Hi boys,
sorry my English is not very good, but I hope that somehow write.
I've installed the new firmware yesteday on my new tablet Ainol novo 10 hero - firmware had indication - "Novo1003-Hero-1219".
Installation was OK.
Then I rebooted system and tablet don't power on.....
What I have do ??? .....
Please ....
Happened to me before.
Refer here: Click Me
and here: Click Me
Solved it while referring to the guide above.
Thanks ....
I've followed the instructions, but step 5 => NOK.
This is log, when I press start in program :
-----importUpgradeFile-----filenameC:\Android\firmware\1115\Novo1003-Hero-1115.zi
-----importConfigFiles-----filenameC:\Android\AMLflash\resource\config_progress.xm
-----importUpgradeFile-----filenameC:\Android\firmware\1115\Novo1003-Hero-1115.zi
-----importUpgradeFile-----filename
[T 1][15:01:31]: load spl ...
[T 1][15:01:36]: load spl ...
[T 1][15:01:41]: load spl ...
[T 1][15:01:47]: load spl ...
[T 1][15:01:52]: load spl ...
[T 1][15:01:58]: load spl ...
[T 1][15:02:03]: load spl ...
[T 1][15:02:03]: load spl failed 20 times,maybe because rom code cannot run
[T 1][15:02:04]: failed because no connected device ,current step is 0
-----importUpgradeFile-----filename
-----importUpgradeFile-----filenameC:\Users\kwetak\Downloads\ainol_hero_1207v2_bloatfree2\1207v2_bloatfree2.zip
-----importConfigFiles-----filenameC:\Android\AMLflash\resource\config_progress.xml
-----importUpgradeFile-----filenameC:\Android\firmware\1115\Gapps_1115.zip
-----importConfigFiles-----filenameC:\Android\AMLflash\resource\config_progress.xml
log\02.11.15.09_.log
success:0 failed:0 failed postion:
Program write : Device - Disconed / Failed
nobody knows ?
Try another rom and do you have recovy on it?
Qwetak said:
nobody knows ?
Click to expand...
Click to collapse
Related
hello to all
need some help in jasjam now in bootloader mood (3 cloure screen)
when flash any wam stop in (10 - 11 - 12%) and need recovery and stay in same situation
what steps can i do to repaire my phone
need help plz
thx in advance
regards melmel
Ipl 1.04
Spl-1.40.0lipro
My Device Not Start Just Boot Loader Mood Need Help Plz
Thx
You must provide more information about your device:
what is ur previous ROM?
what is the ROM that u tried to upgrade with?
did you CID Unlocked ur device before upgrading (Hardspl)?
What is your current IPL & SPL?
do u have NO GSM error?
BTW, you should read the WIKI first!!!!!!
the proplem was that phone had no gsm
i tried alot to write radio or any wam contain radio but always failed
error and not start
it make hard spl v7 and it maked succefuly in 1 second and now phone open only boot loader not done any thing more
just boot loader mood
plz any steps
thx to all
why no one posting help plz
i wanna revive my phone
DUDE!
you cannot hardspl via bootloader.
DID you read the wiki on how to unbrick ur hermes : http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
Please follow the following steps to revive your Hermes:
1- Close the USB port on the activesync.
2- open the program MTTY (you can find it within this forum) and connect your Hermes using USB.
3- inside MTTY give this command:
task 32
if the answer is FF this means your Hermes is locked and you can go on with the steps.
now give this command in MTTY
set 16 0
the answer will be (NAND WRITE SUCCESS).
4- Disconnect your Hermes from the PC.
5- Format your micro SD card with FAT16.
6- Download the official JASJAM ROM (JASJAM_WWE_1.20.305.104.zip) and extract the file hermimg_wwe_1.20.305.104.nbh and rename it to hermimg.nbh
7-Put the file hermimg.nbh on your micro SD card and inser the card into your Hermes.
8- Reboot your Hermes and it will start the command Download, in this case press the power button to continue.
The operation will take about 20 mints to finish, if it hangs do a reset and repeat step 8.
keep repeating step 8 until the operation ends with a success.
Regards.
i open active sync
from file/connection setting/(unmark) allow usb connection
and mark on allow the connection from com 1
then opem mtty.exe
but i can't write any liter
sory cause it's the firist time to use mtty.exe and can't write commands
thx to all for replies
but need to done this plz help
Hi Guys,
I'm from Germany and I have the following problem:
I wanted to flash a WM6-Rom onto my SDA 2 / HTC Hurricane.
I did everything that was described in the tutorial but at one point I have got a problem:
When it comes to opening mtty, I can't flash the Rom.
It says:
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
Click to expand...
Click to collapse
What to do now?
I have absolutely no idea.
And I would be very glad if somebody could help me to get ANY Rom onto my device.
I'm kind of frustrated right now.
See you.
Timops
it's to small information to say anything.
you must past whole communicates from Mtty (everything)
than we can say something about it
Alright.
Then I will try it again today and post the whole mtty log.
Perhaps you can do sth. with it.
But now I've got the T-Mobile-UK-Rom (WM2003) on my device.
But I really want WM6.
1- do you unlock phone from application lock?
2- do you change CID to 11111 ?
3- do you upgrade phone with latest SPL for hurricane (for hurricane WM6)
4- do you writing commands in mtty yourself? or copy/past? (copying doesn't work)
lazaj007 said:
1- do you unlock phone from application lock?
2- do you change CID to 11111 ?
3- do you upgrade phone with latest SPL for hurricane (for hurricane WM6)
4- do you writing commands in mtty yourself? or copy/past? (copying doesn't work)
Click to expand...
Click to collapse
1- I used the cert.cab. I think this is application unlocking
2- yes I did by using SPV-Services
3- I don't know, but I used PatchedRuu.exe (I think this is that)
4- yes I write them myself
I'll try in a few minutes and post the log if it doesn't work.
But don't hesitate to post any suggestions or information.
BTW: Is my English understandable?
Now this is my log from mtty:
info 2
GetDeviceInfo=0x00000002
+ SD Controller init
- SD Controller init
+StorageInit
CMD55 failed
+ SD Controller init
- SD Controller init
+StorageInit
CMD55 failed
HTCSSuperCID ' HTCE
Cmd>format BINFS
Format BinFS partition.
Format is completed!!
Cmd>l c:\ROM.bin
clean up the image temp buffer at 0x8C080000 Length 0x01C40000
MTTYDownloadImage "c:\ROM.bin"
:F=c:\ROM.bin
start download
SAddress 82040000Hh Length 02C00000h
Before flashing new image , formatting old OS is completed!!
Start flashing new image!!!
*checksum = 0, skip checking
OEMFlashWrite(82040000h,8C080000h,01C00000h)
Update BINFS offset 0x00000000 length 0x01C00000 ...
Update BINFS success.
*checksum = 0, skip checking
Image Download Finish
OEMFlashWrite(83C40000h,8C080000h,01000000h)
Update BINFS offset 0x01C00000 length 0x01000000 ...
Flash BINFS failed.
Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
Click to expand...
Click to collapse
I think I know where the problem is:
I can't get into the bootloader correctly.
When the phone asks me if I want a IU (0) and I press the Zero-Button on the phone, nothing happens.
What to do now?
you must trying to success. maybes SPL was upgrade incorrect, go to bootloader and try to upgrade SPL by patched ruu again
I tried this so often but I don't give up!
I'll try again, maybe I'm lucky.
Who knows?
Where can i get this PatchedRUU ? I have the NBF File but i think a need the RUU program it self, but where to get it ?
here is PatcedRUU http://www.spv-developers.com/forum/attachment.php?attachmentid=65
wrong RUU!!! RUU from above will KILL your Hurricane!!
Above RUU will kill your Hurricane because it for Typhoon.
BTW: I had "CMD55 failed" error when using bad USB-cable... trying another cable made it disappear.
lazaj007 said:
you must trying to success. maybes SPL was upgrade incorrect, go to bootloader and try to upgrade SPL by patched ruu again
Click to expand...
Click to collapse
I have the same problem like Timops...Download Fails !!!
OEMFlashWrite error(12)
Error : DownloadImage return error (code = 0xFFFFFFFF)
I decide to try upgrade SPL..............but nothing...I get the "white background"
now what can I do....? USB connect not working...bootloader not working...maybe jtag?
I try to flash rom ENG to my NIKi
my version is 1.31.406
I read post "Nike SSPL, USPL and HardSPL" by jockyw2001
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-1.16-nike.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
8. you can now flash the hardspl-1.15mfg-nike.nbh by running ROMUpdateUtility.exe from flash-uspl-niki
******* but it's still 0% and still boot loader screen*****
I Hard reset my NIKI but still bootloader and show
NIKI100
SPL-1.16.0000
CPLD-4
I try to flash this rom "RUU_Nike_HTC_WWE_1[1].13.405.01_Radio_Nike_1.58.11.07_signed_Test.exe"
It's 1% only and report error 262
"ERROR [262, 276, 284, 302] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue."
How to repair this
in post "http://forum.xda-developers.com/showthread.php?t=387217" by NetrunnerAT
"1. Download MTTY and connect via USB (dont forget do disable Activ Sync!!) us command Boot, to force a OS Boot!
2. After OS is Started ... Download SSPL and Copy it to your Phone ... please remove SD Card and SIM ... Start this Program!
3. Now you are in the Bootloader but it tells something about SPL 1.16Jump ... now you can Flash Hard SPL!!! If you doesnt see 1.16Jump you CAN'T Flash HardSPL!!
4. Now you can Flash my Dumped TIM Rom!!! "
I try this It show log
"boot
Fill RSVD information for block 288 to 309
Storage start sector=0xAF00, total sector=0x103C0
Storage start block=721, total block=1039
Total Bad Block in CE: 0
Erase physical block from 1011 to 2032
si backup: Erase physical block from 2032 to 2048
Card inserted
SDHW_EnablePowerOn
SDHW_ConfigGPIO
Cmd5 CMD_TIMEOUT
Cmd8 CMD_TIMEOUT
SD Init OK
SDFATChkConf: RhOpenFile() failed NIKECONF.txt
OEMGetUpdateMode
OEMTranslateBaseAddress 23 80000000 80000000
IPLMSG:0x8:INFO: Loading image ...
IPLMSG:0x9:INFO: Jumping to image...
OEMLaunchImage 80000000
Jump to Physical Address 10300000"
and still boot loader
how to fix it's
Thank' for reply
Please tell us ... what you have done before ... step by step!!!!
If you stay in the Bootloader and MTTY "boot" doesnt work, try the oemsbl with the command "cego"
NEXT ... what NIKI you have? German? UK? TIM? Vodovone branded?
You tell us not enough, too help you!
NetrunnerAT said:
Please tell us ... what you have done before ... step by step!!!!
If you stay in the Bootloader and MTTY "boot" doesnt work, try the oemsbl with the command "cego"
NEXT ... what NIKI you have? German? UK? TIM? Vodovone branded?
You tell us not enough, too help you!
Click to expand...
Click to collapse
Sorry For My Eng = =' I'm Thai girl.
I can't Remember lang before flash becouse I don't Know ^ ^ GER or Italy or Rus Lang
It's Not Eng Lang not Vodafone Brand
I'm new bie for this model . I have Dopod 818 pro It's Easy to flash I think Niki Is same
command "cego" notwork
Can I reflash any Office Rom?
What is SPL-1.16.0000 mean It's Hard SPL,SSPL or USPL
I Try to Put camera button and power button
and Use Mtty
boot
InitDisplay: Display_Chip=1
Card inserted
SDHW_EnablePowerOn
SDHW_ConfigGPIO
Cmd5 CMD_TIMEOUT
Cmd8 CMD_TIMEOUT
SD Init OK
SDFATChkConf: RhOpenFile() failed NIKECONF.txt
OSSIReadBack ++
Read SI data from flash success
tail signature match
Checksum match
UserStorageSIPreload ++
My NIKI Can boot and Use Now
I don't Know what Lang
" A Propos de
Windows Mobile 6 Profesional
Processeur : MSM7200-400Mhz
Memorie :101.67 Mo
Conecteur d'ext. :En cours d'utilisation
Informations de L'appareil
Version de Rom :1.31.406.09
Date de Rom :10/30/07
Version de Radio 1.58.16.27
Version de prot.. 25.61.30.03w
Is lang France?
@^ ^@
Hoorayyyyyyy
My phone is back
many thank's for NetrunnerAT
1. Download MTTY and connect via USB (dont forget do disable Activ Sync!!) us command Boot, to force a OS Boot!
2. After OS is Started ... Download SSPL and Copy it to your Phone ... please remove SD Card and SIM ... Start this Program!
3. Now you are in the Bootloader but it tells something about SPL 1.16Jump ... now you can Flash Hard SPL!!! If you doesnt see 1.16Jump you CAN'T Flash HardSPL!!
4. Now you can Flash my Dumped TIM Rom!!! "
and Now I Use rom TOM_Niki-Project_WM6[1].1_WWE_16keys_signed_Ship.exe
Many many Thank For XDA - Developers
http://www.pdamobiz.com/ <- its a Thai PDA Board!
The most errors on HTC Niki are simulare with HTC Polaris and HTC Kaiser!!!
I hope this helps!
my touch dual is lock at 3 color mode
Sorry for my english....
My niki is locked afther flash for unlock it (supercid)
I've tried to install a sspl and hardspl, but all have crashed at 95%
I've tried to install hardspl renaming the file nbh in NIKEIMG.nbh from sd, but this procedure have only send me message: loading......... and nothing all.....
At this moment my niki is stopped at 3 colors mode
Have you any idea for help me?
Many thanks to all
don't have any idea for help me?
i can use my niki for stop my door?
thanks
Works very well
This really helps me out!!!! Thanks to NetrunnerAT.
but the site is in thai language
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
Have you took the sim card and memory card out?????
Jay
yes they are both out when tryign to flash, been over a week with out a working athena
cowballz69 said:
yes they are both out when tryign to flash, been over a week with out a working athena
Click to expand...
Click to collapse
try flashing your original ROM which should be found in the wiki section.
ignore what I said below and report back if you were able to load your original ROM
***Ignore this read above**Once your phone is working , do the athena wrapper which should load SPL 1.2
Also read this
http://forum.xda-developers.com/showthread.php?t=429013
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
cowballz69 said:
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
Click to expand...
Click to collapse
I think this means your phone is not unlocked
with respect to sergiopi , you cant do the mtty script.
I would suggest you msg cmonex or try to talk to her on IRC on the
dxa-devs channel
addendum
seeing that you have nothing to lose, why dont you try flashing the original rom from the sd card using the method in the wiki
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
I have the same problem.
what I do...
I have ameo t-mobile...windows mobile 5.0
run AthenaUnlocker
Step 1 make all finish noc problem
Step 2 hung up on 60 %
bootloader no problem....but can´t flash original flash always stuck at 1% and reboot...
flashing the original rom from the sd card using the method in the wiki ...
make it, but no do...on screen see
cheking...
loading....
than come on screen
0002802
ching...
loading...
not allowed
sergiopi said:
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
Click to expand...
Click to collapse
My error when it stops at 1% is "invalid vender id"
my image version is demaged
Re: Ameo from t-Mobile german - repair
________________________________________
hi
what is your CID? use mtty command "info 2" to find out.
for example, if it is TMOB_007, you have to find a shipped athena rom with that CID.
if you cannot find a matching rom, let me know, i can still help,
cmonex
HTCS Þ?ÒtHTCE
please need halp
thx
felix999
read this post http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
in mtty this can read:
when type task 32
become LEVEL: FF
when type info 2:
HTCS Þ?ÒtHTCE
my CID is 1.1
on bootscreen can see this:
ATHE100
IPL-v1.00
ATHE100
SPL-v1.10.RP00
what I do before...
Ameo WM 5.0 >>>>my mistake not update to WM6.0
run AthenaUnlocker
STEP1>>>OK
STEP2>>>by 60 % hang and stopped....
and now have the big problems.....Image ROM of t-Mobile 5.0 german demaged
can´t flash any rom´s
thx for hel or I want to pay bucks for service, when ma ameo live again...
felix999
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
this is my CID
Cmd>info 2
info 2
Wait interpreter timeout
HTCS Þ?ÒtHTCE
????????
don´t know
felix999
Athena mobile 6 > SPL 1.10
become today a answer from crazy cat, that olipro say must take an rom in athena forum....
I flaswh with so many roms...anytime same error: error 294 - invalid vendor ID.....
My SPL 1.10 >>> can´t find a rom with SPL 1.10
what rom can repair my demaged ameo?????
thx for help
felix999
problem solved with ONLINEHELP from>>>>>cmonex>>>><<:::::>><<:::E:::>><<:::R:::>><<:::F:::>><<:::E:::>><<:::C:::>><<:::T:::>>
thx
felix999
lakeman said:
try flashing your original ROM which should be found in the wiki section.
Click to expand...
Click to collapse
Is this how you solved your problem?
Hi, please I need help with unbricking my tablet Prestigio 3870c duo. I done allready repair with AML burn.tool and my tablet start recognized . After i cant find any compatible firmware for 3870 then i use flash files for 3970 because i red on the net it is simmilar but not. Touch screen not anwear and colour display look funny. After that i find it official firmware for my tablet but it been too late. Now if i want to flash with any files all stop it with error : (FIND NO UPGRADE CONFIG- please load it manually and other one: can not open the file config_progress.xml\usb_spl.bin.
Can you somebody help me with this big problem . Thank you every one who going help me
Log from AML: -----importUpgradeFile-----filenameD:\adko\hu\Prestigio_PMP3870C_Duo\Prestigi o_PMP3870C_Duo\Firmware_Pres_pmp3870c_duo\update.z ip
[T 0][13:30:36]: load spl ...
[T 0][13:30:37]: can not open the file config_progress.xml\usb_spl.bin
[T 0][13:30:43]: failed ,current step is 1
[T 0][13:49:46]: load spl ...
[T 0][13:49:46]: can not open the file config_progress.xml\usb_spl.bin
[T 0][13:49:53]: failed ,current step is 1
-----importUpgradeFile-----filenameD:\adko\hu\Prestigio_PMP3870C_Duo\Prestigi o_PMP3870C_Duo\Firmware_Pres_pmp3870c_duo\update.z ip