Hello,
I am in a serious problem my S3 got stuck at Boot Loop i have Indian 16gb S3. I downloaded the latest Stock Firmware from Sammobile and followed the instruction on XDA for installing the firmware.
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXELLC_I9300ODDEMA2_I9300DDELK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> tz.img
<ID:0/009> NAND Write Start!!
<ID:0/009> sboot.bin
<ID:0/009> system.img
<ID:0/009> boot.img
<ID:0/009> recovery.img
<ID:0/009> cache.img
<ID:0/009> hidden.img
<ID:0/009> modem.bin
<ID:0/009> RQT_CLOSE !!
<ID:0/009> RES OK !!
<ID:0/009> Completed..
<ID:0/009> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/009> Removed!!
this is my ODIN log everythg went well as i can see but its hanged at the boot loop anyone please help me out. Previously i was using Omega 44.2 rom but today i installed the Stock rom downloaded from sammobile and i got stuck please help me out please please
Try recovery and factory reset first .
Did you wipe before install ??
jje
JJEgan said:
Try recovery and factory reset first .
Did you wipe before install ??
jje
Click to expand...
Click to collapse
how to do factory reset as its getting stuck at samsung logo and yes i have wiped all the cache and have done factory reset before installing the Stock Rom
jswl.dty said:
how to do factory reset as its getting stuck at samsung logo and yes i have wiped all the cache and have done factory reset before installing the Stock Rom
Click to expand...
Click to collapse
Via recovery .
All the basics are posted in the stickied faqs and guides .
jje
Related
I tried to unroot but stuck at samsung bootscreen. Im i bricked?
just set the phone in download mode, and run odin multiloader.
Sent from my GT-I9300 using xda premium
Well i did unroot with Odin, the output:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9300_NEE_I9300XXALE8_I9300NEEALE3_I9300XXLE8.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> cache.img
<ID:0/006> hidden.img
<ID:0/006> modem.bin
<ID:0/006> recovery.img
<ID:0/006> system.img
<ID:0/006> RQT_CLOSE !!
<ID:0/006> RES OK !!
<ID:0/006> Completed..
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/006> Removed!!
Everything went great, but im still stuck at the samsung bootscreen.
Remove battery .
Boot to recovery mode factory reset.
jje
Thank you, it work.
JJEgan said:
Remove battery .
Boot to recovery mode factory reset.
jje
Click to expand...
Click to collapse
Thankyou! It worked for me as well
Hi everyone !
I have an International S3, which was running last CM10 Nightly (also last CWM Touch). I wanted to try the new Official Stock Jelly Bean rom from Poland, exactly as it is explained here: http://www.youtube.com/watch?v=_PSt8b5D2dM&feature=my_watch_later_videos&list=WL2B339812AF4545BF
http://www.androidauthority.com/galaxy-s3-i9300-android-4-1-1-jelly-bean-official-upgrade-118073/
I thing I did everything just fine, but after the flashed has finished, I'm just having a Samsung Logo lighting on and off, and nothing else is happening after, just that damn logo...
This is what Odin's message box is showing:
Code:
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXDLIB_I9300OXFDLI1_I9300XXDLIB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> system.img
<ID:0/009> NAND Write Start!!
<ID:0/009> boot.img
<ID:0/009> cache.img
<ID:0/009> hidden.img
<ID:0/009> recovery.img
<ID:0/009> modem.bin
<ID:0/009> RQT_CLOSE !!
<ID:0/009> RES OK !!
<ID:0/009> Completed..
<ID:0/009> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/009> Removed!!
<ID:0/008> Added!!
It also seems that CWM recovery has been removed. And when i use the toolkit V5, he just do not detect anything... :/
What can I do to get this fixed ? Or at least, have a working CWM recovery so I can restore the CM10 backup I made on the external SD ?
Thank you very much guys, and sorry if that has already been asked and answered somewhere else, I searched (quickly) and didn't found something like that.
Go to recovery (holding power, vol + and home button), wipe data/factory reset, cache and probably you'll be fine
Ok, so apparently I DID NOT exactly follow the same process as showed in the video above: i did not hard reset the phone...............
Anyway, as I no longer have CWM, how to do that ? .... :/
Again, thank you very much for your help !
Jiraiya-08 said:
Ok, so apparently I DID NOT exactly follow the same process as showed in the video above: i did not hard reset the phone...............
Anyway, as I no longer have CWM, how to do that ? .... :/
Again, thank you very much for your help !
Click to expand...
Click to collapse
The previous poster just told you what to do. Hold volume up button, home button & power button together until the phone reboots to recovery. Then wipe data and factory reset
Sent from my GT-I9300 using xda premium
Yeah that worked, i xas pressing the wrong volume button.... (noob here )
Thanks again to you two, i'm putting this thread solved.
Coming from LiquidSmooth 2.9
Ran triangleaway, then went into download mode, and flashed
KIES_HOME_I9300XXEMG4_I9300OXAEMG4_1314436_REV00_user_low_ship.tar.md5
Odin reported:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I9300XXEMG4_I9300OXAEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> modem.bin
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> sboot.bin
<ID:0/003> tz.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
Click to expand...
Click to collapse
Phone rebooted and now I'm just getting the Samsung logo continuously..
Power on, swirly logo, SAMSUNG, swirly logo, SAMSUNG etc..
Help Please.
How do I get this back to stock ?
Thanks
Basic faqs and guides .
http://forum.xda-developers.com/showthread.php?t=2344125
Critical you read the first two posts .
Probable fail to wipe phone .
Factory reset flash rom again
JJEgan said:
Basic faqs and guides .
http://forum.xda-developers.com/showthread.php?t=2344125
Critical you read the first two posts .
Probable fail to wipe phone .
Factory reset flash rom again
Click to expand...
Click to collapse
Thanks
Obviously should have read this before I started.
Can you advise the best way forward now. ?
Do I try again using Odin and the same file ?
Thanks
Probably should mention I was following this guide:
[Tut] Unroot the Galaxy SIII (for stock updates/warranty)
I would try flashing recovery and then wiping the phone .
JJEgan said:
I would try flashing recovery and then wiping the phone .
Click to expand...
Click to collapse
I managed to get into recovery and that told me it applied BTU.
I've cleared the data/factory reset and cache.
Phone has rebooted and now it appears to have loaded
Thanks
Hi everyone,
I'm having a great problem. Recently got rooted SIII with CF-CWM and ICS Rom. I tried to install recent update of official 4.3 announced for UK (BTU) downloaded from SamMobile.
I used ODIN 3.7 for this process. All went successfully. ODIN automatically did a factory reset but after reset phone is on Samsung logo. Logo and LED light are blinking but not going any further. And I'm unable to go into recovery as well.
Please someone help me out in this matter. I searched here but found nothing relevant. And by the way I'm in Pakistan.
Here is the log of ODIN:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGMJ9_I9300OXAGMJ9_I9300XXUGMJ9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> tz.img
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> modem.bin
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Odin does not do factory reset, boot into recovery and do it again.
Sent from my GT-I9300 using Tapatalk
boomboomer said:
Odin does not do factory reset, boot into recovery and do it again.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
thanks a lot brother
my problem is resolved.
please tell me how can I close this thread now?
How to root?
one more things.
Please guide me will the CF-Auto Root for SIII v6.4 by ChainFire work with 4.3 stock rom or not?
Check out CF's thread, I'm sure it will.
CF's Thread?
boomboomer said:
Check out CF's thread, I'm sure it will.
Click to expand...
Click to collapse
Would you like to tell me which one is CF's thread? any link for that?
faakher said:
Would you like to tell me which one is CF's thread? any link for that?
Click to expand...
Click to collapse
In development or found via the faqs and guides .
I have a Samsung Galaxy S2 i9100G model which was running Cyanogenmod Kitkat version. I wanted to get it on stock firmware. So I downloaded the stock Indian firmware (I9100GDDLS3_I9100GODDLS3_INU) and via ODIN flashed the PD file. Everything went fine according to ODIN but now my phone is just rebooting with the Samsung logo. Can anyone help me what went wrong here? Here is the details of Odin process.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GDDLS3_I9100GODDLS3_I9100GDDLS2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> MLO
<ID:0/003> NAND Write Start!!
<ID:0/003> factoryfs.img
<ID:0/003> param.lfs
<ID:0/003> Sbl.bin
<ID:0/003> zImage
<ID:0/003> modem.bin
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
choosymoron said:
I have a Samsung Galaxy S2 i9100G model which was running Cyanogenmod Kitkat version. I wanted to get it on stock firmware. So I downloaded the stock Indian firmware (I9100GDDLS3_I9100GODDLS3_INU) and via ODIN flashed the PD file. Everything went fine according to ODIN but now my phone is just rebooting with the Samsung logo. Can anyone help me what went wrong here? Here is the details of Odin process.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GDDLS3_I9100GODDLS3_I9100GDDLS2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> MLO
<ID:0/003> NAND Write Start!!
<ID:0/003> factoryfs.img
<ID:0/003> param.lfs
<ID:0/003> Sbl.bin
<ID:0/003> zImage
<ID:0/003> modem.bin
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
Just reboot to stock recovery and wipe data (factory reset) and wipe cache, and the phone will boot fine
MigoMujahid said:
Just reboot to stock recovery and wipe data (factory reset) and wipe cache, and the phone will boot fine
Click to expand...
Click to collapse
Yeah I guess that's the step missing, I will do that the only issue is my HOME button is not working right now will get it repaired and then try the same. Thanks for the reply.
Yeah booted my phone properly into stock. So for anyone who will be stuck in future and would be wondering what to do.. Wiping the data and clearing the cache is the way to go.
Thanks for the help.
greetings. this did not work for me. iv tried to wipe data and wipe cache, and even reflashed the sgs2 but nothing happened. i tried a suggestion in another forum to flash a custom recovery so that i could also wipe the dalvik cache but nothing changed. i can go into recovery just fine and i can install a custom rom as long as the zip file is in the phone memory but not on an external sd card. please help