be applicable for Sprint's ROM.
USB Modem for either version simply refuses to enable in bluetooth mode..
I want to ditch the Sprint 3.35 ROM because it is so ridiculously slow, that it's unusable.
Click to expand...
Click to collapse
Ok, not sure how familiar you are with all of this stuff, but let's start with this:
There are 2 types of data plans available from sprint for your phone-
Unlimited data on your phone
Phone As Modem (PAM) Data (Tethering, Data Cards, etc).
Error 67 usually has to do with the fact that its trying to use the PAM data profile instead of the phone data.
This was ALWAYS supposed to be the case since tethering was supposed to be an additional service (with an additional fee), not included in your regular data plan. When it would use PAM, you would get charged per kb if you didn't have a PAM plan, since its not part of your data.
Your saving grace is that you have SERO.
SERO does not support the PAM plan. A rep couldn't even add it for you if they tried. So, instead of connecting and charging you per kb and having a huge bill, it just throws you a big old ERROR 67. You're lucky- had you been on a regular plan, it would have worked and possibly got stuck with a surprise in your bill.
How come it worked before?
Here's the loophole:
Our phones will only connect to one type of data at a time.
In other words, if you're already connected to the internet (checking email, web browsing, etc) it will just continue using that connection instead of hanging up and using the PAM one. I'll bet that you probably were always connected already on the 2.x roms (either because of a mail checking schedule or some app that frequently did something online) so you never ran into this problem before.
The solution?
Try opening up PIE and going to a web page so you have a valid connection. Then run Internet Sharing and see if it works. It should continue using your phone connection and not the Phone-As-Modem one.
Dishe said:
Error 67 usually has to do with the fact that its trying to use the PAM data profile instead of the phone data.
This was ALWAYS supposed to be the case since tethering was supposed to be an additional service (with an additional fee), not included in your regular data plan. When it would use PAM, you would get charged per kb if you didn't have a PAM plan, since its not part of your data.
Your saving grace is that you have SERO.
SERO does not support the PAM plan. A rep couldn't even add it for you if they tried. So, instead of connecting and charging you per kb and having a huge bill, it just throws you a big old ERROR 67. You're lucky- had you been on a regular plan, it would have worked and possibly got stuck with a surprise in your bill.
How come it worked before?
Here's the loophole:
Our phones will only connect to one type of data at a time.
In other words, if you're already connected to the internet (checking email, web browsing, etc) it will just continue using that connection instead of hanging up and using the PAM one. I'll bet that you probably were always connected already on the 2.x roms (either because of a mail checking schedule or some app that frequently did something online) so you never ran into this problem before.
The solution?
Try opening up PIE and going to a web page so you have a valid connection. Then run Internet Sharing and see if it works. It should continue using your phone connection and not the Phone-As-Modem one.
Click to expand...
Click to collapse
I had this problem also using dcd's 3.0.1 (which I mentioned in that thread). I understand and agree that the error code 67 usually indicated that PAM was being used. However, it has been determined previously that the Extension registry entry (points to rilphone.dll) was how Sprint was detecting whether you were using PAM or not. I know that dcd mentioned that he deleted this key and any other related tether detection keys, so that leads me to believe the problem is with the bluetooth stack in the Sprint official 3.35 ROM and dcd's 3.0.1 (based on 3.35) kitchen.
Edit: I am now using a ROM built from the PPCGeeks kitchen (based on no2chem's 5054) and I am having no problems connecting using bluetooth PAN from another device.
Hey all,
So I've got a small issue. I've got a Verizon XV6800 with the MR1 Rom WM6.1, Valhalla GPS server, 3.42.50 Radio.
Internet connection sharing is not working at this point. I've gone through the winmodem and internet connection sharing cab installs, registry edits, etc. None seem to help.
I previously had a ATT tilt 8925 and had no issues whatsoever tethering it to my mac by just pairing the phone, selecting to "Using a direct Higher speed connection to reach your ISP". Starting Internet Sharing on the phone, selecting Bluetooth PAN & the default data connection, then selecting connect. Then selecting "Connect to network" On the mac through the my phone listed in the bluetooth connections. That simple.
Having installed the "Internet Sharing" cab onto the phone. Internet sharing appears to work, but the phone does not advertise this service, like the ATT tilt did on ATT's network.
I've also tried a few registry edits, and used all variations of modem scripts, and got all the dialup info from verizon directly (so I know it was right ) but could not get dialup to work either. Usually not detecting a carrier, other times lockups.
I truely want to get the bluetooth-PAN working again as it did on my tilt. Anyone have this working on the MAc with a XV6800 on verizon?
i did have it working before. I'm wondering if you might be more successful with a custom rom. Verizon installs software (at least previous roms, I haven't tested the MR1 rom) that reverts reg edits and keeps it working like VzW wants it to. This could be causing problems. First check after a soft-reset to make sure your reg edits still exist.
Also I'm sure you've tried this be in Leopard's bluetooth setup delete the phone and try again. You need to select the type of device as any device in order for leopard to see it. Can you connect the device to your mac? Try that first. If you get a BT connection non-internet connection and you change your settings delete the phone and try again. I forget some of the setting I used. Also Engadget had a how to article for BT pan using the xv6700 and Tiger most of the information is still useful. It's a couple years old so you might have a hard time finding it.
Hope some of that helps.
Cycomachead said:
i did have it working before. I'm wondering if you might be more successful with a custom rom. Verizon installs software (at least previous roms, I haven't tested the MR1 rom) that reverts reg edits and keeps it working like VzW wants it to. This could be causing problems. First check after a soft-reset to make sure your reg edits still exist.
Also I'm sure you've tried this be in Leopard's bluetooth setup delete the phone and try again. You need to select the type of device as any device in order for leopard to see it. Can you connect the device to your mac? Try that first. If you get a BT connection non-internet connection and you change your settings delete the phone and try again. I forget some of the setting I used. Also Engadget had a how to article for BT pan using the xv6700 and Tiger most of the information is still useful. It's a couple years old so you might have a hard time finding it.
Hope some of that helps.
Click to expand...
Click to collapse
As mentioned, I have tried a ton of different methods to try and use the data connection, from using dialup settings, to trying to get the Bluetooth Pan working. I've removed and re-paired the device from my mac, flashed roms, hacked away at the registry a ton of times. Nothing seems to give so far.
I've got one more suggestion, found here: http://forum.xda-developers.com/showpost.php?p=1794133&postcount=29
I'm going to give this a shot tomorrow and will let you know how it goes.
Eponymous069 said:
Hey all,
So I've got a small issue. I've got a Verizon XV6800 with the MR1 Rom WM6.1, Valhalla GPS server, 3.42.50 Radio.
Internet connection sharing is not working at this point. I've gone through the winmodem and internet connection sharing cab installs, registry edits, etc. None seem to help.
I previously had a ATT tilt 8925 and had no issues whatsoever tethering it to my mac by just pairing the phone, selecting to "Using a direct Higher speed connection to reach your ISP". Starting Internet Sharing on the phone, selecting Bluetooth PAN & the default data connection, then selecting connect. Then selecting "Connect to network" On the mac through the my phone listed in the bluetooth connections. That simple.
Having installed the "Internet Sharing" cab onto the phone. Internet sharing appears to work, but the phone does not advertise this service, like the ATT tilt did on ATT's network.
Click to expand...
Click to collapse
I was wondering if you be gracious enough to share the Internet sharing CAB i only need to get it to work thought the USB cable and on a windows box, and from what im getting you got that far... JUST not working on a mac...
if thats the case, i would be ever so greatful..
Thanks
thetaz01 said:
I was wondering if you be gracious enough to share the Internet sharing CAB i only need to get it to work thought the USB cable and on a windows box, and from what im getting you got that far... JUST not working on a mac...
if thats the case, i would be ever so greatful..
Thanks
Click to expand...
Click to collapse
You can use the link from the previous post here, and just copy the dll's and exe to the Windows directory, and place teh shortcut into the Device\Windows\Start Menu\Programs\ directory.
Eponymous069 said:
You can use the link from the previous post here, and just copy the dll's and exe to the Windows directory, and place teh shortcut into the Device\Windows\Start Menu\Programs\ directory.
Click to expand...
Click to collapse
hey, ok great, i just downloaded the file, Just one question..
The file i downloaded has about a page of Reg Key changes, you didnt mention that in your "thngs to do"
Just want to see if i am to make all those changes or not.
thanks
So, your problem is in getting the internet connection to work and not connecting it to the mac, right? Does your mac recognize the phone as a modem?
If you're using MR1 I think you might need to hard reset and the soft reset right before the Verizon customizations run. You won't be able to run their apps but there won't be software to cripple the phone.
i have the same exact issue i have a new macbook pro and the bluetooth connects however the speed is slower then dial up it works perfectly however on bootcamp apple has to change the drivers
So more results.
I tried all the registry edits, (much easier with CD-Regedit so you can make the changes on your desktop) and now internet sharing does not even allow me to select a connection type, it had worked previously.
The only thing that was missing before I made the registry changes was that when I pair the phone, in the services listed, "Network Access Point" is not one of the listed services. My old phone has this service listed, and this is how I used it, where I started internet sharing on the phone, then selected the bluetooth device (phone) on the mac and selected: "Connect to Network) and it worked flawless.
Back to the drawing board. I'm going to try next to re-flash the MR1 rom and do as Cycomachead suggested and stop verizons customizations from happening.
bryanw17, what were the exact settings you used for dialup on the mac. The modem script used is probably the most important piece.
Number: #777
Username: Phonenumber (or [email protected]????)
Password: (We know this one, not sure if it's legal to post though)
Darn, I wish I could provide more help. It is indeed possible in Leopard, I had it going before I began flashing my phone - and I no longer have a data plan to test, otherwise I'd be using it a lot more!
aparently no one with a new macbook pro can get bluetooth pan to work. I have it connected however the drivers for the new macbook pro do not provide a good connection if you search the mac forums theyve been talking about it on there. I dont use a username n password however because i use the internet sharing app for the moment i am using wmwifirouter to connect online however my xv6800 doesnt charge at the same time for some reason so u can only use it till the battery dies
So some more results.
I installed ICS and all the registry edits. Then the internet Connection Sharing did not function at all. I verified the registry settings, all were fine. So no dice with me.
So back to the drawing board.
I installed a previous rom. DCD 3.2.6, and guess what? From initial flash of the phone and initial setup, no apps installed, no hacking, ICS runs and provides a network connection to my mac perfect. I also instantly notice when I pair it through bluetooth, it allows the option of "Access this device as a network port". And "Network Access point" is listed as an offered service.
I installed newer rom DCD 3.3.4, and the MR1 Rom. Neither have ICS installed initially. I can install the two files: intshare.dll and IntShrUI.exe into the windows directory without any reg edits, and then ICS works on the phone, but then pairing the phone to the Mac, and attempting to discover teh PAN service is unsuccessful. It only is discovered as a Dialup Access device, and not a "Network Access Point".
So, It appears I can get internet Sharing via Bluetooth PAN to function on the phone no matter which rom, but have not figure out how to tell the mac, or trick the mac, into thinking the "Network Access Point" service is available.
I have pulled completed registry dumps with CE-Regedit and compared the differences between the two, which there are quite a few, but not sure how to export these differences with the program so I can apply them to the other roms registry. I guess I might try a fukll backup and then restore to the new(er) rom and cross my fingers.
I'd stay with the 3.2.6 rom. and 3.42.50 Radio, with PRI 2.03, but I can only seem to make the GPS function successfully with the MR1 stock verizon rom.
Anybody want to take the two regs files compare, and see if they can find out where we can make the change to have the phone advertise the service "Network Access Point" when being paired to the mac or PC?
On one last note. I also tried the method of restoring the MR1 official rom, and then not allowing the customizations. ICS will function, but again, not advertising the service: "Network Access Point" when pairing, so it's not recognized as a valid networking method.
Where did you get those files (intshare.dll and IntShrUI.exe) to allow ICS via bluetooth?
Nevermind, I found it on PPCGeeks.
Don't know why DCD disabled the BT DUN on ICS.
I use Missing sync, and I turned on PAN then added my phone and it shoed it as a modem when I added it, but my BT connection is fairly Unrealible compared to the USB teather on Bootcamp
i was under the impression that bt pan has been whacked on macbook pro models starting from early 2008 on. anything earlier than that and it seems to work great. does anyone know why bt pan doesnt work on the newer machines and how to get it to work?
I feel like I need to 1st explain that although I don't post here often I'm not an absolute noob. I load a new ROM about every 30 days and used Tierman before advancing to Sashimi. Ever since the 6.5 roms dropped I've been unable to see my Titan from ANY laptop/desktop. I'm looking for others with the same issue and/or if this is a known issue that has been resolved.
Tried RyanMogul6800 2.2 Heavy
Tried JUSTPCTECH 6.5 Rom
Tried an un-named 6.5 Rom prior to the 21501 release
Same issue on all of these roms, SSID/PPC not visible
Device is a 6800 Alltel branded on the Alltel network
WMWifirouter version is 1.35
Tried deleting the wifi listing on the pc's/laptops
Tried re-installing WmWifirouter
Tried rebooting everything
Tried changing hardware switch to control ringer on/off instead of wifi
Tried manually powering on wifi via Comm Manager
I know wmwifirouter started out testing here so I hope they see this post but I will be accessing my paid support with wmwifirouter to submit a support ticket.
Has anyone else experienced this?
What did you do to fix it?
Try going into settings, connections, Wireless LAN, change power mode to best performance. Then go into settings, connections, wifi and if any connections are in there delete them. Make sure no connections are attempting to connect. Now turn on wifi switch and go back into wifi settings. Pick to see ad hoc only and create new. Make a name and make it an ad hoc connection, pick open connection no security protection. Finish. Now using wifi on a laptop/desktop refresh the wifi and you should now see your connection. Quick tip when using WmWifirouter. Make sure nothing is connected to your PPC's adhoc connection. Have the wifi switch enabled BEFORE turning on WMwifirouter, Once its connected you can then use a desktop or laptop and connect to the PPC, and dont turn the WIFI OFF until you have quit WMwifirouter. I use the network plugin to access shared folders on my PC to transfer music etc.. Also make sure the wifi on the PC is not set up to share its own connection. That will interfere with the networking with the wifi on the PPC. Let me know if you get wi-fi working.
Thanks and I'm trying that now..only thing is I've been using WMWifirouter cince before it was 1.0 and it always worked fine. While i'm trying your suggestion is their anything different with 6.5 that would have me manually connecting.
I'm used to setting up wmwifirouter in the office and letting 2 otherppl access it and just GO! This happens on Vista, XP, and Windows 7 (I'm an MSDN subscriber). Anyhow trying your suggestions and let me know about 6.5 if you goet a sec.
Thanks
Tried it and my network showed up for a sec but when I tried connecting it timed out and then never showed up again. USB to 3G works fine and I tried ur suggestion on Vista & XP. Still pokin away. Hope sumthin works out!
Just a side note. My wifi IP on the 6800 is always all 0's 0.0.0.0 Shouldn't it be 192.16.3.1 and DHCP is enabled BTW
I'm experiencing a similar problem and have tried several 6.5 builds, including my own from the ppckitchen. WIFI will work for some time and then stop. It will work again for a short time after rebooting but then will stop once more.
So after JustPCTechs (I prefer Ryans Rom) rom i am back on RyanMogul's heavy & it's still not working. I like many people looked at others with this issue like it's something they are doing wrong but I am an EVERY DAY user of wmwifirouter. I cancelled my itnernet at the house simply because Alltel's unlimited was so fast. I even had the kid's Xbox 360 running through it.
So I'm still stuck with no wifi for wmwifirouter. Even after Ryan's suggestions. I know other people have this problem. I just wish you guys would speak up so we can collect data on this issue and resolve it for real.
No disrespect to the very talented individuals whom have assisted me so far. You and your work are greatly appreciated.
I'm also verifying the problem exists. Also I cannot connect my home pc's internet through the USB cable to the phone anymore. I have verified this same problem with all 3 of the 6.5 roms I've tested. I tried ryan's suggestion but to no avail. Looks great though!!
For the issue of the PPC not being able to use your PC's internet through USB cable you may want to try going into settings/connections/connection settings/select network. Make the top drop down menu My work network and the bottom drop down menu make your Carrier ex:Cricket, MetroPCS, etc.. That way should use your WAP when unplugged and use the PC's home connection when plugged in. That would then be normal operation.
SOLVED:
So I was poking around in the 6800 and I never use wifi because Alltel is SOOO fast. I saw a saved network connection ON THE 6800 to wmwifirouter. I thought it was odd since I asked wmwifirouter to dynamically create the network each time instead of storing it.
After doing that I was able to consistently see the 6800 from any device.
So Comm Manager / wireless Lan/ delete wmwifirouter
I've had the usb issue a long time ago and it is not the same.
RyanMogul6800 said:
Then go into settings, connections, wifi and if any connections are in there delete them. Make sure no connections are attempting to connect.
Click to expand...
Click to collapse
If you notice i already said to delete existing wi-fi connections. So my first responses were your solution. you just overlooked it.. take care glad your sorted out.
I guess I did and let me make this real clear for anyone reading this later on. Wmwifirouter creates a wifi connection ON YOUR PPC DEVICE - TO YOUR PC DEVICE.
So when people tell you to delete all wifi connections and you delete the one on your laptop/desktop don't forget (like i did) to delete it on the ppc as well. I never knew thats how wmwifirouter worked. Learn somethin new every day. Thanks to all that helped.
ebonygirl said:
I guess I did and let me make this real clear for anyone reading this later on. Wmwifirouter creates a wifi connection ON YOUR PPC DEVICE - TO YOUR PC DEVICE.
So when people tell you to delete all wifi connections and you delete the one on your laptop/desktop don't forget (like i did) to delete it on the ppc as well. I never knew thats how wmwifirouter worked. Learn somethin new every day. Thanks to all that helped.
Click to expand...
Click to collapse
In my instructions it is telling you to delete the connections off of the PPC.. Any connection on your PC would not automatically connect unless u had a matching ad hoc connection on ur PPC. I provided the fix and u overlooked/misunderstood it. I am glad you got ur wifi back up and running.